www.rfm.com e-mail: info@rfm.com page 1 of 4 ? 2012 by rf monolithics, inc. SF2315E - 10/29/12 electrical characteristics electrical connections characteristic sym notes min typ max units center frequency f c 782 mhz insertion loss, 777 to 787 mhz il 2.2 3.0 db bandwidth 10 25 mhz amplitude ripple, 777 to 787 mhz 0.35 1.00 db p-p attenuation, referenced to 0 db: db 300 to 700 mhz 28 61 728 to 757 mhz 10 48 880 to 1050 mhz 28 61 source impedance z s 50 ? load impedance z l 50 ? case style sm3030-6 3.0 x 3.0 mm nominal footprint lid symbolization (y=year, ww=week, s= shift) dot=pin 1 indicator a72, ywws standard reel quantity reel size 7 inch 500 pieces/reel reel size 13 inch 3000 pieces/reel connection terminals input 2 output 5 case ground all others sm3030-6 ? low-loss 782 mhz saw filter ? designed for 50 ohm source/load ? complies with directive 2002/95/ec (rohs) absolute maximum ratings rating value units input power level +25 dbm dc voltage on any non-ground terminal 3 v operating temperature range -40 to +85 c storage temperature range in tape and reel -40 to +85 c maximum soldering profile, 5 cycles/10 seconds maximum 265 c 782 mhz saw filter SF2315E 1. unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified d emonstration board with impedance matching to 50 ? and measured with 50 ? network analyzer. 2. unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. rejection is measured as attenuation below the minimum il point in the passband. rejection in final user application is depen dent on pcb layout and external impedance matching design. see application note no. 42 for details. 4. "lrip" or "l" after the part number indicates "low rate initial production" and "eng" or "e" indicates "engineering prototype s." 5. the design, manufacturing process, and specifications of this filter are subject to change. 6. either port 1 or port 2 may be used for either input or output in the design. however, impedances and impedance matching may vary between port 1 and port 2, so that the filter must always be installed in one direction per the circuit design. 7. us and international patents may apply. 8. rfm, stylized rfm logo, and rf monolithics, inc. are registered trademarks of rf monolithics, inc. pb caution: electrostatic sensitive device. observe precautions for handling. notes: preliminary
www.rfm.com e-mail: info@rfm.com page 2 of 4 ? 2012 by rf monolithics, inc. SF2315E - 10/29/12 filter response plots
www.rfm.com e-mail: info@rfm.com page 3 of 4 ? 2012 by rf monolithics, inc. SF2315E - 10/29/12 sm3030-6 case top view bottom view 1 2 3 6 5 4 1 2 3 6 5 4 a bc d j ef gh i 6-terminal ceramic surface-mount case 3.0 x 3.0 mm nominal footprint case and pcb footprint dimensions case materials dimension mm inches min nom max min nom max a 2.87 3.00 3.13 0.113 0.118 0.123 b 2.87 3.00 3.13 0.113 0.118 0.123 c 1.12 1.25 1.38 0.044 0.049 0.054 d 0.77 0.90 1.03 0.030 0.035 0.040 e 2.67 2.80 2.93 0.105 0.110 0.115 f 1.47 1.60 1.73 0.058 0.063 0.068 g 0.72 0.85 0.98 0.028 0.033 0.038 h 1.37 1.50 1.63 0.054 0.059 0.064 i 0.47 0.60 0.73 0.019 0.024 0.029 j 1.17 1.30 1.43 0.046 0.051 0.056 k 3.20 0.126 l 1.70 0.067 m 1.05 0.041 n 0.81 0.032 o 0.38 0.015 materials solder pad plating 0.3 to 1.0 m gold over 1.27 to 8.89 m nickel lid plating 2.0 to 3.0 m nickel body al 2 o 3 ceramic pb free pcb footprint top view a72 ywws
www.rfm.com e-mail: info@rfm.com page 4 of 4 ? 2012 by rf monolithics, inc. SF2315E - 10/29/12 tape and reel specifications ?b? quantity per reel inches millimeters 7 178 500 13 330 3000 see detail "a" 1 3 . 0 2 0 . 2 2.0 12.0 1 0 0 r e f . " b " r e f . component orientation and dimensions carrier tape dimensions ao 3.35 mm bo 3.35 mm ko 1.40 mm pitch 8.0 mm w 12.0 mm ro.3 (max.) ko section a-a 0.3 0.05 section b-b bo 2.0 4.0 ao pitch b b a r0.5 (max.) a 5 . 5 1 2 . 0 1 . 7 5 1.5 1.50 pin #1 user direction of feed
|
