catalog symbol: HPS, HPS-ee, HPS-ff, HPS-jj, and HPS-rr panel mount agency information: ul recognized, guide izlt2, file e14853 csa certified: class 6225-01, file 47235 flammability rating: ul 94 hb panel-mount fuseholder with bayonet-type knob HPS for ?a ? 1t? to 1?a and series sc and class cc fuses form no. HPS series page 1 of 1 data sheet: 2113 bussmann 1.031" + 0.003" (26.2mm + 0.08mm) 0.187" + 0.002" (4.75mm + 0.05mm) mounting hole flange rear of panel + + 0.890" 0.003" (22.6mm 0.08mm) 1.312" + 0.003" (33.3mm + 0.08mm) 1.312" + 0.003" (33.3mm + 0.08mm) 0.88" (22.2mm) 2.81" max. (71.4mm) with fuse without fuse 2.41" max. (64.3mm) 0.80" (20.2mm) 1.78" (45.2mm) 0.180" (4.6mm) 1.125" (28.6mm) f u s e f u s e f u s e .250" .003" (6.35 .08mm) (typ. 2) mounting hole flange front of panel the only controlled copy of this data sheet is the electronic read-only version located on the bussmann network drive. all othe r copies of this document are by definition uncontrolled. this bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with desig n applications. bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. bussmann also reserves the rig ht to change or update, without notice, any technical information con- tained in this bulletin. once a product has been selected, it should be tested by the user in all possible applications. dimensional data general information: bayonet-type knob. combination ? quick-connect/solder terminals. (standard solder type terminals available.) the -ee, -jj, -ff, and -rr holders are ul recognized for applications requiring branch circuit protection. do not put tension on line (rear) terminal. electrical ratings catalog volts symbol amps ac fuse description HPS 30 (3) (4) 600 ?a x 1 ?a HPS-l 5 600 bbs, ?a ? 1 ? fuses. HPS-ee 15 600 sc 0-15, ?a ? 1 t? fuses. HPS-jj 20 600 sc 20, ?a ? 1 ?a fuses. HPS-f-ee (2) 15 600 sleeve on body, leaded for ?a ?1 t? fuses. HPS-ff (2) 30 (3) 480 sc 25 & 30, ?a ? 1 t? fuses. HPS-rr (2) 30 (3) 600 ktk-r, lp-cc, fnq-r class cc fuses. HPS-w (1) (2) 30 (3) 600 ?a ? 1 t? fuses. (1) no ul recognition (2) no csa certification (3) 20a max when used with quick connect terminals. (4) HPS rated at 25a for csa. ce logo denotes compliance with european union low voltage directive (50-1000vac, 75-1500vdc). refer to data sheet: 8002 or contact bussmann application engineering at 636-527-1270 for more information. maximum panel thickness, mounting flange in front of panel assumes pollution degree 3 per ul 840: conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation that is expected. maximum panel thickness not including any sealing gaskets. system voltage 600v 480 277 240 120 fuseholder mm inches mm inches mm inches mm inches mm inches HPS 1.50 1/32 2.39 3/32 6.66 1/4 7.21 9/32 8.69 5/8 thicker panels may be used if fuse holder load terminal is fully insulated, using a ul recognized (vw-1) insulative heat-shrink tubing, or if anticipated environment is of pollution degree 1 or 2, or if panel is nonconductive. pollution degree 2- normally, only nonconductive pollution. however, a temporary conductivity caused by condensation may be expected. pollution degree 1- no pollution or only dry, nonconductive pollution. the pollution has no influence. maximum panel thickness, mounting flange behind the panel: 5.08mm/0.200 (flush to knob collar) 6-3-04 sb04184
|
