View MIC5393-FMYMX-TR_8849044.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mic5392/3 high - performance dual 150ma ldo general description the mic5392/3 is a tiny dual low - dropout linear regulator ideally suited for portable electronics. it is ideal for general purpose/digital applications which require high - power supply ripple rejection (psrr) >60db, eliminating the need for a bypass capacit or and providing two enable pins for maximum flexibility. the mic5392/3 integrates two high - performance; 150ma ldos into a tiny 6 - pin, 1.2mm 1.2mm leadless dfn package, which provides exceptional thermal package characteristics. the mic5392/3 is a cap d esign which enables operation with very small ceramic output capacitors for stability, thereby reducing required board space and component cost. the combination of low - drop - out voltage, high power supply rejection and exceptional thermal package characteri stics makes it ideal for powering mobile phones camera modules, image sensors, pdas, mp3 players and audio codec power applications. the mic5392/3 is available in fixed - output voltages in the tiny 6 - pin 1.2mm 1.2mm leadless dfn package which is only 1.44 mm 2 in area. additional voltage options are available. datasheets and support documentation are available on micrels web site at : www.micrel.com . features ? 2.5v to 5.5v input voltage range ? two 150ma output current ld os ? high output accuracy ? 2% initial accuracy ? low quiescent current (32a per ldo) ? stable with 1f ceramic output capacitors ? independent enable pins ? low dropout voltage (155mv at 150ma) ? thermal - shutdown protection ? current - limit protection ? internal 25? outpu t discharge circuit (mic5393) ? 1.2mm 1. 2mm extra thin dfn package (h 0 .4mm) ? 1.2mm 1.2mm thin dfn package applications ? smart phones ? tablet pcs ? gps, pmp, pdas, and handhelds ? audio codec power ? portable electronics ? 5v systems typical application camera dsp power supply circuit micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com december 18 , 2014 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 ordering information part number ( 1 ) manufacturing part number marking code voltage junction temperature range package ( 2 ) mic5392 - 1.2/1.0ymt mic5392- 4cymt rj 1.2/1.0v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5392-1.5/2.8ymx ( 4 ) mic5392- fmymx rx 1.5/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5392 - 2.8/1.5ymt mic5392- mfymt rp 2.8/1.5v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5392 - 2.8/1.8ymt mic5392- mgymt rd 2.8/1.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5392-3.0/1.8ymx ( 4 ) mic5392- pgymx 1r 3.0/1.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5392 - 3.0/2.8ymt mic5392- pmymt rm 3.0/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5392-3.0/2.8ymx ( 4 ) mic5392- pmymx 2r 3.0/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5392-3.0/3.0ymx ( 4 ) mic5392- ppymx 3r 3.0/3.0v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5392-3.3/1.8ymx ( 4 ) mic5392- sgymx 4r 3.3/1.8v C 40 c to +125 c 6- pin 1.2 mm 1.2mm extra thin dfn mic5392 - 3.3/3.3ymt mic5392- ssymt rl 3.3/3.3v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5392-3.3/3.3ymx ( 4 ) mic5392- ssymx 5r 3.3/3.3v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-1.5/2.8ymx ( 3 ) mic5393- fmymx u6 1.5/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-2.8/2.8ymx ( 3 ) mic5393- mmymx uv 2.8/2.8 C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-3.0/1.8ymx ( 3 ) mic5393- pgymx u5 3.0/1.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-3.0/2.8ymx ( 3 )( 4 ) mic5393- pmymx uu 3.0/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-3.0/3.0ymt ( 3 ) mic5393- ppymt ul 3.0/3.0v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5393-3.0/3.0ymx ( 3 ) mic5393- ppymx u3 3.0/3.0v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-3.3/1.8ymt ( 3 ) mic5393- sgymt ub 3.3/1.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5393-3.3/1.8ymx ( 3 ) mic5393- sgymx u2 3.3/1.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic5393-3.3/3.3ymt ( 3 ) mic5393- ssymt ur 3.3/3.3v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5393-3.3/3.3ymx ( 3 ) mic5393- ssymx u4 3.3/3.3v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn mic539 3- 1.5/2.8ym t mic5393- fmymt up 1.5/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5393 - 1.8/2.8ymt mic5393- gmymt ut 1.8/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm thin dfn mic5393 - 1. 8/2.8ymx mic5393- gmymx u7 1.8/2.8v C 40 c to +125 c 6- pin 1.2mm 1.2mm extra thin dfn notes: 1. other voltages available. contact micrel for details. 2. thin dfn and extra thin dfn are green, rohs -compliant package. lead finish is nipdau. mold compound is halogen free. 3. mic5393 offers auto -discharge function. 4. contact factory for availability. december 18 , 2014 2 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 pin configuration 6- pin 1.2mm 1.2mm thin dfn (mt) 6- pin 1.2mm 1.2mm extra thin dfn (mx) (top view) pin description pin number pin name pin function 1 vout1 output regulator 1. connect a capacitor to ground. 2 vout2 output regulator 2. connect a capacitor to ground. 3 gnd ground . 4 en2 enable input for regulator 2 . logic high enables operation of regulator 2. logic low will shut down regulator 2. do not leave floating . 5 vin input voltage supply. connect a capacitor to ground. 6 en1 enable input for regulator 1. logic high enables operation of regulator 1. logic low will shut down regulator 1. do not leave floating . ep epad exposed heat sink pad. connect to ground. december 18 , 2014 3 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 absolute maximum ratings ( 5 ) supply voltage (v in ) ........................................ C 0.3v to +6v enable voltage (v en1 , v en2 ). ............................ C 0.3v to vin power dissipation (p d ) ........................... internally limited ( 7 ) lead temperature (soldering, 10sec.) ....................... 260c junction temperature (t j ) ........................ C 40c to +125c storage temperature (t s ) ......................... C 65c to +150c esd rating ( 8 ) ................................................... ............... 2 kv operating ratings ( 6 ) supply voltage (v in ) ..................................... +2.5 v to + 5.5 v enable voltage (v en1 , v en2 ) .............................. C 0.3v to v in junction temperature (t j ) .......................... C 40c to +85c junction thermal resistance 1.2mm 1.2mm thin dfn - 6 ( ja ) ..................... 173 c/w 1.2mm 1.2mm extra thin dfn - 6 ( ja ) ........... 173 c/w electrical characteristics ( 9 ) v in = v en1 = v en2 = v out + 1v; higher of the two regulator outputs; i outldo1 = i outldo2 = 100a; c out1 = c out2 = 1f; t j = 25c, bold values indicate C 40c to +125c, unless noted. paramete r condition min. typ . max . units output voltage accuracy variation from nominal v out C 2.0 +2.0 % variation from nominal v out ; C 40c to +125c C 3.0 +3.0 line regulation v in = v out +1v to 5.5v 0.02 0.3 %/v load regulation i out = 100a to 150ma 0.3 1 % dropout voltage i out = 50ma i out = 150ma 50 155 110 310 mv ground pin current v en 1 = high; v en 2 = low; i out = 0ma v en 1 = low; v en 2 = high; i out = 0ma v en 1 = v en 2 = high; i out 1 = i out 2 = 0ma 32 32 57 45 45 85 a ground pin current in shutdown v en 1 = v en 2 = 0v 0.05 1 a ripple rejection f = 1khz; c out = 1 f 60 db current limit v out = 0v 200 325 550 ma output voltage noise c out = 1 f, 10hz to 100khz 100 v rms auto - discharge nfet resistance mic5393 only; v en 1 = v en 2 = 0v; v in = 3.6v 25 enable input s (en1/en2) enable input voltage logic low 0.2 v logic high 1.2 enable input current v il 0.2 v 0.01 1 a v ih 1.2 v 0 .01 1 turn -o n time c out = 1 f 50 125 s notes: 5. exceeding the absolute maximum rating may damage the device. 6. the device is not guaranteed to function outside its operating rating. 7. the maximum allowable power dissipation of any t a (ambient temperature) is p d(max) = (t j (max) C t a ) / ja . exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. 8. devices are esd sensitive. handling precautions recommended. human body model, 1.5k in series with 100pf. 9. specification for packaged product only. december 18 , 2014 4 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 typical characteristics december 18 , 2014 5 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 typical characteristics (continued) december 18 , 2014 6 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 functional characteristics december 18 , 2014 7 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 functional diagram figure 1. simplified mic5392 functional block diagram figure 2 . simplified mic5393 functional block diagram december 18 , 2014 8 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 application informa tion mic5392/3 is a dual 150ma ldo in a small 1.2mm 1.2mm package. the mic5393 includes an auto - discharge circuit for each of the ldo outputs that are activated when the output is disabled. the mic5392/3 regulator is fully protected from damage due to fault conditions through linear current limiting and th ermal shutdown. input capacitor the mic5392/3 is a high - performance, high - bandwidth device. an input capacitor of 1f capacitor is required from the input to ground to provide stability. low - esr ceramic capacitors provide optimal performance at a minimum o f space. additional high - frequency capacitors, such as small - valued npo dielectric - type capacitors, help filter out high - frequency noise and are good practice in any rf - based circuit. x5r or x7r dielectrics are recommended for the input capacitor. y5v diel ectrics lose most of their capacitance over temperature and are therefore, not recommended. output capacitor the mic5392/3 requires an output capacitor of 1f or greater to maintain stability. the design is optimized for use with low - esr ceramic chip capac itors. high - esr capacitors may cause high frequency oscillation. the output capacitor can be increased, but performance has been optimized for a 1f ceramic output capacitor and does not improve significantly with larger capacitance. x7r/x5r dielectric - ty pe ceramic capacitors are recommended because of their temperature performance. x7r - type capacitors change capacitance by 15% over their operating temperature range and are the most stable type of ceramic capacitors. z5u and y5v dielectric capacitors chang e value by as much as 50% and 60%, respectively, over their operating temperature ranges. to use a ceramic chip capacitor with y5v dielectric, the value must be much higher than an x7r ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range. no - load stability unlike many other voltage regulators, the mic5392/3 will remain stable and in regulation with no load. this is especially important in cmos ram to keep applications alive. enable/shutdown the mic5392/3 c omes with two active - high enable pins that allow each regulator to be disabled independently. forcing the enable pin low disables the regulator and sends it into a zero off - mode - current state. in this state, current consumed by the regulator goes nearly to zero. when disabled the mic5393 switches a 25 (typical) load on the regulator output to discharge the external capacitor. forcing the enable pin high enables the output voltage. the active - high enable pin uses cmos technology and the enable pin cannot be left floating; a floating enable pin may cause an indeterminate state on the output. thermal considerations the mic5392/3 is designed to provide 150ma of continuous current for both outputs in a very small package. maximum ambient operating temperature can be calculated based on the output current and the voltage drop across the part. for example if the input voltage is 3.6v, the output voltage is 3.0v for vout1, 2.8v for vout2 and the output current = 150ma. the actual power dissipation of the regulator circuit can be determined using equation 1 : eq. 1 p d = (v in C v out1 ) i out1 + (v in C v out2 ) i out2 + v in i gnd because this device is cmos and the ground current is typically <100a over the load range, the power dissipation contributed by the ground current is <1% and can be ignored for the calculation in equation 2 : eq. 2 p d = (3.6v C 3.0v) 150ma + (3.6v - 2.8) 150ma p d = 0.21w to determine the maximum ambient operating temperature of the package, use the junction - to - ambient thermal resistance of the device and the following basic formula in equation 3 : eq. 3 ? ?? ? ? ?? ? ? = ja a j(max) d(max) t t p t j(max) = 125c, and the maximum junction temperature of the die, ja , thermal resistance = 173c/w. substituting pd for pd(max) and solving for the ambient operating temperature will give the maximum operating conditions for the regulator circuit. the junction - to - ambient thermal resistance for the minimum footprint is 173c/w. the maximum power dissipation must not be exceeded for proper operation. december 18 , 2014 9 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 for example, when operating the mic5392 - pmymt at an input voltage of 3.6v and 150ma loads at each output with a minimum footprint layout, the maximum ambient operating temperature ta can be determined in eq uation 4 : eq. 4 0.21w = (125c C ta)/(173c/w) ta = 89c therefore, a 2.8v/1.8v application with 150ma at each output current can accept an ambient operating temperature of 58c in a 1.2mm 1.2mm dfn package. for a full discussion of heat sinking and thermal effects on voltage regulators, refer to the regulator thermals section of micrels designing with low - dropout voltage regulators handbook. this information can be found on micrel's web site at: http://www.micrel.com/_pdf/other/ldobk_ds.pdf december 18 , 2014 10 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 typical application circuit bill of materials item part number manufacturer description qty. c1, c2, c3 grm188r61a105ke19d murata ( 10 ) capacitor, 1 f , 10 v, x5r, 0603 3 u1 mic 5392/3 -xxymt mic5392/3 -xxymx micrel, inc. ( 9 ) high - performance dual 150ma ldo 1 notes: 10. murata: www.murata.com . 11. micrel, inc.: www.micrel.com . december 18 , 2014 11 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 pcb layout recommendations top layer bottom layer december 18 , 2014 12 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 package information and recommended landing pattern ( 12 ) 6-pin 1mm 1mm thin dfn (mt) note: 12. package information is correct as of the publication date. for updates and most current information, go to www.micrel.com . december 18 , 2014 13 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 package information and recommended landing pattern ( 12 ) (continued) 6- pin 1.2mm 1.2mm extra thin dfn (mx) december 18 , 2014 14 revision 1.3 downloaded from: http:///
micrel, inc. mic5392/3 micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944 - 0800 fax +1 (408) 474 - 1000 web http://www.micrel.com micrel, inc. is a leading global manufacturer of ic solutions for the worldwide high pe rformance linear and power, lan , and timing & communications markets. the companys products include advanced mixed - signal, analog & power semiconductors; high - performance communication, clock management, mems - based clock oscillators & crystal - less clock generators, ethernet switch es, a nd physical layer transceiver ics. company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and com p uter products. corporation headquarters and state -of-the- art wafer fabrication facili ties are located in san jose, ca, with regional sales and support offices and advanced technology design centers situated throughout the americas, europe , and asia. additionally , the company maintains an extensive network of distributors and reps worldwid e. micrel makes no representations or warranties with respect to the accuracy or completeness of the inf ormation furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for its use. micrel res erves the right to change circuitry, specifications and descriptions at any time without notice. no license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in micrels terms and conditions of sale for such products, micrel assumes no liability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel produc ts including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where mal functio n of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or sys tems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. a purchasers use or sale of micrel products for use in life support appliances, devices or systems is a purchasers own risk and purchaser agrees to fully indemnify micrel for any damages resu lting from such use or sale. ? 2012 micrel, incorporated. december 18 , 2014 15 revision 1.3 downloaded from: http:///

▲Up To Search▲

Price & Availability of MIC5393-FMYMX-TR

	To Download MIC5393-FMYMX-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .