 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| an important notice at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. advance information for pre-production products; subject to change without notice. ads114s06 , ads114s08 sbas815 ? february 2017 ads114s0x low-power, low-noise, highly integrated, 6- and 12-channel, 4-ksps, 16-bit, delta-sigma adc with pga and voltage reference 1 1 features 1 ? low power consumption: as low as 280 a ? programmable gain: 1 to 128 ? programmable data rates: 2.5 sps to 4 ksps ? simultaneous 50-hz and 60-hz rejection at 20 sps with low-latency digital filter ? analog multiplexer with 12 (ads114s08) or 6 (ads114s06) independently selectable inputs ? dual-matched programmable current sources for sensor excitation: 10 a to 2000 a ? internal reference: 2.5 v, 10 ppm/ c (max) drift ? internal oscillator: 4.096 mhz, 1.5% accuracy ? internal temperature sensor ? extended fault detection circuits ? self offset and system calibration ? four general-purpose i/os ? spi-compatible interface with optional crc ? analog supply: unipolar (2.7 v to 5.25 v) or bipolar ( 2.5 v) ? digital supply: 2.7 v to 3.6 v ? operating temperature: ? 50 c to +125 c 2 applications ? sensor transducers and transmitters: temperature, pressure, strain, flow ? plc and dcs analog input modules ? temperature controllers ? climate chambers, industrial ovens 3 description the ads114s06 and ads114s08 are precision, 16- bit, delta-sigma ( ), analog-to-digital converters (adcs) that offer low power consumption and many integrated features to reduce system cost and component count in applications measuring small- signal sensors. these adcs feature configurable digital filters that offer low-latency conversion results and 50-hz or 60-hz rejection for noisy industrial environments. a low-noise, programmable gain amplifier (pga) provides gains ranging from 1 to 128 to amplify low- level signals for resistive bridge or thermocouple applications. additionally, these devices integrate a low-drift, 2.5-v reference that reduces printed circuit board (pcb) area. finally, two programmable excitation current sources (idacs) allow for easy and accurate rtd biasing. an input multiplexer supports 12 inputs for the ads114s08 and six inputs for the ads114s06 that can be connected to the adc in any combination for design flexibility. in addition, these devices include features such as sensor burn-out detection, voltage bias for thermocouples, system monitoring, and four general-purpose i/os. the devices are offered in a leadless vqfn-32 or a tqfp-32 package. device information order number package (pin) body size ads114s0x tqfp (32) 5.0 mm 5.0 mm vqfn (32) 5.0 mm 5.0 mm functional block diagram advance information pga input mux serial interface and control cs dout/drdy sclk drdy start/sync 4.096-mhz oscillator clk refout reference detection pga rail detection aincom ain0 ain1 / gpio1 power supplies temperature sensor ads114s06 ads114s08 dvdd dgnd ain2 ain3 ain4 ain5 / refp1 / refn1 / gpio0 excitation current sources reset din refp0 refcom / gpio3 / gpio2 avss vbias avdd reference buffers reference mux 2.5-v reference refn0 ads114s08 only burnout detect burnout detect 16-bit ? adc configurable digital filter avss-sw dvdd iovdd system-, self- calibration ain9 ain6 ain7 ain8 ain11 ain10 copyright ? 2017, texas instruments incorporated productfolder ordernow technical documents tools & software support &community
2 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated table of contents 1 features .................................................................. 1 2 applications ........................................................... 1 3 description ............................................................. 1 4 revision history ..................................................... 2 5 device comparison table ..................................... 3 6 pin configuration and functions ......................... 3 7 specifications ......................................................... 5 7.1 absolute maximum ratings ..................................... 5 7.2 esd ratings .............................................................. 5 7.3 recommended operating conditions ....................... 6 7.4 thermal information .................................................. 6 7.5 electrical characteristics ........................................... 7 7.6 timing characteristics ............................................. 12 7.7 switching characteristics ........................................ 12 7.8 typical characteristics ............................................ 15 8 parameter measurement information ................ 20 8.1 noise performance ................................................. 20 9 detailed description ............................................ 25 9.1 overview ................................................................. 25 9.2 functional block diagram ....................................... 26 9.3 feature description ................................................. 27 9.4 device functional modes ........................................ 54 9.5 programming ........................................................... 58 9.6 register map ........................................................... 68 10 application and implementation ........................ 82 10.1 application information .......................................... 82 10.2 typical application ................................................ 87 10.3 do ' s and don ' ts ..................................................... 92 11 power supply recommendations ..................... 94 11.1 power supplies ..................................................... 94 11.2 power-supply sequencing .................................... 94 11.3 power-on reset .................................................... 94 11.4 power-supply decoupling ..................................... 94 12 layout ................................................................... 95 12.1 layout guidelines ................................................. 95 12.2 layout example .................................................... 96 13 device and documentation support ................. 97 13.1 device support ...................................................... 97 13.2 documentation support ........................................ 97 13.3 related links ........................................................ 97 13.4 receiving notification of documentation updates 97 13.5 community resources .......................................... 97 13.6 trademarks ........................................................... 97 13.7 electrostatic discharge caution ............................ 97 13.8 glossary ................................................................ 98 14 mechanical, packaging, and orderable information ........................................................... 98 4 revision history note: page numbers for previous revisions may differ from page numbers in the current version. date revision notes february 2017 * initial release. advance information 3 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 5 device comparison table product resolution (bits) number of inputs ads124s08 24 12 analog inputs ads124s06 24 6 analog inputs ads114s08 16 12 analog inputs ads114s06 16 6 analog inputs 6 pin configuration and functions rhb package 32-pin vqfn top view pbs package 32-pin tqfp top view note: the analog input functions (ain6 - ain11) are not available on pins 19 to 22, 31, and 32 for the ads114s06. advance information 32 refp1/ain6 9 cs 1 aincom 24 refcom 31 refn1/ain7 10 din 2 ain5 23 refout 30 refp0 11 sclk 3 ain4 22 gpio0/ain8 29 refn0 12 dout/drdy 4 ain3 21 gpio1/ain9 28 avss-sw 13 drdy 5 ain2 20 gpio2/ain10 27 avss 14 dgnd 6 ain1 19 gpio3/ain11 26 avdd 15 iovdd 7 ain0 18 reset 25 nc 16 dvdd 8 start/sync 17 clk not to scale thermal pad 32 refp1/ain6 9 cs 1 aincom 24 refcom 31 refn1/ain7 10 din 2 ain5 23 refout 30 refp0 11 sclk 3 ain4 22 gpio0/ain8 29 refn0 12 dout/drdy 4 ain3 21 gpio1/ain9 28 avss-sw 13 drdy 5 ain2 20 gpio2/ain10 27 avss 14 dgnd 6 ain1 19 gpio3/ain11 26 avdd 15 iovdd 7 ain0 18 reset 25 nc 16 dvdd 8 start/sync 17 clk not to scale 4 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) see the unused inputs and outputs section for details on how to connect unused pins. (2) general-purpose inputs and outputs use logic levels based on the analog supply. pin functions pin function description (1) no. name 1 aincom analog input common analog input for single-ended measurements 2 ain5 analog input analog input 5 3 ain4 analog input analog input 4 4 ain3 analog input analog input 3 5 ain2 analog input analog input 2 6 ain1 analog input analog input 1 7 ain0 analog input analog input 0 8 start/sync digital input start conversion 9 cs digital input chip select; active low 10 din digital input serial data input 11 sclk digital input serial clock input 12 dout/ drdy digital output serial data output combined with data ready; active low 13 drdy digital output data ready; active low 14 dgnd digital ground digital ground 15 iovdd digital supply digital i/o power supply. in case iovdd is not tied to dvdd, connect a 100-nf (or larger) capacitor to dgnd. 16 dvdd digital supply digital core power supply. connect a 100-nf (or larger) capacitor to dgnd. 17 clk digital input external clock input. connect to dgnd to use the internal oscillator. 18 reset digital input reset; active low 19 gpio3/ain11 analog input/output general-purpose i/o (2) ; analog input 11 (ads114s08 only) 20 gpio2/ain10 analog input/output general-purpose i/o (2) ; analog input 10 (ads114s08 only) 21 gpio1/ain9 analog input/output general-purpose i/o (2) ; analog input 9 (ads114s08 only) 22 gpio0/ain8 analog input/output general-purpose i/o (2) ; analog input 8 (ads114s08 only) 23 refout analog output positive voltage reference output. connect a 1- f to 47- f capacitor to refcom if the internal voltage reference is used. 24 refcom analog output negative voltage reference output. connect to avss. 25 nc ? leave unconnected or connect to avss 26 avdd analog supply positive analog power supply. connect a 330-nf (or larger) capacitor to avss. 27 avss analog supply negative analog power supply 28 avss-sw analog supply negative analog power supply; low-side switch. connect to avss. 29 refn0 analog input negative external reference input 0 30 refp0 analog input positive external reference input 0 31 refn1/ain7 analog input negative external reference input 1; analog input 7 (ads114s08 only) 32 refp1/ain6 analog input positive external reference input 1; analog input 6 (ads114s08 only) thermal pad ? rhb package only. thermal power pad. connect to avss. advance information 5 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. these are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions . exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 7 specifications 7.1 absolute maximum ratings (1) min max unit power-supply voltage avdd to avss ? 0.3 5.5 v avss to dgnd ? 2.8 0.3 dvdd to dgnd ? 0.3 3.9 iovdd to dgnd ? 0.3 5.5 analog input voltage ainx, gpiox, refpx, refnx, refcom avss ? 0.3 avdd + 0.3 v digital input voltage cs, sclk, din, dout/ drdy, drdy, start, reset, clk dgnd ? 0.3 iovdd + 0.3 v input current continuous, avss-sw, refn0, refout ? 100 100 ma continuous, all other pins except power-supply pins ? 10 10 temperature junction, t j 150 c storage, t stg ? 60 150 (1) jedec document jep155 states that 500-v hbm allows safe manufacturing with a standard esd control process. (2) jedec document jep157 states that 250-v cdm allows safe manufacturing with a standard esd control process. 7.2 esd ratings value unit v (esd) electrostatic discharge human-body model (hbm), per ansi/esda/jedec js-001 (1) 2500 v charged-device model (cdm), per jedec specification jesd22-c101 (2) 1000 advance information 6 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) ain p and ain n denote the positive and negative inputs of the pga. any of the available analog inputs (ainx) can be selected as either ain p or ain n by the input multiplexer. (2) v inmax denotes the maximum differential input voltage, v in , that is expected in the application. |v inmax | can be smaller than v ref / gain. (3) refpx and refnx denote one of the two available external differential reference input pairs. (4) an external clock is not required when the internal oscillator is used. 7.3 recommended operating conditions over operating ambient temperature range (unless otherwise noted) min nom max unit power supply analog power supply avdd to avss 2.7 5.25 v avss to dgnd ? 2.625 0 0.05 avdd to dgnd 1.5 5.25 digital core power supply dvdd to dgnd 2.7 3.6 v digital io power supply iovdd to dgnd dvdd 5.25 v analog inputs (1) v (ainx) absolute input voltage (2) pga bypassed avss ? 0.05 avdd + 0.05 v pga enabled, gain = 1 to 16 avss + 0.15 + |v inmax | (gain ? 1) / 2 avdd ? 0.15 ? |v inmax | (gain ? 1) / 2 pga enabled, gain = 32 to 128 avss + 0.15 + 15.5 |v inmax | avdd ? 0.15 ? 15.5 |v inmax | v in differential input voltage v in = v ainp ? v ainn ? v ref / gain v ref / gain v voltage reference inputs (3) v ref differential reference input voltage v ref = v (refpx) ? v (refnx) 0.5 avdd ? avss v v (refnx) absolute negative reference voltage negative reference buffer disabled avss ? 0.05 v (refpx) ? 0.5 v negative reference buffer enabled avss v (refpx) ? 0.5 v v (refpx) absolute positive reference voltage positive reference buffer disabled v (refnx) + 0.5 avdd + 0.05 v positive reference buffer enabled v (refnx) + 0.5 avdd v external clock source (4) f clk external clock frequency 2 4.096 4.5 mhz duty cycle 40% 50% 60% general-purpose inputs (gpios) input voltage avss ? 0.05 avdd + 0.05 v digital inputs (other than gpios) input voltage dgnd iovdd v temperature range t a operating ambient temperature ? 50 125 c (1) for more information about traditional and new thermal metrics, see the semiconductor and ic package thermal metrics application report. 7.4 thermal information thermal metric (1) ads114s06, ads114s08 unit vqfn (rhb) tqfp (pbs) 32 pins 32 pins r ja junction-to-ambient thermal resistance 45.2 75.5 c/w r jc(top) junction-to-case (top) thermal resistance 28.3 17.1 c/w r jb junction-to-board thermal resistance 15.8 28.5 c/w jt junction-to-top characterization parameter 0.4 0.4 c/w jb junction-to-board characterization parameter 15.7 28.3 c/w r jc(bot) junction-to-case (bottom) thermal resistance 2.3 n/a c/w advance information 7 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 7.5 electrical characteristics minimum and maximum specifications apply from t a = ? 50 c to +125 c; typical specifications are at t a = 25 c; all specifications are at avdd = 2.7 v to 5.25 v, avss = 0 v, dvdd = iovdd = 3.3 v, all gains, internal reference, internal oscillator, all data rates, and global chop disabled (unless otherwise noted) parameter test conditions min typ max unit analog inputs absolute input current pga bypassed, avss + 0.1 v v (ainx) avdd ? 0.1 v 0.5 na pga enabled, all gains, v (ainx)min v (ainx) v (ainx)max ? 2 0.1 2 absolute input current drift pga bypassed, avss + 0.1 v v (ainx) avdd ? 0.1 v 2 pa/ c pga enabled, all gains, v (ainx)min v (ainx) v (ainx)max 2 differential input current pga bypassed, v cm = avdd / 2, ? v ref v in v ref 1 na/v pga enabled, all gains, v cm = avdd / 2, ? v ref / gain v in v ref / gain ? 1 0.02 1 na differential input current drift pga bypassed, v cm = avdd / 2, ? v ref v in v ref 3 pa/ c pga enabled, all gains, v cm = avdd / 2, ? v ref / gain v in v ref / gain 1 pga gain settings 1, 2, 4, 8, 16, 32, 64, 128 startup time enabling the pga in conversion mode 190 s system performance resolution (no missing codes) 16 bits dr data rate 2.5, 5, 10, 16.6, 20, 50, 60, 100, 200, 400, 800, 1000, 2000, 4000 sps inl integral nonlinearity (best fit) pga bypassed, v cm = avdd / 2 1 10 ppm fsr pga enabled, gain = 1 to 8, v cm = avdd / 2 2 15 pga enabled, gain = 16 to 128, v cm = avdd / 2, t a = ? 40 c to +85 c 3 15 v io input offset voltage t a = 25 c, pga bypassed ? 120 20 120 v t a = 25 c, pga enabled, gain = 1 to 8 ? 120 / gain 20 / gain 120 / gain t a = 25 c, pga enabled, gain = 16 to 128 ? 15 2 15 t a = 25 c, pga bypassed, after internal offset calibration on the order of noise pp at the set dr and gain t a = 25 c, pga enabled, gain = 1 to 128, after internal offset calibration on the order of noise pp at the set dr and gain t a = 25 c, pga bypassed, global chop enabled ? 2 0.2 2 t a = 25 c, pga enabled, gain = 1 to 128, global chop enabled ? 2 0.2 2 offset drift t a = ? 40 c to +85 c, pga bypassed ? 75 10 75 nv/ c t a = ? 40 c to +85 c, pga enabled, gain = 1 to 128 ? 100 15 100 pga bypassed ? 75 10 75 pga enabled, gain = 1 to 8 ? 200 15 200 pga enabled, gain = 16 to 128 ? 150 15 150 pga bypassed, global chop enabled ? 10 2 10 pga enabled, gain = 1 to 128, global chop enabled ? 10 2 10 advance information 8 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated electrical characteristics (continued) minimum and maximum specifications apply from t a = ? 50 c to +125 c; typical specifications are at t a = 25 c; all specifications are at avdd = 2.7 v to 5.25 v, avss = 0 v, dvdd = iovdd = 3.3 v, all gains, internal reference, internal oscillator, all data rates, and global chop disabled (unless otherwise noted) parameter test conditions min typ max unit (1) excluding error of voltage reference. (2) see the noise performance section for more information. (3) see the 50-hz and 60-hz line cycle rejection section for more information. system performance (continued) gain error (1) t a = 25 c, pga bypassed 40 120 ppm t a = 25 c, pga enabled, gain = 1 to 32 40 120 t a = 25 c, pga enabled, gain = 64 and 128 40 200 gain drift (1) t a = ? 40 c to +85 c, pga bypassed 0.5 1 ppm/ c t a = ? 40 c to +85 c, pga enabled, gain = 1 to 128 0.5 2 pga bypassed 0.5 1 pga enabled, gain = 1 to 128 1 4 noise (input-referred) (2) pga enabled, gain = 128, dr = 2.5 sps, sinc 3 filter 19 nv rms nmrr normal-mode rejection ratio (3) f in = 50 hz or 60 hz ( 1 hz), dr = 10 sps, sinc 3 filter 88 db f in = 50 hz or 60 hz ( 1 hz), dr = 10 sps, sinc 3 filter, external f clk = 4.096 mhz 102 f in = 50 hz or 60 hz ( 1 hz), dr = 20 sps, low-latency filter 79 f in = 50 hz or 60 hz ( 1 hz), dr = 20 sps, low-latency filter, external f clk = 4.096 mhz 95 f in = 50 hz ( 1 hz), dr = 50 sps, sinc 3 filter 87 f in = 50 hz ( 1 hz), dr = 50 sps, sinc 3 filter, external f clk = 4.096 mhz 101 f in = 60 hz ( 1 hz), dr = 60 sps, sinc 3 filter 89 f in = 60 hz ( 1 hz), dr = 60 sps, sinc 3 filter, external f clk = 4.096 mhz 105 cmrr common-mode rejection ratio at dc 110 120 db f cm = 50 hz or 60 hz ( 1 hz), dr = 2.5 sps to 10 sps, sinc 3 filter 120 130 f cm = 50 hz or 60 hz ( 1 hz), dr = 2.5 sps, 5 sps, 10 sps, 20 sps, low-latency filter 115 125 psrr power-supply rejection ratio avdd at dc 90 105 db avdd at 50 hz or 60 hz 100 115 dvdd at dc 100 115 advance information 9 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated electrical characteristics (continued) minimum and maximum specifications apply from t a = ? 50 c to +125 c; typical specifications are at t a = 25 c; all specifications are at avdd = 2.7 v to 5.25 v, avss = 0 v, dvdd = iovdd = 3.3 v, all gains, internal reference, internal oscillator, all data rates, and global chop disabled (unless otherwise noted) parameter test conditions min typ max unit (4) the idac current does not change by more than 0.1% from the nominal value when staying within the specified compliance voltage. voltage reference inputs absolute input current reference buffers disabled, external v ref = 2.5 v, refp1/refn1 inputs -6 4 6 a/v reference buffers enabled, external v ref = 2.5 v, refp1/refn1 inputs ? 15 5 15 na internal voltage reference v ref output voltage 2.5 v accuracy t a = 25 c ? 0.05% 0.01% 0.05% temperature drift t a = ? 40 c to +85 c 2.5 8 ppm/ c t a = ? 50 c to +125 c 3 10 output current avdd = 2.7 v to 3.3 v, sink and source ? 5 5 ma avdd = 3.3 v to 5.25 v, sink and source ? 10 10 short-circuit current limit sink and source 70 100 ma psrr power-supply rejection ratio avdd at dc 85 db load regulation avdd = 2.7 v to 3.3 v, load current = ? 5 ma to 5 ma 8 v/ma avdd = 3.3 v to 5.25 v, load current = ? 10 ma to 10 ma 8 startup time 1- f capacitor on refout, 0.001% settling 5.9 ms capacitive load stability capacitor on refout 1 47 f reference noise f = 0.1 hz to 10 hz, 1- f capacitor on refout 17.5 v pp internal oscillator f clk frequency 4.096 mhz accuracy ? 1.5% 1.5% excitation current sources (idacs) current settings 10, 50, 100, 250, 500, 750, 1000, 1500, 2000 a compliance voltage (4) 10 a to 750 a, 0.1% deviation avss avdd ? 0.4 v 1 ma to 2 ma, 0.1% deviation avss avdd ? 0.6 accuracy (each idac) t a = 25 c, 10 a to 100 a ? 5% 0.7% 5% t a = 25 c, 250 a to 2 ma ? 3% 0.5% 3% current mismatch between idacs t a = 25 c, 10 a to 100 a 0.15% 0.8% t a = 25 c, 250 a to 750 a 0.10% 0.6% t a = 25 c, 1 ma to 2 ma 0.07% 0.4% temperature drift (each idac) 10 a to 750 a 20 120 ppm/ c 1 ma to 2 ma 10 80 temperature drift matching between idacs 10 a to 100 a 3 25 ppm/ c 250 a to 2 ma 2 15 startup time with internal reference already settled. from end of wreg command to current flowing out of pin. 22 s advance information 10 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated electrical characteristics (continued) minimum and maximum specifications apply from t a = ? 50 c to +125 c; typical specifications are at t a = 25 c; all specifications are at avdd = 2.7 v to 5.25 v, avss = 0 v, dvdd = iovdd = 3.3 v, all gains, internal reference, internal oscillator, all data rates, and global chop disabled (unless otherwise noted) parameter test conditions min typ max unit bias voltage v bias output voltage settings (avdd + avss) / 2, (avdd + avss) / 12 v output impedance 350 startup time combined capacitive load on all selected analog inputs c load = 1 f, 0.1% settling 2.8 ms burnout current sources (bocs) current settings 0.2, 1, 10 a accuracy 0.2 a, sinking or sourcing 8% 1 a, sinking or sourcing 4% 10 a, sinking or sourcing 2% pga rail detection positive rail threshold referred to the output of the pga avdd ? 0.15 v negative rail threshold referred to the output of the pga avss + 0.15 v reference detection threshold 1 0.3 v threshold 2 1/3 (avdd ? avss) v threshold 2 accuracy ? 3% 1% 3% pull-together resistance 10 m supply voltage monitors accuracy (avdd ? avss) / 4 monitor 1% dvdd / 4 monitor 1% temperature sensor output voltage t a = 25 c 129 mv temperature coefficient 403 v/ c low-side power switch r on on-resistance 1 3 current through switch 75 ma general-purpose input/outputs (gpios) v il logic input level, low avss ? 0.05 0.3 avdd v v ih logic input level, high 0.7 avdd avdd + 0.05 v v ol logic output level, low i ol = 1 ma avss 0.2 avdd v v oh logic output level, high i oh = 1 ma 0.8 avdd avdd v digital input/outputs v il logic input level, low dgnd 0.3 iovdd v v ih logic input level, high 0.7 iovdd iovdd v v ol logic output level, low i ol = 1 ma dgnd 0.2 iovdd v v oh logic output level, high i oh = 1 ma 0.8 iovdd iovdd v input current dgnd v digital input iovdd ? 1 1 a advance information 11 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated electrical characteristics (continued) minimum and maximum specifications apply from t a = ? 50 c to +125 c; typical specifications are at t a = 25 c; all specifications are at avdd = 2.7 v to 5.25 v, avss = 0 v, dvdd = iovdd = 3.3 v, all gains, internal reference, internal oscillator, all data rates, and global chop disabled (unless otherwise noted) parameter test conditions min typ max unit analog supply current (avdd = 3.3 v, external reference, internal reference disabled, reference buffers disabled, idacs disabled, vbias disabled, flags disabled, internal oscillator, all data rates, v in = 0 v) i avdd analog supply current power-down mode 0.1 1.5 a standby mode, pga bypassed 70 conversion mode, pga bypassed 85 conversion mode, pga enabled, gain = 1, 2 120 135 conversion mode, pga enabled, gain = 4, 8 140 155 conversion mode, pga enabled, gain = 16, 32 165 180 conversion mode, pga enabled, gain = 64 200 conversion mode, pga enabled, gain = 128 250 additional analog supply currents per function (avdd = 3.3 v) i avdd analog supply current internal 2.5-v reference, no external load 185 280 a positive reference buffer 35 60 negative reference buffer 25 40 vbias buffer, no external load 10 idac overhead, 10 a to 250 a 20 35 idac overhead, 500 a to 750 a 30 idac overhead, 1 ma 40 idac overhead, 1.5 ma 50 idac overhead, 2 ma 65 pga rail detection and reference detection circuit 10 digital supply current (dvdd = iovdd = 3.3 v, all data rates, spi not active) i dvdd + i iovdd digital supply current power-down mode, internal oscillator 0.1 a standby mode, internal oscillator 185 conversion mode, internal oscillator 225 300 conversion mode, external f clk = 4.096 mhz 195 power dissipation (avdd = dvdd = iovdd = 3.3 v, internal reference enabled, reference buffers disabled, idacs disabled, vbias disabled, flags disabled, internal oscillator, all data rates, v in = 0 v, spi not active) p d power dissipation conversion mode, pga enabled, gain = 1 1.75 mw advance information 12 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) t clk = 1 / f clk . (2) only applicable when reading data without the rdata command. all commands can be send without any sclk to drdy signal timing restrictions. 7.6 timing characteristics over operating ambient temperature range, dvdd = 2.7 v to 3.6 v, iovdd = dvdd to 5.25 v, and dout/ drdy load = 20 pf || 100 k to dgnd (unless otherwise noted) min max unit (1) serial interface t d(cssc) delay time, first sclk rising edge after cs falling edge 20 ns t d(sccs) delay time, cs rising edge after final sclk falling edge 20 ns t w(csh) pulse duration, cs high 30 ns t c(sc) sclk period 100 ns t w(sch) pulse duration, sclk high 40 ns t w(scl) pulse duration, sclk low 40 ns t su(di) setup time, din valid before sclk falling edge 15 ns t h(di) hold time, din valid after sclk falling edge 20 ns t d(cmd) delay time, between bytes or commands 0 ns reset pin t w(rsl) pulse duration, reset low 4 t clk t d(rssc) delay time, first sclk rising edge after reset rising edge (or 7th sclk falling edge of reset command) 4096 t clk start/sync pin t w(sth) pulse duration, start/sync high 4 t clk t w(stl) pulse duration, start/sync low 4 t clk t su(stdr) setup time, start/sync falling edge (or 7th sclk falling edge of stop command) before drdy falling edge to stop further conversions (continuous conversion mode) 32 t clk reading conversion data without rdata command t h(scdr) hold time, sclk low before drdy falling edge (2) 28 t clk t d(drsc) delay time, sclk rising edge after drdy falling edge (2) 4 t clk (1) t clk = 1 / f clk (2) the spi interface resets when an entire byte is not sent within the specified timeout time. 7.7 switching characteristics over operating ambient temperature range, dvdd = 2.7 v to 3.6 v, iovdd = dvdd to 5.25 v, and dout/ drdy load = 20 pf || 100 k to dgnd (unless otherwise noted) parameter test conditions min typ max unit (1) t p(csdo) propagation delay time, cs falling edge to dout driven 0 25 ns t p(scdo) propagation delay time, sclk rising edge to valid new dout 3 30 ns t p(csdoz) propagation delay time, cs rising edge to dout high impedance 0 25 ns t p(stdr) propagation delay time, start/sync rising edge (or first sclk rising edge of any command or data read) to drdy rising edge 2 t clk t w(drh) pulse duration, drdy high 24 t clk t p(gpio) propagation delay time, last sclk falling edge of wreg command to gpiox output valid 3 100 ns spi timeout per 8 bit (2) 2 15 t clk advance information 13 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated note: single-byte communication is shown. actual communication can be multiple bytes. figure 1. serial interface timing requirements note: single-byte communication is shown. actual communication can be multiple bytes. figure 2. serial interface switching characteristics figure 3. reset pin and reset command timing requirements figure 4. start/sync pin timing requirements t w(stl) start/sync drdy t p(stdr) t su(stdr) t w(drh) t w(sth) t p(stdr) sclk din reset command reset new command t w(rsl) t d(rssc) hi-z hi-z cs sclk dout/drdy t p(csdo) t p(scdo) t p(csdoz) cs sclk din t t d(cssc) t t t c(sc) t t t d(sccs) t t w(csh) t w(sch) t w(scl) t su(di) t h(di) advance information 14 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated figure 5. start command timing requirements figure 6. read data direct (without an rdata command) timing requirements figure 7. gpio switching characteristics sclk din wreg gpio0 t p(gpio) 01h 01h 01h wreg gpiodat write two registers gpio0 set as output gpio0 set high gpio0 enabled data 1 sclk cs drdy dout/drdy data 2 t h(scdr) t d(drsc) sclk din start command drdy t p(stdr) stop command t su(stdr) t p(stdr) advance information 15 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 7.8 typical characteristics at t a = 25 c, avdd = 3.3 v, avss = 0 v, dvdd = iovdd = 3.3 v, using internal v ref = 2.5 v, internal 4.096-mhz oscillator, and pga enabled (unless otherwise noted) all unselected analog inputs at v ainx = 1.65 v figure 8. absolute input current vs temperature v in = 0 v figure 9. absolute input current vs v cm v in = 2.5 v, v cm = 1.65 v figure 10. differential input current vs temperature v cm = 1.65 v figure 11. differential input current vs v in pga bypassed, gain = 1 figure 12. inl vs v in gain = 1 figure 13. inl vs v in temperature ( q c) input current (na) -60 -40 -20 0 20 40 60 80 100 120 140 -0.4 -0.2 0 0.2 0.4 0.6 0.8 20 sps 4000 sps v cm (v) input current (na) 0 0.5 1 1.5 2 2.5 3 3.5 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 20 sps 4000 sps advance information v in (% of fsr) inl (ppm of fsr) -100 -80 -60 -40 -20 0 20 40 60 80 100 -3 -2 -1 0 1 2 3 v in (% of fsr) inl (ppm of fsr) -100 -80 -60 -40 -20 0 20 40 60 80 100 -3 -2 -1 0 1 2 3 temperature ( q c) input current (na) -60 -40 -20 0 20 40 60 80 100 120 140 0 0.1 0.2 0.3 0.4 0.5 20 sps 4000 sps v in (v) differential input current (na) -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 0 0.1 0.2 0.3 0.4 20 sps 4000 sps 16 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated typical characteristics (continued) at t a = 25 c, avdd = 3.3 v, avss = 0 v, dvdd = iovdd = 3.3 v, using internal v ref = 2.5 v, internal 4.096-mhz oscillator, and pga enabled (unless otherwise noted) figure 14. inl vs temperature figure 15. offset voltage vs temperature figure 16. gain error vs temperature 512 samples figure 17. internal reference voltage histogram figure 18. internal reference voltage vs temperature figure 19. internal reference voltage vs avdd temperature (c) reference voltage (v) -60 -40 -20 0 20 40 60 80 100 120 140 2.4984 2.4988 2.4992 2.4996 2.5 2.5004 2.5008 avdd voltage (v) reference voltage (v) 2.5 3 3.5 4 4.5 5 5.5 2.4997 2.4998 2.4999 2.5 2.5001 2.5002 internal reference voltage (v) number of occurances 0 25 50 75 100 125 150 175 2.49975 2.4998 2.49985 2.4999 2.49995 2.5 2.50005 2.5001 2.50015 2.5002 2.50025 temperature ( q c) gain error (ppm) -60 -40 -20 0 20 40 60 80 100 120 140 -250 -200 -150 -100 -50 0 50 100 gain = 1 gain = 2 gain = 4 gain = 8 gain = 16 gain = 32 gain = 64 gain = 128 temperature ( q c) inl (ppm of fsr) -60 -40 -20 0 20 40 60 80 100 120 140 0 2 4 6 8 10 gain = 1 gain = 2 gain = 4 gain = 8 gain = 16 gain = 32 gain = 64 gain = 128 temperature ( q c) offset voltage ( p v) -60 -40 -20 0 20 40 60 80 100 120 140 0 2 4 6 8 10 12 14 16 gain = 1 gain = 2 gain = 4 gain = 8 gain = 16 gain = 32 gain = 64 gain = 128 advance information 17 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated typical characteristics (continued) at t a = 25 c, avdd = 3.3 v, avss = 0 v, dvdd = iovdd = 3.3 v, using internal v ref = 2.5 v, internal 4.096-mhz oscillator, and pga enabled (unless otherwise noted) figure 20. oscillator frequency histogram figure 21. oscillator frequency vs temperature figure 22. idac accuracy vs compliance voltage figure 23. idac accuracy vs compliance voltage idac output voltage = 1.65 v figure 24. idac accuracy vs temperature figure 25. idac matching vs temperature idac output voltage (v) idac error (%) 2.5 2.6 2.7 2.8 2.9 3 3.1 3.2 -5 -4 -3 -2 -1 0 10 a 50 a 100 a 250 a 500 a 750 a 1 ma 1.5 ma 2 ma internal oscillator frequency (mhz) number of occurances 0 50 100 150 200 250 4.09 4.092 4.094 4.096 4.098 4.1 4.102 4.104 4.106 temperature (c) frequency (mhz) -60 -40 -20 0 20 40 60 80 100 120 140 4.04 4.06 4.08 4.1 4.12 4.14 advance information temperature ( q c) idac error (%) -60 -40 -20 0 20 40 60 80 100 120 140 -3 -2 -1 0 1 2 3 10 a 50 a 100 a 250 a 500 a 750 a 1 ma 1.5 ma 2 ma temperature ( q c) idac mismatch error (%) -60 -40 -20 0 20 40 60 80 100 120 140 0 0.05 0.1 0.15 0.2 0.25 0.3 10 a 50 a 100 a 250 a 500 a 750 a 1 ma 1.5 ma 2 ma idac output voltage (v) idac error (%) 0 0.5 1 1.5 2 2.5 3 3.5 -50 -40 -30 -20 -10 0 10 a 50 a 100 a 250 a 500 a 750 a 1 ma 1.5 ma 2 ma 18 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated typical characteristics (continued) at t a = 25 c, avdd = 3.3 v, avss = 0 v, dvdd = iovdd = 3.3 v, using internal v ref = 2.5 v, internal 4.096-mhz oscillator, and pga enabled (unless otherwise noted) figure 26. temperature sensor voltage vs temperature figure 27. low-side switch r on vs temperature level 0 = 300 mv figure 28. reference threshold voltage, level 0 level 1 = 1/3 (avdd ? avss) figure 29. reference threshold voltage, level 1 figure 30. vbias voltage [(avdd ? avss) / 2] vs temperature figure 31. vbias voltage [(avdd - avss) / 12] vs temperature temperature (c) (avdd-avss)/2 ratio -60 -40 -20 0 20 40 60 80 100 120 140 0.498 0.4985 0.499 0.4995 0.5 0.5005 0.501 avdd = 2.7 v avdd = 5.5 v temperature (c) (avdd-avss)/12 ratio -60 -40 -20 0 20 40 60 80 100 120 140 0.08 0.081 0.082 0.083 0.084 0.085 0.086 avdd = 2.7 v avdd = 5.5 v temperature (c) voltage (v) -60 -40 -20 0 20 40 60 80 100 120 140 0.286 0.288 0.29 0.292 0.294 0.296 0.298 0.3 avdd = 2.7 v avdd = 5.5 v temperature (c) 1/3 ? (avdd-avss) ratio -60 -40 -20 0 20 40 60 80 100 120 140 0.333 0.3332 0.3334 0.3336 0.3338 0.334 0.3342 0.3344 0.3346 0.3348 0.335 avdd = 2.7 v avdd = 5.5 v temperature (c) resistance ( : ) -60 -40 -20 0 20 40 60 80 100 120 140 0.6 0.8 1 1.2 1.4 1.6 1.8 avdd = 2.7 v avdd = 3.3 v avdd = 5.5 v advance information temperature (c) temperature sensor voltage (mv) -60 -40 -20 0 20 40 60 80 100 120 140 80 100 120 140 160 180 19 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated typical characteristics (continued) at t a = 25 c, avdd = 3.3 v, avss = 0 v, dvdd = iovdd = 3.3 v, using internal v ref = 2.5 v, internal 4.096-mhz oscillator, and pga enabled (unless otherwise noted) conversion mode, external v ref figure 32. analog supply current vs avdd conversion mode, external v ref figure 33. analog supply current vs temperature power-down mode figure 34. analog supply current vs temperature conversion mode figure 35. digital supply current vs dvdd power-down mode figure 36. digital supply current vs temperature dvdd voltage (v) dvdd current ( p a) 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 160 180 200 220 240 260 avdd voltage (v) avdd current ( p a) 2.5 3 3.5 4 4.5 5 5.5 50 100 150 200 250 300 350 400 pga bypassed gain = 1 gain = 4 gain = 16 gain = 64 gain = 128 temperature ( q c) avdd current ( p a) -60 -40 -20 0 20 40 60 80 100 120 140 50 100 150 200 250 300 350 400 pga bypassed gain = 1 gain = 4 gain = 16 gain = 64 gain = 128 advance information temperature (c) dvdd current ( p a) -60 -40 -20 0 20 40 60 80 100 120 140 0 1 2 3 4 5 temperature (c) avdd current ( p a) -60 -40 -20 0 20 40 60 80 100 120 140 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 20 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 8 parameter measurement information 8.1 noise performance delta-sigma ( ) analog-to-digital converters (adcs) are based on the principle of oversampling. the input signal of a adc is sampled at a high frequency (modulator frequency) and subsequently filtered and decimated in the digital domain to yield a conversion result at the respective output data rate. the ratio between modulator frequency and output data rate is called the oversampling ratio (osr). by increasing the osr, and thus reducing the output data rate, the noise performance of the adc can be optimized. in other words, the input-referred noise drops when reducing the output data rate because more samples of the internal modulator are averaged to yield one conversion result. increasing the gain also reduces the input-referred noise, which is particularly useful when measuring low-level signals. table 1 to table 4 summarize the device noise performance. table 1 and table 2 show the adc measurement noise using the sinc 3 digital filter at different data rates and different pga settings, and table 3 and table 4 show the adc measurement noise using the low-latency digital filter. data are representative of typical noise performance at t a = 25 c using the internal 2.5-v reference. data shown are based on 512 consecutive samples from a single device with inputs internally shorted. table 1 and table 3 list the input-referred root mean square noise in units of v rms for the conditions shown. note that peak-to-peak ( v pp ) values are shown in parentheses. table 2 and table 4 list the corresponding data in effective resolution calculated from v rms values using equation 1 . noise-free resolution is calculated from v pp values using equation 2 . the input-referred noise ( table 1 and table 3 ) only changes marginally when using an external low-noise reference, such as the ref5025 . to calculate effective resolution and noise-free resolution when using a reference voltage other than 2.5 v, use equation 1 and equation 2 : effective resolution = ln[(2 v ref / gain) / v rms-noise ] / ln(2) (1) noise-free resolution= ln[(2 v ref / gain) / v pp-noise ] / ln(2) (2) table 5 to table 8 repeat the measurements of table 1 to table 4 but use the global chop feature of the device. the global chop feature averages two measurement of the adc with the inputs swapped. this feature significantly reduces the input offset of the device, and reduces noise in the measurement. noise performance with the pga bypassed are identical to the noise performance of the device with gain = 1 in table 1 to table 8 . table 1. noise in v rms ( v pp ) with sinc 3 filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop disabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 10 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 16.6 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 20 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 50 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 60 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 100 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 200 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.90) 400 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.5) 0.60 (1.3) 800 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (2.2) 0.60 (2.0) 1000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.5) 1.2 (2.4) 0.60 (2.2) 2000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (4.0) 1.2 (3.5) 0.60 (2.8) 4000 76.3 (95) 38.1 (45) 19.1 (24) 9.5 (13) 4.8 (7.1) 2.4 (5.2) 1.2 (5.0) 0.80 (4.9) advance information 21 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated table 2. effective resolution from rms noise (noise-free resolution from peak-to-peak noise) with sinc 3 filter at avdd = 3.3 v, avss = 0 v, pga enabled, global chop disabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 10 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16.6 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 20 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 50 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 60 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 100 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 200 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.3) 400 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.7) 16 (14.9) 800 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.1) 16 (14.3) 1000 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.0) 16 (14.1) 2000 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.3) 16 (14.4) 16 (13.8) 4000 16 (15.7) 16 (15.7) 16 (15.7) 16 (15.6) 16 (15.4) 16 (14.9) 16 (13.9) 16 (13.0) table 3. noise in v rms ( v pp ) with low-latency filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop disabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 10 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 16.6 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 20 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 50 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 60 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.90) 100 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.9) 0.60 (1.3) 200 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (2.6) 0.60 (1.7) 400 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.8) 1.2 (2.9) 0.60 (2.3) 800 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (4.0) 1.2 (3.8) 0.60 (3.2) 1000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (5.1) 1.2 (4.3) 0.60 (3.8) 2000 76.3 (83) 38.1 (80) 19.1 (32) 9.5 (17) 4.8 (11) 2.4 (6.7) 1.2 (6.6) 1.0 (6.5) 4000 103 (629) 38.1 (404) 24 (160) 12 (70) 6.4 (39) 3.3 (21) 3.1 (21) 2.6 (20) advance information 22 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated table 4. effective resolution from rms noise (noise-free resolution from peak-to-peak noise) with low-latency filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop disabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 10 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16.6 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 20 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 50 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.5) 60 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.4) 100 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (14.9) 16 (14.9) 200 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.3) 16 (14.5) 400 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.8) 16 (14.7) 16 (14.0) 800 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.2) 16 (14.3) 16 (13.6) 1000 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.8) 16 (14.9) 16 (14.2) 16 (13.3) 2000 16 (15.9) 16 (14.9) 16 (15.3) 16 (15.2) 16 (14.8) 16 (14.5) 16 (13.5) 15.2 (12.6) 4000 16 (13.0) 16 (12.6) 15.7 (12.9) 16 (13.1) 15.6 (13.0) 15.5 (12.9) 14.4 (11.9) 13.6 (10.9) (1) the actual data conversion period changes with the sinc 3 filter and global chop mode enabled; see table 19 for details. table 5. noise in v rms ( v pp ) with sinc 3 filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop enabled, and internal 2.5-v reference data rate (sps) (1) gain 1 2 4 8 16 32 64 128 2.5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 10 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 16.6 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 20 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 50 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 60 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 100 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 200 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.75) 400 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.90) 800 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.4) 0.60 (1.3) 1000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.6) 0.60 (1.5) 2000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.5) 1.2 (2.1) 0.60 (2.1) 4000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (5.0) 2.4 (4.0) 1.2 (3.3) 0.60 (3.2) advance information 23 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) the actual data conversion period changes with the sinc 3 filter and global chop mode enabled; see table 19 for details. table 6. effective resolution from rms noise (noise-free resolution from peak-to-peak noise) with sinc 3 filter at avdd = 3.3 v, avss = 0 v, pga enabled, global chop enabled, and internal 2.5-v reference data rate (sps) (1) gain 1 2 4 8 16 32 64 128 2.5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 10 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16.6 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 20 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 50 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 60 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 100 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 200 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.7) 400 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.4) 800 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.7) 16 (14.9) 1000 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.6) 16 (14.7) 2000 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.9) 16 (15.2) 16 (14.2) 4000 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.9) 16 (15.3) 16 (14.5) 16 (13.6) table 7. noise in v rms ( v pp ) with low-latency filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop enabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 5 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 10 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 16.6 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 20 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 50 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.60) 60 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.67) 100 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.2) 0.60 (0.80) 200 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.3) 0.60 (1.0) 400 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (1.8) 0.60 (1.7) 800 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.4) 1.2 (2.5) 0.60 (2.3) 1000 76.3 (76.3) 38.1 (38.1) 19.1 (19.1) 9.5 (9.5) 4.8 (4.8) 2.4 (2.8) 1.2 (2.4) 0.60 (2.5) 2000 76.3 (76.3) 38.1 (48) 19.1 (23) 9.5 (13) 4.8 (7.0) 2.4 (5.6) 1.2 (5.2) 0.7 (3.9) 4000 76.3 (275) 38.1 (190) 19.1 (100) 9.5 (55) 4.8 (28) 2.4 (15) 1.2 (13) 2.2 (12) advance information 24 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated table 8. effective resolution from rms noise (noise-free resolution from peak-to-peak noise) with low-latency filter, at avdd = 3.3 v, avss = 0 v, pga enabled, global chop enabled, and internal 2.5-v reference data rate (sps) gain 1 2 4 8 16 32 64 128 2.5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 5 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 10 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16.6 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 20 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 50 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 60 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.8) 100 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.6) 200 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.9) 16 (15.2) 400 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.4) 16 (14.5) 800 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (14.9) 16 (14.0) 1000 16 (16) 16 (16) 16 (16) 16 (16) 16 (16) 16 (15.8) 16 (15.0) 16 (13.9) 2000 16 (16) 16 (15.7) 16 (15.7) 16 (15.6) 16 (15.4) 16 (14.8) 16 (13.9) 15.9 (13.3) 4000 16 (14.1) 16 (13.7) 16 (13.6) 16 (13.5) 16 (13.4) 16 (13.4) 15.0 (12.7) 14.1 (11.5) advance information 25 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9 detailed description 9.1 overview the ads114s06 and ads114s08 are precision 16-bit, delta-sigma ( ) adcs with an integrated analog front end (afe) to simplify precision sensor connections. the adc provides output data rates from 2.5 sps to 4000 sps for flexibility in resolution and data rates over a wide range of applications. the low-noise and low-drift architecture make these devices suitable for precise measurement of low-voltage sensors, such as load cells and temperature sensors. the ads114s0x incorporate several features that simplify precision sensor measurements. key integrated features include: ? low-noise, cmos pga with integrated signal fault detection ? low-drift, 2.5-v voltage reference ? two sets of buffered external reference inputs with reference voltage level detection ? dual, matched, sensor-excitation current sources (idacs) ? internal 4.096-mhz oscillator ? temperature sensor ? four general-purpose input/output pins (gpios) ? a low-resistance switch (when connected to avss) can be used to disconnect bridge sensors to reduce current consumption as described in the functional block diagram section, these devices provide 13 (ads114s08) or 7 (ads114s06) analog inputs that are configurable as either single-ended inputs, differential inputs, or any combination of the two. many of the analog inputs have additional features as programmed by the user. the analog inputs can be programmed to enable the following extended features: ? two sensor excitation current sources: all analog input pins (and refp1 and refn1 on the ads114s06) ? sensor biasing voltage (vbias): pins ain0, ain1, ain2, ain3, ain4, ain5, aincom ? four gpio pins: ain8, ain9, ain10, ain11 (ads114s08 only, the ads114s06 has dedicated gpios) ? sensor burn-out current sources: analog input pins selected for adc input following the input multiplexer (mux), the adc features a high input-impedance, low-noise, programmable gain amplifier (pga), eliminating the need for an external amplifier. the pga gain is programmable from 1 to 128 in binary steps. the pga can be bypassed to allow the input range to extend 50 mv below ground or above supply. the pga has output voltage monitors to verify the integrity of the conversion result. an inherently stable delta-sigma modulator measures the ratio of the input voltage to the reference voltage to provide the adc result. the adc operates with the internal 2.5-v reference, or with up to two external reference inputs. the external reference inputs can be continuously monitored for low (or missing) voltage. the refout pin provides the buffered 2.5-v internal voltage reference output that can be used to bias external circuitry. the digital filter provides two filter modes, sinc 3 and low-latency, allowing optimization of settling time and line- cycle rejection. the third-order sinc filter offers simultaneous 50-hz and 60-hz line-cycle rejection at data rates of 2.5 sps, 5 sps, and 10 sps, 50-hz rejection at data rates of 16.6 sps and 50 sps, and 60-hz rejection at data rates of 20 sps and 60 sps. the low-latency filter provides settled data with 50-hz and 60-hz line-cycle rejection at data rates of 2.5 sps, 5 sps, 10 sps, and 20 sps, 50-hz rejection at data rates of 16.6 sps and 50 sps, and 60-hz rejection at a data rate of 60 sps. two programmable excitation current sources provide bias to resistive sensors [such as resistance temperature detectors (rtds) or thermistors]. the adc integrates several system monitors for read back, such as temperature sensor and supply monitors. four gpio pins are available as either dedicated pins (ads114s06) or combined with analog input pins (ads114s08). the ads114s0x system clock is either provided by the internal low-drift, 4.096-mhz oscillator or an external clock source on the clk input. advance information 26 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated overview (continued) the spi-compatible serial interface is used to read the conversion data and also to configure and control the adc. the serial interface consists of four signals: cs, sclk, din, and dout/ drdy. the conversion data are provided with an optional crc code for improved data integrity. the dual function dout/ drdy output indicates when conversion data are ready and also provides the data output. the serial interface can be implemented with as little as three connections by tying cs low. start adc conversions with either the start/sync pin or with commands. the adc can be programmed for a continuous conversion mode or to perform single-shot conversions. the avdd analog supply operates with bipolar supplies from 1.5 v to 2.625 v or with a unipolar supply from 2.7 v to 5.25 v. for unipolar-supply operation, use the vbias voltage to bias isolated (floating) sensors. the digital supplies operate with unipolar supplies only. the dvdd digital power supply operates from 2.7 v to 3.6 v and the iovdd supply operates from dvdd to 5.25 v. 9.2 functional block diagram pga input mux serial interface and control cs dout/drdy sclk drdy start/sync 4.096-mhz oscillator clk refout reference detection pga rail detection aincom ain0 ain1 / gpio1 power supplies temperature sensor ads114s06 ads114s08 dvdd dgnd ain2 ain3 ain4 ain5 / refp1 / refn1 / gpio0 excitation current sources reset din refp0 refcom / gpio3 / gpio2 avss vbias avdd reference buffers reference mux 2.5-v reference refn0 ads114s08 only burnout detect burnout detect 16-bit ? adc configurable digital filter avss-sw dvdd iovdd system-, self- calibration ain9 ain6 ain7 ain8 ain11 ain10 copyright ? 2017, texas instruments incorporated advance information 27 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3 feature description 9.3.1 multiplexer the ads114s0x contains a flexible input multiplexer; see figure 37 . select any of the six (ads114s06) or 12 (ads114s08) analog inputs as the positive or negative input for the pga using the mux_p[3:0] and mux_n[3:0] bits in the input multiplexer register (02h). in addition, aincom can be selected as the positive or negative pga input. aincom is treated as a regular analog input, as is ainx. use aincom in single-ended measurement applications as the common input for the other analog inputs. the multiplexer also routes the excitation current sources to drive resistive sensors (bridges, rtds, and thermistors) and can provide bias voltages for unbiased sensors (unbiased thermocouples for example) to analog input pins. the ads114s0x also contain a set of system monitor functions measured through the multiplexer. the inputs can be shorted together at mid-supply [(avdd + avss) / 2] to measure and calibrate the input offset of the analog front-end and the adc. the system monitor also includes a temperature sensor that provides a measurement of the device temperature. the system monitor can also measure the analog and digital supplies, measuring [(avdd ? avss) / 4] for the analog supply or dvdd / 4 for the digital supply. finally, the system monitor contains a set of burn-out current sources that pull the inputs to either supply if the sensor has burned out and has a high impedance so that the adc measures a full-scale reading. the multiplexer implements a break-before-make circuit. when changing the multiplexer channels using the mux_p[3:0] and mux_n[3:0] bits, the device first disconnects the pga inputs from the analog inputs and connects them to mid-supply for 2 t clk . in the next step, the pga inputs connect to the selected new analog input channels. this break-before-make behavior ensures the adc always starts from a known state and that the analog inputs are not momentarily shorted together. electrostatic discharge (esd) diodes to avdd and avss protect the inputs. to prevent the esd diodes from turning on, the absolute voltage on any input must stay within the range provided by equation 3 : avss ? 0.3 v < v (ainx) < avdd + 0.3 v (3) external schottky clamp diodes or series resistors may be required to limit the input current to safe values (see the absolute maximum ratings table). overdriving an unselected input on the device can affect conversions taking place on other input pins. advance information 28 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated feature description (continued) (1) ain p and ain n are connected together to (avdd + avss) / 2 for offset measurement. (2) measurement for the analog supply equivalent to (avdd ? avss) / 4. (3) measurement for the analog supply equivalent to dvdd / 4. figure 37. analog input multiplexer ain0 avdd avdd idac1 idac2 avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avss avdd avdd avdd (avdd avss) ? (5 / 8) '9''? (4 / 12) avdd avss temperature diode vbias vbias vbias vbias vbias vbias pga burn-out current source burn-out current source to adc ain p ain n ain1 ain2 ain3 ain4 ain5 ain6 ain7 ain8 ain9 ain10 ain11 vbias avss avdd avss avdd aincom ads114s08 only (avdd avss) ? (3 / 8) '9''? (1 / 12) (2) (3) (1) (avdd + avss) / 2 copyright ? 2017, texas instruments incorporated advance information 29 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated feature description (continued) 9.3.2 low-noise programmable gain amplifier the ads114s06 and ads114s08 feature a low-drift, low-noise, high input impedance programmable gain amplifier (pga). figure 38 shows a simplified diagram of the pga. the pga consists of two chopper-stabilized amplifiers (a1 and a2) and a resistor feedback network that sets the gain of the pga. the pga input is equipped with an electromagnetic interference (emi) filter and an antialiasing filter on the output. figure 38. simplified pga diagram the pga can be set to gains of 1, 2, 4, 8, 16, 32, 64, or 128 using the gain[2:0] bits in the gain setting register (03h). gain is changed inside the device using a variable resistor, r g . the differential full-scale input voltage range (fsr) of the pga is defined by the gain setting and the reference voltage used, as shown in equation 4 : fsr = v ref / gain (4) table 9 shows the corresponding full-scale ranges when using the internal 2.5-v reference. table 9. pga full-scale range gain setting fsr 1 2.5 v 2 1.25 v 4 0.625 v 8 0.313 v 16 0.156 v 32 0.078 v 64 0.039 v 128 0.020 v the pga must be enabled with the pga_en[1:0] bits of the gain setting register (03h). setting these bits to 00 powers down and bypasses the pga. a setting of 01 enables the pga. the 10 and 11 settings are reserved and must not be written to the device. with the pga enabled, gains 64 and 128 are established in the digital domain. when the device is set to 64 or 128, the pga is set to a gain of 32, and additional gain is established with digital scaling. the input-referred noise does still improve compared to the gain = 32 setting because the pga is biased with a higher supply current to reduce noise. advance information 250 + + 250 16 pf 16 pf 320 pf a1 a2 2.5 k 2.5 k adc ain p ain n r g r f r f 30 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.2.1 pga input-voltage requirements as with many amplifiers, the pga has an absolute input voltage range requirement that cannot be exceeded. the maximum and minimum absolute input voltages are limited by the voltage swing capability of the pga output. the specified minimum and maximum absolute input voltages (v ainp and v ainn ) depend on the pga gain, the maximum differential input voltage (v inmax ), and the tolerance of the analog power-supply voltages (avdd and avss). use the maximum voltage expected in the application for v inmax . the absolute positive and negative input voltages must be within the specified range, as shown in equation 5 : avss + 0.15 v + |v inmax | (gain ? 1) / 2 < v ainp , v ainn < avdd ? 0.15 v ? |v inmax | (gain ? 1) / 2 where ? v ainp , v ainn = absolute input voltage ? v inmax = v ainp ? v ainn = maximum differential input voltage (5) as mentioned in the previous section, pga gain settings of 64 and 128 are scaled in the digital domain and are not implemented with the amplifier. when using the pga in gains of 64 and 128, set the gain in equation 5 to 32 to calculate the absolute input voltage range. the relationship between the pga input to the pga output is shown graphically in figure 39 . the pga output voltages (v outp , v outn ) depend on the pga gain and the input voltage magnitudes. for linear operation, the pga output voltages must not exceed avdd ? 0.15 v or avss + 0.15 v. note that the diagram depicts a positive differential input voltage that results in a positive differential output voltage. figure 39. pga input/output range download the ads1x4s0x design calculator from www.ti.com . this calculator can be used to determine the input voltage range of the pga. 9.3.2.2 pga rail flags the pga rail flags (fl_p_railp, fl_p_railn, fl_n_railp, and fl_n_railn) in the status register (01h) indicate if the positive or negative output of the pga is closer to the analog supply rails than 150 mv. enable the pga output rail detection circuit using the fl_rail_en bit in the excitation current register 1 (06h). a flag going high indicates that the pga is operating outside the linear operating or absolute input voltage range. pga rail flags are discussed in more detail in the pga output voltage rail monitors section. 9.3.2.3 bypassing the pga at a gain of 1, the device can be configured to disable and bypass the low-noise pga. disabling the pga lowers the overall power consumption and also removes the restrictions of equation 5 for the input voltage range. if the pga is bypassed, the adc absolute input voltage range extends beyond the avdd and avss power supplies, allowing input voltages at or below ground. the absolute input voltage range when the pga is bypassed is shown in equation 6 : avss ? 0.05 v < v ainp , v ainn < avdd + 0.05 v (6) avss avdd 0.15 v avss + 0.15 v v outp = v ainp + v in a (gain 1) / 2 v outn = v ainn v in a (gain 1) / 2 v ainn v ainp v in = v ainp v ainn pga input pga output avdd advance information 31 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated in order to measure single-ended signals that are referenced to avss (ain p = v in , ain n = avss), the pga must be bypassed. the pga is bypassed and powered down by setting the pga_en[1:0] bits to 00 in the gain setting register (03h). for signal sources with high output impedance, external buffering may still be necessary. note that active buffers introduce noise and also introduce offset and gain errors. consider all of these factors in high-accuracy applications. 9.3.3 voltage reference the devices require a reference voltage for operation. the ads114s0x offers an integrated low-drift 2.5-v reference. for applications that require a different reference voltage value or a ratiometric measurement approach, the ads114s08 offers two differential reference input pairs (refp0, refn0 and refp1, refn1). the differential reference inputs allow freedom in the reference common-mode voltage. refp0 and refn0 are dedicated reference inputs, whereas refp1 and refn1 are shared with inputs ain6 and ain7 (respectively) on the ads114s08. the specified external reference voltage range is 0.5 v to avdd. the reference voltage is shown in equation 7 , where v (refpx) and v (refnx) are the absolute positive and absolute negative reference voltages. v ref = v (refpx) ? v (refnx) (7) the polarity of the reference voltage internal to the adc must be positive. the magnitude of the reference voltage together with the pga gain establishes the adc full-scale differential input range as defined by fsr = v ref / gain. figure 40 shows the block diagram of the reference multiplexer. the adc reference multiplexer selects between the internal reference and two external references (ref0 and ref1). the reference multiplexer is programmed with the refsel[1:0] bits in the reference control register (05h). by default, the external reference pair refp0, refn0 is selected. (1) the internal reference requires a minimum 1- f capacitor connected from refout to refcom. figure 40. reference multiplexer block diagram the adc also contains an integrated reference voltage monitor. this monitor provides continuous detection of a low or missing reference during the conversion cycle. the reference monitor flags (fl_ref_l0 and fl_ref_l1) are set in the status byte and described in the reference monitor section. advance information refp0 refcom refout 1 p f internal 2.5 v reference adc v refp v refn (1) 00 01 10 00 01 10 refp1 refn0 refn1 refp_buf bit of ref register 0 = enabled 1 = disabled refn_buf bit of ref register 0 = enabled 1 = disabled refcon[1:0] bits of ref register 00 = internal reference off 01 = internal reference on; off in power-down mode 10 = internal reference always on 11 = reserved refsel[1:0] bits of ref register 00 = refp0, refn0 01 = refp1, refn1 10 = internal 2.5-v reference 11 = reserved reference detection 32 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.3.1 internal reference the adc integrates a precision, low-drift, 2.5-v reference. the internal reference is enabled by setting refcon[1:0] to 10 (reference is always on) or 01 (reference is on, but powers down in power-down mode) in the reference control register (05h). by default, the internal voltage reference is powered down. to select the internal reference for use with the adc, set the refsel[1:0] bits to 10. the refout pin provides a buffered reference output voltage when the internal reference voltage is enabled. the negative reference input is the refcom pin, as shown in figure 40 . connect a capacitor in the range of 1 f to 47 f between refout and refcom. larger capacitor values help filter more noise at the expense of a longer reference start-up time. the capacitor is not required if the internal reference is not used. however, the internal reference must be powered on if using the idacs. the internal reference requires a start-up time that must be accounted for before starting a conversion, as shown in table 10 . table 10. internal reference settling time refout capacitor settling error settling time (ms) 1 f 0.01% 4.5 0.001% 5.9 10 f 0.01% 4.9 0.001% 6.3 47 f 0.01% 5.5 0.001% 7.0 9.3.3.2 external reference the ads114s0x provides two external reference inputs selectable through the reference multiplexer. the reference inputs are differential with independent positive and negative inputs. refp0 and refn0 or refp1 and refn1 can be selected as the adc reference. refp1 and refn1 are shared inputs with analog pins ain6 and ain7 in the ads114s08. without buffering, the reference input impedance is approximately 250 k . the reference input current can lead to possible errors from either high reference source impedance or through reference input filtering. to reduce the input current, use either internal or external reference buffers. in most applications external reference buffering is not necessary. connect a 100-nf bypass capacitor across the external reference input pins. follow the specified absolute and differential reference voltage requirements. 9.3.3.3 reference buffers the device has two individually selectable reference input buffers to lower the reference input current. use the refp_buf and refn_buf bits in the reference control register (05h) to enable or disable the positive and negative reference buffers respectively. note that these bits are active low. writing a 1 to refp_buf or refn_buf disables the reference buffers. the reference buffers are recommended to be disabled when the internal reference is selected for measurements. when the external reference input is at the supply voltage (refpx at avdd or refnx at avss), the reference buffer is recomended to be disabled. advance information 33 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.4 clock source the ads114s0x system clock is either provided by the internal low-drift 4.096-mhz oscillator or an external clock source on the clk input. use the clk bit within the data rate register (04h) to select the internal 4.096-mhz oscillator or an external clock source. the device defaults to using the internal oscillator. if the device is reset (from either the reset pin, or the reset command), then the clock source returns to using the internal oscillator even if an external clock is selected. 9.3.5 delta-sigma modulator a delta-sigma ( ) modulator is used in the devices to convert the analog input voltage into a pulse code modulated (pcm) data stream. the modulator runs at a modulator clock frequency of f mod = f clk / 16, where f clk is either provided by the internal 4.096-mhz oscillator or the external clock source. 9.3.6 digital filter the devices offer digital filter options for both filtering and decimation of the digital data stream coming from the delta-sigma modulator. the implementation of the digital filter is determined by the data rate and filter mode setting. figure 41 shows the digital filter implementation. choose between a third-order sinc filter (sinc 3 ) and a low-latency filter (low-latency filter with multiple components) using the filter bit in the data rate register (04h). note: ll filter = low-latency filter. figure 41. digital filter architecture advance information sinc 3 filter f clk = 4.096 mhz f clk / 16 f mod = 256 khz adc dr[3:0] bits of datarate register adc data output sinc 1 filter ll1 filter 4000, 2000, 1000, 800, 400, 200, 100, 60, 50, 20, 16.6, 10, 5, 2.5 sps ll2 filter sinc 1 filter 20, 10, 5, 2.5 sps 400, 200, 100, 60, 50, 16.6 sps 4000, 2000, 1000, 800 sps sinc 3 filter low-latency filter filter bit of datarate register 0 = sinc 3 filter 1 = low-latency filter 0000 = 2.5 sps 0001 = 5 sps 0010 = 10 sps 0011 = 16.6 sps 0100 = 20 sps 0101 = 50 sps 0110 = 60 sps 0111 = 100 sps 1000 = 200 sps 1001 = 400 sps 1010 = 800 sps 1011 = 1000 sps 1100 = 2000 sps 1101 = 4000 sps 1110 = 4000 sps 1111 = reserved 34 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated regardless of the filter type setting, the oversampling ratio is the same for each given data rate, meaning that the device requires a set number of modulator clocks to output a single adc conversion data. the output data rate is selected using the dr[3:0] bits in the data rate register and is shown in table 11 . (1) valid for the internal oscillator or an external 4.096-mhz clock. (2) the oversampling ratio is f mod divided by the data rate; f mod = f clk / 16. table 11. adc data rates and digital filter oversampling ratios nominal data rate (sps) (1) data rate register dr[3:0] oversampling ratio (2) 2.5 0000 102400 5 0001 51200 10 0010 25600 16.6 0011 15360 20 0100 12800 50 0101 5120 60 0110 4264 100 0111 2560 200 1000 1280 400 1001 640 800 1010 320 1000 1011 256 2000 1100 128 4000 1101 64 9.3.6.1 low-latency filter the low-latency filter is selected when the filter bit is set to 0 in the data rate register (04h). the filter is a finite impulse response (fir) filter that provides settled data, given that the analog input signal has settled to the final value before the conversion is started. the low-latency filter is especially useful when multiple channels must be scanned in minimal time. 9.3.6.1.1 low-latency filter frequency response the low-latency filter provides many data rate options for rejecting 50-hz and 60-hz line cycle noise. at data rates of 2.5 sps, 5 sps, 10 sps, and 20 sps, the filter rejects both 50-hz and 60-hz line frequencies. at data rates of 16.6 sps and 50 sps, the filter has a notch at 50 hz. at a 60-sps data rate, the filter has a notch at 60 hz. for detailed frequency response plots showing line cycle noise rejection, download the ads1x4s0x design calculator from www.ti.com . advance information 35 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated figure 42 to figure 56 show the frequency response of the low-latency filter for different data rates. table 12 gives the bandwidth of the low-latency filter for each data rate. f clk = 4.096 mhz, low-latency filter figure 42. low-latency filter frequency response, data rate = 2.5 sps f clk = 4.096 mhz, low-latency filter figure 43. low-latency filter frequency response, data rate = 5 sps f clk = 4.096 mhz, low-latency filter figure 44. low-latency filter frequency response, data rate = 10 sps f clk = 4.096 mhz, low-latency filter figure 45. low-latency filter frequency response, data rate = 16.6 sps f clk = 4.096 mhz, low-latency filter figure 46. low-latency filter frequency response, data rate = 20 sps f clk = 4.096 mhz, low-latency filter figure 47. low-latency filter frequency response, data rate = 20 sps, zoomed to 50 hz and 60 hz frequency (hz) magnitude (db) 0 20 40 60 80 100 120 140 160 -60 -40 -20 0 frequency (hz) magnitude (db) 0 10 20 30 40 50 60 70 -120 -100 -80 -60 -40 -20 0 advance information frequency (hz) magnitude (db) 0 10 20 30 40 50 60 70 -120 -100 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 0 20 40 60 80 100 120 140 160 180 200 -120 -100 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 40 45 50 55 60 65 70 -120 -100 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 0 10 20 30 40 50 60 70 80 90 100 -120 -100 -80 -60 -40 -20 0 36 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated f clk = 4.096 mhz, low-latency filter figure 48. low-latency filter frequency response, data rate = 50 sps f clk = 4.096 mhz, low-latency filter figure 49. low-latency filter frequency response, data rate = 60 sps f clk = 4.096 mhz, low-latency filter figure 50. low-latency filter frequency response, data rate = 100 sps f clk = 4.096 mhz, low-latency filter figure 51. low-latency filter frequency response, data rate = 200 sps f clk = 4.096 mhz, low-latency filter figure 52. low-latency filter frequency response, data rate = 400 sps f clk = 4.096 mhz, low-latency filter figure 53. low-latency filter frequency response, data rate = 800 sps frequency (hz) magnitude (db) 0 1000 2000 3000 4000 5000 6000 7000 8000 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 0 500 1000 1500 2000 2500 3000 3500 4000 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 0 200 400 600 800 1000 -60 -40 -20 0 frequency (hz) magnitude (db) 0 400 800 1200 1600 2000 -60 -40 -20 0 frequency (hz) magnitude (db) 0 100 200 300 400 -60 -40 -20 0 advance information frequency (hz) magnitude (db) 0 50 100 150 200 250 300 350 400 -60 -40 -20 0 37 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated f clk = 4.096 mhz, low-latency filter figure 54. low-latency filter frequency response, data rate = 1 ksps f clk = 4.096 mhz, low-latency filter figure 55. low-latency filter frequency response, data rate = 2 ksps f clk = 4.096 mhz, low-latency filter figure 56. low-latency filter frequency response, data rate = 4 ksps (1) valid for the internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . table 12. low-latency filter bandwidth nominal data rate (sps) (1) ? 3-db bandwidth (hz) (1) 2.5 1.1 5 2.2 10 4.7 16.6 7.4 20 13.2 50 22.1 60 26.6 100 44.4 200 89.9 400 190 800 574 1000 718 2000 718 4000 718 frequency (hz) magnitude (db) 0 4000 8000 12000 16000 20000 -100 -80 -60 -40 -20 0 advance information frequency (hz) magnitude (db) 0 8000 16000 24000 32000 40000 -100 -80 -60 -40 -20 0 frequency (hz) magnitude (db) 0 2000 4000 6000 8000 10000 -80 -60 -40 -20 0 38 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) valid for the internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . (2) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (3) time does not include the programmable delay set by the delay[2:0] bits in the gain setting register. the default setting is an additional 14 t mod , where t mod = t clk 16. (4) subsequent readings in continuous conversion mode do not have the programmable delay time. the low-latency filter notches and output data rate scale proportionally with the clock frequency. for example, a notch that appears at 20 hz when using a 4.096-mhz clock appears at 10 hz if a 2.048-mhz clock is used. note that the internal oscillator can vary over temperature as specified in the electrical characteristics table. the data rate, conversion time, and filter notches consequently vary by the same percentage. consider using an external precision clock source if a digital filter notch at a specific frequency with a tighter tolerance is required. 9.3.6.1.2 data conversion time for the low-latency filter the amount of time required to receive data from the adc depends on more than just the nominal data rate of the device. the data period also depends on the mode of operation and other configurations of the device. when the low-latency filter is enabled, the data settles in one data period. however, a small amount of latency exists to set up the device, calculate the conversion data from the modulator samples, and other overhead that adds time to the conversion. for this reason, the first conversion data takes longer than subsequent data conversions. table 13 shows the conversion times for the low-latency filter for each adc data rate and various conversion modes. table 13. data conversion time for the low-latency filter nominal data rate (1) (sps) first data for continuous conversion mode or single-shot conversion mode (2) second and subsequent conversions for continuous conversion mode ms (3) number of t mod periods (3) ms (4) number of t mod periods (4) 2.5 406.504 104065 400 102400 5 206.504 52865 200 51200 10 106.504 27265 100 25600 16.6 60.254 15425 60 15360 20 56.504 14465 50 12800 50 20.156 5160 20 5120 60 16.910 4329 16.66 4264 100 10.156 2600 10 2560 200 5.156 1320 5 1280 400 2.656 680 2.5 640 800 1.406 360 1.25 320 1000 1.156 296 1 256 2000 0.656 168 0.5 128 4000 0.406 104 0.25 64 advance information 39 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.6.2 sinc 3 filter the sinc 3 digital filter is selected when the filter bit is set to 0 in the data rate register (04h). compared to the low-latency filter, the sinc 3 filter has improved noise performance but has a three-cycle latency in the data output. 9.3.6.2.1 sinc 3 filter frequency response the low-pass nature of the sinc 3 filter establishes the overall frequency response. the frequency response is given by equation 8 : where ? f = signal frequency ? f clk = adc clock frequency ? osr = oversampling ratio (8) the sinc 3 filter offers simultaneous 50-hz and 60-hz line cycle rejection at data rates of 2.5 sps, 5 sps, and 10 sps. the sinc 3 filter offers only 50-hz rejection at data rates of 16.6 sps and 50 sps, and only 60-hz rejection at data rates of 20 sps and 60 sps. the sinc 3 digital filter response scales with the data rate and has notches at multiples of the data rate. figure 57 shows the sinc 3 digital filter frequency response normalized to the data rate. as an example, figure 58 shows the frequency response when the data rate is set to 10 sps, and figure 59 illustrates a close-up of the filter rejection of 50-hz and 60-hz line frequencies. for more detailed frequency response plots, download the ads1x4s0x design calculator from www.ti.com . table 14 gives the bandwidth of the sinc 3 filter for each data rate. frequency normalized to data rate, sinc 3 filter figure 57. sinc 3 filter frequency response, normalized to data rate f clk = 4.096 mhz, sinc 3 filter figure 58. sinc 3 filter frequency response, data rate = 10 sps advance information frequency (hz) magnitude (db) 0 10 20 30 40 50 60 70 80 90 100 -120 -100 -80 -60 -40 -20 0 normalized frequency magnitude (db) 0 1 2 3 4 5 6 7 8 9 10 -120 -100 -80 -60 -40 -20 0 3 clk sinc3 clk 16 f osr sin f h(f ) h (f ) 16 f osr sin f s ? ? ? 1 s u ? ? 1 40 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated f clk = 4.096 mhz, sinc 3 filter figure 59. sinc 3 filter frequency response, data rate = 10 sps, zoomed to 50 hz and 60 hz (1) valid for the internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . table 14. sinc 3 filter ? 3-db bandwidth nominal data rate (sps) (1) ? 3-db bandwidth (hz) (1) 2.5 0.65 5 1.3 10 2.6 16.6 4.4 20 5.2 50 13.1 60 15.7 100 26.2 200 52.3 400 105 800 209 1000 262 2000 523 4000 1046 as mentioned in the previous section, filter notches and output data rate scale proportionally with the clock frequency and the internal oscillator can change frequency with temperature. frequency (hz) magnitude (db) 40 45 50 55 60 65 70 -140 -120 -100 -80 -60 -40 -20 0 advance information 41 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) valid for the internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . (2) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (3) time does not include the programmable delay set by the delay[2:0] bits in the gain setting register. the default setting is an additional 14 t mod , where t mod = t clk 16. (4) subsequent readings in continuous conversion mode do not have the programmable delay time. 9.3.6.2.2 data conversion time for the sinc 3 filter similar to the low-latency filter, the sinc 3 filter requires different amounts of time to complete a conversion. by nature, the sinc 3 filter normally takes three conversion to settle. in both single-shot conversion mode and continuous conversion mode, the first two conversions are suppressed so that only settled data are output by the adc. table 15 shows the conversion times for the sinc 3 filter for each adc data rate and various conversion modes. table 15. data conversion time for the sinc 3 filter nominal data rate (1) (sps) first data for continuous conversion mode or single-shot conversion mode (2) second and subsequent conversions for continuous conversion mode ms (3) number of t mod periods (3) ms (4) number of t mod periods (4) 2.5 1200.254 307265 400 102400 5 600.254 153665 200 51200 10 300.254 76865 100 25600 16.6 180.254 46145 60 15360 20 150.254 38465 50 12800 50 60.254 15425 20 5120 60 50.223 12857 16.66 4264 100 30.254 7745 10 2560 200 15.254 3905 5 1280 400 7.754 1985 2.5 640 800 4.004 1025 1.25 320 1000 3.156 808 1 256 2000 1.656 424 0.5 128 4000 0.906 232 0.25 64 9.3.6.3 note on conversion time each data period consists of time required for the modulator to sample the analog inputs. however, there is additional time required before the samples become an adc conversion result. first, there is a programmable conversion delay (described in the programmable conversion delay section) that is added before the conversion starts. this delay allows for additional settling time for input filtering on the analog inputs and for the antialiasing filter after the pga. the default programmable conversion delay is 14 t mod . also, overhead time is needed to convert the modulator samples into an adc conversion result. this overhead time includes any necessary offset or gain compensation after the digital filter accumulates a data result. the first conversion when the device is in continuous conversion mode (just as in single-shot conversion mode) includes the programmable conversion delay, the modulator sampling time, and the overhead time. the second and subsequent conversions are the normal data period (period as given by the inverse of the data rate). advance information 42 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated figure 60 shows the time sequence for the adc in both continuous conversion and single-shot conversion modes. the sequence is the same regardless of the filter setting. however, when the low-latency filter settles for each data, the sinc 3 filter does not settle until the third data. (1) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (2) in sinc 3 filter mode, the first two data outputs are suppressed to allow for the measurement data to settle. (3) in sinc 3 filter mode, there is no overhead time for the first two data, which are not available to be read. figure 60. single-shot conversion mode and continuous conversion mode sequences sampling for first data x x data ready conversion start (1) single-shot conversion mode: low-latency filter sampling for first data. x x data not settled data not settled filter settled first data ready (2) conversion start (1) sampling for second data. sampling for third data. single-shot conversion mode: sinc 3 filter x programmable delay modulator sampling adc overhead sampling for first data. x x first data ready (3) second data ready third data ready conversion start (1) sampling for second data. sampling for third data. continuous conversion mode: low-latency or sinc 3 filter drdy drdy drdy drdy low-latency filter sinc 3 filter sampling for fourth data. fourth data ready continued sampling. advance information 43 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) f clk = 4.096 mhz. 9.3.6.4 50-hz and 60-hz line cycle rejection if the adc connection leads are in close proximity to industrial motors and conductors, coupling of 50-hz and 60-hz power line frequencies can occur. the coupled noise interferes with the signal voltage, and can lead to inaccurate or unstable conversions. the digital filter provides enhanced rejection of power-line-coupled noise for data rates of 60 sps and less. program the filter to tradeoff data rate and conversion latency versus the desired level of line cycle rejection. table 16 and table 17 summarize the adc 50-hz and 60-hz line-cycle rejection based on 1-hz and 2-hz tolerance of power-line to adc clock frequency. the best possible power-line rejection is provided by using an accurate adc clock. table 16. low-latency filter, 50-hz and 60-hz line cycle rejection data rate (sps) (1) low-latency digital filter line cycle rejection (db) 50 hz 1 hz 60 hz 1 hz 50 hz 2 hz 60 hz 2 hz 2.5 ? 113.7 ? 95.4 ? 97.7 ? 92.4 5 ? 111.9 ? 95.4 ? 87.6 ? 81.8 10 ? 111.5 ? 95.4 ? 85.7 ? 81.0 16.6 ? 33.8 ? 20.9 ? 27.8 ? 20.8 20 ? 95.4 ? 95.4 ? 75.5 ? 80.5 50 ? 33.8 ? 15.5 ? 27.6 ? 15.1 60 ? 13.4 ? 35.0 ? 12.6 ? 29.0 (1) f clk = 4.096 mhz. table 17. sinc 3 filter, 50-hz and 60-hz line cycle rejection data rate (sps) (1) sinc 3 digital filter line cycle rejection (db) 50 hz 1 hz 60 hz 1 hz 50 hz 2 hz 60 hz 2 hz 2.5 ? 108.7 ? 113.4 ? 107.2 ? 112.1 5 ? 103.2 ? 107.8 ? 90.1 ? 95.0 10 ? 101.8 ? 106.4 ? 84.6 ? 89.4 16.6 ? 101.6 ? 63.0 ? 83.4 ? 62.4 20 ? 53.5 ? 106.1 ? 53.5 ? 88.0 50 ? 101.4 ? 46.7 ? 82.9 ? 45.3 60 ? 40.3 ? 105.1 ? 37.8 ? 87.2 advance information 44 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) valid for internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . (2) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (3) time does not include the programmable delay set by the delay[2:0] bits in the gain setting register. global chop mode requires two conversions, doubling the additional time. the default setting adds an extra 28 t mod (where t mod = t clk 16) to this column. 9.3.6.5 global chop mode the device uses a very low-drift pga and modulator in order to provide very low input voltage offset drift. however, a small amount of offset voltage drift sometimes remains in normal measurement. the adc incorporates a global chop option to reduce the offset voltage and offset voltage drift to very low levels. when the global chop is enabled, the adc performs two internal conversions to cancel the input offset voltage. the first conversion is taken with normal input polarity. the adc reverses the internal input polarity for a second conversion. the average of the two conversions yields the final corrected result, removing the offset voltage. the global chop mode is enabled using the g_chop bit in the data rate register (04h). figure 61 shows a block diagram of the global chop implementation. the combined pga and adc internal offset voltage is modeled as v ofs . figure 61. adc global chop block diagram the first conversion result is available after the adc takes two separate conversions with settled data. when using the low-latency filter, data settles in a single conversion. when the global chop mode is enabled, the first conversion result appears after a time period of approximately two conversions. when using the sinc 3 filter, data settles in three conversions. if the global chop mode is enabled, the first conversion result appears after a time period of approximately six conversions. in continuous conversion mode with the global chop mode enabled, subsequent conversions complete in half the time as the first conversion completed. data for alternating inputs are pipelined so that averaging appears on each adc data cycle. conversion times using the global chop mode are given in table 18 and table 19 . table 18. data conversion time for global chop mode using the low-latency filter nominal data rate (1) (sps) first data conversion period for global chop mode (2) second and subsequent conversion periods for global chop mode ms (3) number of t mod periods (3) ms (3) number of t mod periods (3) 2.5 813.008 208130 406.504 104065 5 413.008 105730 206.504 52865 10 213.008 54530 106.504 27265 16.66 120.508 30850 60.254 15425 20 113.008 28930 56.504 14465 50 40.313 10320 20.156 5160 60 33.820 8658 16.910 4329 100 20.313 5200 10.156 2600 200 10.313 2640 5.156 1320 400 5.313 1360 2.656 680 800 2.813 720 1.406 360 1000 2.313 592 1.156 296 2000 1.313 336 0.656 168 4000 0.813 208 0.406 104 v ofs adc pga adc digital filter + - chop control conversion output input mux chop switch ain p ain n g_chop bit of datarate register 0 = global chop off 1 = global chop on ain0 aincom advance information 45 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) valid for internal oscillator or an external 4.096-mhz clock. scales proportional with f clk . (2) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (3) time does not include the programmable delay set by the delay[2:0] bits in the gain setting register. global chop mode requires two conversions, doubling the additional time. the default setting adds an extra 28 t mod (where t mod = t clk 16) to this column. table 19. data conversion time for global chop mode using the sinc 3 filter nominal data rate (1) (sps) first data conversion period for global chop mode (2) second and subsequent conversion periods for global chop mode ms (3) number of t mod periods (3) ms (3) number of t mod periods (3) 2.5 2400.508 614530 1200.254 307265 5 1200.508 307330 600.254 153665 10 600.508 153730 300.254 76865 16.66 360.508 92290 180.254 46145 20 300.508 76930 150.254 38465 50 120.508 30850 60.254 15425 60 100.445 25714 50.223 12857 100 60.508 15490 30.254 7745 200 30.508 7810 15.254 3905 400 15.508 3970 7.754 1985 800 8.008 2050 4.004 1025 1000 6.313 1616 3.156 808 2000 3.313 848 1.656 424 4000 1.813 464 0.906 232 in global chop mode, sequences are similar to taking consecutive single-shot conversions and swapping the input on each conversion. output data are averaged using the last two data read operations by the adc with the inputs swapped. figure 62 shows the time sequence for the adc using global chop mode. (1) conversions start at the rising edge of the start/sync pin or on the seventh sclk falling edge for a start command. (2) when the first data are collected, the inputs are swapped. (3) measurements are averaged after the inputs are swapped for each conversion. figure 62. global chop enabled conversion mode sequences because the digital filter must settle after reversing the inputs, the global chop mode data rate is less than the nominal data rate, depending on the digital filter and programmed settling delay. however, if the data rate in use has 50-hz and 60-hz frequency response notches, the null frequencies remain unchanged. advance information sampling for positive input data x inputs swapped (2) conversion start (1) global chop enabled, continuous conversion mode: low- latency filter sampling x data not settled inputs swapped (2) conversion start (1) sampling sampling for positive input data global chop enabled, continuous conversion mode: sinc 3 filter sampling for negative input data x first data ready sampling x sampling sampling for negative input data first data ready x programmable delay modulator sampling adc overhead sampling for positive input data xx second data ready additional sampling xx averaged for first data sampling for negative input data averaged for second data (3) averaged for third data third data ready x averaged for first data averaged for second data (3) xx sampling for positive input data second data ready continued sampling x data not settled data not settled data not settled 46 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated the global chop mode also reduces the adc noise by a factor of 2 because two conversions are averaged. in some cases, the programmable conversion delay must be increased, delay[2:0] in the gain setting register (03h), to allow for settling of external components. 9.3.7 excitation current sources (idacs) the ads114s0x incorporates two integrated, matched current sources (idac1, idac2). the current sources provide excitation current to resistive temperature devices (rtds), thermistors, diodes, and other resistive sensors that require constant current biasing. the current sources are programmable to output values between 10 a to 2000 a using the imag[3:0] bits in the excitation current register 1 (06h). each current source can be connected to any of the analog inputs ainx as well as the refp1 and refn1 inputs for the ads114s06. both current sources can also be connected to the same pin. the routing of the idacs is configured by the i1mux[3:0] and i2mux[3:0] bits in the excitation current register 2 (07h). in three-wire rtd applications, the matched current sources can be used to cancel errors caused by sensor lead resistance (see the typical application section for more details). figure 63 details the idac connection through the input multiplexer. figure 63. idac block diagram the internal reference must be enabled for idac operation. as a current source, the idac requires voltage headroom to the positive supply to operate. this voltage headroom is the compliance voltage. when driving resistive sensors and biasing resistors, take care not to exceed the compliance voltage of the idacs, otherwise the specified accuracy of the idac current may not be met. for idac compliance voltage specifications, see the electrical characteristics table. advance information ain0 ain1 ain2 ain3 ain4 ain5 ain6 / refp1 ain7 / refn1 ain8 ain9 i1mux[3:0] bits of the idacmux register. idac routing to ain8 ain11 is available only on the ads114s08. i2mux[3:0] bits of the idacmux register. idac routing to ain8 ain11 is available only on the ads114s08. imag[3:0] bits of the idacmag register. 0000 = off 0001 = 10 a 0010 = 50 a 0011 = 100 a 0100 = 250 a 0101 = 500 a 0110 = 750 a 0111 = 1000 a 1000 = 1500 a 1001 = 2000 a avdd avdd idac1 idac2 ain10 ain11 aincom idac1 mux ain0 ain1 ain2 ain3 ain4 ain5 ain6/refp1 ain7/refn1 ain8 ain9 aincom ain10 ain11 no connection 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 idac2 mux ain0 ain1 ain2 ain3 ain4 ain5 ain6/refp1 ain7/refn1 ain8 ain9 aincom ain10 ain11 no connection 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101-1111 1101-1111 ads114s08 only copyright ? 2017, texas instruments incorporated 47 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.8 bias voltage generation the ads114s0x provides an internal bias voltage generator, vbias, that can be set to two different levels, (avdd + avss) / 2 and (avdd + avss) / 12 by using the vb_level bit in the sensor biasing register (08h). the bias voltage is internally buffered and can be established on the analog inputs ain0 to ain5 and aincom using the vb_ainx bits in the sensor biasing register (08h). a typical use case for vbias is biasing unbiased thermocouples to within the common-mode voltage range of the pga. a block diagram of the vbias voltage generator and connection diagram is shown in figure 64 . figure 64. vbias block diagram the start-up time of the vbias voltage depends on the pin load capacitance. the total capacitance includes any capacitance connected from vbias to avdd, avss, and ground. table 20 lists the vbias voltage settling times for various external load capacitances. ensure the vbias voltage is fully settled before starting a conversion. table 20. vbias settling time load capacitance settling time 0.1 f 280 s 1 f 2.8 ms 10 f 28 ms advance information aincom input mux 6r avdd avss (avdd + avss) / 2 (avdd + avss) / 12 vb_level bit of vbias register 0 = (avdd + avss) / 2 1 = (avdd + avss) / 12 ain5 ain3 ain4 ain0 ain1 ain2 vb_ainx bits of vbias register 0 = vbias not connected to ainx 1 = vbias connected to ainx r 5r 48 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.9 system monitor the ads114s0x provides a set of system monitor functions. these functions measure the device temperature, analog power supply, digital power supply, or use current sources to detect sensor malfunction. system monitor functions are enabled through the sys_mon[2:0] bits of the system control register (09h). 9.3.9.1 internal temperature sensor on-chip diodes provide temperature-sensing capability. enable the internal temperature sensor by setting sys_mon[2:0] = 010 in the system control register (09h). the temperature sensor outputs a voltage proportional to the device temperature as specified in the electrical characteristics table. when measuring the internal temperature sensor, the analog inputs are disconnected from the adc and the output voltage of the temperature sensor is routed to the adc for measurement using the selected pga gain, data rate, and voltage reference. if enabled, pga gain must be limited to 4 for the temperature sensor measurement to remain within the allowed absolute input voltage range of the pga. as a result of the low device junction-to-pcb thermal resistance (r jb ), the internal device temperature closely tracks the printed circuit board (pcb) temperature. 9.3.9.2 power supply monitors the ads114s0x provides a means for monitoring both the analog and digital power supply (avdd and dvdd). the power-supply voltages are divided by a resistor network to reduce the voltages to within the adc input range. the reduced power-supply voltage is routed to the adc input multiplexer. the analog (v anlmon ) and digital (v digmon ) power-supply readings are scaled by equation 9 and equation 10 , respectively: v anlmon = (avdd ? avss) / 4 (9) v digmon = (dvdd ? dgnd) / 4 (10) enable the supply voltage monitors using the sys_mon[2:0] bits in the system control register (09h). setting sys_mon[2:0] to 011 measures v anlmon , and setting sys_mon[2:0] to 100 measures v digmon . when the supply voltage monitor is enabled, the analog inputs are disconnected from the adc and the pga gain is set to 1, regardless of the gain[2:0] bit values in the gain setting register (03h). supply voltage monitor measurements can be done with either the pga enabled or pga disabled via the pga_en[1:0] register. to obtain valid power supply monitor readings, the reference voltage must be larger than the power-supply measurements shown in equation 9 and equation 10 . 9.3.9.3 burn-out current sources to help detect a possible sensor malfunction, the ads114s0x provides selectable current sources to function as burn-out current sources (bocs) using the sys_mon[2:0] bits in the system control register (09h). current sources are set to values of 0.2 a, 1 a, and 10 a with sys_mon[2:0] settings of 101, 110, and 111, respectively. when enabled, one bocs sources current to the selected positive analog input (ain p ) and the other bocs sinks current from the selected negative analog input (ain n ). with an open-circuit in a burned out sensor, these bocss pull the positive input towards avdd and the negative input towards avss, resulting in a full-scale reading. a full-scale reading can also indicate that the sensor is overloaded or that the reference voltage is absent. a near-zero reading can indicate a shorted sensor. distinguishing a shorted sensor condition from a normal reading can be difficult, especially if an rc filter is used at the inputs. the voltage drop across the external filter resistance and the residual resistance of the multiplexer can cause the output to read a value higher than zero. the adc readings of a functional sensor can be corrupted when the burn-out current sources are enabled. the burn-out current sources are recommended to be disabled when performing the precision measurement, and only enabling them to test for sensor fault conditions. if the global chop mode is enabled, disable this mode before making a measurement with the burn-out current sources. advance information 49 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.10 status register the ads114s0x has a one-byte status register that contains flags to indicate if a fault condition has occurred. this byte can be read out from the status register (01h), or can be prepended to each data read as the first byte when reading data from the adc. to prepend the status byte to each conversion result, set the sendstat bit to 1 in the system control register (09h). the status byte data field and field description are found in figure 82 and table 27 . the following sections describe various flagged fault conditions that are indicated in the status byte. flags for the pga output voltage rail monitors and reference monitor are set after each conversion. reading the status byte reads the flags latched during the last conversion cycle. 9.3.10.1 por flag after the power supplies are turned on, the adc remains in reset until dvdd, iovdd, and the analog power supply (avdd ? avss) voltage exceed the respective power-on reset (por) voltage thresholds. if a por event has occurred, the fl_por flag (bit 7 of the status byte) is set. this flag indicates that a por event has occurred and has not been cleared. this flag is cleared with a user register write to set the bit to 0. the power-on reset is described further in the power-on reset section. 9.3.10.2 rdy flag the rdy flag indicates that the device has started up and is ready to receive a configuration change. during a reset or por event, the device is resetting the register map and may not be available. the rdy flag is shown with bit 6 of the status byte. 9.3.10.3 pga output voltage rail monitors the pga contains an integrated output-voltage monitor. if the level of the pga output voltage exceeds avdd ? 0.15 v or drops below avss + 0.15 v, a flag is set to indicate that the output has gone beyond the output range of the pga. each pga output v outn and v outp can trigger an overvoltage or undervoltage flag, giving a total of four flags. the pga output voltage rail monitors are enabled with the fl_ref_en bit of excitation current register 1. the pga output voltage rail monitor block diagram is shown in figure 65 . if the pga is bypassed, then the rail monitor is still operational and is sensing the connection at the input of the adc. the pga output voltage rail monitors are: ? fl_p_railp (bit 5 of the status byte): v outp has exceeded avdd ? 0.15 v ? fl_p_railn (bit 4 of the status byte): v outp dropped below avss + 0.15 v ? fl_n_railp (bit 3 of the status byte): v outn has exceeded avdd ? 0.15 v ? fl_n_railn (bit 2 of the status byte): v outn dropped below avss + 0.15 v figure 65. pga output voltage rail monitors advance information avdd 0.15 v v outp v outn s q r + adc pga adc avss + 0.15 v supply rail comparators status byte [5:2] conversion start reset latch s q r + s q r + s q r + fl_p_railp fl_p_railn fl_n_railp fl_n_railn 50 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated figure 66 shows an example of a pga output voltage rail monitor overrange event and the respective behavior of the flags. a fault is latched during a conversion cycle. the flags are updated (set or cleared) only at the end of a conversion cycle. figure 66. pga output voltage rail monitor timing 9.3.10.4 reference monitor the user can select to continuously monitor the adc reference inputs for a shorted or missing reference voltage. the reference detection circuit offers two thresholds, the first threshold is 300 mv and the second threshold is 1/3 (avdd ? avss). the reference detection circuit measures the differential reference voltage and sets a flag latched after each conversion in the status byte if the voltage is below the threshold. a reference voltage less than 300 mv can indicate a potential short on the reference inputs or, in case of a ratiometric rtd measurement, a broken wire between the rtd and the reference resistor. a reference voltage between 300 mv and 1/3 (avdd ? avss) can indicate a broken sensor excitation wire in a 3-wire rtd setup. additionally, a resistor of 10 m can be connected between the selected refpx and refnx inputs. the resistor can be used to detect a floating reference input. with a floating input, the resistor pulls both reference inputs to the same potential so that the reference detection circuit can detect this condition. the pull-together reference resistor is not recommended to be continuously connected to active reference inputs. this resistor lowers the input impedance of the reference inputs and can contribute gain error to the measurement. the reference detection circuits must be enabled with the fl_ref_en[1:0] bits of the reference control register (05h). the fl_ref_l0 flag (bit 0 of the status byte) indicates if the reference voltage is lower than 0.3 v. the fl_ref_l1 flag (bit 1 of the status byte) indicates if the reference voltage is lower than 1/3 (avdd ? avss). a diagram of the reference detection circuit is shown in figure 67 . a reference monitor fault is latched at each conversion cycle and the flags in the status register are updated at the falling edge of drdy. figure 67. reference monitor block diagram refpx refnx s q r 0.3 v conversion start reset fl_ref_en[1:0] bits of ref register 00 = reference monitor off 01 = 0.3 v threshold enabled 10 = 1/3 ? (avdd - avss) threshold enabled 11 = 0.3 v threshold and 10-m pull-together enabled fl_ref_l0 bit of status register 0 = no alarm 1 = alarm + + s q r 1/3 ? (avdd avss) + 10 m fl_ref_l1 bit of status register 0 = no alarm 1 = alarm conversions (drdy) pga positive output (v) avdd - 0.15 v fl_p_railp bit flag latched during conversion cycle avss + 0.15 v fl_p_railn bit (v outp ) advance information 51 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.11 general-purpose inputs and outputs (gpios) the ads114s06 offers four dedicated general-purpose input and output (gpio) pins, and the ads114s08 offers four pins (ain8 to ain11) that serve a dual purpose as either analog inputs or gpios. two registers control the function of the gpio pins. use the con[3:0] bits of the gpio configuration register (11h) to configure a pin as a gpio pin. the upper four bits (dir[3:0]) of the gpio data register (10h) configure the gpio pin as either an input or an output. the lower four bits (dat[3:0]) of the gpio data register contain the input or output gpio data. if a gpio pin is configured as an input, the respective dat[x] bit reads the status of the pin; if a gpio pin is configured as an output, write the output status to the respective dat[x] bit. for more information about the use of gpio pins, see the configuration registers section. figure 68 shows a diagram of how these functions are combined onto a single pin. note that when the pin is configured as a gpio, the corresponding logic is powered from avdd and avss. when the devices are operated with bipolar analog supplies, the gpio outputs bipolar voltages. care must be taken to not load the gpio pins when used as outputs because large currents can cause droop or noise on the analog supplies. gpio pins use schmitt triggered inputs, with hysteresis to make the input more resistance to noise; see the electrical characteristics table for gpio thresholds. figure 68. gpio block diagram for connections of unused gpio pins, see the unused inputs and outputs section. 9.3.12 low-side power switch a low-side power switch with low on-resistance connected between refn0 and avss-sw is integrated in the devices. this power switch can be used to reduce system power consumption in resistive bridge sensor applications by powering down the bridge circuit between conversions. when the psw bit in the excitation current register 1 (06h) is set to 1, the switch closes. the switch automatically opens when the powerdown command is issued. the switch is opened by setting the psw bit to 0. by default, the switch is open. connect avss-sw to avss. advance information ain8 con[3:0] bits of gpiocon register 0 = no connect 1 = connect dir[7:4] bits of gpiodat register 0 = output 1 = input dat[3:0] bits of gpiodat register 0 = v gpio is low 1 = v gpio is high ain9 ain10 ain11 gpio[0] gpio[1] gpio[2] gpio[3] gpio 1 of 4 avss avdd write read gpio read select 1 0 0 gpio logic is powered from avdd to avss 52 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.13 cyclic redundancy check (crc) a cyclic redundancy check (crc) is enabled by setting the crc bit to 1 in the system control register (10h). when crc mode is enabled, the 8-bit crc is appended to the conversion result. the crc is calculated for the 16-bit conversion result and the status byte when enabled. in crc mode, the checksum byte is the 8-bit remainder of the bitwise exclusive-or (xor) of the data bytes by a crc polynomial. for conversion data, use three data bytes. the crc is based on the crc-8-atm (hec) polynomial: x 8 + x 2 + x + 1. the nine binary coefficients of the polynomial are: 100000111. to calculate the crc, divide (xor operation) the data bytes (excluding the crc) with the polynomial and compare the calculated crc values to the adc crc value. if the values do not match, a data transmission error has occurred. in the event of a data transmission error, read the data again. the following list shows a general procedure to compute the crc value: 1. left-shift the initial 16-bit data value ( 24-bit data when the status byte is enabled) by 8 bits, with zeros padded to the right, creating a new 24-bit data value (the starting data value). 2. align the msb of the crc polynomial (100000111) to the left-most, logic-one value of the data. 3. perform an xor operation on the data value with the aligned crc polynomial. the xor operation creates a new, shorter-length value. the bits of the data values that are not in alignment with the crc polynomial drop down and append to the right of the new xor result. 4. when the xor result is less than 100000000, the procedure ends, yielding the 8-bit crc value. otherwise, continue with the xor operation shown in step 2, using the current data value. the number of loop iterations depends on the value of the initial data. 9.3.14 calibration the adc incorporates offset and gain calibration commands, as well as user-offset and full-scale (gain) calibration registers to calibrate the adc. the adc calibration registers are 16 bits wide. use calibration to correct internal adc errors or overall system errors. calibrate by sending calibration commands to the adc, or by direct user calibration. in user calibration, the user calculates and writes the correction values to the calibration registers. the adc performs self or system-offset calibration, or a system gain calibration. perform offset calibration before system gain calibration. after power-on, wait for the power supplies and reference voltage to fully settle before calibrating. as shown in figure 69 , the value of the offset calibration register is subtracted from the filter output and then multiplied by the full-scale register value divided by 4000h. the data are then clipped to a 16-bit value to provide the final output. figure 69. adc calibration block diagram calibration commands cannot be used when the device is in standby mode (when the start/sync pin is low, or when the stop command is issued). + ofcal[1:0] registers (register addresses = 0ch, 0bh, 0ah) > 0000h: negative offset = 0000h: no offset < 0000h: positive offset ain p 1/4000h fscal[1:0] registers (register addresses = 0fh, 0eh, 0dh) < 4000h: gain > 1 = 4000h: gain = 1 > 4000h: gain < 1 - digital filter adc adc output data clipped to 16 bits final output ain n advance information 53 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.3.14.1 offset calibration the offset calibration word is 16 bits, consisting of two 8-bit registers, as shown in the two registers starting with offset calibration register 1 . the offset value is twos complement format with a maximum positive value equal to 7fffh, and a maximum negative value equal to 8000h. this value is subtracted from each output reading as an offset correction. a register value equal to 0000h has no offset correction. if global chop mode is enabled, the offset calibration register is disabled. table 21 shows example settings of the offset register. (1) ideal output code with shorted input, excluding adc noise and offset voltage error. table 21. offset calibration register values ofc[1:0] register value offset calibrated output code (1) 0001h ffffh 0000h 0000h ffffh 0001h the user can select how many samples (1, 4, 8, or 16) to average for self or system offset calibration using the cal_samp[1:0] bits in the system control register (09h). fewer readings shorten the calibration time but also provide less accuracy. averaging more readings takes longer but yields a more accurate calibration result by reducing the noise level. two commands can be used to perform offset calibration. sfocal is a self offset calibration that internally sets the input to mid-scale using the sys_mon[2:0] = 001 setting and takes a measurement of the offset. syocal is a system offset calibration where the user must input a null voltage to calibrate the system offset. after either command is issued, the ofc register is updated. after an offset calibration is performed, the device starts a new conversion and drdy falls to indicate a new conversion has completed. 9.3.14.2 gain calibration the full-scale (gain) calibration word is 16 bits consisting of two 8-bit registers, as shown in the two registers starting with gain calibration register 1 . the gain calibration value is straight binary, normalized to a unity-gain correction factor at a register value equal to 4000h. table 22 shows register values for selected gain factors. do not exceed the pga input range limits during gain calibration. table 22. gain calibration register values fscal[1:0] register value gain factor 4333h 1.05 4000h 1.00 3ccch 0.95 all gains of the ads114s0x are factory trimmed to meet the gain error specified in the electrical characteristics table at t a = 25 c. when the gain drift of the devices over temperature is very low, there is typically no need for self gain calibration. the sygcal command initiates a system gain calibration, where the user sets the input to full-scale to remove gain error. after the sygcal is issued, the fsc register is updated. as with the offset calibration, the cal_samp[1:0] bits determine the number of samples used for a gain calibration. as with an offset calibration, the device starts a new conversion after a gain calibration and drdy falls to indicate a new conversion has completed. advance information 54 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.4 device functional modes the device operates in three different modes: power-down mode, standby mode, and conversion mode. figure 70 shows a flow chart of the different operating modes and how the device transitions from one mode to another. (1) any reset (power-on, command, or pin), immediately resets the device. (2) a powerdown command aborts an ongoing conversion and immediately puts the device into power-down mode. (3) the conversion mode is selected with the mode bit in the data rate register. (4) the rising edge of the start/sync pin or the start command starts a new conversion without completing the current conversion. figure 70. operating flow chart 9.4.1 reset the ads114s0x is reset in one of three ways: ? power-on reset ? reset pin ? reset command when a reset occurs, the configuration registers reset to default values and the device enters standby mode. the device then waits for the rising edge of the start/sync pin or a start command to enter conversion mode. note that if the device had been using an external clock, the reset sets the device to use the internal oscillator as a default configuration. see the timing characteristics section for reset timing information. power-on reset or reset pin high or reset command? (1) standby mode reset device to default settings start/sync rising edge or start command? conversion mode power-down mode (2) wakeup command? conversion mode selection (3) start new conversion 0 = continuous conversion mode 1 = single-shot conversion mode complete current conversion (4) start/sync pin low or stop command? no yes yes no no yes advance information 55 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated device functional modes (continued) 9.4.1.1 power-on reset the ads114s0x incorporates a power-on reset circuit that holds the device in reset until all supplies reach approximately 1.65 v. the power-on reset also ensures that the device starts operating in a known state in case a brown-out event occurs, when the supplies have dipped below the minimum operating voltages. when the device completes a por sequence, the fl_por flag in the status register is set high to indicate that a por has occurred. begin communications with the device 2.2 ms after the power supplies reach minimum operating voltages. the only exception is polling the status register for the rdy bit. if the user polls the rdy bit, then use an sclk rate of half the maximum-specified sclk rate to get a proper reading when the device is making internal configurations. this 2.2-ms por time is required for the internal oscillator to start up and the device to properly set internal configurations. after the internal configurations are set, the device sets the rdy bit in the device status register (01h). when this bit is set to 0, user configurations can be programmed into the device. figure 71 shows the power-on reset timing sequence for the device. figure 71. power-on reset timing sequence 9.4.1.2 reset pin reset the adc by taking the reset pin low for a minimum of 4 t clk cycles, and then returning the pin high. after the rising edge of the reset pin, a delay time of t d(rssc) is required before sending the first serial interface command or starting a conversion. see the timing characteristics section for reset timing information. 9.4.1.3 reset by command reset the adc by using the reset command (06h or 07h). the command is decoded on the seventh sclk falling edge. after sending the reset command, a delay time of t d(rssc) is required before sending the first serial interface command or starting a conversion. see the timing characteristics section for reset timing information. 9.4.2 power-down mode power-down mode is entered by sending the powerdown command. in this mode, all analog and digital circuitry is powered down for lowest power consumption regardless of the register settings. only the internal voltage reference can be configured to stay on during power-down mode in case a faster start-up time is required. all register values retain the current settings during power-down mode. the configuration registers can be read and written in power-down mode. a wakeup command must be issued in order to exit power-down mode and to enter standby mode. when the powerdown command is issued, the device enters power-down mode 2 t clk after the seventh sclk falling edge of the command. for lowest power consumption (on dvdd and iovdd), stop the external clock when in power-down mode. the device does not gate the external clock when in power-down mode. selecting the internal oscillator before sending the powerdown command is recommended. advance information dvdd, iovdd avdd - avss v por v por standby mode fl_por bit of status register is set to 1 internal oscillator startup internal configuration all supplies reach minimum operating voltage rdy bit of status register is set to 0 2.2 ms if polling for rdy during this period, sclk must be less than half maximum rate 56 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated device functional modes (continued) to release the device from powerdown, issue the wakeup command to enter standby mode. the device then waits for the rising edge of the start/sync pin or a start command to go into conversion mode. when in power-down mode, the device responds to the rreg, rdata, and wakeup commands. the wreg and reset commands can also be sent, but are ignored until a wakeup command is sent and the internal oscillator resumes operation. 9.4.3 standby mode the device powers up in standby mode and automatically enters this mode whenever there is no ongoing conversion. when the stop command is sent (or the start/sync pin is taken low) in continuous conversion mode, or when a conversion completes in single-shot conversion mode, the device enters standby mode. standby mode offers several different options and features to lower the power consumption: ? the pga can be powered down by setting pga_en[1:0] to 00 in the gain setting register (03h). ? the internal voltage reference can be powered down by setting refcon[1:0] to 00 in the reference control register (05h). this setting also turns off the idacs. ? the digital filter is held in reset state. ? the clock to the modulator and digital core is gated to decrease dynamic switching losses. if powered down in standby mode, the pga and internal reference can require extra time to power up. extra delay may be required between power up of the pga or the internal reference, and the start of conversions. in particular, the reference power up time is dependent on the capacitance between refout and refcom. calibration commands are not decoded when the device is in standby mode. 9.4.4 conversion modes the ads114s0x offers two conversion modes: continuous conversion and single-shot conversion mode. continuous-conversion mode converts indefinitely until stopped by the user. single-shot conversion mode performs one conversion after the start/sync pin is taken high or after the start command is sent. use the mode bit in the data rate register (04h) to program the conversion mode. figure 72 shows how the start/sync pin and the start command are used to control adc conversions. (1) drdy rises at the first sclk rising edge or the rising edge of the start/sync pin. (2) start and stop commands take effect 2 t clk after the seventh sclk falling edge. the conversion starts 2 t clk after the start/sync rising edge. (3) to synchronize a conversion, the stop command must be issued prior to the start command. stop and start commands can be issued without a delay between the commands. figure 72. conversion start and stop timing sclk din drdy start/sync pin start stop start command (2) (2) standby mode standby mode conversion mode (3) (1) advance information 57 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated device functional modes (continued) adc conversions are controlled by the start/sync pin or by serial commands. for the device to start converting in continuous conversion or single-shot conversion mode, a start command must be sent or the start/sync pin must be taken high. if using commands to control conversions, keep the start/sync pin low to avoid possible contentions between the start/sync pin and commands. conversions can be synchronized to perform a conversion at a particular time. to synchronize the conversion with the start/sync pin, take the pin low. the rising edge of the start/sync pin starts a new conversion. similarly, a conversion can be synchronized using the start command. if the device is in standby mode, issue a start command. if the device is in conversion mode, issue a stop command followed by a start command. the stop and start commands can be consecutive. a new conversion starts on the seventh sclk falling edge of the start command. 9.4.4.1 continuous conversion mode the device is configured for continuous conversion mode by setting the mode bit to 0 in the data rate register (04h). a start command must be sent or the start/sync pin must be taken high for the device to start converting continuously. when controlling the device with commands, hold the start/sync pin low. taking the start/sync pin low or sending the stop command stops the device from converting after the currently ongoing conversion completes, indicated by the falling edge of drdy. the device enters standby mode thereafter. for information on the exact timing of single-shot conversion mode data, see table 13 and table 15 . 9.4.4.2 single-shot conversion mode the device is configured for single-shot conversion mode by setting the mode bit to 1 in the data rate register (04h). a start command must be sent or the start/sync pin must be taken high for the device to start a single conversion. after the conversion completes, the device enters standby mode again. to start a new conversion, the start command must be sent again or the start/sync pin must be taken low and then high again. when the device uses the sinc 3 filter, adc data requires three conversion cycles to settle. when the sinc 3 filter is enabled, a single-shot conversion suppresses the first two adc conversions and provides the third conversion as the output data so that the user receives settled data. because three conversions are required for settled data, the conversion time in single-shot conversion mode is approximately three times the normal data period. when the device uses the low-latency filter, the adc data settles in a single conversion. in single-shot conversion mode with the low-latency filter, the data period is closer to the normal data period. for information on the exact timing of single-shot conversion mode data, see table 13 and table 15 . 9.4.4.3 programmable conversion delay when a new conversion is started, the adc provides a delay before the actual start of the conversion. this timed delay is provided to allow for the integrated analog anti-alias filter to settle. in some cases more delay is required to allow for external settling effects. the delay time can be configured to automatically delay the start of a conversion after a start command is sent, the start/sync pin is taken high, or a wreg command is sent to change any configuration register from address 03h to 07h is issued (as described in the wreg section). the programmable conversion delay is intended to accommodate the analog settling time on the inputs (for example, when changing a multiplexer channel). use the delay[2:0] bits in the gain setting register (03h) to program a delay time ranging from 1 t mod to 4096 t mod (where t mod = 16 t clk ). the default programmable conversion delay setting is 14 t mod . advance information 58 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5 programming 9.5.1 serial interface the adc has an spi-compatible, bidirectional serial interface that is used to read the conversion data as well as to configure and control the adc. only spi mode 1 (cpol = 0, cpha = 1) is supported. the serial interface consists of five control lines: cs, sclk, din, dout/ drdy, and drdy but can be used with only four or even three control signals. if the ads114s08 or ads114s06 is the only device connected to the spi bus, then the cs input can be tied low so that only sclk, din, and dout/ drdy are required to communicate with the device. 9.5.1.1 chip select ( cs) the cs pin is an active low input that enables the adc serial interface for communication and is useful when multiple devices share the same serial bus. cs must be low during the entire data transaction. when cs is high, the serial interface is reset, sclk input activity is ignored (blocking input commands), and the dout/ drdy output enters a high-impedance state. adc conversions are not affected by the state of cs. in situations where multiple devices are present on the bus, the dedicated drdy pin can provide an uninterrupted monitor of the conversion status and is not affected by cs. if the serial bus is not shared with another peripheral, cs can be tied to dgnd to permanently enable the adc interface and dout/ drdy can be used to indicate conversion status. these changes reduce the serial interface from five i/os to three i/os. 9.5.1.2 serial clock (sclk) the serial interface clock is a noise-filtered, schmidt-triggered input used to clock data into and out of the adc. input data to the adc are latched on the falling sclk edge and output data from the adc are updated on the rising sclk edge. return sclk low after the data sequence is complete. even though the sclk input has hysteresis, keep sclk as clean as possible to prevent unintentional sclk transitions. avoid ringing and voltage overshoot on the sclk input. place a series termination resistor at the sclk drive pin to help reduce ringing. 9.5.1.3 serial data input (din) the serial data input pin (din) is used with sclk to send data (commands and register data) to the device. the device latches data on din on the sclk falling edge. the device never drives the din pin. during data readback, when no command is intended, keep din low. 9.5.1.4 serial data output and data ready (dout/ drdy) the dout/ drdy pin is a dual-function output. the pin functions as the digital data output and the adc data- ready indication. first, this pin is used with sclk to read conversion and register data from the device. conversion or register data are shifted out on dout/ drdy on the sclk rising edge. dout/ drdy goes to a high-impedance state when cs is high. second, the dout/ drdy pin indicates availability of new conversion data. dout/ drdy transitions low at the same time that the drdy pin goes low to indicate new conversion data are available. both signals can be used to detect if new data are ready. however, because dout/ drdy is disabled when cs is high, use the dedicated drdy pin when monitoring conversions on multiple devices on the spi bus. advance information 59 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated programming (continued) 9.5.1.5 data ready ( drdy) the drdy pin is an output that transitions low to indicate when conversion data are ready for retrieval. initially, drdy is high at power-on. when converting, the state of drdy depends on whether the conversion data are retrieved or not. in continuous conversion mode after drdy goes low, drdy is driven high on the first sclk rising edge. if data are not read, drdy remains low and then pulses high 24 t clk before the next drdy falling edge. the data must be retrieved before the next drdy update, otherwise the data are overwritten by new data and any previous data are lost. figure 73 shows the drdy operation without data retrieval. figure 74 shows the drdy operation with data retrieval after each conversion completes. (1) drdy returns high with the rising edge of the first sclk after a data ready indication. figure 73. drdy operation without data retrieval (1) drdy returns high with the rising edge of the first sclk after a data ready indication. figure 74. drdy operation with data retrieval 9.5.1.6 timeout the ads114s0x offers a serial interface timeout feature that is used to recover communication when a serial interface transmission is interrupted. this feature is especially useful in applications where cs is permanently tied low and is not used to frame a communication sequence. the spi interface resets when no valid 8 bits are received within 2 15 t clk . the timeout feature is enabled by setting the timeout bit to 1 in the system control register (09h). advance information sclk din drdy start/sync pin start start command (1) dout/drdy conversion data 1 conversion data 2 conversion data 3 sclk din drdy start/sync pin start start command 60 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated programming (continued) 9.5.2 data format the devices provide 16 bits of data in binary twos complement format. the size of one code (lsb) is calculated using equation 11 . 1 lsb = (2 v ref / gain) / 2 16 = +fs / 2 15 (11) a positive full-scale input [v in (+fs ? 1 lsb) = (v ref / gain ? 1 lsb)] produces an output code of 7fffh and a negative full-scale input (v in ? fs = ? v ref / gain) produces an output code of 8000h. the output clips at these codes for signals that exceed full-scale. table 23 summarizes the ideal output codes for different input signals. (1) excludes the effects of noise, inl, offset, and gain errors. table 23. ideal output code vs input signal input signal, v in = v ainp ? v ainn ideal output code (1) fs (2 15 ? 1) / 2 15 7fffh fs / 2 15 0001h 0 0000h ? fs / 2 15 ffffh ? fs 8000h mapping of the analog input signal to the output codes is shown in figure 75 . figure 75. code transition diagram advance information 7fffh output code - fs ? 0 ? fs input voltage (v ) in 7ffeh 0001h ? 0000h8000h ffffh 8001h ? - fs 2 - 1 15 2 15 fs 2 - 1 15 2 15 61 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) x = don ' t care. (2) r rrrr = starting register address. (3) n nnnn = number of registers to read or write ? 1. 9.5.3 commands commands are used to control the adc, access the configuration registers, and retrieve data. many of the commands are stand-alone (that is, single-byte). the register write and register read commands, however, are multibyte, consisting of two command bytes plus the register data byte or bytes. the commands are listed in table 24 . table 24. command definitions command description first command byte second command byte control commands nop no operation 0000 0000 (00h) ? wakeup wake-up from power-down mode 0000 001x (02h, 03h) (1) ? powerdown enter power-down mode 0000 010x (04h, 05h) (1) ? reset reset the device 0000 011x (06h, 07h) (1) ? start start conversions 0000 100x (08h, 09h) (1) ? stop stop conversions 0000 101x (0ah, 0bh) (1) ? calibration commands syocal system offset calibration 0001 0110 (16h) ? sygcal system gain calibration 0001 0111 (17h) ? sfocal self offset calibration 0001 1001 (19h) ? data read command rdata read data by command 0001 001x (12h / 13h) (1) ? register read and write commands rreg read nnnnn registers starting at address rrrrr 001r rrrr (2) 000n nnnn (3) wreg write nnnnn registers starting at address rrrrr 010r rrrr (2) 000n nnnn (3) commands can be sent at any time, either during a conversion or when conversions are stopped. however, if register read or write commands are in progress when conversion data are ready, the adc blocks loading of conversion data to the output shift register. the cs input pin can be taken high between commands; or held low between consecutive commands. cs must stay low for the entire command sequence. complete the command, or terminate the command before completion by taking cs high. only send the commands that are listed in table 24 . 9.5.3.1 nop nop is a no-operation command. the nop command is used to clock out data without clocking in a command. 9.5.3.2 wakeup issue the wakeup command to exit power-down mode and to place the device into standby mode. when running off the external clock, the external clock must be running before sending the wakeup command, otherwise the command is not decoded. advance information 62 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.3.3 powerdown sending the powerdown command aborts a currently ongoing conversion and puts the device into power- down mode. the device goes into power-down mode 2 t clk after the seventh sclk falling edge of the command. for lowest power consumption on dvdd and iovdd, stop the external clock when in power-down mode. the device does not gate the external clock. when running off the external clock, provide at a minimum two additional t clk s after the powerdown command is issued, otherwise the device does not enter power-down mode. because an external clock can be gated for lower power consumption, selecting the internal oscillator before sending the powerdown command is recommended. during power-down mode, the only commands that are available are rreg, rdata, and wakeup. 9.5.3.4 reset the reset command resets the digital filter and sets all configuration register values to default settings. a reset command also puts the device into standby mode. when in standby mode, the device waits for a rising edge on the start/sync pin or a start command to resume conversions. after sending the reset command, a delay time of t d(rssc) is required before sending the first serial interface command or starting a conversion. see the timing characteristics section for reset timing information. note that if the device had been using an external clock, the reset sets the device to use the internal oscillator as a default configuration. 9.5.3.5 start when the device is configured for continuous conversion mode, issue the start command for the device to start converting. every time a conversion completes, the device automatically starts a new conversion until the stop command is sent. in single-shot conversion mode, the start command is used to start a single conversion. after the conversion completes, the device enters standby mode. tie the start/sync pin low when the device is controlled through the start and stop commands. the start command is not decoded if the start/sync pin is high. if the device is already in conversion mode, the command has no effect. 9.5.3.6 stop the stop command is used in continuous conversion mode to stop the device from converting. the current conversion is allowed to complete. after drdy transitions low, the device enters standby mode. the command has no effect in single-shot conversion mode. hold the start/sync pin low when the device is controlled through start and stop commands. 9.5.3.7 syocal the syocal command initiates a system offset calibration. for a system offset calibration, the inputs must be externally shorted to a voltage within the input range, ideally near the mid-supply voltage of (avdd + avss) / 2. the ofc registers are updated when the command completes. calibration commands must be issued in conversion mode. 9.5.3.8 sygcal the sygcal command initiates the system gain calibration. for a system gain calibration, the input must be externally set to full-scale. the fsc registers are updated after this operation. calibration commands must be issued in conversion mode. 9.5.3.9 sfocal the sfocal command initiates a self offset calibration. the device internally shorts the inputs to mid-supply and performs the calibration. the ofc registers are updated after this operation. calibration commands must be issued in conversion mode. advance information 63 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.3.10 rdata the rdata command is used to read conversion data from the device at any time without concern of data corruption when the drdy or dout/ drdy signal cannot be monitored. the conversion result is read from a buffer so that a new data conversion does not corrupt the conversion read. 9.5.3.11 rreg use the rreg command to read the device register data. read the register data one register at a time, or read a block of register data. the starting register address can be any register in the register map. the rreg command consists of two bytes. the first byte specifies the starting register address: 001r rrrr, where r rrrr is the starting register address. the second command byte is the number of registers to read (minus 1): 000n nnnn, where n nnnn is the number of registers to read minus 1. after the read command is sent, the adc responds with one or more register data bytes, most significant bit first. if the byte count exceeds the last register address, the adc begins to output zero data. during the register read operation, any conversion data that becomes available is not loaded to the output shift register to avoid data contention. however, the conversion data can be retrieved later by the rdata command. after the register read command has started, further commands are blocked until one of the following conditions are met: ? the read operation is completed ? the read operation is terminated by taking cs high ? the read operation is terminated by a serial interface timeout ? the adc is reset by toggling the reset pin figure 76 depicts a two-register read operation example. as shown, the commands required to read data from two registers starting at register ref (address = 05h) are: command byte 1 = 25h and command byte 2 = 01h. keep din low after the two command bytes are sent. (1) cs can be set high or kept low between commands. if kept low, the command must be completed. figure 76. read register sequence cs 1 sclk 9 17 25 dout/drdy din 0010 0101 0000 0001 reg data 1 reg data 2 '21?7&$5( '21?7&$5( (1) advance information 64 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.3.12 wreg use the wreg command to write the device register data. the register data are written one register at a time or as a block of register data. the starting register address is any register in the register map. the wreg command consists of two bytes. the first byte specifies the starting register address: 010r rrrr, where r rrrr is the starting register address the second command byte is the number of registers to write (minus 1): 000n nnnn, where n nnnn is the number of registers to write minus 1. the following byte (or bytes) is the register data, most significant bit first. if the byte count exceeds the last register address, the adc ignores the data. after the register write command has started, further commands are blocked until one of the following conditions are met: ? the write operation is completed ? the write operation is terminated by taking cs high ? the write operation is terminated by a serial interface timeout ? the adc is reset by toggling the reset pin figure 77 depicts a two-register write operation example. as shown, the required commands to write data to two registers starting at register ref (address = 05h) are: command byte 1 = 45h and command byte 2 = 01h. (1) cs can be set high or kept low between commands. if kept low, the command must be completed. figure 77. write register sequence writing new data to certain configuration registers resets the digital filter and starts a new conversion if a conversion is in progress. writing to the following registers triggers a new conversion: ? channel configuration register (02h) ? gain setting register (03h) ? data rate register (04h) ? reference control register (05h), bits [5:0] ? excitation current register 1 (06h), bits [3:0] ? excitation current register 2 (07h) ? system control register (09h), bits [7:5] when the device is configured with wreg, the first data ready indication occurs after the new conversion completes with the new configuration settings. the previous conversion data are cleared at restart; therefore read the previous data before the register write operation. again, a wreg to these registers only starts a new conversion if a conversion is in progress. if the device is in standby mode, the device sets the configuration according to the wreg data, but does not start a conversion until the start/sync pin is taken high or a start command is issued. cs 1 sclk 9 17 25 dout/drdy din 0100 0101 0000 0001 '21?7&$5( '21?7&$5( (1) '21?7&$5( '21?7&$5( reg data 1 reg data 2 advance information 65 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.4 reading data adc data are read by two methods: read data direct or read data by command. the adc writes new conversion data to the output shift register and the internal data-holding register. data are read either from the output shift register (in direct mode) or read from the data-holding register (in command mode). reading data from the data- holding register (command mode) does not require synchronizing the start of data readback to drdy. 9.5.4.1 read data direct in this method of data retrieval, adc conversion data are shifted out directly from the output shift register. no command is necessary. read data direct requires that no serial activity occur from the falling edge of drdy to the readback, or the data are invalid. the serial interface is full duplex in the read data direct mode; meaning that commands are decoded during the data readback. if no command is intended, keep din low during readback. if an input command is sent during readback, the adc executes the command, and data corruption can result. synchronize the data readback to drdy or to dout/ drdy to make sure the data are read before the next drdy update, or the old data are overwritten with new data. as shown in figure 78 , the adc data field is 2, 3, or 4 bytes long. the data field consists of an optional status byte, three bytes of conversion data, and an optional crc byte. after all bytes are read, the data-byte sequence (including the status byte and crc byte, if selected) is repeated when continued sclks are sent. the byte sequence repeats starting with the first byte. in order to help verify error-free communication, read the same data multiple times in each conversion interval or use the optional crc byte. (1) drdy returns high on the first sclk falling edge. (2) cs can be tied low. if cs is low, dout/ drdy asserts low at the same time as drdy. (3) complete data retrieval before new data are ready (28 t clk before the next falling edge of dout/ drdy and drdy). (4) the status and crc bytes are optional. (5) the byte sequence, including selected optional bytes, repeats by continuing sclk. figure 78. read data direct advance information status data 1 adc data bytes optional (4) optional (4) din sclk cs hi-z drdy (3) (1) (2) repeat repeated data (5) dout/drdy data 2 crc 1 9 17 25 33 sendstat bit of sys register 0 = disabled 1 = enabled crc bit of sys register 0 = disabled 1 = enabled 66 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.4.2 read data by rdata command when the rdata command is sent, the data are retrieved from the adc data-holding register. read data at any time without the risk of data corruption because the command method does not require synchronizing to drdy. polling of drdy to determine when adc data are ready can still be used. figure 79 shows the read data by command sequence. the output data msb begins on the first sclk rising edge after the command. the output data field can be 2, 3, or 4 bytes long. the data field consists of an optional status byte, three bytes of conversion data, and an optional crc byte. an rdata command must be sent for each read operation. the adc does not respond to commands until the read operation is complete, or terminated by taking cs high. after all bytes are read, the data-byte sequence (including the status byte and crc byte, if selected) is repeated by continuing sclk. (1) cs can be tied low. if cs is low, dout/ drdy asserts low with drdy. (2) dout/ drdy is driven low with drdy. if a read operation occurs after the drdy falling edge, then dout/ drdy can be high or low. (3) the status and crc bytes are optional. figure 79. read data by command 'rq?w&duh status optional (3) optional (3) din sclk cs hi-z (1) dout/drdy data 1 data 2 crc 1 9 17 25 33 sendstat bit of sys register 0 = disabled 1 = enabled crc bit of sys register 0 = disabled 1 = enabled adc data bytes rdata (2) advance information 67 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.5.4.3 sending commands when reading data the device serial interface is capable of full-duplex operation when reading conversion data and not using the rdata command. in full-duplex operation, commands are decoded at the same time that conversion data are read. commands can be sent on any 8-bit data boundary during a data read operation. when a rreg or rdata command is recognized, the current data read operation is aborted and the conversion data are corrupted, unless the command is sent when the last byte of the conversion result is retrieved. the device starts to output the requested data on dout/ drdy at the first sclk rising edge after the command byte. to read data without interruption, keep din low when clocking out data. a wreg command can be sent without corrupting an ongoing read operation. sending a wreg command when reading data minimizes the time between reading the data and setting the device configuration for the next conversion. figure 80 shows an example for sending a wreg command to write two configuration registers when reading conversion data by using read data direct mode. after the command is clocked in, the device resets the digital filter and starts converting with the new register settings as long as the device is in continuous conversion mode. the digital filter is reset and conversions are restarted after each data byte is received. in this example, the digital filter is reset when the first byte is received, decoding the input multiplexer and again when the pga is set. the wreg command can be sent on any of the 8-bit boundaries. the example in figure 80 has the status and crc bytes disabled. (1) cs can be tied low. if cs is low, dout/ drdy asserts low at the same time as drdy. (2) the output data buffer is cyclical and the original data byte is re-issued when the fourth din byte is clocked in. figure 80. issuing a wreg command when reading back adc data 9.5.5 interfacing with multiple devices when connecting multiple devices to a single spi bus, sclk, din, and dout/ drdy can be safely shared by using a dedicated chip-select ( cs) line for each spi-enabled device. when cs transitions high for the respective device, dout/ drdy enters a tri-state mode. therefore, dout/ drdy cannot be used to indicate when new data are available if cs is high. only the dedicated drdy pin indicates that new data are available because the drdy pin is actively driven even when cs is high. in some cases, the drdy pin cannot be interfaced to the microcontroller. this scenario can occur if there are insufficient gpio channels available on the microcontroller or if the serial interface must be galvanically isolated and thus the amount of channels must be limited. in order to evaluate when a new conversion of one of the devices is ready, the microcontroller can periodically drop cs to the respective device and poll the state of the dout/ drdy pin. when cs goes low, the dout/ drdy pin immediately drives either high or low. if the dout/ drdy line drives low, new data are available. if the dout/ drdy line drives high, no new data are available. this procedure requires that dout/ drdy is forced high after reading each conversion result and before taking cs high. to make sure dout/ drdy is taken high, send a rreg command to read a register where the least significant bit is 1. advance information data 1 adc data bytes din sclk cs hi-z drdy (1) dout/drdy data 2 1 9 17 25 0100 0010 0000 0001 0011 0010 0000 1011 wreg at 02h two bytes ain p = ain3, ain n = ain2 pga enabled, gain = 8 repeat data 2 (2) repeat data 1 68 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated retrieving data using direct read mode requires knowledge of the drdy falling edge timing to avoid data corruption. use the rdata command so that valid data can be retrieved from the device at any time without concern of data corruption by a new data ready. 9.6 register map 9.6.1 configuration registers the ads114s0x register map consists of 18, 8-bit registers. these registers are used to configure and control the device to the desired mode of operation. access the registers through the serial interface by using the rreg and wreg register commands. after power-on or reset, the registers default to the initial settings, as shown in the default column of table 25 . data can be written as a block to multiple registers using a single wreg command. if data are written as a block, the data of certain registers take effect immediately when data are shifted in. writing new data to certain registers results in a restart of conversions that are in progress. the registers that result in a conversion restart are discussed in the wreg section. table 25. configuration register map addr register default bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 00h id xxh reserved dev_id[2:0] 01h status 80h fl_por rdy fl_p_railp fl_p_railn fl_n_railp fl_n_railn fl_ref_l1 fl_ref_l0 02h inpmux 01h muxp[3:0] muxn[3:0] 03h pga 00h delay[2:0] pga_en[1:0] gain[2:0] 04h datarate 14h g_chop clk mode filter dr[3:0] 05h ref 10h fl_ref_en[1:0] refp_buf refn_buf refsel[1:0] refcon[1:0] 06h idacmag 00h fl_rail_en psw 0 0 imag[3:0] 07h idacmux ffh i2mux[3:0] i1mux[3:0] 08h vbias 00h vb_level vb_ainc vb_ain5 vb_ain4 vb_ain3 vb_ain2 vb_ain1 vb_ain0 09h sys 10h sys_mon[2:0] cal_samp[1:0] timeout crc sendstat 0ah reserved 00h reserved[7:0] 0bh ofcal0 00h ofc[7:0] 0ch ofcal1 00h ofc[15:8] 0dh reserved 00h reserved[7:0] 0eh fscal0 00h fsc[7:0] 0fh fscal1 40h fsc[15:8] 10h gpiodat 00h dir[3:0] dat[3:0] 11h gpiocon 00h 0 0 0 0 con[3:0] advance information 69 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.1 device id register (address = 00h) [reset = xxh] figure 81. device id (id) register 7 6 5 4 3 2 1 0 reserved dev_id[2:0] r-xxh r-xh legend: r = read only; -n = value after reset; -x = variable table 26. device id (id) register field descriptions bit field type reset description 7:3 reserved r xxh reserved values are subject to change without notice. 2:0 dev_id[2:0] r xh device identifier identifies the model of the device. 000 : reserved 001 : reserved 010 : reserved 011 : reserved 100 : ads114s08 (12 channels, 16 bits) 101 : ads114s06 (6 channels, 16 bits) 110 : reserved 111 : reserved advance information 70 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.2 device status register (address = 01h) [reset = 80h] figure 82. device status (status) register 7 6 5 4 3 2 1 0 fl_por rdy fl_p_railp fl_p_railn fl_n_railp fl_n_railn fl_ref_l1 fl_ref_l0 r/w-1h r-0h r-0h r-0h r-0h r-0h r-0h r-0h legend: r/w = read/write; r = read only; - n = value after reset (1) the pga rail monitors are enabled with the fl_rail_en bit in excitation current register 1 (06h). (2) the reference monitors are enabled with the fl_ref_en[1:0] bits of the reference control register (05h). table 27. device status (status) register field descriptions bit field type reset description 7 fl_por r/w 1h por flag indicates a power-on reset (por) event has occurred. 0 : register has been cleared and no por event has occurred. 1 : por event occurred and has not been cleared. flag must be cleared by user register write (default). 6 rdy r 0h device ready flag indicates the device has started up and is ready for communication. 0 : adc ready for communication (default) 1 : adc not ready 5 fl_p_railp r 0h positive pga output at positive rail flag (1) indicates the positive pga output is within 150 mv of avdd. 0 : no error (default) 1 : pga positive output within 150 mv of avdd 4 fl_p_railn r 0h positive pga output at negative rail flag (1) indicates the positive pga output is within 150 mv of avss. 0 : no error (default) 1 : pga positive output within 150 mv of avss 3 fl_n_railp r 0h negative pga output at positive rail flag (1) indicates the negative pga output is within 150 mv of avdd. 0 : no error (default) 1 : pga negative output within 150 mv of avdd 2 fl_n_railn r 0h negative pga output at negative rail flag (1) indicates the negative pga output is within 150 mv of avss. 0 : no error (default) 1 : pga negative output within 150 mv of avss 1 fl_ref_l1 r 0h reference voltage monitor flag, level 1 (2) indicates the external reference voltage is lower than 1/3 of the analog supply voltage. can be used to detect an open-excitation lead in a 3-wire rtd application. 0 : differential reference voltage 1/3 (avdd ? avss) (default) 1 : differential reference voltage < 1/3 (avdd ? avss) 0 fl_ref_l0 r 0h reference voltage monitor flag, level 0 (2) indicates the external reference voltage is lower than 0.3 v. can be used to indicate a missing or floating external reference voltage. 0 : differential reference voltage 0.3 v (default) 1 : differential reference voltage < 0.3 v advance information 71 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.3 input multiplexer register (address = 02h) [reset = 01h] figure 83. input multiplexer (inpmux) register 7 6 5 4 3 2 1 0 muxp[3:0] muxn[3:0] r/w-0h r/w-1h legend: r/w = read/write; - n = value after reset table 28. input multiplexer (inpmux) register field descriptions bit field type reset description 7:4 muxp[3:0] r/w 0h positive adc input selection selects the adc positive input channel. 0000 : ain0 (default) 0001 : ain1 0010 : ain2 0011 : ain3 0100 : ain4 0101 : ain5 0110 : ain6 (ads114s08 only) 0111 : ain7 (ads114s08 only) 1000 : ain8 (ads114s08 only) 1001 : ain9 (ads114s08 only) 1010 : ain10 (ads114s08 only) 1011 : ain11 (ads114s08 only) 1100 : aincom 1101 : reserved 1110 : reserved 1111 : reserved 3:0 muxn[3:0] r/w 1h negative adc input selection selects the adc negative input channel. 0000 : ain0 0001 : ain1 (default) 0010 : ain2 0011 : ain3 0100 : ain4 0101 : ain5 0110 : ain6 (ads114s08 only) 0111 : ain7 (ads114s08 only) 1000 : ain8 (ads114s08 only) 1001 : ain9 (ads114s08 only) 1010 : ain10 (ads114s08 only) 1011 : ain11 (ads114s08 only) 1100 : aincom 1101 : reserved 1110 : reserved 1111 : reserved advance information 72 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.4 gain setting register (address = 03h) [reset = 00h] figure 84. gain setting (pga) register 7 6 5 4 3 2 1 0 delay[2:0] pga_en[1:0] gain[2:0] r/w-0h r/w-0h r/w-0h legend: r/w = read/write; - n = value after reset (1) for details on which bits and registers trigger a new conversion, see the wreg section. (2) when bypassing the pga, the user must also set gain[2:0] to 000. table 29. gain setting (pga) register field descriptions bit field type reset description 7:5 delay[2:0] r/w 0h programmable conversion delay selection sets the programmable conversion delay time for the first conversion after a wreg when a configuration change resets of the digital filter and triggers a new conversion (1) . 000 : 14 t mod (default) 001 : 25 t mod 010 : 64 t mod 011 : 256 t mod 100 : 1024 t mod 101 : 2048 t mod 110 : 4096 t mod 111 : 1 t mod 4:3 pga_en[1:0] r/w 0h pga enable enables or bypasses the pga. 00 : pga is powered down and bypassed. enables single-ended measurements with unipolar supply (set gain = 1 (2) ) (default) 01 : pga enabled (gain = 1 to 128) 10 : reserved 11 : reserved 2:0 gain[2:0] r/w 0h pga gain selection configures the pga gain. 000 : 1 (default) 001 : 2 010 : 4 011 : 8 100 : 16 101 : 32 110 : 64 111 : 128 advance information 73 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.5 data rate register (address = 04h) [reset = 14h] figure 85. data rate (datarate) register 7 6 5 4 3 2 1 0 g_chop clk mode filter dr[3:0] r/w-0h r/w-0h r/w-0h r/w-1h r/w-4h legend: r/w = read/write; r = read only; - n = value after reset (1) data rates of 60 hz or less can offer line-cycle rejection; see the 50-hz and 60-hz line cycle rejection section for more information. table 30. data rate (datarate) register field descriptions bit field type reset description 7 g_chop r/w 0h global chop enable enables the global chop function. when enabled, the device automatically swaps the inputs and takes the average of two consecutive readings to cancel the offset voltage. 0 : disabled (default) 1 : enabled 6 clk r/w 0h clock source selection configures the clock source to use either the internal oscillator or an external clock. 0 : internal 4.096-mhz oscillator (default) 1 : external clock 5 mode r/w 0h conversion mode selection configures the adc for either continuous conversion or single-shot conversion mode. 0 : continuous conversion mode (default) 1 : single-shot conversion mode 4 filter r/w 1h digital filter selection configures the adc to use either the sinc 3 or the low-latency filter. 0 : sinc 3 filter 1 : low-latency filter (default) 3:0 dr[3:0] r/w 4h data rate selection configures the output data rate (1) . 0000 : 2.5 sps 0001 : 5 sps 0010 : 10 sps 0011 : 16.6 sps 0100 : 20 sps 0101 : 50sps 0110 : 60 sps 0111 : 100 sps 1000 : 200 sps 1001 : 400 sps 1010 : 800 sps 1011 : 1000 sps 1100 : 2000 sps 1101 : 4000 sps 1110 : 4000 sps 1111 : reserved advance information 74 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.6 reference control register (address = 05h) [reset = 10h] figure 86. reference control (ref) register 7 6 5 4 3 2 1 0 fl_ref_en[1:0] refp_buf refn_buf refsel[1:0] refcon[1:0] r/w-0h r/w-0h r/w-1h r/w-0h r/w-0h legend: r/w = read/write; - n = value after reset (1) disable the reference buffers when the internal reference is selected for measurements. (2) the internal voltage reference must be turned on to use the idacs. table 31. reference control (ref) register field descriptions bit field type reset description 7:6 fl_ref_en[1:0] r/w 0h reference monitor configuration enables and configures the reference monitor. 00 : disabled (default) 01 : fl_ref_l0 monitor enabled, threshold 0.3 v 10 : fl_ref_l0 and fl_ref_l1 monitors enabled, thresholds 0.3 v and 1/3 (avdd ? avss) 11 : fl_ref_l0 monitor and 10-m pull-together enabled, threshold 0.3 v 5 refp_buf r/w 0h positive reference buffer bypass disables the positive reference buffer. recommended when v (refpx) is close to avdd. 0 : enabled (default) 1 : disabled 4 refn_buf r/w 1h negative reference buffer bypass disables the negative reference buffer. recommended when v (refnx) is close to avss. 0 : enabled 1 : disabled (default) 3:2 refsel[1:0] r/w 0h reference input selection selects the reference input source for the adc. 00 : refp0, refn0 (default) 01 : refp1, refn1 10 : internal 2.5-v reference (1) 11 : reserved 1:0 refcon[1:0] r/w 0h internal voltage reference configuration (2) configures the behavior of the internal voltage reference. 00 : internal reference off (default) 01 : internal reference on, but powers down in power-down mode 10 : internal reference is always on, even in power-down mode 11 : reserved advance information 75 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.7 excitation current register 1 (address = 06h) [reset = 00h] figure 87. excitation current register 1 (idacmag) 7 6 5 4 3 2 1 0 fl_rail_en psw 0 0 imag[3:0] r/w-0h r/w-0h r-0h r-0h r/w-0h legend: r/w = read/write; r = read only; - n = value after reset table 32. excitation current register 1 (idacmag) register field descriptions bit field type reset description 7 fl_rail_en r/w 0h pga output rail flag enable enables the pga output voltage rail monitor circuit. 0 : disabled (default) 1 : enabled 6 psw r/w 0h low-side power switch controls the low-side power switch. the low-side power switch opens automatically in power-down mode. 0 : open (default) 1 : closed 5:4 reserved r 0h reserved always write 0 3:0 imag[3:0] r/w 0h idac magnitude selection selects the value of the excitation current sources. sets idac1 and idac2 to the same value. 0000 : off (default) 0001 : 10 a 0010 : 50 a 0011 : 100 a 0100 : 250 a 0101 : 500 a 0110 : 750 a 0111 : 1000 a 1000 : 1500 a 1001 : 2000 a 1010 - 1111 : off advance information 76 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.8 excitation current register 2 (address = 07h) [reset = ffh] figure 88. excitation current register 2 (idacmux) 7 6 5 4 3 2 1 0 i2mux[3:0] i1mux[3:0] r/w-fh r/w-fh legend: r/w = read/write; - n = value after reset table 33. excitation current register 2 (idacmux) register field descriptions bit field type reset description 7:4 i2mux[3:0] r/w fh idac2 output channel selection selects the output channel for idac2. 0000 : ain0 0001 : ain1 0010 : ain2 0011 : ain3 0100 : ain4 0101 : ain5 0110 : ain6 (ads114s08), refp1 (ads114s06) 0111 : ain7 (ads114s08), refn1 (ads114s06) 1000 : ain8 (ads114s08 only) 1001 : ain9 (ads114s08 only) 1010 : ain10 (ads114s08 only) 1011 : ain11 (ads114s08 only) 1100 : aincom 1101 - 1111 : disconnected (default) 3:0 i1mux[3:0] r/w fh idac1 output channel selection selects the output channel for idac1. 0000 : ain0 0001 : ain1 0010 : ain2 0011 : ain3 0100 : ain4 0101 : ain5 0110 : ain6 (ads114s08 only), refp1 (ads114s06) 0111 : ain7 (ads114s08 only), refn1 (ads114s06) 1000 : ain8 (ads114s08 only) 1001 : ain9 (ads114s08 only) 1010 : ain10 (ads114s08 only) 1011 : ain11 (ads114s08 only) 1100 : aincom 1101 - 1111 : disconnected (default) advance information 77 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.9 sensor biasing register (address = 08h) [reset = 00h] figure 89. sensor biasing (vbias) register 7 6 5 4 3 2 1 0 vb_level vb_ainc vb_ain5 vb_ain4 vb_ain3 vb_ain2 vb_ain1 vb_ain0 r/w-0h r/w-0h r/w-0h r/w-0h r/w-0h r/w-0h r/w-0h r/w-0h legend: r/w = read/write; - n = value after reset (1) the bias voltage can be selected for multiple analog inputs at the same time. table 34. sensor biasing (vbias) register field descriptions bit field type reset description 7 vb_level r/w 0h vbias level selection sets the vbias output voltage level. vbias is disabled when not connected to any input. 0 : (avdd + avss) / 2 (default) 1 : (avdd + avss) / 12 6 vb_ainc r/w 0h aincom vbias selection (1) enables vbias on the aincom pin. 0 : vbias disconnected from aincom 1 : vbias connected to aincom 5 vb_ain5 r/w 0h ain5 vbias selection (1) enables vbias on the ain5 pin. 0 : vbias disconnected from ain5 1 : vbias connected to ain5 4 vb_ain4 r/w 0h ain4 vbias selection (1) enables vbias on the ain4 pin. 0 : vbias disconnected from ain4 1 : vbias connected to ain4 3 vb_ain3 r/w 0h ain3 vbias selection (1) enables vbias on the ain3 pin. 0 : vbias disconnected from ain3 1 : vbias connected to ain3 2 vb_ain2 r/w 0h ain2 vbias selection (1) enables vbias on the ain2 pin. 0 : vbias disconnected from ain2 1 : vbias connected to ain2 1 vb_ain1 r/w 0h ain1 vbias selection (1) enables vbias on the ain1 pin. 0 : vbias disconnected from ain1 1 : vbias connected to ain1 0 vb_ain0 r/w 0h ain0 vbias selection (1) enables vbias on the ain0 pin. 0 : vbias disconnected from ain0 1 : vbias connected to ain0 advance information 78 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.10 system control register (address = 09h) [reset = 10h] figure 90. system control (sys) register 7 6 5 4 3 2 1 0 sys_mon[2:0] cal_samp[1:0] timeout crc sendstat r/w-0h r/w-2h r/w-0h r/w-0h r/w-0h legend: r/w = read/write; - n = value after reset (1) with system monitor functions enabled, the ainx multiplexer switches are open for the (avdd + avss) / 2 measurement, the temperature sensor, and the supply monitors. (2) when using the internal temperature sensor, gain must be 4 or less to keep the measurement within the pga input voltage range. (3) the pga gain is automatically set to 1 when the supply monitors are enabled, regardless of the setting in gain[2:0]. table 35. system control (sys) register field descriptions bit field type reset description 7:5 sys_mon[2:0] r/w 0h system monitor configuration (1) enables a set of system monitor measurements using the adc. 000 : disabled (default) 001 : pga inputs shorted to (avdd + avss) / 2 and disconnected from ainx and the multiplexer; gain set by user 010 : internal temperature sensor measurement; pga must be enabled (pga_en[1:0] = 01); gain set by user (2) 011 : (avdd ? avss) / 4 measurement; gain set to 1 (3) 100 : dvdd / 4 measurement; gain set to 1 (3) 101 : burn-out current sources enabled, 0.2- a setting 110 : burn-out current sources enabled, 1- a setting 111 : burn-out current sources enabled, 10- a setting 4:3 cal_samp[1:0] r/w 2h calibration sample size selection configures the number of samples averaged for self and system offset and system gain calibration. 00 : 1 sample 01 : 4 samples 10 : 8 samples (default) 11 : 16 samples 2 timeout r/w 0h spi timeout enable enables the spi timeout function. 0 : disabled (default) 1 : enabled 1 crc r/w 0h crc enable enables the crc byte appended to the conversion result. when enabled, crc is calculated across the 16-bit conversion result (plus the status byte if enabled). 0 : disabled (default) 1 : enabled 0 sendstat r/w 0h status byte enable enables the status byte prepended to the conversion result. 0 : disabled (default) 1 : enabled advance information 79 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.11 reserved register (address = 0ah) [reset = 00h] figure 91. reserved register 7 6 5 4 3 2 1 0 reserved[7:0] r-00h legend: r/w = read/write; - n = value after reset table 36. reserved register field descriptions bit field type reset description 7:0 reserved[7:0] r 00h reserved always write 0 9.6.1.12 offset calibration register 1 (address = 0bh) [reset = 00h] figure 92. offset calibration register 1 (ofcal 0) 7 6 5 4 3 2 1 0 ofc [7:0] r/w-00h legend: r/w = read/write; - n = value after reset table 37. offset calibration register 1 (ofcal 0) register field descriptions bit field type reset description 7:0 ofc [7:0] r/w 00h bits [7:0] of the offset calibration value. 9.6.1.13 offset calibration register 2 (address = 0ch) [reset = 00h] figure 93. offset calibration register 2 (ofcal 1) 7 6 5 4 3 2 1 0 ofc [15:8] r/w-00h legend: r/w = read/write; - n = value after reset table 38. offset calibration register 2 (ofcal 1) register field descriptions bit field type reset description 7:0 ofc [15:8] r/w 00h bits [15:8] of the offset calibration value. advance information 80 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.14 reserved register (address = 0dh) [reset = 00h] figure 94. reserved register 7 6 5 4 3 2 1 0 reserved[7:0] r-00h legend: r/w = read/write; - n = value after reset table 39. reserved register field descriptions bit field type reset description 7:0 reserved[7:0] r 00h reserved always write 0. 9.6.1.15 gain calibration register 1 (address = 0eh) [reset = 00h] figure 95. gain calibration register 1 (fscal 0) 7 6 5 4 3 2 1 0 fsc [7:0] r/w-00h legend: r/w = read/write; - n = value after reset table 40. gain calibration register 1 (fscal 0) field descriptions bit field type reset description 7:0 fsc [7:0] r/w 00h bits [7:0] of the gain calibration value. 9.6.1.16 gain calibration register 2 (address = 0fh) [reset = 40h] figure 96. gain calibration register 2 (fscal 1) 7 6 5 4 3 2 1 0 fsc [15:8] r/w-40h legend: r/w = read/write; - n = value after reset table 41. gain calibration register 2 (fscal 1) field descriptions bit field type reset description 7:0 fsc [15:8] r/w 40h bits [15:8] of the gain calibration value. advance information 81 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 9.6.1.17 gpio data register (address = 10h) [reset = 00h] figure 97. gpio data (gpiodat) register 7 6 5 4 3 2 1 0 dir[3:0] dat[3:0] r/w-0h r/w-0h legend: r/w = read/write; - n = value after reset table 42. gpio data (gpiodat) register field descriptions bit field type reset description 7:4 dir[3:0] r/w 0h gpio direction configures the selected gpio as an input or output. 0 : gpio[x] configured as output (default) 1 : gpio[x] configured as input 3:0 dat[3:0] r/w 0h gpio data contains the data of the gpio inputs or outputs. 0 : gpio[x] is low (default) 1 : gpio[x] is high 9.6.1.18 gpio configuration register (address = 11h) [reset = 00h] figure 98. gpio configuration register 7 6 5 4 3 2 1 0 0 0 0 0 con[3:0] r-0h r-0h r-0h r-0h r/w-0h legend: r/w = read/write; r = read only; - n = value after reset (1) on the ads114s06, the gpio pins default as disabled. set the con[3:0] bits to enable the respective gpio pins. table 43. gpio configuration (gpiocon) register field descriptions bit field type reset description 7:4 reserved r 0h always write 0 3:0 con[3:0] r/w 0h gpio pin configuration configures the gpio[x] pin as an analog input or gpio. con[x] corresponds to the gpio[x] pin. 0 : gpio[x] configured as analog input (default) (1) 1 : gpio[x] configured as gpio advance information 82 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 10 application and implementation note information in the following applications sections is not part of the ti component specification, and ti does not warrant its accuracy or completeness. ti ? s customers are responsible for determining suitability of components for their purposes. customers should validate and test their design implementation to confirm system functionality. 10.1 application information the ads114s06 and ads114s08 are precision, 16-bit, adcs that offer many integrated features to simplify the measurement of the most common sensor types (including various types of temperature, flow, and bridge sensors). primary considerations when designing an application with the ads114s0x include analog input filtering, establishing an appropriate reference, and setting the absolute input voltage for the internal pga. connecting and configuring the serial interface appropriately is another concern. these considerations are discussed in the following sections. 10.1.1 serial interface connections the principle serial interface connections for the ads114s0x are shown in figure 99 . figure 99. serial interface connections most microcontroller spi peripherals can interface with the ads114s0x. the interface operates in spi mode 1 where cpol = 0 and cpha = 1. in spi mode 1, sclk idles low and data are launched or changed only on sclk rising edges; data are latched or read by the master and slave on sclk falling edges. details of the spi communication protocol employed by the devices are found in the serial interface section. place 47- resistors in series with all digital input and output pins ( cs, sclk, din, dout/ drdy, and drdy). this resistance smooths sharp transitions, suppresses overshoot, and offers some overvoltage protection. care must be taken to meet all spi timing requirements because the additional resistors interact with the bus capacitances present on the digital signal lines. 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 aincom ain5 ain4 ain3 ain2 ain1 ain0 start/sync cs din sclk dout/drdy drdy dgnd iovdd dvdd clk reset gpio3/ain11 gpio2/ain10 gpio1/ain9 gpio0/ain8 refout refcom nc avdd avss avss-sw refn0 refp0 refn1/ain7 refp1/ain6 47 47 47 47 47 47 47 gpio gpio miso gpio/irq gpio mosi microcontroller with spi dvdd dvss 0.1 p f 3.3 v sclk 330 nf 5 v 3.3 v 0.1 p f 1 p f advance information 83 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated application information (continued) 10.1.2 analog input filtering analog input filtering serves two purposes: first, to limit the effect of aliasing during the sampling process and second, to reduce external noise from being a part of the measurement. as with any sampled system, aliasing can occur if proper antialias filtering is not in place. aliasing occurs when frequency components are present in the input signal that are higher than half the sampling frequency of the adc (also known as the nyquist frequency). these frequency components are folded back and show up in the actual frequency band of interest below half the sampling frequency. note that inside a adc, the input signal is oversampled at the modulator frequency, f mod and not at the output data rate. the filter response of the digital filter repeats at multiples of f mod , as shown in figure 100 . signals or noise up to a frequency where the filter response repeats are attenuated to a certain amount by the digital filter depending on the filter architecture. any frequency components present in the input signal around the modulator frequency or multiples thereof are not attenuated and alias back into the band of interest, unless attenuated by an external analog filter. figure 100. effect of aliasing advance information magnitude f mod /2 f mod output data rate frequency external antialiasing filter roll-off magnitude f mod /2 f mod output data rate frequency digital filter magnitude f mod /2 f mod output data rate frequency sensor signal unwanted signals unwanted signals aliasing of unwanted signals 84 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated application information (continued) many sensor signals are inherently band limited; for example, the output of a thermocouple has a limited rate of change. in this case, the sensor signal does not alias back into the pass band when using a adc. however, any noise pick-up along the sensor wiring or the application circuitry can potentially alias into the pass band. power line-cycle frequency and harmonics are one common noise source. external noise can also be generated from electromagnetic interference (emi) or radio frequency interference (rfi) sources, such as nearby motors and cellular phones. another noise source typically exists on the printed circuit board (pcb) itself in the form of clocks and other digital signals. analog input filtering helps remove unwanted signals from affecting the measurement result. a first-order resistor-capacitor (rc) filter is (in most cases) sufficient to either eliminate aliasing, or to reduce the effect of aliasing to a level below the noise floor of the sensor. ideally, any signal beyond f mod / 2 is attenuated to a level below the noise floor of the adc. the digital filter of the ads114s0x attenuates signals to a certain degree, as illustrated in the filter response plots in the digital filter section. in addition, noise components are usually smaller in magnitude than the actual sensor signal. therefore, using a first-order rc filter with a cutoff frequency set at the output data rate or 10 times higher is generally a good starting point for a system design. internal to the device, prior to the pga inputs, is an emi filter; see figure 38 . the cutoff frequency of this filter is approximately 40 mhz and helps reject high-frequency interference. 10.1.3 external reference and ratiometric measurements the full-scale range of the ads114s0x is defined by the reference voltage and the pga gain (fsr = v ref / gain). an external reference can be used instead of the integrated 2.5-v reference to adapt the fsr to the specific system needs. an external reference must be used if v in > 2.5 v. for example, an external 5- v reference and an avdd = 5 v are required in order to measure a single-ended signal that can swing between 0 v and 5 v. the reference inputs of the device also allow the implementation of ratiometric measurements. in a ratiometric measurement, the same excitation source that is used to excite the sensor is also used to establish the reference for the adc. as an example, a simple form of a ratiometric measurement uses the same current source to excite both the resistive sensor element (such as an rtd) and another resistive reference element that is in series with the element being measured. the voltage that develops across the reference element is used as the reference source for the adc. because current noise and drift are common to both the sensor measurement and the reference, these components cancel out in the adc transfer function. the output code is only a ratio of the sensor element and the value of the reference resistor. the value of the excitation current source itself is not part of the adc transfer function. the example in the typical application section describes a system that uses a ratiometric measurement. one excitation current source is used to drive a reference resistor and an rtd. the adc measurement represents a ratiometric measurement between the rtd value and a known reference resistor value. 10.1.4 establishing a proper input voltage the ads114s0x can be used to measure various types of input signal configurations: single-ended, pseudo- differential, and fully-differential signals (which can be either unipolar or bipolar). however, configuring the device properly for the respective signal type is important. signals where the negative analog input is fixed and referenced to analog ground (v ainn = 0 v) are commonly called single-ended signals . the input voltage of a single-ended signal consequently varies between 0 v and v in . if the pga is disabled and bypassed, the input voltage of the ads114s08 can be as low as 50 mv below avss and as large as 50 mv above avdd. therefore, set the pga_en bits to 10 in the gain setting register (03h) to measure single-ended signals when a unipolar analog supply is used (avss = 0 v). only a gain of 1 is possible in this configuration. measuring a 0-ma to 20-ma or 4-ma to 20-ma signal across a load resistor of 100 referenced to gnd is a typical example. the ads114s0x can directly measure the signal across the load resistor using a unipolar supply, the internal 2.5-v reference, and gain = 1 when the pga is bypassed. if gain is needed to measure a single-ended signal, the pga must be enabled. in this case, a bipolar supply is required for the ads114s0x to meet the input voltage requirement of the pga. signals where the negative analog input (ain n ) is fixed at a voltage other the 0 v are referred to as pseudo-differential signals . the input voltage of a pseudo-differential signal varies between v ainn and v ainn + v in . advance information 85 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated application information (continued) fully-differential signals in contrast are defined as signals having a constant common-mode voltage where the positive and negative analog inputs swing 180 out-of-phase but have the same amplitude. the ads114s0x can measure pseudo-differential and fully-differential signals both with the pga enabled or bypassed. however, the pga must be enabled in order to measure any input with a gain greater than 1. the input voltage must meet the input and output voltage restrictions of the pga, as explained in the pga input- voltage requirements section when the pga is enabled. setting the input voltage at or near (avss + avdd) / 2 in most cases satisfies the pga input voltage requirements. signals where both the positive and negative inputs are always 0 v are called unipolar signals . these signals can in general be measured with the ads114s0x using a unipolar analog supply (avss = 0 v). as mentioned previously, the pga must be bypassed in order to measure single-ended, unipolar signals when using a unipolar supply. a signal is called bipolar when either the positive or negative input can swing below 0 v. a bipolar analog supply (such as avdd = 2.5 v, avss = ? 2.5 v) is required in order to measure bipolar signals with the ads114s0x. a typical application task is measuring a single-ended, bipolar, 10-v signal where ain n is fixed at 0 v and ain p swings between ? 10 v and 10 v. the ads114s0x cannot directly measure this signal because the 10-v signal exceeds the analog power-supply limits. however, one possible solution is to use a bipolar analog supply (avdd = 2.5 v, avss = ? 2.5 v), gain = 1, and a resistor divider in front of the ads114s0x. the resistor divider must divide the voltage down to 2.5 v to be able to measure the voltage using the internal 2.5-v reference. 10.1.5 unused inputs and outputs to minimize leakage currents on the analog inputs, leave unused analog and reference inputs floating, or connect the inputs to mid-supply or to avdd. connecting unused analog or reference inputs to avss is possible as well, but can yield higher leakage currents than the previously mentioned options. refn0 is an exception; this pin can be accidently shorted to avss through the internal low-side switch. leave the refn0 pin floating when not in use or tie the pin to avss. gpio pins operate on levels based on the analog supply. do not float gpio pins that are configured as digital inputs. tie unused gpio pins that are configured as digital inputs to the appropriate levels, avdd or avss, including when in power-down mode. tie unused gpio output pins to avss through a pulldown resistor and set the output to 0 in the gpio data register. for unused gpio pins on the ads114s06, leave the gpiocon register set to the default register values and connect these gpio pins in the same manner as for an unused analog input. do not float unused digital inputs; excessive power-supply leakage current can result. tie all unused digital inputs to the appropriate levels, iovdd or dgnd, even when in power-down mode. connections for unused digital inputs are listed below. ? tie the cs pin to dgnd if cs is not used ? tie the clk pin to dgnd if the internal oscillator is used ? tie the start/sync pin to dgnd to control conversions by commands ? tie the reset pin to iovdd if the reset pin is not used ? if the drdy output is not used, leave the drdy pin unconnected or tie the drdy pin to iovdd using a weak pullup resistor advance information 86 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated application information (continued) 10.1.6 pseudo code example the following list shows a pseudo code sequence with the required steps to set up the device and the microcontroller that interfaces to the adc in order to take subsequent readings from the ads114s0x in continuous conversion mode. the dedicated drdy pin is used to indicate availability of new conversion data. spower-up so that all supplies reach minimum operating levels; delay for a minimum of 2.2 ms to allow power supplies to settle and power-up reset to complete; configure the spi interface of the microcontroller to spi mode 1 (cpol = 0, cpha =1); if the cs pin is not tied low permanently, configure the microcontroller gpio connected to cs as an output; configure the microcontroller gpio connected to the drdy pin as a falling edge triggered interrupt input; set cs to the device low; delay for a minimum of t d(cssc) ; send the reset command (06h) to make sure the device is properly reset after power-up; //optional delay for a minimum of 4096 t clk ; read the status register using the rreg command to check that the rdy bit is 0; //optional clear the fl_por flag by writing 00h to the status register; //optional write the respective register configuration with the wreg command; for verification, read back all configuration registers with the rreg command; send the start command (08h) to start converting in continuous conversion mode; delay for a minimum of t d(sccs) ; clear cs to high (resets the serial interface); loop { wait for drdy to transition low; take cs low; delay for a minimum of t d(cssc) ; send the rdata command; send 16 sclk rising edges to read out conversion data on dout/ drdy; delay for a minimum of t d(sccs) ; clear cs to high; } take cs low; delay for a minimum of t d(cssc) ; send the stop command (0ah) to stop conversions and put the device in standby mode; delay for a minimum of t d(sccs) ; clear cs to high; advance information 87 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 10.2 typical application figure 101 shows a fault-protected, filtered, 3-wire rtd application circuit with hardware-based, lead-wire compensation. two idac current sources provide the lead-wire compensation. one idac current source (idac1) provides excitation to the rtd element. the adc reference voltage (pins ain6 and ain7) is derived from the voltage across resistor r ref sourcing the same idac1 current, providing ratiometric cancellation of current-source drift. the other current source (idac2) has the same current setting, providing cancellation of lead-wire resistance by generating a voltage drop across lead-wire resistance r lead2 equal to the voltage drop of r lead1 . because the r rtd voltage is measured differentially at adc pins ain1 and ain2, the voltages across the lead wire resistance cancel. resistor r bias level-shifts the rtd signal to within the adc specified input range. the current sources are provided by two additional pins (ain5 and ain3) that connect to the rtd through blocking diodes. the additional pins are used to route the rtd excitation currents around the input filter resistors, avoiding the voltage drop otherwise caused by the filter resistors r f1 and r f4 . the diodes protect the adc inputs in the event of a miswired connection. the input filter resistors limit the input fault currents flowing into the adc. figure 101. 3-wire rtd application 10.2.1 design requirements table 44 shows the design requirements of the 3-wire rtd application. (1) t a = 25 c. after offset and full-scale calibration. table 44. design requirements design parameter value adc supply voltage 4.75 v (minimum) rtd sensor type 3-wire pt100 rtd resistance range 20 to 400 rtd lead resistance range 0 to 10 rtd self heating 1 mw accuracy (1) 0.1 advance information dout/drdy reset din ain1 ain2 ain3 c dif1 c cm1 c cm2 r f2 r f1 r lead2 r lead1 r rtd (idac2) (refp1) i idac1 + i idac2 4.096-mhz oscillator clk c dif2 c cm3 c cm4 r f4 r f3 ain6 ain7 ain5 5 v 330 nf ads114s08 16-bit ? adc pga r lead3 500 a idac2 3-wire rtd i idac2 i idac1 r ref r bias 500 a idac1 (refn1) (idac1) (ainp) (ainn) avdd avdd avdd dvdd avss dgnd internal reference digital filter serial interface and control cs sclk drdy start/sync reference detection pga rail detection reference mux refout input mux reference buffers refcom iovdd 3.3 v 0.1 p f avss-sw 1 p f copyright ? 2017, texas instruments incorporated 88 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) v refmin is the minimum reference voltage required by the design. (2) v ref is the design target reference voltage allowing for 10% overrange. (3) v ainnlim is the absolute minimum input voltage required by the adc. (4) v ainplim is the absolute maximum input voltage required by the adc. (5) v rtdn is the design target negative input voltage. (6) v rtdp is the design target positive input voltage. (7) v idac1 is the design target idac1 loop voltage. 10.2.2 detailed design procedure the key considerations in the design of a 3-wire rtd circuit are the accuracy, the lead wire compensation, and the sensor self-heating. as the design values of table 45 show, several values of excitation currents are available. the resolution is expressed in units of noise-free resolution (nfr). noise-free resolution is resolution with no code flicker. the selection of excitation currents trades off resolution against sensor self-heating. in general, measurement resolution improves with increasing excitation current. increasing the excitation current beyond 1000 a results in no further improvement in resolution for this example circuit. the design procedure is based on a 500- a excitation current, because this level of current results in very low sensor self-heating (0.4 mw). table 45. rtd circuit design parameters i idac ( a) nfr (bits) p rtd (mw) v rtd (v) gain (v/v) v refmin (1) (v) v ref (2) (v) r ref (k ) v ainnlim (3) (v) v ainplim (4) (v) r bias (k ) v rtdn (5) (v) v rtdp (6) (v) v idac1 (7) (v) 50 16.8 0.001 0.02 32 0.64 0.70 18 0.6 4.1 7.10 0.7 0.7 1.9 100 17.8 0.004 0.04 32 1.28 1.41 14.1 0.9 3.8 5.10 1.0 1.1 2.8 250 18.8 0.025 0.10 16 1.60 1.76 7.04 1.1 3.7 2.30 1.2 1.3 3.3 500 19.1 0.100 0.20 8 1.60 1.76 3.52 1.0 3.8 1.10 1.1 1.3 3.4 750 18.9 0.225 0.30 4 1.20 1.32 1.76 0.8 4.0 0.57 0.9 1.2 2.8 1000 19.3 0.400 0.40 4 1.60 1.76 1.76 0.9 3.9 0.50 1.0 1.4 3.5 1500 19.1 0.900 0.60 2 1.20 1.32 0.88 0.6 4.2 0.23 0.7 1.3 3.0 2000 18.3 1.600 0.80 1 0.80 0.90 0.45 0.3 4.5 0.10 0.4 1.2 2.4 initially, r lead1 and r lead2 are considered to be 0 . route the idac1 current through the external reference resistor, r ref . idac1 generates the adc reference voltage, v ref , across the reference resistor. this voltage is defined by equation 12 : v ref = i idac1 r ref (12) route the second current (idac2) to the second rtd lead. program the idac value by using the idacmag register; however, only the idac1 current flows through the reference resistor and rtd. the idac1 current excites the rtd to produce a voltage proportional to the rtd resistance. the rtd voltage is defined by equation 13 : v rtd = r rtd i idac1 (13) the adc amplifies the rtd signal voltage (v rtd ) and measures the resulting voltage against the reference voltage to produce a proportional digital output code, as shown in equation 14 through equation 16 . code v rtd gain / v ref (14) code (r rtd i idac1 ) gain / (i idac1 r ref ) (15) code (r rtd gain) / r ref (16) as shown in equation 16 , the rtd measurement depends on the value of the rtd, the pga gain, and the reference resistor r ref , but not on the idac1 value. therefore, the absolute accuracy and temperature drift of the excitation current does not matter. the second excitation current (idac2) provides a second voltage drop across the second rtd lead resistance, r lead2 . the second voltage drop compensates the voltage drop caused by i dac1 and r lead1 . the leads of a 3- wire rtd typically have the same length; therefore, the lead resistance is typically identical. taking the lead resistance into account (r leadx 0), the differential voltage (v in ) across adc inputs ain8 and ain9 is shown in equation 17 : v in = i idac1 (r rtd + r lead1 ) ? i idac2 r lead2 (17) if r lead1 = r lead2 and i idac1 = i idac2 , the expression for v in reduces to equation 18 : v in = i idac1 r rtd (18) advance information 89 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated in other words, the measurement error resulting from the voltage drop across the rtd lead resistance is compensated as long as the lead resistance values and the idac values are matched. using equation 13 , the value of rtd resistance (400 , maximum) and the excitation current (500 a) yields an rtd voltage of v rtd = 500 a 400 = 0.2 v. use the maximum gain of 8 in order to limit the corresponding loop voltage of idac1. gain = 8 requires a minimum reference voltage v refmin = 0.2 v 8 = 1.6 v. to provide margin for the adc operating range, increase the target reference voltage by 10% (v ref = 1.6 v 1.1 = 1.76 v). calculate the value of the reference resistor, as shown in equation 19 : r ref = v ref / i idac1 = 1.76 v / 500 a = 3.52 k (19) for this example application, 3.5 k is chosen for r ref . for best results, use a precision reference resistor r ref with a low temperature drift ( < 10 ppm/ c). any change in r ref is reflected in the measurement as a gain error. the next step in the design is determining the value of the r bias resistor, in order to level shift the rtd voltage to meet the adc absolute input-voltage specification. the required level-shift voltage is determined by calculating the minimum absolute voltage (v ainnlim ) as shown in equation 20 : avss + 0.15 + v rtdmax (gain ? 1) / 2 v ainnlim where ? v rtdmax = maximum differential rtd voltage = 0.2 v ? gain = 8 ? avss = 0 v (20) the result of the equation requires a minimum absolute input voltage (v rtdn ) > 0.85 v. therefore, the rtd voltage must be level shifted by a minimum of 0.85 v. to meet this requirement, a target level-shift value of 1 v is chosen to provide extra margin. calculate the value of r bias as shown in equation 21 : r bias = v ainn / (i idac1 + i idac2 ) = 1 v / ( 2 500 a) = 1 k (21) after the level-shift voltage is determined, verify that the positive rtd voltage (v rtdp ) is less than the maximum absolute input voltage (v ainplim ), as shown in equation 22 : v ainplim avdd ? 0.15 ? v rtdmax (gain ? 1) / 2 where ? v rtdmax = maximum differential rtd voltage = 0.2 v ? gain = 8 ? avdd = 4.75 v (minimum) (22) solving equation 22 results in a required v rtdp of less than 3.9 v. calculate the v rtdp input voltage by equation 23 : v ainp = v rtdn + i idac1 (r rtd + r lead1 ) = 1 v + 500 a (400 + 10 ) = 1.2 v (23) because 1.2 v is less than the 3.9-v maximum input voltage limit, the absolute positive and negative rtd voltages are within the adc specified input range. the next step in the design is to verify that the idacs have enough voltage headroom (compliance voltage) to operate. the loop voltage of the excitation current must be less than the supply voltage minus the specified idac compliance voltage. calculate the voltage drop developed across each idac current path to avss. in this circuit, idac1 has the largest voltage drop developed across its current path. the idac1 calculation is sufficient to satisfy idac2 because the idac2 voltage drop is always less than idac1 voltage drop. the sum of voltages in the idac1 loop is shown in equation 24 : v idac1 = [(i idac1 + i idac2 ) (r lead3 + r bias )] + [i idac1 (r rtd + r lead1 + r ref )] + v d where ? v d = external blocking diode voltage (24) the equation results in a loop voltage of v idac1 = 3.0 v. the worst-case current source compliance voltage is: (avdd ? 0.4 v) = (4.75 v ? 0.4 v) = 4.35 v. the v idac1 loop voltage is less than the specified current source compliance voltage (3.0 v < 4.35 v). advance information 90 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated (1) a two-point offset and gain calibration removes errors from the r ref tolerance. the results are used for the ofc and fsc registers. many applications benefit from using an analog filter at the inputs to remove noise and interference from the signal. filter components are placed on the adc inputs (r f1 , r f2 , c dif1 , c cm1 , and c cm2 ), as well as on the reference inputs (r f3 , r f4 , c dif2 , c cm3 , and c cm4 ). the filters remove both differential and common-mode noise. the application shows a differential input noise filter formed by r f1 , r f2 and c dif1 , with additional differential mode capacitance provided by the common-mode filter capacitors, c cm1 and c cm2 . calculate the differential ? 3-db cutoff frequency as shown in equation 25 : f dif = 1 / [2 (r f1 + r f2 ) (c dif1 + c cm1 || c cm2 )] (25) the common-mode noise filter is formed by components r f1 , r f2 , c cm1 , and c cm2 . calculate the common-mode signal ? 3-db cutoff frequency, as shown in equation 26 : f cm = 1 / (2 r f1 c cm1 ) = 1 / (2 r f2 c cm2 ) (26) mismatches in the common-mode filter components convert common-mode noise into differential noise. to reduce the effect of mismatch, use a differential mode filter with a corner frequency that is at least 10 times lower than the common-mode filter corner frequency. the low-frequency differential filter removes the common-mode converted noise. the filter resistors (r fx ) also serve as current-limiting resistors. these resistors limit the current into the analog inputs (ainx) of the device to safe levels when an overvoltage occurs on the inputs. filter resistors lead to an offset voltage error due to the dc input current leakage flowing into and out of the device. remove this voltage error by system offset calibration. resistor values that are too large generate excess thermal noise and degrade the overall noise performance. the recommended range of the filter resistor values is 100 to 10 k . the properties of the capacitors are important because the capacitors are connected to the signal; use high-quality c0g ceramics or film-type capacitors. for consistent noise performance across the full range of rtd measurements, match the corner frequencies of the input and reference filter. see the rtd ratiometric measurements and filtering using the ads1148 and ads1248 application report (sbaa201) for detailed information on matching the input and reference filter. 10.2.2.1 register settings the register settings for this design are shown in table 46 . table 46. register settings register name setting description 02h inpmux 12h select ain p = ain1 and ain n = ain2 03h pga 0bh pga enabled, pga gain = 8 04h datarate 14h continuous conversion mode, low-latency filter, 20-sps data rate 05h ref 06h positive and negative reference buffers enabled, refp1 and refn1 reference inputs selected, internal reference always on 06h idacmag 05h idac magnitude set to 500 a 07h idacmux 35h idac2 set to ain3, idac1 set to ain5 08h vbias 00h 09h sys 10h 0ah ofcal0 (1) xxh 0bh ofcal1 xxh 0ch ofcal2 xxh 0dh fscal0 (1) xxh 0eh fscal1 xxh 0fh fscal2 xxh 10h gpiodat 00h 11h gpiocon 00h advance information 91 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 10.2.3 application curves to test the accuracy of the acquisition circuit, a series of calibrated high-precision discrete resistors are used as an input to the system. measurements are taken at t a = 25 c. figure 102 displays the resistance measurement over an input span from 20 to 400 . any offset error is generally attributed to the offset of the adc, and the gain error can be attributed to the accuracy of the r ref resistor and the adc. the r ref value is also calibrated to reduce the gain error contribution. precision temperature measurement applications are typically calibrated to remove the effects of gain and offset errors that generally dominate the total system error. the simplest calibration method is a linear, or two-point calibration that applies an equal and opposite gain and offset term to cancel the measured system gain and offset error. in this particular tested application, the gain and offset error was very small, and did not require additional calibration other than the self offset and gain calibration provided by the device. the resulting measured resistance error is shown in figure 103 . the results in figure 103 are converted to temperature accuracy by dividing the results by the rtd sensitivity ( ) at the measured resistance. over the full resistance input range, the maximum total measured error is 0.0190 . equation 27 uses the measured resistance error and the rtd sensitivity at 0 c to calculate the measured temperature accuracy. error ( c) = error ( ) / @0 c = 0.0190 / 0.39083 / c = 0.049 c (27) figure 104 displays the calculated temperature accuracy of the circuit assuming a linear rtd resistance to temperature response. this figure does not include any linearity compensation of the rtd , but figure 104 does remove offset and gain error, which can be calibrated with the ofc and fsc registers. figure 102. adc output code vs equivalent rtd resistance figure 103. measured resistance error vs equivalent rtd resistance figure 104. equivalent temperature error vs equivalent rtd resistance resistance ( : ) resistance error ( : ) 0 50 100 150 200 250 300 350 400 450 -0.03 -0.02 -0.01 0 0.01 0.02 0.03 advance information resistance ( : ) temperature error ( q c) 0 50 100 150 200 250 300 350 400 450 -0.06 -0.04 -0.02 0 0.02 0.04 0.06 resistance ( : ) adc output (code) 0 50 100 150 200 250 300 350 400 450 0 5000 10000 15000 20000 25000 30000 35000 92 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 10.3 do ' s and don ' ts ? do partition the analog, digital, and power-supply circuitry into separate sections on the pcb. ? do use a single ground plane for analog and digital grounds. ? do place the analog components close to the adc pins using short, direct connections. ? do keep the sclk pin free of glitches and noise. ? do verify that the analog input voltages are within the specified pga input voltage range under all input conditions. ? do float unused analog input pins to minimize input leakage current on all other analog inputs. connecting unused pins to avdd is the next best option. ? do provide current limiting to the analog inputs in case overvoltage faults occur. ? do use a low-dropout linear regulator (ldo) to reduce ripple voltage generated by switch-mode power supplies. reducing ripple is especially important for avdd where the supply noise can affect the performance. ? don't cross analog and digital signals. ? don't allow the analog and digital power supply voltages to exceed 5.5 v under any condition, including during power-up and power-down. advance information 93 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated do ' s and don ' ts (continued) figure 105 shows the do's and don'ts of the adc circuit connections. figure 105. do ' s and don ' ts circuit connections ain p ain n 16-bit ? adc pga avss device 5 v avdd 0 v 0 v correct incorrect ain p ain n 16-bit ? adc pga avss device 5 v avdd 0 v 0 v ain p ain n 16-bit ? adc pga avss device 5 v avdd 0 v 2.5 v correct ain p ain n 16-bit ? adc pga avss device 2.5 v avdd -2.5 v 0 v pga enabled correct single-ended input, pga enabled single-ended input, pga bypassed single-ended input, pga enabled single-ended input, pga enabled incorrect inductive supply or ground connections correct low impedance agnd/dgnd connection correct low impedance agnd/dgnd connection incorrect agnd/dgnd isolation 16-bit ? adc pga device dvdd 5 v avdd 3.3 v avss dgnd 16-bit ? adc pga device dvdd 5 v avdd 3.3 v avss dgnd 16-bit ? adc pga device dvdd 5 v avdd 3.3 v avss dgnd 16-bit ? adc pga device dvdd 2.5 v avdd 3.3 v avss dgnd -2.5 v advance information 94 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 11 power supply recommendations 11.1 power supplies the ads114s0x requires three power supplies: analog (avdd, avss), digital core (dvdd, dgnd), and digital i/o (iovdd, dgnd). the analog power supply can be bipolar (for example, avdd = 2.5 v, avss = ? 2.5 v) or unipolar (for example, avdd = 3.3 v, avss = 0 v) and is independent of the digital power supplies. dvdd is used to power the digital circuits of the devices. iovdd sets the digital i/o levels (with the exception of the gpio levels that are set by the analog supply of avdd and avss). iovdd must be equal to or larger than dvdd. 11.2 power-supply sequencing avdd and dvdd may be powered up in any order. however, iovdd is recommended to be powered up before or at the same time as dvdd. if dvdd comes up before iovdd, a reset of the device using the reset pin or the reset command may be required. 11.3 power-on reset an internal por is released after all three supplies exceed approximately 1.65 v. each supply has an individual por circuit. a brownout condition on any of the three supplies triggers a reset of the complete device. 11.4 power-supply decoupling good power-supply decoupling is important to achieve best performance. avdd must be decoupled with at least a 330-nf capacitor to avss. dvdd and iovdd (when not connected to dvdd) must be decoupled with at least a 0.1- f capacitor to dgnd. figure 106 and figure 107 show typical power-supply decoupling examples for unipolar and bipolar analog supplies, respectively. place the bypass capacitors as close to the power-supply pins of the device as possible using low-impedance connections. use multi-layer ceramic chip capacitors (mlccs) that offer low equivalent series resistance (esr) and inductance (esl) characteristics for power-supply decoupling purposes. to reduce inductance on the supply pins, avoid the use of vias for connecting the capacitors to the supply pins. the use of multiple vias in parallel lowers the overall inductance and is beneficial for connections to ground planes. connect analog and digital grounds together as close to the device as possible. figure 106. unipolar analog power supply figure 107. bipolar analog power supply 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 aincom ain5 ain4 ain3 ain2 ain1 ain0 start/sync dgnd iovdd dvdd clk reset gpio3/ain11 gpio2/ain10 gpio1/ain9 gpio0/ain8 refout refcom nc avdd avss avss-sw refn0 refp0 refn1/ain7 refp1/ain6 330 nf 5 v 0.1 p f 3.3 v 1 p f cs din sclk dout/drdy drdy 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 aincom ain5 ain4 ain3 ain2 ain1 ain0 start/sync cs din sclk dout/drdy drdy dgnd iovdd dvdd nc avdd avss avss-sw refn0 refp0 refn1/ain7 refp1/ain6 +2.5 v 1 p f 330 nf 2.5 v clk reset gpio3/ain11 gpio2/ain10 gpio1/ain9 gpio0/ain8 refout refcom 0.1 p f 3.3 v 2.5 v advance information 95 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 12 layout 12.1 layout guidelines employing best design practices is recommended when laying out a printed-circuit board (pcb) for both analog and digital components. this recommendation generally means that the layout separates analog components [such as adcs, amplifiers, references, digital-to-analog converters (dacs), and analog muxs] from digital components [such as microcontrollers, complex programmable logic devices (cplds), field-programmable gate arrays (fpgas), radio frequency (rf) transceivers, universal serial bus (usb) transceivers, and switching regulators]. an example of good component placement is shown in figure 108 . although figure 108 provides a good example of component placement, the best placement for each application is unique to the geometries, components, and pcb fabrication capabilities employed. that is, there is no single layout that is perfect for every design and careful consideration must always be used when designing with any analog component. figure 108. system component placement the following basic recommendations for layout of the ads114s0x help achieve the best possible performance of the adc. a good design can be ruined with a bad circuit layout. ? separate analog and digital signals. to start, partition the board into analog and digital sections where the layout permits. route digital lines away from analog lines. this prevents digital noise from coupling back into analog signals. ? the ground plane can be split into an analog plane (agnd) and digital plane (dgnd), but this (splitting) is not necessary. place digital signals over the digital plane, and analog signals over the analog plane. as a final step in the layout, the split between the analog and digital grounds must be connected to together at the adc. ? fill void areas on signal layers with ground fill. ? provide good ground return paths. signal return currents will flow on the path of least impedance. if the ground plane is cut or has other traces that block the current from flowing right next to the signal trace, another path must be found to return to the source and complete the circuit. if forced into a larger path, the chance that the signal radiates increases. sensitive signals are more susceptible to emi interference. ? use bypass capacitors on supplies to reduce high-frequency noise. do not place vias between bypass capacitors and the active device. placing the bypass capacitors on the same layer as close to the active device yields the best results. ? consider the resistance and inductance of the routing. often, traces for the inputs have resistances that react with the input bias current and cause an added error voltage. reducing the loop area enclosed by the source signal and the return current reduces the inductance in the path. reducing the inductance reduces the emi pickup and reduces the high-frequency impedance at the input of the device. ? watch for parasitic thermocouples in the layout. dissimilar metals going from each analog input to the sensor can create a parasitic themocouple that can add an offset to the measurement. differential inputs must be matched for both the inputs going to the measurement source. ? analog inputs with differential connections must have a capacitor placed differentially across the inputs. best input combinations for differential measurements use adjacent analog input lines (such as ain0, ain1 and ain2, ain3). the differential capacitors must be of high quality. the best ceramic chip capacitors are c0g (npo) that have stable properties and low noise characteristics. advance information device microcontroller signal conditioning (rc filters and amplifiers) supply generation connector or antenna ground fill or ground plane optional: split ground cut ground fill or ground plane optional: split ground cut interface transceiver ground fill or ground plane ground fill or ground plane 96 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 12.2 layout example figure 109. ads114s0x layout example ain11 ain10 ain9 ain8 1: aincom 2: ain5 3: ain4 4: ain3 5: ain2 6: ain1 7: ain0 8: start 9: cs 10: din 11: sclk 12: dout/ drdy 13: drdy 14: dgnd 15: iovdd 16: dvdd 25: nc 26: avdd 27: avss 28: avss/sw 29: refn0 30: refp0 31: refn1/ ain7 32: refp1/ ain6 17: clk 18: reset 19: gpio3/ ain11 20: gpio2/ ain10 21: gpio1/ ain9 22: gpio0/ ain8 23: refout 24: refcom ain0 ain1 ain2 ain3 cs start din sclk dout/drdy drdy ain4 ain5 clk reset refn0 refp0 ain6 ain7 avss/sw internal plane connected to gnd (dgnd = avss) differential input differential input or reference input reference input via connection to power plane differential input differential input differential input differential input digital connections advance information 97 ads114s06 , ads114s08 www.ti.com sbas815 ? february 2017 product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 13 device and documentation support 13.1 device support 13.1.1 development support ads1x4s0x design calculator 13.2 documentation support 13.2.1 related documentation for related documentation see the following: ? ref50xx low-noise, very low drift, precision voltage reference ? rtd ratiometric measurements and filtering using the ads1148 and ads1248 application report ? 3-wire rtd measurement system reference design, -200 c to 850 c 13.3 related links the table below lists quick access links. categories include technical documents, support and community resources, tools and software, and quick access to order now. table 47. related links parts product folder order now technical documents tools & software support & community ads114s06 click here click here click here click here click here ads114s08 click here click here click here click here click here 13.4 receiving notification of documentation updates to receive notification of documentation updates, navigate to the device product folder on ti.com. in the upper right corner, click on alert me to register and receive a weekly digest of any product information that has changed. for change details, review the revision history included in any revised document. 13.5 community resources the following links connect to ti community resources. linked contents are provided "as is" by the respective contributors. they do not constitute ti specifications and do not necessarily reflect ti's views; see ti's terms of use . ti e2e ? online community ti's engineer-to-engineer (e2e) community. created to foster collaboration among engineers. at e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. design support ti's design support quickly find helpful e2e forums along with design support tools and contact information for technical support. 13.6 trademarks e2e is a trademark of texas instruments. all other trademarks are the property of their respective owners. 13.7 electrostatic discharge caution this integrated circuit can be damaged by esd. texas instruments recommends that all integrated circuits be handled with appropriate precautions. failure to observe proper handling and installation procedures can cause damage. esd damage can range from subtle performance degradation to complete device failure. precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. advance information 98 ads114s06 , ads114s08 sbas815 ? february 2017 www.ti.com product folder links: ads114s06 ads114s08 submit documentation feedback copyright ? 2017, texas instruments incorporated 13.8 glossary slyz022 ? ti glossary . this glossary lists and explains terms, acronyms, and definitions. 14 mechanical, packaging, and orderable information the following pages include mechanical packaging and orderable information. this information is the most current data available for the designated devices. this data is subject to change without notice and revision of this document. for browser-based versions of this data sheet, refer to the left-hand navigation. advance information package option addendum www.ti.com 9-mar-2017 addendum-page 1 packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish (6) msl peak temp (3) op temp (c) device marking (4/5) samples ads114s06ipbs preview tqfp pbs 32 250 tbd call ti call ti -50 to 125 ads114s06ipbsr preview tqfp pbs 32 1000 tbd call ti call ti -50 to 125 ads114s06irhbr preview vqfn rhb 32 3000 tbd call ti call ti -50 to 125 ads114s06irhbt preview vqfn rhb 32 250 tbd call ti call ti -50 to 125 ads114s08ipbs preview tqfp pbs 32 250 tbd call ti call ti -50 to 125 114s08 ads114s08ipbsr preview tqfp pbs 32 1000 tbd call ti call ti -50 to 125 114s08 ads114s08irhbr preview vqfn rhb 32 3000 tbd call ti call ti -50 to 125 ads114s08irhbt preview vqfn rhb 32 250 tbd call ti call ti -50 to 125 PADS114S08IPBSR active tqfp pbs 32 1000 tbd call ti call ti -50 to 125 (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs), pb-free (rohs exempt), or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. pb-free (rohs exempt): this component has a rohs exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. the component is otherwise considered pb-free (rohs compatible) as defined above. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. - the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. (4) there may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) multiple device markings will be inside parentheses. only one device marking contained in parentheses and separated by a "~" will appear on a device. if a line is indented then it is a continuation of the previous line and the two combined represent the entire device marking for that device. package option addendum www.ti.com 9-mar-2017 addendum-page 2 (6) lead/ball finish - orderable devices may have multiple material finish options. finish options are separated by a vertical ruled line. lead/ball finish values may wrap to two lines if the finish value exceeds the maximum column width. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis. important notice for ti design information and resources texas instruments incorporated ( ? ti ? ) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, ? ti resources ? ) are intended to assist designers who are developing applications that incorporate ti products; by downloading, accessing or using any particular ti resource in any way, you (individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of this notice. ti ? s provision of ti resources does not expand or otherwise alter ti ? s applicable published warranties or warranty disclaimers for ti products, and no additional obligations or liabilities arise from ti providing such ti resources. ti reserves the right to make corrections, enhancements, improvements and other changes to its ti resources. you understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications (and of all ti products used in or for your applications) with all applicable regulations, laws and other applicable requirements. you represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. you agree that prior to using or distributing any applications that include ti products, you will thoroughly test such applications and the functionality of such ti products as used in such applications. ti has not conducted any testing other than that specifically described in the published documentation for a particular ti resource. you are authorized to use, copy and modify any individual ti resource only in connection with the development of applications that include the ti product(s) identified in such ti resource. no other license, express or implied, by estoppel or otherwise to any other ti intellectual property right, and no license to any technology or intellectual property right of ti or any third party is granted herein, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which ti products or services are used. information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. use of ti resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. ti resources are provided ? as is ? and with all faults. ti disclaims all other warranties or representations, express or implied, regarding ti resources or use thereof, including but not limited to accuracy or completeness, title, any epidemic failure warranty and any implied warranties of merchantability, fitness for a particular purpose, and non-infringement of any third party intellectual property rights. ti shall not be liable for and shall not defend or indemnify you against any claim, including but not limited to any infringement claim that relates to or is based on any combination of products even if described in ti resources or otherwise. in no event shall ti be liable for any actual, direct, special, collateral, indirect, punitive, incidental, consequential or exemplary damages in connection with or arising out of ti resources or use thereof, and regardless of whether ti has been advised of the possibility of such damages. you agree to fully indemnify ti and its representatives against any damages, costs, losses, and/or liabilities arising out of your non- compliance with the terms and provisions of this notice. this notice applies to ti resources. additional terms apply to the use and purchase of certain types of materials, ti products and services. these include; without limitation, ti ? s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm ), evaluation modules , and samples ( http://www.ti.com/sc/docs/sampterms.htm ). mailing address: texas instruments, post office box 655303, dallas, texas 75265 copyright ? 2017, texas instruments incorporated |
Price & Availability of PADS114S08IPBSR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |