Part Number Hot Search : 
C100LV DA726 357LA3C HT6750A F0035 HM62V1 SF2N5575 SD103
Product Description
Full Text Search
 

To Download A5970D Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  this is information on a product in full production. march 2014 docid13955 rev 7 1/41 A5970D up to 1 a step-down switching regu lator for automotive applications datasheet - production data features ? qualified following the aec-q100 requirements (see ppap for more details) ? 1 a dc output current ? operating input voltage from 4 v to 36 v ? 3.3 v / ( 2%) reference voltage ? output voltage adjustable from 1.235 v to v in ? low dropout op eration: 100% duty cycle ? 250 khz internally fixed frequency ? voltage feed-forward ? zero load current operation ? internal current limiting ? inhibit for zero current consumption ? synchronization ? protection against feedback disconnection ? thermal shutdown application ? dedicated to automotive applications description the A5970D is a step-down monolithic power switching regulator with a minimum switch current limit of 1.35 a so it is ab le to deliver up to 1 a dc current to the load depending on the application conditions. the output voltage can be set from 1.235 v to v in . the device uses an internal p-channel dmos transistor (with a typical r ds(on) of 250 m ? ) as switching element to minimize the size of the external components. an internal oscillator fixe s the switching frequency at 250 khz. having a minimum input voltage of 4 v only it fits the automotive applications requiring the device operation even in cold crank conditions. pulse by pulse current limit with the internal frequency modulation offers an effective constant current shor t-circuit protection. so8 figure 1. application schematic www.st.com
contents A5970D 2/41 docid13955 rev 7 contents 1 pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 datasheet parameters over the temperatur e range . . . . . . . . . . . . . . . . 8 5 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.1 power supply and voltage reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.2 voltages monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.3 oscillator and synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.4 current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5.5 error amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.6 pwm comparator and power stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.7 inhibit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.8 thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 additional features and protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.1 feedback disconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.2 output overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.3 zero load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7 closing the loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.1 error amplifier and compensation network . . . . . . . . . . . . . . . . . . . . . . . . 17 7.2 lc filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.3 pwm comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
docid13955 rev 7 3/41 A5970D contents 41 8 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8.1 component selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8.2 layout considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.3 thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.4 short-circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8.5 application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8.6 positive buck-boost regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8.7 negative buck-boost regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 8.8 synchronization example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8.9 compensation network with mlcc at the output . . . . . . . . . . . . . . . . . . . 34 8.10 external soft_start network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9 typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 10 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 11 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
pin settings A5970D 4/41 docid13955 rev 7 1 pin settings 1.1 pin connection figure 2. pin connection (top view) 1.2 pin description table 1. pin description no. pin description 1 out regulator output. 2 synch master/slave synchronization. 3inh a logical signal (active high) disables the device. if inh not used, the pin must be grounded. when it is open, an internal pull-up disables the device. 4 comp e/a output for frequency compensation. 5fb feedback input. connecting directly to this pin results in an output voltage of 1.23 v. an external re sistive divider is required for higher output voltages. 6 vref 3.3 v v ref . no cap is requested for stability. 7 gnd ground. 8 vcc unregulated dc input voltage.
docid13955 rev 7 5/41 A5970D electrical data 41 2 electrical data 2.1 maximum ratings 2.2 thermal data table 2. absolute maximum ratings symbol parameter value unit v 8 input voltage 40 v v 1 out pin dc voltage out pin peak voltage at ? t = 0.1 ? s -1 to 40 -5 to 40 v v i 1 maximum output current int. limit. v 4 , v 5 analog pins 4 v v 3 inh -0.3 to v cc v v 2 synch -0.3 to 4 v p tot power dissipation at t a ?? 70 c 0.6 w t j operating junction temperature range -40 to 150 c t stg storage temperature range -55 to 150 c table 3. thermal data symbol parameter value unit r thja maximum thermal resistance junction ambient 120 (1) 1. package mounted on evaluation board. c/w
electrical characteristics A5970D 6/41 docid13955 rev 7 3 electrical characteristics t j = -40 c to 125 c, v cc = 12 v, unless otherwise specified. table 4. electrical characteristics symbol parameter test condition min. typ. max. unit v cc operating input voltage range 4 36 v r ds(on) mosfet on resistance 0.250 0.5 ? i l maximum limiting current (1) v cc = 5 v 1.35 1.87 2.25 a v cc = 5 v, t j = 25 c 1.5 1.87 2.25 f sw switching frequency 212 250 280 khz duty cycle 0 100 % dynamic characteristics (see test circuit). v 5 voltage feedback 4.4 v < v cc < 36 v 1.198 1.235 1.272 v ? efficiency v 0 = 5 v, v cc = 12 v 90 % dc characteristics i qop total operating quiescent current 35ma i q quiescent current duty cycle = 0; v fb = 1.5 v 2.5 ma i qst-by total standby quiescent current v inh > 2.2 v 50 100 ? a v cc = 36 v; v inh > 2.2 v 80 150 ? a inhibit inh threshold voltage device on 0.8 v device off 2.2 v error amplifier v oh high level output voltage v fb = 1 v 3.5 v v ol low level output voltage v fb = 1.5 v 0.4 v i o source source output current v comp = 1.9 v; v fb = 1 v 190 300 ? a i o sink sink output current v comp = 1.9 v; v fb =1.5 v 11.5 ma i b source bias current 2.5 4 ? a dc open loop gain r l = ? 50 65 db gm transconductance i comp = -0.1 ma to 0.1 ma; v comp = 1.9 v 2.3 ms synch function high input voltage v cc = 4.4 to 36 v 2.5 v ref v low input voltage v cc = 4.4 to 36 v 0.74 v slave synch current v synch = 0.74 v (2) v synch = 2.33 v 0.11 0.21 0.25 0.45 ma
docid13955 rev 7 7/41 A5970D electrical characteristics 41 master output amplitude i source = 3 ma 2.75 3 v output pulse width no load, v synch = 1.65 v 0.20 0.35 ? s reference section reference voltage i ref = 0 to 5 ma v cc = 4.4 v to 36 v 3.2 3.3 3.399 v line regulation i ref = 0 ma v cc = 4.4 v to 36 v 510mv load regulation i ref = 0 ma 8 15 mv short-circuit current 5 18 35 ma 1. with t j = 85 c, i lim_min = 1.5 a, assured by design, characte rization and statistical correlation. 2. guaranteed by design. table 4. electrical characteristics (continued) symbol parameter test condition min. typ. max. unit
datasheet parameters over the temperature range A5970D 8/41 docid13955 rev 7 4 datasheet parameters ov er the temperature range the 100% of the population in the production flow is tested at three different ambient temperatures (-40 c, +25 c, +125 c) to gu arantee the datasheet parameters inside the junction temperature range (-40 c, +125 c). the device operation is so guaranteed when the junction temperature is inside the (-40 c, +150 c) temperature range. the desi gner can estimate the s ilicon temperature increase respect to the ambient temperature evaluating the internal power losses generated during the device operation (please refer to section 2.2 ). however the embedded thermal protection disabl es the switching activity to protect the device in case the junction temperature reaches the t shtdwn (+150 c 10 c) temperature. all the datasheet parameters can be guarant eed to a maximum junction temperature of +125 c to avoid triggering the thermal shutdown protection during the testing phase because of self-heating.
docid13955 rev 7 9/41 A5970D functional description 41 5 functional description the main internal blocks are shown in the device block diagram in figure 3 . they are: ? a voltage regulator supplying the internal circuitry. from this regulator, a 3.3 v reference voltage is externally available. ? a voltage monitor circuit which checks the input and the internal voltages. ? a fully integrated sawt ooth oscillator with a frequency of 250 khz ?? 15%, including also the voltage feed forward function and an input/output synchronization pin. ? two embedded current limitation circuits whic h control the current that flows through the power switch. the pulse-by-pulse curren t limit forces the po wer switch off cycle by cycle if the current reaches an internal threshold, while the frequency shifter reduces the switching frequency in order to significantly reduce the duty cycle. ? a transconductance error amplifier. ? a pulse width modulator (pwm) comparator and the relative logic ci rcuitry necessary to drive the internal power. ? a high side driver for the internal p-mos switch. ? an inhibit block for standby operation. ? a circuit to implement the thermal protection function. figure 3. block diagram 5.1 power supply an d voltage reference the internal regulator circuit (shown in figure 4 ) consists of a start-up circuit, an internal voltage pre-regulator, the bandgap voltage re ference and the bias block that provides current to all the blocks. the starter supplies the start-up currents to the entire device when the input voltage goes high and the device is enabled (inhibit pin conn ected to ground). the pre-regulator block supplies the bandgap cell with a pre-regulated voltage v reg that has a very low supply volt age noise sensitivity.
functional description A5970D 10/41 docid13955 rev 7 5.2 voltages monitor an internal block continuously senses the v cc , v ref and v bg . if the voltages go higher than their thresholds, the regulator begins operat ing. there is also a hysteresis on the v cc (uvlo). figure 4. internal circuit 5.3 oscillator and synchronization figure 5 shows the block diagram of the oscillator circuit. the clock generator provides the switching freque ncy of the device, which is internally fixed at 250 khz. the frequency shifter block acts to reduce the switching frequency in case of strong overcurrent or short-circuit . the clock signal is then used in the internal logic circuitry and is the input of the ramp generator and synchronizer blocks. the ramp generator circuit provides the sawt ooth signal, used for pwm control and the internal voltage feed-forward, while the synch ronizer circuit generates the synchronization signal. the device also has a synchronization pi n which can work both as master and slave. beating frequency noise is an issue when more than one voltage rail is on the same board. a simple way to avoid this issue is to operate all the regulators at the same switching frequency. the synchronization feature of a set of the a597 0d is simply get connecting together their synch pin. the device with highest switch ing frequency will be t he master and it provides the synchronization signal to the others. therefore the synch is a i/o pin to deliver or recognize a frequency signal. the synchronization circuitr y is powered by the internal reference (v ref ) so a small filtering capacitor ( ?? 100 nf) connected between the v ref pin and the signal ground of the master device is suggested for its proper operation. however when a set of synchronized devices populates a board it is not possible to know in advance the one working as master, so the filt ering capacitor have to be designed for whole set of devices. when one or more devices are synchronized to an external signal, its amplitude have to be in comply with specific ations given in the table 4 on page 6 . the frequency of the synchronization signal must be, at a minimum, higher than the maximum guaranteed natural switching frequency of the device (275 khz, see table 4 ) while the duty cycle of the synchronization signal can vary from approximately 10% to 90%. the small capacitor under the v ref pin is required for this operation.
docid13955 rev 7 11/41 A5970D functional description 41 figure 5. oscillator circuit block diagram figure 6. synchronization example 5.4 current protection the A5970D device features tw o types of current limit pr otection: pulse-by-pulse and frequency foldback. the schematic of the current limitation circuitry for the pulse-by-pulse protection is shown in figure 7 . the output power pdmos transistor is sp lit into two parallel pdmos transistors. the smallest one includes a resistor in series, r sense . the current is sensed through r sense and if it reaches the threshold, the mi rror becomes unbalanced and the pdmos is switched off until the ne xt falling edge of the inte rnal clock pulse. due to this reduction of the out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch out gnd comp fb ss/inh a5973d synch A5970D A5970D A5970D A5970D
functional description A5970D 12/41 docid13955 rev 7 on time, the output voltage decreases. sinc e the minimum switch on time necessary to sense the current in order to avoid a false overcurrent signal is too short to obtain a sufficiently low duty cycle at 250 khz (see section 8.4 on page 26 ), the output current in strong overcurrent or short-circuit conditions could be not properly limited. for this reason the switching frequency is also reduced, thus keeping the inductor current under its maximum threshold. t he frequency shifter ( figure 5 ) functions based on the feedback voltage. as the feedback voltage decreases (due to the reduced duty cycle), the switching frequency decr eases also. figure 7. current limitation circuitry 5.5 error amplifier the voltage error amplifier is the core of the loop regulation. it is a transconductance operational amplifier whose no n inverting input is connected to the internal voltage reference (1.235 v), while the inverting input (fb) is connected to the external divider or directly to the output voltage. the out put (comp) is connected to the external compensation network. the uncompensated error amplifier has the following characteristics: the error amplifier out put is compared to the oscillato r sawtooth to perform pwm control. table 5. uncompensated error amplifier characteristics description values transconductance 2300 s low frequency gain 65 db minimum sink/source voltage 1500 a/300 a output voltage swing 0.4 v/3.65 v input bias current 2.5 a
docid13955 rev 7 13/41 A5970D functional description 41 5.6 pwm comparator and power stage this block compares the oscillator sawtooth and the error amplifie r output signals to generate the pwm signal for the driving stage. the power stage is a highly critical block, as it functions to guarantee a correct turn on and turn off of the pdmos. the turn on of the power element, or more accurately, the rise time of the current at turn on, is a very critical parameter. at a first approach, it appears that the faster the rise time, the lower the turn on losses. however, there is a limit introduced by the recovery time of the recirculation diode. in fact, when the current of the power element is equal to the inductor current, the diode turns off and the drain of the power is able to go high. but during its recovery time, the diode can be considered a high value capacitor and this produces a very high peak current, responsible for numerous problems: ? spikes on the device supply voltage that ca use oscillations (and thus noise) due to the board parasites. ? turn on overcurrent leads to a decrease in the efficiency and system reliability. ? major emi problems. ? shorter freewheeling diode life. the fall time of the current during turn off is also critical, as it produces voltage spikes (due to the parasites elements of the board) that increase the voltage drop across the pdmos. in order to minimize these problems, a new driving circuit topology has been used and the block diagram is shown in figure 8 . the basic idea is to change the current levels used to turn the power switch on and off, based on the pdmos and the gate clamp status. this circuitry allows the power switch to be turned off and on quickly and addresses the freewheeling diode recovery time problem. the gate clamp is necessary to ensure that v gs of the internal switch does not go higher than v gs max. the on/off control block protects against any cross conduction be tween the supply line and ground. figure 8. driving circuitry
functional description A5970D 14/41 docid13955 rev 7 5.7 inhibit function the inhibit feature is used to put the device in standby mode. with the inh pin higher than 2.2 v the device is disabled and the power co nsumption is reduced to less than 100 a. with the inh pin lower than 0.8 v, the device is enabled. if the inh pin is left floating, an internal pull up ensures that the voltage at the pin reaches the inhibit threshold and the device is disabled. the pin is also v cc compatible. 5.8 thermal shutdown the shutdown block generates a signal that turn s off the power stage if the temperature of the chip goes higher than a fixed internal thre shold (150 10 c). the sensing element of the chip is very close to the pdmos area, ensuring fast and accurate temperature detection. a hysteresis of approximately 20 c keeps the device from turning on and off continuously.
docid13955 rev 7 15/41 A5970D additional features and protection 41 6 additional features and protection 6.1 feedback disconnection if the feedback is disconnected, the duty cycl e increases towards the maximum allowed value, bringing the output voltage close to the input supply. this condition could destroy the load. to avoid this hazardous condition, the device is turned off if the feedback pin is left floating. 6.2 output overvoltage protection overvoltage protection, or ovp, is achieved by using an internal comparator connected to the feedback, which turns off the power stage when the ovp threshold is reached. this threshold is typically 30% higher than the feedback voltage. when a voltage divider is required to adjust the output voltage ( figure 15 on page 27 ), the ovp intervention will be set at: equation 1 where r 1 is the resistor connected between the output voltage and the feedback pin, and r 2 is between the feedback pin and ground. 6.3 zero load due to the fact that the internal power is a pdmos, no boostrap capacitor is required and so the device works properly even with no load at the output. in this case it works in burst mode, with a random burst repetition rate. v ovp 1.3 r 1 r 2 + r 2 -------------------- ? v fb ? =
closing the loop A5970D 16/41 docid13955 rev 7 7 closing the loop figure 9. block diagram of the loop
docid13955 rev 7 17/41 A5970D closing the loop 41 7.1 error amplifier an d compensation network the output l-c filter of a st ep-down converter contributes with 180 degrees phase shift in the control loop. for this reason a compensation network between the comp pin and ground is added. the simplest compensation net work together with the equivalent circuit of the error amplifier are shown in figure 10 . r c and c c introduce a pole and a zero in the open loop gain. cp does not sign ificantly affect system stability but it is useful to reduce the noise of the comp pin. the transfer function of the error amplifier and its compensation network is: equation 2 where a vo = g m r o figure 10. error amplifier equivalent circuit and compensation network the poles of this transfer function are (if c c >> c 0 + c p ): equation 3 equation 4 a 0 s ?? a v0 1s + r c c c ? ? ?? ? s 2 r 0 ? c 0 c p + ?? r c c c sr 0 c c ? r 0 c 0 c p + ?? r c c c ? + ? + ?? 1 + ? + ? ? ? ------------------------------------------------------------------------------------------------------------------------------- -------------------------------------------------------------------- = f p1 1 2 ? ? r 0 ? c c ? ------------------------------------- = f p2 1 2 ? ? r c ? c 0 c p + ?? ? ------------------------------------------------------- - =
closing the loop A5970D 18/41 docid13955 rev 7 whereas the zero is defined as: equation 5 f p1 is the low frequency which sets the bandwidth, while the zero f z1 is usually put near to the frequency of the double pole of the l-c filter (see below). f p2 is usually at a very high frequency. 7.2 lc filter the transfer function of the l-c filter is given by: equation 6 where r load is defined as the ratio between v out and i out . if r load >> esr, the previous expression of a lc can be simplified and becomes: equation 7 the zero of this transfer function is given by: equation 8 f 0 is the zero introduced by the esr of the ou tput capacitor and it is very important to increase the phase margin of the loop. the poles of the transfer function can be calculated through the following expression: equation 9 in the denominator of a lc the typical second order system equation can be recognized: equation 10 f z1 1 2 ? ? r c ? c c ? ------------------------------------- = a lc s ?? r load 1 esr c out s ? ? + ?? ? s 2 lc out esr r load + ?? s esr c out ? r load l + ? ?? r load + ? + ? ? ? ------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------------- = a lc s ?? 1 esr c out ? s ? + lc out ? s 2 esr c out ? s1 + ? + ? ---------------------------------------------------------------------------------------------- = f o 1 2 ? ? esr ? c out ? --------------------------------------------------- - = f plc1 2 ? esr c out esr c out ? ?? 2 4l ? c out ? ? ? ? ? 2l ? c out ? ------------------------------------------------------------------------------------------------------------------------------- ----------- = s 2 2 ? ?? n ? s ? 2 n + ? +
docid13955 rev 7 19/41 A5970D closing the loop 41 if the damping coefficient ? is very close to zero, the roots of the equation become a double root whose value is ? n . similarly for a lc the poles can usually be defined as a double pole whose value is: equation 11 7.3 pwm comparator the pwm gain is given by the following formula: equation 12 where v oscmax is the maximum value of a sawtooth waveform and v oscmin is the minimum value. a voltage feed forward is implemented to ensure a constant gpwm. this is obtained by generating a sawtooth waveform directly proportional to the input voltage v cc . equation 13 where k is equal to 0.076. therefore the pwm gain is also equal to: equation 14 this means that even if the input voltage changes, the error amplifier does not change its value to keep the loop in regulation, thus ensuring a better line regulation and line transient response. in summary, the open loop gain can be expressed as: equation 15 f plc 1 2 ? ? lc out ? ? ---------------------------------------------- = g pwm s ?? v cc v oscmax v oscmin ? ?? ------------------------------------------------------------- = v oscmax v oscmin ? kv cc ? = g pwm s ?? 1 k --- - const == gs ?? g pwm s ?? r 2 r 1 r 2 + -------------------- ? a o s ?? ? a lc ? s ?? =
closing the loop A5970D 20/41 docid13955 rev 7 example 1 considering r c = 4.7 k ? , c c = 22 nf and c p = 220 pf, the poles and zeroes of a 0 are: f p1 = 9 hz f p2 = 150 khz f z1 = 1.5 khz if l = 33 h, c out = 100 f and esr = 80 m ? , the poles and zeroes of a lc become: f plc = 2.7 khz f zesr = 19.89 khz finally r 1 = 5.6 k ? and r 2 = 3.3 k ? . the gain and phase bode diagrams are plotted respectively in figure 11 and figure 12 . figure 11. module plot figure 12. phase plot the cut-off frequency and the phase margin are: equation 16 f c 25khz = phase margin = 40
docid13955 rev 7 21/41 A5970D application information 41 8 application information 8.1 component selection ? input capacitor the input capacitor must be able to support the maximum input operating voltage and the maximum rms input current. since step-down converters draw current from the input in pulses, the input current is squared and the height of each pulse is equal to the output current. the input capacitor has to absorb all this switching curr ent, which can be up to the load current divided by two (worst case, with duty cycle of 50%). for this reason, the quality of these capacitors has to be very high to minimize the power dissipation generat ed by the internal esr, thereby improving system reliability and efficiency. the critical parameter is usually the rms current rating, which must be higher than the rms input current. the maximum rms input current (flowing through the input capacitor) is: equation 17 where ? is the expected system efficiency, d is the duty cycle and i o is the output dc current. this function reaches its maximum valu e at d = 0.5 and the equivalent rms current is equal to i o divided by 2 (considering ? = 1). the maximum and minimum duty cycles are: equation 18 and equation 19 where v f is the freewheeling diode forward voltage and v sw the voltage drop across the internal pdmos. considering the range d min to d max , it is possible to determine the max. irms going through the input capacitor. i rms i o d 2d 2 ? ? --------------- - ? d 2 ? 2 ------ - + ? = d max v out v f + v inmin v sw ? ------------------------------------ - = d min v out v f + v inmax v sw ? -------------------------------------- =
application information A5970D 22/41 docid13955 rev 7 capacitors that can be considered are: electrolytic capacitors: these are widely used due to their low pric e and their availabilit y in a wide range of rms current ratings. the only drawback is that, considering ripp le current rating requirements, they are physically larger than other capacitors. ceramic capacitors: if available for the required value and volt age rating, these capacitors usually have a higher rms current rating for a given ph ysical dimension (due to very low esr). the drawback is the considerably high cost. tantalum capacitors: very good, small tantalum capacitors with very low esr are becoming more available. however, they can occa sionally burn if subjected to very high current during charge. therefore, it is better to avoid this type of capacitor for the input filter of the device. they can, however, be subjected to high surge current when connected to the power supply. high dv/dt voltage spikes on the input side can be critical for dc/dc converters. a good power layout and input voltage filtering help to minimize this issue. in addition to the above considerations, a 1 ? f/50 v ceramic capacitor as close as possible to the vcc and gnd pins is always suggested to adequately filter vcc spikes. ? output capacitor the output capacitor is very important to meet the output voltage ripple requirement. using a small inductor value is useful to reduce the size of the choke but it increases the current ripple. so, to reduce the output voltage ripple, a low esr capacitor is required. nevertheless, the esr of the output capacitor introduces a zero in the open loop gain, which helps to increase the phase margin of the system. if the zero goes to a very high frequency, its effect is neglig ible. for this reason, ceramic capacitors and very low esr capacitors in general should be avoided. tantalum and electrolytic capacitors are usua lly a good choice for this purpose. a list of some tantalum capacitor manufacturers is provided in table 7: output capacitor selection . table 6. list of ceramic capacitors for the A5970D manufacturer series capacitor value ( f) rated voltage (v) taiyo yuden umk325bj106mm-t 10 50 murata grm42-2 x7r 475k 50 4.7 50
docid13955 rev 7 23/41 A5970D application information 41 ? inductor the inductor value is ve ry important as it fixes the ripple current flowing through the output capacitor. the ripple current is usually fixed at 20 - 40% of i omax , which is 0.2 - 0.4 a with i o max = 1 a. the approximate inductor value is obtained using the following formula: equation 20 where t on is the on time of the internal swit ch, given by d t. for example, with v out = 3.3 v, v in = 12 v and ? i o = 0.3 a, the inductor value is about 33 h. the peak current through the inductor is given by: equation 21 and it can be observed that if the inductor va lue decreases, the peak current (which must be lower than the current limit of the device) in creases. so, when the peak current is fixed, a higher inductor value allows a higher value for the output current. in table 8 some inductor manufacturers are listed. table 7. output capacitor selection manufacturer series cap. value ( f) rated voltage (v) esr (m ? ) sanyo poscap (1) 1. poscap capacitors have some characterist ics which are very similar to tantalum. tae 100 to 470 4 to 16 25 to 35 thb/c/e 100 to 470 4 to 16 25 to 55 avx tps 100 to 470 4 to 35 50 to 200 kemet t494/5 100 to 470 4 to 20 30 to 200 sprague 595d 220 to 390 4 to 20 160 to 650 table 8. inductor selection manufacturer series inductor value ( h) saturation current (a) coilcraft do3316t 15 to 33 2.0 to 3.0 coiltronics up1b 22 to 33 2.0 to 2.4 bi hm76-3 15 to 33 2.5 to 3.3 epcos b82476 15 to 33 2 to 3 wurth elektronik 74456115 15 to 33 2.5 to 3 l v in v out ? ?? ? i ---------------------------------- t on ? = i pk i o ? i 2 ----- + =
application information A5970D 24/41 docid13955 rev 7 8.2 layout considerations the layout of switching dc-dc converters is very important to minimize noise and interference. power-generating portions of the layout are the main cause of noise and so high switching current loop areas should be kept as small as possible and lead lengths as short as possible. high impedance paths (in particular the feedback connections) are susceptible to interference, so they should be as far as poss ible from the high curr ent paths. an layout example is provided in figure 13 . the input and output loops are minimized to avoid radiation and high frequency resonance problems. the feedback pin connections to the ex ternal divider are very close to the device to avoid pick-up noise. figure 13. layout example 8.3 thermal considerations the dissipated power of the device is tied to three different sources: ? conduction losses due to the not insignificant r dson , which are equal to: equation 22 where d is the duty cycle of the application. note th at the duty cycle is theoretically given by the ratio between v out and v in , but in practice it is substant ially higher than this value to compensate for the losses in the overall applic ation. for this reason , the switching losses related to the r dson increases compared to an ideal case. A5970D p on r dson i out ?? ? 2 d ? =
docid13955 rev 7 25/41 A5970D application information 41 ? switching losses due to turning on and off. these are derived using the following equation: equation 23 where t rise and t fall represent the switching times of the power element that cause the switching losses when driving an inductive load (see figure 14 ). t sw is the equivalent switching time. figure 14. switching losses ? quiescent current losses. equation 24 where i q is the quiescent current. example 2 ?v in = 12 v ?v out = 3.3 v ?i out = 1 a r ds(on) has a typical value of 0.25 at 25 c and increases up to a maximum value of 0.5 at 150 c. we can consider a value of 0.4 ? . t sw is approximately 70 ns. i q has a typical value of 2.5 ma at v in = 12 v. the overall losses are: equation 25 p sw v in i out t on t off + ?? 2 ----------------------------------- - ? ? f sw v in = ? i out t sw ? f sw ? ? = p q v in i q ? = p tot r dson i out ?? ? 2 dv in i out ? t sw ? f sw v in i q = ? + ? + ? = 0.4 1 2 ? 0.3 12 1 ? 70 ? 10 9 ? ? 250 ? 10 3 12 2.5 ? 10 3 ? ? + ? + ? 0.36w ? =
application information A5970D 26/41 docid13955 rev 7 the junction temperature of the device will be: equation 26 where t a is the ambient temperature and rth j-a is the thermal resistance junction to ambient. considering that the device is mounte d on board with a good ground plane, that it has a thermal resistance junction to ambient (rth j-a ) of about 120 c/w, and an ambient temperature of about 70 c: equation 27 8.4 short-circuit protection in overcurrent protection mode, when the peak current reaches the current limit, the device reduces the t on down to its minimum value (approximately 250 nsec) and the switching frequency to approximately one third of its nominal value even when synchronized to an external signal (see section 5.4: current protection on page 11 ). in these conditions, the duty cycle is strongly reduced and, in most app lications, this is enough to limit the current to ilim. in any event, in case of h eavy short-circuit at the output (v o = 0 v) and depending on the application conditions (v cc value and parasitic effect of external components) the current peak could reach values higher than ilim. this can be understood considering the inductor current ripple during the on and off phases: ? on phase equation 28 ? off phase equation 29 where v d is the voltage drop across the diode, dcr l is the series resistance of the inductor. in short-circuit conditions v out is negligible so during t off the voltage across the inductor is very small as equal to the voltage drop across parasitic components (typically the dcr of the inductor and the v fw of the free wheeling diode) while during t on the voltage applied the inductor is instead maximized as approximately equal to v in . so equation 28 and equation 29 in overcurrent conditions can be simplified to: equation 30 considering t on that has been already reduced to its minimum. t j t a rth ja ? p tot ? + = t j 70 0.36 120 110 ? c ? ? + = i l ton ? v in v out ? dcr l r dson + ?? i ? ? l ------------------------------------------------------------------------------------ t on ?? = i l toff ? v d v out dcr l i ? ++ ?? ? l --------------------------------------------------------------- t off ?? = i l ton ? v in dcr l r dson + ?? i ? ? l ---------------------------------------------------------------- t on min ?? v in l -------- - 250ns ?? ? =
docid13955 rev 7 27/41 A5970D application information 41 equation 31 considering that f sw has been already reduced to one third of the nominal. in case a short-circuit at the output is applied and v in = 12 v the inductor current is controlled in most of the applications (see figure 15 ). when the application must sustain the short-circuit condition for an extended period , the external components (mainly the inductor and diode) must be selected based on this value. in case the v in is very high, it could occur that the ripple current during t off ( equation 31 ) does not compensate the current increase during t on ( equation 30 ). the figure 17 shows an example of a power up phase with v in = v in max = 36 v where ?? il ton > ? il toff so the current escalates and the balance between equation 30 and equation 31 occurs at a current slightly higher than the current limit. this must be taken into account in particular to avoid the risk of an abrupt inductor saturation. figure 15. short-circuit current v in = 12 v figure 16. short-circuit current v in = 24 v i l toff ? v d v out dcr l i ? ++ ?? ? l --------------------------------------------------------------- 3t ? sw ?? v d v out dcr l i ? ++ ?? ? l --------------------------------------------------------------- 12 ? s ?? ? =
application information A5970D 28/41 docid13955 rev 7 figure 17. short-circuit current v in = 36 v
docid13955 rev 7 29/41 A5970D application information 41 8.5 application circuit figure 18 shows the evaluation board application ci rcuit, where the input supply voltage, v cc , can range from 4 v to 36 v and the output voltage is adjustable from 1.235 v to 6.3 v due to the voltage rating of the output capacitor. figure 18. evaluation board application circuit table 9. component list reference part number description manufacturer c1 grm42-2 x7r 475k 50 4.7 f, 50 v murata c2 poscap 6tae330ml 330 f, 6.3 v sanyo c3 c1206c221j5gac 47 pf, 5%, 50 v kemet c4 c1206c223k5rac 22 nf, 10%, 50 v kemet r1 5.6 k ? , 1%, 0.1 w 0603 neohm r2 3.3 k ? , 1%, 0.1 w 0603 neohm r3 22 k ? , 1%, 0.1 w 0603 neohm d1 stps3l40u 2 a, 40 v stmicroelectronics l1 do3316t-333mld 33 h, 2.1 a coilcraft A5970D l1 33uh
application information A5970D 30/41 docid13955 rev 7 figure 19. pcb layout (component side) figure 20. pcb layout (bottom side) figure 21. pcb layout (front side)
docid13955 rev 7 31/41 A5970D application information 41 8.6 positive buck-boost regulator the device can be used to implement a step -up/down converter with a positive output voltage. the output voltage is given by: equation 32 where the ideal duty cycle d for the buck boost converter is: equation 33 however, due to power losses in the passive el ements, the real duty cycle is always higher than this. the real value (that can be measured in the application) should be used in the following formulas. the peak current flowing in the embedded switch is: equation 34 while its average cu rrent is equal to: equation 35 this is due to the fact that th e current flowing through the internal power switch is delivered to the output only during the off phase. the switch peak current must be lower than the minimum current limit of the overcurrent protection (see table 4: electrical characteristics on page 6 for details) while the average current must be lowe r than the rated dc cu rrent of the device. as a consequence, the maxi mum output current is: equation 36 where i sw ma x represents the rated current of the device. the current capability is reduced by the term (1 - d) and so, for example, with a duty cycle of 0.5, and considering an average current through the switch of 1 a, the maximum output current deliverable to the load is 0.5 a. v out v in d 1d ? ------------- ? = d v out v in v out + ----------------------------- - = i sw i load 1d ? --------------- i ripple 2 ------------------- - + i load 1d ? --------------- v in 2l ? ---------- - d f sw --------- ? + == i sw i load 1d ? --------------- = i out max i sw max 1d ? ?? ? ?
application information A5970D 32/41 docid13955 rev 7 figure 22 shows the schematic circuit of this topology for a 12 v output voltage and 5 v input. figure 22. positive buck-boost regulator
docid13955 rev 7 33/41 A5970D application information 41 8.7 negative buck-b oost regulator in figure 23 , the schematic circuit for a standard buck -boost topology is shown. the output voltage is: equation 37 where the ideal duty cycle d for the buck boost converter is: equation 38 the considerations given in section 8.6 for the real duty cycle are still valid here. also the equation 34 till equation 36 can be used to calculate the maximum output current. so, as an example, considering the conversion v in = 12 v to v out = -5 v, i load = 0.2 a: equation 39 equation 40 an important thing to take into account is that the ground pin of the device is connected to the negative output voltage. therefore, the device is subjected to a voltage equal to v in - v o , which must be lower than 36 v (the maximum operating input voltage). figure 23. negative buck-boost regulator v out v in ? d 1d ? ------------- ? = d v ? out v in v out ? ----------------------------- - = d 5 512 + --------------- - 0.706 == i sw i load 1d ? --------------- 0.2 10.706 ? ----------------------- - 0.7a == = A5970D -12v/0.3a
application information A5970D 34/41 docid13955 rev 7 8.8 synchronization example see section 5.3: oscillator and synchronization on page 10 for details. figure 24. synchronization example 8.9 compensation network with mlcc at the output mlccs (multiple layer ceramic capacitor) with values in the range of 10 f - 22 f and rated voltages in the range of 10 v - 25 v are available today at relatively low cost from many manufacturers. these capacitors have very low esr values (a few m ? ) and thus are occasionally used for the output filter in order to reduce the voltage ripple and the overall size of the application. however, a very low esr value affect s the compensation of the loop (see section 7: closing the loop on page 16 ) and in order to keep the system stable, a more complicated compensation network may be required. however, due to the architecture of the internal error amplifier the bandwidth with this compensation is limited. that is why output capacitors with a not negligible esr are suggested. the selection of the output capacitor have to guarantee that the zero introduced by this co mponent is inside the designed system bandwidth and close to the fr equency of the double pole introduced by the lc filter. a general rule for th e selection of this compound for the system stability is provided in equation 41 . equation 41 A5970D A5970D f z esr 1 2 ? esr c out ?? ? ----------------------------------------------- - = bandwidth ? f lc f ? z esr 10 f lc ? ?
docid13955 rev 7 35/41 A5970D application information 41 figure 25 shows an example of a compensation net work stabilizing the system with ceramic capacitors at the output (the optimum co mponent value depends on the application). figure 25. mlcc compensation network example 8.10 external soft_start network at a startup the device can quickly increase the current up to the curr ent limit in order to charge the output capacitor. if soft ramp-up of the output voltage is required, an external soft-start network can be implemented as shown in figure 26 . the capacitor c is charged up to an external reference through r and the bjt clamps the comp pin. this clamps the duty cycle, limiting the slew rate of the output voltage. figure 26. soft-start network example A5970D
typical characteristics A5970D 36/41 docid13955 rev 7 9 typical characteristics figure 27. line regulation figure 28. load regulation figure 29. output voltage vs. junction temperature figure 30. switching frequency vs. junction temperature figure 31. quiescent current vs. junction temperature figure 32. shutdown current vs. junction temperature 3.276 3.28 3.284 3.288 3.292 3.296 3.3 3.304 3.308 3.312 00.511.5 io (a) vo (v) tj = 125c tj = 25c vcc = 12v vo = 3.3v
docid13955 rev 7 37/41 A5970D typical characteristics 41 figure 33. junction temperature vs. output current - v in = 5 v figure 34. junction temperature vs. output current - v in = 12 v figure 35. efficiency vs. output current - v in = 5 v figure 36. efficiency vs. output current - v in = 12 v
package information A5970D 38/41 docid13955 rev 7 10 package information in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack specifications, grade definitions a nd product status are available at: www.st.com . ecopack is an st trademark. figure 37. so-8 package outline
docid13955 rev 7 39/41 A5970D package information 41 table 10. so-8 package mechanical data symbol dimensions mm inch min. typ. max. min. typ. max. a 1.35 1.75 0.053 0.069 a1 0.10 0.25 0.004 0.010 a2 1.10 1.65 0.043 0.065 b 0.33 0.51 0.013 0.020 c 0.19 0.25 0.007 0.010 d (1) 1. dimensions d does not include mold flash, protrusions or gate burrs. mold flash, p r otrusions or gate burrs shall not exceed 0.15 mm (.006 inch) in total (both sides). 4.80 5.00 0.189 0.197 e 3.80 4.00 0.15 0.157 e 1.27 0.050 h 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 l 0.40 1.27 0.016 0.050 k 0 (min.), 8 (max.) ddd 0.10 0.004
revision history A5970D 40/41 docid13955 rev 7 11 revision history table 11. document revision history date revision changes 06-aug-2007 1 initial release. 24-oct-2007 2 updated: table 4 on page 5 2-may-2008 3 updated cover page, table 4 on page 5 27-aug-2008 4 updated cover page and table 4 on page 5 22-apr-2009 5 updated first feature in coverpage 03-nov-2009 6 updated table 4 on page 6 and added figure 28 on page 36 . 28-mar-2014 7 updated table 4: electrical characteristics on page 6 (added value ? ? ? to ?r l ? in ?error amplifier? part). updated section 8.1: component selection on page 21 ( table 6 : updated units in ?capacitor value?, added text below table 6 ). updated titles from figure 33 to figure 36 (added values of ?v in ?). updated section 10: package information on page 38 (reversed order of figure 37 and table 10 , updated titles, minor modifications). updated cross-references throughout document. minor modifications throughout document.
docid13955 rev 7 41/41 A5970D 41 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems wi th product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2014 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com


▲Up To Search▲   

 
Price & Availability of A5970D

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X