View MAXQ314-KIT_8959549.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

_______________________________________________________________ maxim integrated products 1 for pricing, delivery, and ordering information, pl ease contact maxim direct at 1-888-629-4642, or visit maxim?s website at www.maxim-ic.com. single-phase power-measurement ic with i 2 c interface maxq314 note: some revisions of this device may incorporate deviations from published specifications known as errata. multiple revisions of any device may be simultaneously available through various sales channels. for information about device errata, go to: www.maxim-ic.com/errata . 19-5031; rev 0; 11/09 ordering information general description the maxq314 is a dedicated power-measurement ic that collects and calculates voltage, current, power, and power factor for a single-phase load. the results can be retrieved by an external master through the internal i 2 c bus. this bus is also used by the external master to configure the operation of the maxq314 and monitor the status of operations. the maxq314 performs voltage and current measure- ments using an integrated adc that can measure voltage and current. other values such as power are calculated from that data. the maxq314 also has an integrated temperature sensor that provides the die temperature on demand. the internal current amplifier produces up to 32x gain and the voltage amplifier gain is 1x. applications single-phase ac power monitoring features s high-performance, low-power dsp core s on-chip digital temperature sensor s precision internal voltage reference s active power (w), < 0.5% error s reactive power (var), < 0.7% error s apparent power (va), < 0.7% error s power factor, < 1% error s voltage rms, < 0.2% error s current rms, < 0.5% error s i 2 c-compatible serial interface s continuous output of irms in serial or pwm + denotes a lead(pb)-free/rohs-compliant package. * ep = exposed pad. maxq is a registered trademark of maxim integrated products, inc. block diagram evaluation kit available part operating voltage (v) temp range pin-package maxq314+ 3.0 to 3.6 -40 n c to +85 n c 20 tqfn-ep* maxq314 sclsda a0 a1 a2 aux rst avdd agnddvdd dgnd mux pga adc dsp watchdog timer internal reference i 2 c interface serial/pwm 16-bit maxq20 risc cpu internal 8mhz clock generator power-on reset (avdd, dvdd) bus vp vn il temp sensor downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 2 ______________________________________________________________________________________ table of contents absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 power-monitoring specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 i 2 c electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 i 2 c bus controller timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 detailed description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 clock source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 reset sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 external reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 voltage monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 i 2 c slave operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 i 2 c rate and resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 i 2 c slave address generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 i 2 c protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 data and control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 conversion to physical units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 rms current continuous output (aux pin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 applications information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 grounds and bypassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 specific design considerations for maxq314-based systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 additional documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 development and technical support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 package information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 _______________________________________________________________________________________ 3 list of figures figure 1. series resistors (r s ) for protecting against high-voltage spikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 2. i 2 c bus controller timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 3. calibration circuit example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 list of tables table 1. slave address determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 2. register set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 3. dspcfg register detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 4. calibration parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 4 ______________________________________________________________________________________ stresses beyond those listed under ?absolute maximu m ratings? may cause permanent damage to the device . these are stress ratings only, and functional operation of the device at these or any other condi tions beyond those indicated in the operational sec tions of the specifications is not implied. exposur e to absolute maximum rating conditions for extended periods may affect device reliability. voltage range on dvdd with respect to dgnd .............................................-0.3v to +4.0v voltage range on avdd with respect to agnd .............................................-0.3v to +4.0v voltage range on agnd with respect to dgnd .............................................-0.3v to +0.3v voltage range on avdd with respect to dvdd ..............................................-0.3v to +0.3v voltage range on any lead with respect to (dgnd = agnd) ...............................-0.3v to +4v operating temperature range .......................... -40 n c to +85 n c storage temperature range ........................... -65 n c to +150 n c continuous power dissipation (t a = +70 n c) 20-pin tqfn (derate 20.8mw/ n c above +70 n c) .......1667mw esd protection (human body model) ............................... q 2kv soldering temperature ......................... refer to the ipc/jedec j-std-020 specification. power-monitoring specifications (v avdd = v dvdd = 3.0v to 3.6v, t a = +25 n c.) (note 1) electrical characteristics (v avdd = v dvdd = 3.0v to 3.6v, t a = +25 n c, unless otherwise noted.) (note 2) absolute maximum ratings parameter symbol conditions min typ max units power supply digital supply voltage v dvdd 3.0 3.6 v supply current i dvdd i dvdd + i avdd , f clk = 8mhz 6.5 15.0 ma analog supply voltage v avdd 3.0 3.6 v supply voltage power-fail trip point uvlo rising, v dvdd = v avdd 2.75 2.8 2.95 v hysteresis 100 mv digital i/o input high voltage ( rst ) v ih 2.1 v input high voltage (a0, a1, a2) v ih2 v dvdd - 0.3 v input low voltage ( rst ) v il 0.8 v input low voltage (a0, a1, a2) v il2 0.3 v parameter conditions min typ max units active-power error current input dr 500:1 0.5 % reactive-power error current input dr 500:1 0.7 % apparent-power error current input dr 500:1 0.7 % power-factor error current input dr 500:1 0.1 % rms voltage error current input dr 30:1 0.2 % rms current error current input dr 500:1 0.5 % downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 _______________________________________________________________________________________ 5 electrical characteristics (continued) (v avdd = v dvdd = 3.0v to 3.6v, t a = +25 n c, unless otherwise noted.) (note 2) i 2 c electrical characteristics (v avdd = v dvdd = 3.0v to 3.6v, t a = -40 n c to +85 n c.) (note 2) parameter symbol conditions min typ max units output low voltage (aux) v ol i ol = 6ma 0.4 v input leakage (a0, a1, a2) i l -12 +12 f a input capacitance ( rst , a0, a1, a2) c in 10 pf rst pullup resistance r rst 50 150 200 k i internal oscillator oscillator frequency f sclk 7.2 8 8.8 mhz afe and analog-to-digital converter voltage range (vp) 0 1.5 v voltage range (vn) 0 1.5 v slow current channel (il) 0 1.5 v input capacitance single-ended 10 pf adc sampling rate per channel 5 ksps internal voltage reference reference accuracy t a = -40 n c to +85 n c 1.8 2.07 2.3 v temperature sensor temperature accuracy t ep = -40 n c to +85 n c 3 n c parameter symbol conditions min max units input low voltage v il_i2c 0.3 x v dvdd v input high voltage v ih_i2c 0.7 x v dvdd v input hysteresis (schmitt) v ihys_i2c v dvdd > 2v (note 1) 0.05 x v dvdd v output logic-low (open drain or open collector) v ol_i2c v dvdd > 2v, 6ma sink current 0 0.4 v input current on i/o i in_i2c input voltage from 0.1 x v dvdd to 0.9 x v dvdd -10 +10 f a i/o capacitance c io_i2c (note 1) 10 pf downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 6 ______________________________________________________________________________________ i 2 c bus controller timing (v dvdd = 3.0v to 3.6v, t a = +25 n c, unless otherwise noted. typical values are at v dvdd = 3.3v, t a = +25 n c.) (note 1, figure 2) note 1: specifications guaranteed, but not production tested. note 2: all parameters tested at t a = +25 n c. specifications over temperature are guaranteed by design. note 3: a master device must provide a hold time of at least 300ns for the sda signal (referred to v il of the scl signal) to bridge the undefined region of scl?s falling edge. note 4: i sink p 6ma. t r_i2c and t f_i2c measured between 0.3 x v dvdd and 0.7 x v dvdd. note 5: c b = total capacitance of one bus line in pf. note 6: guaranteed by design. input filters on the sda and scl pins suppress noise spikes less than 50ns. parameter symbol conditions min typ max units serial clock frequency f scl 400 khz bus free time between a stop and a start condition t buf 1.3 f s hold time (repeated) start condition t hd:sta 0.6 f s repeated start condition setup time t su:sta 0.6 f s stop condition setup time t su:sto 0.6 f s data hold time t hd:dat (note 3) 0.9 f s data setup time t su:dat 120 ns scl clock low period t low 1.3 f s scl clock high period t high 0.6 f s rise time of both sda and scl signals receiving t r_i2c (notes 4, 5) 20 + 0.1c b 300 ns fall time of both sda and scl signals receiving t f_i2c (notes 4, 5) 20 + 0.1c b 300 ns fall time of sda transmitting t f_tx (notes 4, 5) 20 + 0.1c b 250 ns pulse width of spike suppressed t sp (note 6) 50 ns capacitive load for each bus line c b (note 5) 400 pf downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 _______________________________________________________________________________________ 7 figure 1. series resistors (r s ) for protecting against high-voltage spikes figure 2. i 2 c bus controller timing diagram sda scl r s r s i 2 c device r s r s i 2 c device r p r p v dvdd maxq314 sdascl s sr p s t f_i2c t r_i2c t low t high t hd:sta t su:dat t su:sta t su:sto t buf t hd:dat downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 8 ______________________________________________________________________________________ pin configuration pin description maxq314 tqfn (5mm 5mm) top view 1920 ep* *exposed pad. + 18 17 76 8 n.c. dvdd n.c. 9 aux refa0 a1 vn 1 2 agnd 4 5 15 14 12 11 il n.c. n.c.sda scl n.c. dgnd rst 3 13 avdd 16 10 a2 vp pin name function power pins 3 dgnd digital ground. agnd and dgnd should be connected externally through a single point connection. 4 dvdd digital supply voltage. connect avdd to dvdd externally. connect a 0.1 f f capacitor to dgnd. 14 ref buffered reference output. connect this pin to agnd through a 1 f f capacitor. no other signals should be connected to this pin. 17 avdd analog supply voltage. connect avdd to dvdd externally. connect a 0.1 f f capacitor to agnd. 18 agnd analog ground. agnd and dgnd should be connected externally through a single point connection. ? ep exposed pad. connect to agnd. communication and control pins 1 aux rms current continuous output. this open-drain pin continuously outputs the value of the most recent 1 6-bit rms current measurement. if the spcfg.pwmout bit is set, the value is instead output in pwm format. 7 scl i 2 c clock line i/o 8 sda i 2 c data line i/o 10 a2 device selection address bits, input. these bits select the slave address shown in table 1. 11 a1 12 a0 13 rst active-low reset input. the cpu is held in reset when this pin is low. the pin includes pullup current source and should be driven by an open-drain external source capable of sinking in excess of 4ma. downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 _______________________________________________________________________________________ 9 detailed description the maxq314 is a dedicated analog front-end (afe) that measures voltage, current, and temperature. the internal dsp then derives calculated values. it communicates with a master device using the i 2 c communication proto- col, and continuously executes the following operations: ? scans afe channels and collects raw voltage and current samples ? calculates power (real, reactive, apparent) ? responds to register write and read commands from the master it is the master device?s responsibility to ensure that all configuration registers have been set to their correct val- ues in order to achieve the specified accuracy. clock source an internal oscillator supplies a system clock of approxi- mately 8mhz, varying slightly over temperature and volt- age. no external components are needed. reset sources external reset an external reset is generated by driving the rst pin low for at least 1 f s and remains as long as rst is held low. once the external reset has been released, all reg- isters are cleared to their default states, and the device resumes execution. voltage monitor the device is held in reset any time the power supply avdd drops below the supply voltage power-fail thresh- old. once the power supply rises above the supply volt- age power-fail level, the device exits reset, and all reg- isters are reset to their defaults and execution resumes. i 2 c slave operation the maxq314 operates as an i 2 c slave peripheral and requires an external i 2 c master. all communications between the two are performed over a standard i 2 c bus, using commands to read and write values to internal registers. these registers contain: ? operating mode settings ? calibration parameters (supplied by the master) ? read-only registers containing power, current, and voltage data during operation, voltage and current measurements are taken, filtered, and the collected data is processed. the output results then can be read by the master from read- only registers in parallel with the ongoing measurement and processing operations. the device must be initialized by the master with con- figuration and calibration parameters following every power-up or reset cycle. pin description (continued) pin name function voltage and current measurement pins 15 vn differential voltage negative input 16 vp differential voltage positive input 19 il single-ended current input, low frequency no connection pins 2, 5, 6, 9, 20 n.c. no connection. do not connect any signal to this pin. downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 10 _____________________________________________________________________________________ i 2 c rate and resets the i 2 c bus is dedicated to communications with the master device. the master device initiates all communi- cations. during an i 2 c transfer, data is transmitted and received over the serial data line (sda) with respect to a serial shift clock (scl). i 2 c transfers always start with the most significant bit and end with the least significant bit. all i 2 c transfers are 8 bits in length, followed by an ack/nack bit. the clock rate used for the i 2 c interface is determined by the bus master, but can be at most 400khz. the maxq314 can hold the scl line low while processing commands to delay reception of further data. for fre- quencies at or below 100khz, the delay can be transpar- ent, but at 400khz delays can be noticeable. a timeout provision resets the i 2 c controller if a low level is detected on the scl pin for a period of 30ms. the i 2 c controller returns to its default state, and the sda and scl pins go their idle state. i 2 c slave address generation the a2, a1, and a0 pins are latched following every reset and used to construct the 7-bit slave address as shown in table 1. the pin states are represented by l for logic 0, h for logic 1, and z for high impedance. i 2 c protocol the i 2 c protocol supports bus timeout and optionally packet-error checking. when packet-error checking is enabled by setting the pecen bit (dspcfg.3) to 1, a packet-error code (pec) byte is appended at the end of each transaction. the byte is calculated as crc-8 checksum, calculated over the entire message including the address and read/write bit. the polynomial used is x 8 + x 2 + x + 1 (the crc-8-atm hec algorithm, initial- ized to zero). commands are read and write, the command code byte being an address of a register to read/write. data length is 2 bytes for most registers, both read and write; 3 bytes for power (p, q, s, pavg), vrms, and irms read com- mands. the maxq314 could be unable to report data like power, irms, vrms, etc., immediately if the read command is received while the requested data is being calculated. in such a case, the clock line is held low until the calculation completes or a bus timeout occurs. the firmware does not support ara address or address broadcast features. table 1. slave address determination a2 a1 a0 slave address :7 l l l 60h (1100 000b) l l z 61h (1100 001b) l l h 62h (1100 010b) l z l 63h (1100 011b) l z z 64h (1100 100b) l z h 65h (1100 101b) l h l 66h (1100 110b) l h z 67h (1100 111b) l h h 68h (1101 000b) z l l 69h (1101 001b) z l z 6ah (1101 010b) z l h 6bh (1101 011b) z z l 6ch (1101 100b) z z z 6dh (1101 101b) z z h 6eh (1101 110b) z h l 6fh (1101 111b) z h z 70h (1110 000b) z h h 71h (1110 001b) h l l 72h (1110 010b) h l z 73h (1110 011b) h l h 74h (1110 100b) h z l 75h (1110 101b) h z z 76h (1110 110b) h z h 77h (1110 111b) h h l 78h (1111 000b) h h z 79h (1111 001b) h h h 7ah (1111 010b) downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 ______________________________________________________________________________________ 11 data and control registers all transactions consist of the master writing to or read- ing from data, configuration, or control registers. each register has an 8-bit address. there are several catego- ries of internal registers; read-only registers return mea- surement values taken by the device. all the read/write registers are calculation coefficients set by the master. the only exceptions are the dspcfg register, which configures operating features of the device, and the adc_az register, which resets the internal adc when it is written to. read word s addr:7 w a cmd:8 a sr addr:7 r a d0:8 a d1:8 n p read long s addr:7 w a cmd:8 a sr addr:7 r a d0:8 a d1:8 a d2:8 n p write word s addr:7 w a cmd:8 a d0:8 a d1:8 a p read word with pec s addr:7 w a cmd:8 a sr addr:7 r a d0:8 a d1:8 a pec:8 n p read long with pec s addr:7 w a cmd:8 a sr addr:7 r a d0:8 a d1:8 a d2:8 a pec:8 n p write word with pec s addr:7 w a cmd:8 a d0:8 a d1:8 a pec:8 a p a = acknowledge (ack) bit addr:7 = 7-bit device address; must match the address selected by a[2:0] cmd:8 = register/command selected in table 2 d0:8 = 8-bit data; multibyte commands can require d0, d1, d2, etc. pec:8 = 8-bit pec data n = negative acknowledge (nack) bit p = stop bit s = start bit sr = repeated start bit w = write bit downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 12 _____________________________________________________________________________________ table 2. register set name description access bits cmd code p active power r 23:0 0100 0010b (0x42) q reactive power r 23:0 0011 0010b (0x32) s apparent power r 23:0 0011 1010b (0x3a) pavg average power r 23:0 0101 1010b (0x5a) vrms rms-voltage r 23:0 0100 1010b (0x4a) irms rms-current r 23:0 0101 0010b (0x52) pf power factor; lsb = 2 -16 r 23:0 0011 1100b (0x3c) rawtemp temperature sample r 15:0 0000 0111b (0x07) pa phase-angle compensation coefficient r/w 15:0 0010 0100b (0x24) i_gain current gain coefficient r/w 15:0 0010 1011b (0x2b) v_gain voltage gain coefficient r/w 15:0 0010 1010b (0x2a) dspcfg dsp configuration r/w 15:0 0010 0010b (0x22) lpfc lowpass filter compensation r/w 15:0 0010 0011b (0x23) sumcnt number of sampling frames per dsp cycle r/w 15:0 0011 0100b (0x34) adc_az adc autozero operation. the master issues this command only when it is initializing the maxq314. any value written to this register initiates a reset of the adc, which takes approximately 1.5ms to complete. w 7:0 0000 1111b (0x0f) p_offs offset added to the p register r/w 15:0 84 p_gain gain added to the p register r/w 15:0 8c ik correction factor for irms calculation r/w 15:0 b2 igv voltage-dependent gain correction factor for irms calculation r/w 15:0 ba i_offs offset for irms calculation r/w 15:0 ac i_ov voltage-dependent offset for irms calculation r/w 15:0 ac downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 ______________________________________________________________________________________ 13 table 3. dspcfg register detail bit name description 0 disil 1 = disable il measurements 0 = enable il measurements (default) 1 reserved must be set to 1 2 reserved must be set to 0 3 pecen 1 = pec enabled for i 2 c transmission 0 = pec disabled for i 2 c transmission (default) 4 avgp 1 = begin accumulating pavg 0 = stop accumulating pavg (default) 5 avgrd 1 = pavg calculation complete 0 = pavg calculation in progress, following avgp 1 r 0 (this bit is automatically cleared the next time the master sets avgp to 1.) 6 pwmout 1 = aux pin outputs in pwm format 0 = aux pin outputs in digital format (default) 7 dispga 1 = disable gain switching 0 = enable gain switching (recommended, default) 8 ilpga 1 = pga for il = x4 (default) 0 = pga for il = x1 9 acmode 1 = ac mode 0 = dc mode (default) 10:11 reserved ? 12:15 reset_status reset status indicator. these bits allow the master to determine if the maxq314 has per- formed a reset since the last time these bits were cleared. when these bits are 1111, the maxq314 has performed a reset. after the bits have been read, the master must write 0000 to these bits to clear the reset indicator. writing to and reading from these bits does not affect processor operation or cause a reset; they are only status bits. downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 14 _____________________________________________________________________________________ calibration four parameters can be calibrated to optimize system performance. conversion to physical units the output registers are in ?meter? units, and need to be scaled with the input circuits to yield meaningful physical values. two conversion coefficients are needed: the volt- age transducer ratio (vtr) and the current transducer ratio (itr), each specifying the ratio between the input and output of the corresponding transducer. the vtr represents the input voltage that would produce a 1v signal on the vp or vn pin. the itr represents the input current that would produce a 1v signal on the il pin. for example, if the voltage-sensing circuit consists of a 749k i and 1k i resistor-divider, then vtr = 750(v/v). if the current-sensing circuit is a 20m i shunt, then 50a current would produce 1v signal on the il pin, so itr = 50(a/v). the following equations convert ?meter? units into physi- cal units: voltage (v) = vrms x vtr x v ref /2 24 current (a) = irms x itr x v ref /2 24 active power (kw) = p x vtr x itr x v ref x v ref / (10 3 x 2 24 ) reactive power (kvar) = q x vtr x itr x v ref x v ref / (10 3 x 2 24 ) apparent power (kva) = s x vtr x itr x v ref x v ref / (10 3 x 2 24 ) where v ref is the reference voltage on the ref pin in volts. the current rms correction is: irms = i_offs + i_ov x vrms + [(i_gain +igv x vrms)i mu + i k /i mu ] where i mu is the current measured in meter units before correction. voltage rms correction is: vrms = v_gain x v mu where v mu is the voltage measured in meter units before correction. active power correction is: p = v_gain x i_gain x p_gain x (p_offs + p mu ) where p mu is the active power measured in meter units before correction. apparent power is computer from the corrected voltage and current: s = vrms x irms reactive power is computer from corrected s and p: 2 2 q s p = ? table 4. calibration parameters figure 3. calibration circuit example maxq314 vpil agnd 749k ? 20m ? 1k ? lineneutral load register description v_gain voltage gain factor. this factor affects the voltage rms output and power output. the vrms output is scaled by (1 + v_gain/2 16 ). v_gain is a signed integer and defaults to 0x0000h. i_gain current gain factor. this factor affects the current rms output and power output. the irms output is scaled by (1 + i_gain/2 16 ). i_gain is a signed integer and defaults to 0x0000h. pa phase-angle compensation lpfc lowpass filter coefficient. this factor affects the lowpass filtering. it can be left unchanged for typical configura- tions. it is defined as: lpfc ~ g x f c x t fr x 2 16 , where f c is the corner frequency default value ~ 3.14 x 1.82 (hz) x 200 x e - 6 (s) x 2 16 = 75 = 0x004b downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 ______________________________________________________________________________________ 15 rms current continuous output (aux pin) the aux pin can be configured to output a 16-bit rms current value. bit time is 2000 system clocks, or a typical data rate of 4kbps. the bit format is pulse-width modula- tion, in which each bit cell is divided into four time slices. at the first time slice, the data line switches from a zero state to a one state. then, if the bit to be transmitted is a zero, the data line switches back to zero after one time slice. if the bit to be transmitted is a one, the data line switches back to zero after three time slices. a data frame consists of one complete 20-bit sample word and a frame delimiter. the frame delimiter consists of the data line idling in a low state for nominally four bit times (t bit ). the receiver detects the first rising edge of the sync field and synchronizes on the 1100 pattern. the receiver should be synchronized by the time the first data bit is available. after 16 data bits, the data line becomes idle for four t bit periods, after which the next synchronization bit begins. the aux pin can output continuous pwm as well by setting the pwmout (dspcfg.6) bit. the pwm output period is 65,535 system clocks, or 8.19ms. applications information grounds and bypassing careful pcb layout significantly minimizes system-level digital noise that could interact with the microcontroller or peripheral components. the use of multilayer boards is essential to allow the use of dedicated power planes. the area under any digital components should be a continuous ground plane if possible. keep any bypass capacitor leads short for best noise rejection and place the capacitors as close to the leads of the devices as possible. cmos design guidelines for any semiconductor require that no pin be taken above supply voltage or below ground. violation of this guideline can result in a hard failure (damage to the silicon inside the device) or a soft failure (unintentional modification of memory contents). voltage spikes above or below the device?s absolute maximum ratings can potentially cause a devastating ic latchup. microcontrollers commonly experience negative volt- age spikes through either their power pins or general- purpose i/o pins. negative voltage spikes on power pins are especially problematic as they directly couple to the internal power buses. devices such as keypads can conduct electrostatic discharges directly into the micro- controller and seriously damage the device. system designers must protect components against these tran- sients that can corrupt system memory. specific design considerations for maxq314-based systems to reduce the possibility of coupling noise into the microcontroller, the systems that use an external crystal should be designed with a crystal in a metal case that is grounded to the digital plane. doing so reduces the susceptibility of the design to fast transient noise. because the maxq314 is used in systems where high voltages are present, care must be taken to route all signal paths, both analog and digital, as far away as pos- sible from the high-voltage components. it is possible to construct more elaborate metering designs using mul- tiple maxq314 devices. this can be accomplished by using a single i 2 c bus, but with a different slave address for each device. additional documentation designers must have the following documents to full y use all the features of this device. this data sheet co ntains pin descriptions, feature overviews, and electrical speci- fications. errata sheets contain deviations from pu blished specifications. ? maxq314 data sheet, which contains electrical/timing specifications and pin descriptions ? maxq314 revision-specific errata sheet ( www.maxim-ic.com/errata ) 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 sync sample data frame gap sync sample data frame gap 1 1 0 0 d d d d d d d d d d d d d d d d l l l l 1 1 0 0 d d d d d d d d d d d d d d d d l l l l downloaded from: http:///
single-phase power-measurement ic with i 2 c interface maxq314 maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim product. no circuit patent licenses are implied. maxim reserves the right to change the circuitry and specifications without notice at any time. 16 maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 ? 2009 maxim integrated products maxim is a registered trademark of maxim integrated products, inc. development and technical support maxim offers the maxq314 evaluation kit (ev kit) as an aid in developing and prototyping applications based on the maxq314. the ev kit is a reference design from which a developer can begin designing their own sys- tem. the ev kit data sheet contains a schematic of the board that can be reviewed by engineers who want to perform a preliminary investigation of the device uses before purchasing the ev kit. technical support is available at https://support.maxim- ic.com/micro . package information for the latest package outline information and land pat- terns, go to www.maxim-ic.com/packages . note that a ?+?, ?#?, or ?-? in the package code indicates rohs status only. package drawings may show a different suf- fix character, but the drawing pertains to the package regardless of rohs status. package type package code document no. 20 tqfn-ep t2055+4 21-0140 downloaded from: http:///

▲Up To Search▲

Price & Availability of MAXQ314-KIT

	To Download MAXQ314-KIT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .