spec no: dsaj8918 rev no: v.7b date: dec/23/2015 page: 1 of 5 approved: wynec checked: joe lee drawn: l.q.xie erp: 1352000563 surface mount display attention observe precautions for handling electrostatic discharge sensitive devices part number: acda56-41qbwa/d-f01 blue features z 0.56 inch digit height. z low current operation. z excellent character appearance. z mechanically rugged. z gray face, white segment. z package: 200pcs/ reel. z moisture sensitivity level : level 2a. z rohs compliant. descriptions z the blue source color devices are made with ingan light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions& internal circuit diagram notes: 1. all dimensions are in millimeters (inches), tolerance is 0.25(0.01")unless otherwise noted. 2. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 3.the gap between the reflector and pcb shall not exceed 0.25mm.
spec no: dsaj8918 rev no: v.7b date: dec/23/2015 page: 2 of 5 approved: wynec checked: joe lee drawn: l.q.xie erp: 1352000563 selection guide notes: 1. luminous intensity / luminous flux: +/-15%. 2. luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (ucd) [1] @ 10ma min. typ. acda56-41qbwa/d- f01 blue (ingan) white diffused 5600 15000 common anode, rt. hand decimal. description symbol parameter emitting color typ. max. units test conditions peak peak wavelength blue 460 nm i f =10ma d [1] dominant wavelength blue 465 nm i f =10ma ? 1/2 spectral line half-width blue 25 nm i f =10ma c capacitance blue 100 pf v f =0v;f=1mhz v f [2] forward voltage blue 3.0 4.0 v i f =10ma i r reverse current blue 50 ua v r =5v parameter values units power dissipation 120 mw dc forward current 30 ma peak forward current [1] 150 ma reverse voltage 5 v operating / storage temperature -40c to +85c electrostatic discharge th reshold (hbm) 250 v
spec no: dsaj8918 rev no: v.7b date: dec/23/2015 page: 3 of 5 approved: wynec checked: joe lee drawn: l.q.xie erp: 1352000563 blue acda56-41qbwa/d-f01
spec no: dsaj8918 rev no: v.7b date: dec/23/2015 page: 4 of 5 approved: wynec checked: joe lee drawn: l.q.xie erp: 1352000563 acda56-41qbwa/d-f01 recommended soldering pattern (units : mm; tolerance: 0.15) reel dimension tape specifications (units : mm)
spec no: dsaj8918 rev no: v.7b date: dec/23/2015 page: 5 of 5 approved: wynec checked: joe lee drawn: l.q.xie erp: 1352000563 packing & label specifications acda56-41qbwa/d-f01 terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
