|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
pcqa-bfs1 pcqa24 specifcations output voltage current resolution refer to output specifcation sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection connector m12, 8 pin / cable 2 m emc, temperature refer to output specifcation posichron ? position sensor in square profle ? protection class up to ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? easy installation with mounting brackets ? wear free position magnet ? contactless ? also available with guided position magnet ? analog output order code mounting set (see page 7) posichron ? pcqa24 square profile housing with analog output 1 channel order code pcqa24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output u1 = 0 ... 10 v signal conditioner u1/h = u1 with alarm_hold (see page 11) u2 = 0.5 ... 10 v signal conditioner u2/u; u2/h = u2 with alarm_low; u2 with alarm_hold (see page 11) u8 = 0.5 ... 4.5 v signal conditioner u8/u; u8/h = u8 with alarm_low; u8 with alarm_hold (see page 11) i1 = 4 ... 20 ma signal conditioner (3 wire) i1/u; i1/h = i1 with alarm_low; i1 with alarm_hold (see page 11) function and characteristics output p1a = position magnet 1, increasing p1d = position magnet 1, decreasing pmu = start value, direction & end value adjustable by the customer linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection m12 = connector m12, 8 pin kab2m = cable, standard length 2 m, other lengths upon request db-pcqa24-e-2013-11 www.asm-sensor.com 1/16 ? asm gmbh info@asm-sensor.com
kab-...m-m12/8f/g-litze pcmag ... pcqa24 order code mating connecting cable (see page 15) order code position magnet/slider (see page 8) posichron ? pcqa24 square profile housing with analog output 1. order example: pcqa24 - 1000 - i1 - p1a - p2d - l10 - m12 square profle, measurement range 1000 mm, 2 current outputs 4 ... 20 ma (i1) output 1: position magnet 1, increasing signal (p1a) output 2: position magnet 2, decreasing signal (p2d) 2. order example: pcqa24 - 1000 - u1 - p1a - vz1.0 - l10 - m12 square profle, measurement range 1000 mm, 2 voltage outputs 0.5 ... 10 v (u2) output 1: position magnet 1, increasing signal (p1a) output 2: velocity magnet 1, -1 m/s ... 1 m/s for range 0.5 ... 10 v (vz1.0) order code pcqa24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output u1 = 0 ... 10 v signal conditioner u1/h = u1 with alarm_hold (see page 11) u2 = 0.5 ... 10 v signal conditioner u2/u; u2/h = u2 with alarm_low; u2 with alarm_hold (see page 11) u8 = 0.5 ... 4.5 v signal conditioner u8/u; u8/h = u8 with alarm_low; u8 with alarm_hold (see page 11) i1 = 4 ... 20 ma signal conditioner (3 wire) i1/u; i1/h = i1 with alarm_low; i1 with alarm_hold (see page 11) function and characteristics output 1 p1a = position magnet 1, increasing p1d = position magnet 1, decreasing da = difference magnet 1/2, increasing (2 magnets required) dd = difference magnet 1/2, decreasing (2 magnets required) function and characteristics output 2 p2a = position magnet 2, increasing p2d = position magnet 2, decreasing da = difference magnet 1/2, increasing dd = difference magnet 1/2, decreasing vzx.x = velocity with direction detection (with 1 magnet only) vzx.x = velocity in steps of 0.1 m/s example: vz1.5 towards start position towards end position -1.5 m/s 0 +1.5 m/s output u2: 0.5 v 5.25 v 10 v output i1: 4 ma 12 ma 20 ma vax.x = velocity without direction detection (with 1 magnet only) vax.x = velocity in steps of 0.1 m/s example: va1.5 towards start position towards end position -1.5 m/s 0 +1.5 m/s output u2: 10 v 0.5 v 10 v output i1: 20 ma 4 ma 20 ma linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection m12 = connector m12, 8 pin kab2m = cable, standard length 2 m, other lengths upon request 2 channel, confgurable 2 magnets required db-pcqa24-e-2013-11 www.asm-sensor.com 2/16 ? asm gmbh info@asm-sensor.com kab-...m-m12/8f/g-litze pcqa-bfs1 pcmag ... / / pcqa24 / / specifcations output synchronous serial interface (ssi) resolution 5, 10, 20, 50, 100 m sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection 8 pin socket / cable 2 m emc, temperature refer to output specifcation posichron ? position sensor in square profle ? protection class ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? easy installation with mounting brackets ? wear free position magnet ? contactless ? also available with guided position magnet ? synchronous serial interface (ssi) order code position magnet/slider (see page 8) order code mounting set (see page 7) order example: pcqa24 - 2500 - 10 - ssi/g/24 - l10 - m12 order code mating connecting cable (see page 15) posichron ? pcqa24 square profile housing with ssi output order code pcqa24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request resolution (in m) 5 / 10 / 20 / 50 / 100 output ssi = synchronous serial interface code g / d = gray / dual number of data bits 24 / 25 linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection m12 = connector m12, 8 pin kab2m = cable, standard length 2 m, other lengths upon request db-pcqa24-e-2013-11 www.asm-sensor.com 3/16 ? asm gmbh info@asm-sensor.com pcmag ... pcqa-bfs1 kab-...m-m12/5f/g-m12/5m/g - can pcqa24 posichron ? pcqa24 square profile housing with can output posichron ? position sensor in square profle ? protection class ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? easy installation with mounting brackets ? wear free position magnet ? contactless ? also available with guided position magnet ? canopen bus or can sae j1939 output specifcations output canopen bus; can sae j1939 resolution 50 m sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection 5 pin socket m12 emc, temperature refer to output specifcation order code bus cable (see page 16) order code position magnet/slider (see page 8) order code mounting set (see page 7) order example: pcqa24 - 1000 - canop - l10 - m12/can order code pcqa24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output canop = canopen bus canop/r = canopen-bus with integrated terminating resistance canj1939 = can sae j1939 linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection m12/can = connector m12, 5 pin db-pcqa24-e-2013-11 www.asm-sensor.com 4/16 ? asm gmbh info@asm-sensor.com posichron ? pcqa24 square profile housing cable output connector m12 cable: outer diameter 5.2 mm 0.2 mm, wire: cross sectional area 0.25 mm2 status ?nderungen datum name datu m name gezeichnet kontrolliert norm a s m a utomation s ensorik m esstechnik asm gmbh am bl eichb ach 18 -22 d-854 52 mo os inning tel .: 08123/986-0 allgemeintoleranzen ma?stab bmc: benennung wer ks toff, ha lbzeug ct: zeichnungsnummer / datei blatt nicht bema?te werk st ckka nten din 6 784 -0,1 -0,2 +0,1 +0,2 1 21 40 4_pcqa24 -ml (1 00-5 75 0)-m12_ 003 _l mz .i dw 29.11.2009 scf 1 a4 iso 1:1 ma? zei ch nung / general drawing 27 68 -mh pc qa24-ml(10 0- 5750 )- (10 v| 420t)-m12 zeichnung ist eigentum der firma asm, vervielf?ltigung nur mit genehmigung sc hutz ve rmerk nach di n 34 be achten ? copyright by asm gmbh ma?e in mm [inch] dimensions in mm [inch] 10,2 [. 40 2] 3 7 , 2 5 [ 1 . 4 6 7 ] st art position pcmag5 end position pcma g5 85 [3.3 46] measurement length (e .g .100 [3.937]) 70 [2 .75 6] total length a = measurement length + 1 55 [6.1 02] (e .g. 255 [10. 03 9]) mounting set pcq a-b fs1 3 5 , 5 [ 1 .3 9 8 ] 39 [1 .535] 26 [1 .024] 5 4 , 2 5 [ 2 . 1 3 6 ] 5 9 , 2 5 [2 . 3 3 3 ] 46 [1.8 11] 58 [2.2 83] 2 ? 1 .0 7 9 ? .0 3 9 [ ] 12 [. 47 2] 15,95 [.628] status ?nderungen datum name datu m name gezeichnet kontrolliert norm a s m a utomation s ensorik m esstechnik asm gmbh am bl eichb ach 18 -22 d-854 52 mo os inning tel .: 08123/986-0 allgemeintoleranzen ma?stab bmc: benennung wer ks toff, ha lbzeug ct: zeichnungsnummer / datei blatt nicht bema?te werk st ckka nten din 6 784 -0,1 -0,2 +0,1 +0,2 1 21 40 4_pcqa24 -ml (1 00-5 75 0)-kab_0 01_jm z.idw 11.05.2005 scf 1 a4 iso 1:2 m a? zei chn ung 27 68 -mh pc qa24-ml(10 0- 5750)-(10|420t)-kab ze ichnung ist eigentum d er firma asm, ve rvielf ?ltig ung nur mit ge nehm ig ung sc hutz ve rmerk nach di n 34 be achten ? copyright by asm gmbh 85 [3. 346] 46 [1.811] 58 [2.283] 5 4 ,2 5 [2 . 1 3 6 ] 5 9 , 2 5 [2 .3 3 3 ] 26 [1. 024] 39 [1. 535] 10,2 [0. 402] mounting set pc qa-bfs1 start position pcma g5 e nd posi tion pc mag5 ma?e in mm [i nch] 2 1 [ 0 . 0 7 9 0 . 0 3 9 ] measurement length (e .g. 100 [3. 93 7]) 70 [2 .756] total length a = measurement length + 155 [6.102] (e .g. 255 [10 .039]) 12 [0.472] 20,9 [0. 82 3] 3 7 , 2 5 [1 . 4 6 7 ] 3 5 , 5 [ 1 .3 9 8 ] dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] db-pcqa24-e-2013-11 www.asm-sensor.com 5/16 ? asm gmbh info@asm-sensor.com with magnet pcmag3 posichron ? pcqa24 square profile housing status ?nderungen datum name datu m name gezeichnet kontrolliert norm a s m a utomation s ensorik m esstechnik asm gmbh am bl eichb ach 18 -22 d-854 52 mo os inning tel .: 08123/986-0 allgemeintoleranzen ma?stab bmc: benennung wer ks toff, ha lbzeug ct: zeichnungsnummer / datei blatt nicht bema?te werk st ckka nten din 6 784 -0,1 -0,2 +0,1 +0,2 1 21 40 4_pcqa24 -(1 00 -5750) -m 12- pcqa bf s1 +p cm ag 3_00 2_a mz. idw 22.04.2008 wa neck 1 a4 iso 1:1 genera l drawing 27 68 -mh pcqa 24 + zu beh?r ze ichnung ist eigentum d er firma asm, ve rvielf ?ltig ung nur mit ge nehm ig ung sc hutz ve rmerk nach di n 34 be achten ? copyright by asm gmbh 85 [3.348] 70 [2 .75 7] 3 5 ,5 [ 1 .3 9 8 ] 46 [1.8 11] 3 8 ,3 [ 1 .5 0 6 ] 6 4 ,5 [ 2 . 5 3 9 ] 58 [2.2 83] pcmag3 pc mag3 15,95 [0. 628] di mensi ons in mm [i nch] 5 8 [ 2 .2 8 3 ] 3 9 , 1 [ 1 .5 4 ] 28,3 [1.11] measur eme nt length (e.g. 1 00 [3. 93 7]) total leng th a = me asurement leng th + 155 [6. 102] (e .g. 255[10.041]) 28 ,3 [1.11] 2 6 , 3 [ 1 .0 3 ] 1 9 , 8 [ 0 . 7 8 ] st art po si tion end position pcqa-b fs1 mo un ting set dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] db-pcqa24-e-2013-11 www.asm-sensor.com 6/16 ? asm gmbh info@asm-sensor.com 58 46 35 [1 .378] 4 4 [ 1 . 7 3 2 ] 2 4 , 6 5 [ . 9 7 ] 2 6 ,5 [ 1 . 0 4 3 ] 26,6 [1.047] 25 [.984] ? 55 [2.165] 25 [.984] 20 [.787] 1 7 , 5 [ .6 8 9 ] 4 2 , 5 [ 1 . 6 7 3 ] 5 [ . 1 9 7 ] 5 [ .1 9 7 ] 2 [.079] 4x r2, 75 [.108] posichron ? pcqa mounting sets mounting set pcqa-bfs1 with mounting clamps option -bfw mounting brackets for pcqa22 and pcqa24 note: the option -bfw can only be ordered with a new sensor, not separately! applicable for sensor lengths up to 1000 mm. isolation strip mounting clamp p isolation sleeve dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] order example: pcqa24 - 1000 - u2 - p1a - l10 - m12 - bfw db-pcqa24-e-2013-11 www.asm-sensor.com 7/16 ? asm gmbh info@asm-sensor.com 28, 25 [ 1.1 12] 39 [1 .53 5] 9 ,6 [ 0 .3 7 8 ] 2 6 [ 1 .0 1 2 ] 1 6 [ 0 .6 3 0 ] 78 [3.0 71 ] mit ein geset ztem mag net m5 85 [3.346] 70 [2.763] mess l? nge (z.b. 100 [3.93 7]) gesam tl?nge a = messl?nge + 1 55 [ 6.102] (z.b. 255 [ 10.0 41 ]) 3 5 ,5 [ 1 .3 9 8 ] 46 [1.8 11] 58 [2.2 83] 5 4 ,2 5 [ 2 .1 3 6 ] 5 9 ,2 5 [ 2 . 3 3 3 ] 3 7 ,2 5 [ 1 .4 6 7 ] 26 [1. 024 ] 39 [1.535] 10,2 [0.402] befe stigungssatz pcq a-bfs1 anfa ngsp osition pcmag5 en dposition pcmag5 16 [0.630] 12 [0 .472] ? 2 1 [ 0 .0 7 9 0 .0 3 9 ] posichron ? pcqa mounting sets - magnets pcmag3 guided magnet slider with internal position magnet pcmag5 standard magnet internal magnet dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] db-pcqa24-e-2013-11 www.asm-sensor.com 8/16 ? asm gmbh info@asm-sensor.com i1 u1, u2, u8 posichron ? output specification u2, u8 and i1 configurable, 1 or 2 channels u1, u2, u8 voltage output excitation voltage u1: 18 ... 36 v dc; u2: 18 ... 36 v dc; u8: 10 ... 36 v excitation current typ. 35 ma, 80 ma max. output voltage u1: 0 ... 10 v dc; u2: 0.5 ... 10 v dc; u8: 0.5 ... 4.5 v dc output current 2 ma max. output load > 5 k? resolution 16 bit f.s., min. 10 m stability (temperature) 50 x 10 -6 / c f.s. protection reverse polarity, short circuit output noise 0.5 mv rms operating temperature -40 ... +85 c emc en 61326-1:2013 excitation + excitation gnd signal 1 + signal gnd signal diagram excitation + excitation gnd signal 1 + signal gnd i1 current output (3 wire) excitation voltage 18 ... 36 v dc (10 ... 36 v for r l 250?) excitation current typ. 60 ma, 80 ma max. load resistor 350 ? max. output current 4 ... 20 ma, 30 ma max (at failure) resolution 16 bit f.s., min. 10 m stability (temperature) 50 x 10 -6 / c f.s. protection reverse polarity, short circuit output noise 0.5 mv rms operating temperature -40 ... +85 c emc en 61326-1:2013 span/zero (pmu, as option) signal 2 + (as option) span/zero (pmu, as option) signal 2 + (as option) signal diagram signal diagram db-pcqa24-e-2013-11 www.asm-sensor.com 9/16 ? asm gmbh info@asm-sensor.com posichron ? output specification u2, u8 and i1 configurable, 1 or 2 channels signal plug connection cable connection view to the sensor connector excitation + 1 white excitation gnd 2 brown signal 1 + 3 green signal gnd 4 yellow signal 2 + (optional*) 5 grey span/zero (pmu** only, optional) 6 pink connector m12, 8-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 11 signal plug connection view to the sensor connector excitation + 1 signal 1 + 2 gnd 3 signal 2 + (optional*) 4 pmu** (optional) 5 connector m12, 5-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 11 signal plug connection view to the sensor connector excitation + 1 excitation gnd 2 signal + 3 pmu** (optional) 4 connector m8, 4-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 11 db-pcqa24-e-2013-11 www.asm-sensor.com 10/16 ? asm gmbh info@asm-sensor.com option - pmu for analog output u1, u2, u8 and i1 programming of the start and end value by the customer: the option pmu allows to program the start value and the end value of the output range by a programming signal span/zero available at the connector. this signal span/zero must be connected with gnd via a push button, then position magnet of the sensor must be moved to the start resp. end position. pushing the button between 2 and 4 seconds sets the actual position as start position, pushing the button more than 5 seconds sets the actual position as end position. the values will be stored and are available after switching off the sensor. to reset the sensor to the factory values the button must be pushed for longer than two seconds when the sensor is switched on. posichron ? description of output options diagnostic on analog outputs error signal for ssi output if the sensor cannot detect a magnet the position value will assume the maximum value (0xfffffff). alarm_high (standard) alarm_low (.../u) alarm_hold (.../h) u1 u out 10,5 v keeps last valid state ( order code u1/h) u2 u out 10,5 v u out < 0,25 v ( order code u2/u) keeps last valid state ( order code u2/h) u8 u out 10 v u out < 0,25 v ( order code u8/u) keeps last valid state ( order code u8/h) i1 i out 21 ma 1,5 ... 2 ma (order code i1/u) keeps last valid state ( order code i1/h) behaviour of the analog signal output in case of error in case of error (magnet missing or outside the measuring range) the analog output signal will assume a state according to the following options: alarm_high the output voltage resp. the output current is at high level (overrange). alarm_low the output voltage resp. the output current is at low level (underrange). alarm_hold the output voltage resp. the output current will keep the last valid state. db-pcqa24-e-2013-11 www.asm-sensor.com 11/16 ? asm gmbh info@asm-sensor.com posichron ? output specification ssi description the data transmission takes place by means of the two signals clock and data. the pro - cessing unit (plc, microcomputer) sends pulse sequences which clock the data transmissi - on at the required transfer rate. with the first falling edge of the pulse sequence the position of the sensor is recorded and stored. the following rising edges control the bit-by-bit transfer of the data word. after a delay time the next new position information can be transwithted. data format (train of 26 pulses) synchronous serial interface ssi output rs422 excitation voltage 10 ... 36 v dc, residual ripple 10 mv ss excitation current typ. 80 ma, 150 ma max. clock frequency 100 khz ... 1 mhz code gray code, dual code resolution 5 m delay between pulse trains >25 s stability (temperature) 50 x 10 -6 / c f.s. operating temperature -40 ... +85 c emc en 61326-1:2013 sensor circuit subsequent circuit cable length baud rate 50 m 100-1000 khz 100 m 100-300 khz note: extension of the cable length will reduce the maximum transmission rate. the signals clock/clock and data/ data must be connected in a twisted pair cable, common shielded. clock clock data data signal diagram error indication see page 11. signal wiring signal plug connection cable connection view to sensor connector excitation + 1 white excitation gnd 2 brown clock 3 green clock 4 yellow data 5 grey data 6 pink db-pcqa24-e-2013-11 www.asm-sensor.com 12/16 ? asm gmbh info@asm-sensor.com view to sensor connector posichron ? output specification canopen interface canop communication profle canopen cia 301 v 4.02, slave encoder profle encoder cia 406 v 3.2 error control node guarding, heartbeat, emergency message node id adjustable via lss or via object dictionary pdo 4 txpdo, 0 rxpdo, no linking, static mapping pdo modes event-/time triggered, remote-request, sync cyclic/acyclic sdo 1 server, 0 client cam 8 cams certifed yes transmission rates 50 kbaud to 1 mbaud, adjustable via lss or via object dictionary nodes 127 max. bus connection m12 connector, 5 pins integrated bus terminating resistor 120 ? (option) bus, galvanic isolated no description canopen interface with process data for position and cam functions, programmable are preset, resolution, filtering and cam switching points. specifcations excitation voltage 18 ... 36 v dc excitation current typ. 20 ma for 24 v, max. 80 ma number of position magnets 1 ... 4 resolution 50 m measuring rate 1 khz (asynchronous) stability (temperature) 50 x 10 -6 / c f.s. repeatability 1 lsb operating temperature -40 ... +85 c protection reverse polarity, short circuit dielectric strength 500 v (v ac, 50 hz, 1 min.) emc en 61326-1:2013 signal wiring signal plug connection shield 1 excitation + 2 gnd 3 can-h 4 can-l 5 when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. db-pcqa24-e-2013-11 www.asm-sensor.com 13/16 ? asm gmbh info@asm-sensor.com posichron ? output specification can sae j1939 interface j1939 can specifcation iso 11898, basic and full can 2.0 b transceiver 24v-compliant, not isolated communication profle sae j1939 baud rate 250 kbit/s internal temination resistor 120 ? (option) address default 247d, confgurable specifcations excitation voltage 18 ... 36 v dc excitation current typ. 20 ma for 24 v, max. 80 ma measuring rate 1 khz (asynchronous) stability (temperature) 50 x 10 -6 / c f.s. repeatability 1 lsb operating temperature -40 ... +85 c protection reverse polarity, short circuit dielectric strength 500 v (v ac, 50 hz, 1 min.) emc en 61326-1:2013 signal wiring signal plug connection shield 1 excitation + 2 gnd 3 can-h 4 can-l 5 name fields arbitrary address capable 0 no industry group 0 global vehicle system 7fh (127d) non specifc vehicle system instance 0 function ffh (255d) non specifc function instance 0 ecu instance 0 manufacturer 145h (325d) manufacturer id identity number 0nnn serial number 21 bit parameter group numbers (pgn) confguration data pgn ef00h proprietary-a (pdu1 peer-to-peer) process data pgn ffnnh proprietary-b (pdu2 broadcast); nn group extension (ps) confgurable view to sensor connector when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. db-pcqa24-e-2013-11 www.asm-sensor.com 14/16 ? asm gmbh info@asm-sensor.com kab - xm - m12/8f/w - litze kab - xm - m12/8f/w/69k - litze ip69k: kab - xm - m12/5f/g/69k - litze kab - xm - m12/5f/g - litze kab - xm - m12/5f/w/69k - litze kab - xm - m12/5f/w - litze kab - xm - m12/8f/g - litze kab - xm - m12/8f/g/69k - litze ip69k: ip69k: ip69k: posichron ? accessories connector cables connector cable m12, 8-pin shielded the 8-lead shielded cable is supplied with a mating 8-pin 90 m12 connector at one end and 8 wires at the other end. available lengths are 2, 5 and 10 m. wire: cross sectional area 0.25 mm2. order code: length in m signal wiring m12, 8-pin plug connection / cable connection 1 2 3 4 5 6 7 8 white brown green yellow grey pink blue red connector cable m12, 8-pin shielded the 8-lead shielded cable is supplied with a mating 8-pin m12 connector at one end and 8 wires at the other end. available lengths are 2, 5 and 10 m. wire: cross sectional area 0.25 mm2. order code: length in m connector cable m12, 5-pin shielded the 5-lead shielded cable is supplied with a mating 5-pin 90 m12 connector at one end and 5 wires at the other end. available lengths are 2 m, 5 m and 10 m. wire: cross sectional area 0.34 mm 2 . order code: length in m connector cable m12, 5-pin shielded the 5-lead shielded cable is supplied with a mating 5-pin m12 connector at one end and 5 wires at the other end. available lengths are 2 m, 5 m and 10 m. wire: cross sectional area 0.34 mm 2 . order code: length in m signal wiring m12, 5-pin plug connection / cable connection 1 2 3 4 5 brown white blue black grey 15/16 ? asm gmbh info@asm-sensor.com db-pcqa24-e-2013-11 www.asm-sensor.com kab - xm - m12/5f/g - m12/5m/g - can kab - xm - m12/5f/g/69k - m12/5m/g/69k - can ip69k: kab - tconn - m12/5m - 2m12/5f - can kab - rterm - m12/5m/g - can posichron ? accessories connector cables connector/bus cable m12, 5-pin can bus shielded the 5-lead shielded cable is supplied with a female 5-pin m12 connector at one end and a male 5-pin m12 connector at the other end. available lengths are 0.3 m, 2 m, 5 m and 10 m. order code: length in m terminating resistance m12, 5-pin can bus t-piece for bus cable m12, 5-pin can bus order code: order code: db-pcqa24-e-2013-11 www.asm-sensor.com 16/16 ? asm gmbh info@asm-sensor.com |
Price & Availability of PCQA24-5750-U2-PMU-L02 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |