80 a power relay features ? 80 amp switching ? wide contact gap > 2.05mm ? holding power <100 mw ? dielectric strength 5000 vrms ? isolation spacing greater than 10 mm ? double insulation, en 60730-1 (vde 0631, part 1) ? reinforced insulation, en 60335-1 (vde 0700, part 1) ? ul, cur e44211 ? vde certificate 40044305 - a zettler company zettler electronics gmbh junkersstr. 3, d-82178 puchheim, germany phone: +49 89 800 97-0 fax: +49 89 800 97-200 office@zettlerelectronics.com www.zettlerelectronics.com this product specification to be used only together with the application notes which can be downloaded from http://www.zettlerelectronics.com/pdfs/relais/applicationnotes.pdf group g r o u p 2016-06-27 general data life expectancy minimum operations mechanical 1 x 10 5 electrical 3 x 10 4 at 30 a 250 vac res. operate time (typical) 40 ms at nominal coil voltage release time (typical) 5 ms at nominal coil voltage (with no coil suppression) dielectric strength 5000 vrms coil to contact (at sea level for 1 min.) 2500 vrms between open contacts insulation 1000 megohms min. at 20c resistance 500 vdc 50% rh insulation c250 (according to overvoltage category: iii din vde 0110, pollution degree: 3 iec 60664-1) nominal voltage: 250 vac dropout greater than 5% of nominal coil voltage ambient temperature at nominal coil voltage operating -40c (-40f) to 85c (185f) vibration 0.062" (1.5 mm) da at 10?55 hz shock 10 g enclosure pa terminals tinned copper alloy, p. c. max. solder temp. 270c (518f) max. solder time 5 seconds weight 105 grams packing unit in pcs 10 per inner carton / 100 per carton box notes 1. all values at 20c (68f). 2. relay may pull in with less than ?must operate? value. 3. specifications subject to change without notice. 4. recommended pcb cross section 16 mm2. rohs compliant ! AZSR180 arrangement spst (1 form a) ratings resistive load: max. switched power: 2400 w or 22160 va max. switched current: 80 a (1000 cycles) max. continuous current: 80 a max. switched voltage: 150 vdc* or 440 vac * note: if switching voltage is greater than 30 vdc, special precautions must be taken. please contact the factory. rated load ul vde 80 a at 277 vac, resistive, 1k cycles 80 a at 277 vac, resistive, 1k cycles, 85c 30 a at 263 vac, ac-7a, 30k cycles , 85c material silver tin oxide resistance < 50 milliohms initially contacts power at pickup voltage (typical) max. continuous dissipation temperature rise 270 mw 2.0 w at 20c (68f) ambient 15c (27f) at nominal coil voltage temperature max. 155c (311f) class f coil
- a zettler company zettler electronics gmbh junkersstr. 3, d-82178 puchheim, germany phone: +49 89 800 97-0 fax: +49 89 800 97-200 office@zettlerelectronics.com www.zettlerelectronics.com this product specification to be used only together with the application notes which can be downloaded from http://www.zettlerelectronics.com/pdfs/relais/applicationnotes.pdf group g r o u p 2016-06-27 AZSR180 coil specifications - spst (1 form a) nominal coil vdc must operate vdc min. holding vdc max. continuous vdc coil resistance ohm 10% order number 12 9.00 4.0 24.0 300 AZSR180-1ae-12d 24 18.00 8.0 48.0 1200 AZSR180-1ae-24d 5 3.75 1.7 10.0 50 AZSR180-1ae-5d 9 6.75 3.1 18.0 170 AZSR180-1ae-9d 12 9.00 4.0 24.0 300 AZSR180-1ae-12d 18 13.50 6.5 36.0 675 AZSR180-1ae-18d 24 18.00 8.0 48.0 1200 AZSR180-1ae-24d relay ordering data pc board layout wiring diagram 5 1 2 3 4 6 viewed toward terminals viewed toward terminals 10.0 7.0 x 2.5 (4x) 14.7 3.5 22.8 3.3 x 1.3 (2x) viewed toward terminals 6,5 x 2 (4x) 2,8 x 0,8 (2x) 10.0 3.5 22.8 14.7 8.2 49.2 25.0 40.0 2.0 4.5 mechanical data dimensions in mm. tolerance: .25 mm it is absolute necessary to provide a connection between pin 3 and 4 (5 and 6) on the pcb to avoid a malfunction of the relay! check also note 4 on first page, please.
|
