ilpa40jud series 40w dimmable water - proof constant current led driver C wide input voltage 90 to 305vac, 47 to 63hz C constant output current available from 350ma to 3330ma C over voltage, short circuit, over load protection C high efficiency (up to 88%) C active power factor correction (pfc) (92% typical) C ip66 waterproof rating C comply with ul8750 & en61347 safety regulation (pending) 2 year warranty approvals: (pending) single output part number output current range (min. / typ. / max.) output voltage (min. / max.) efficiency (220vac, full load) over voltage protection (min. / typ. / max.) max. output power ilpa40jud - s333ds 3164 / 3330 / 3497 ma 4 / 12 vdc 84% 13 / 15 / 17 vdc 35w ilpa40jud - s222ds 2109 / 2220 / 2331 ma 6 / 18 vdc 85% 22 / 24 / 26 vdc 36w ilpa40jud - s166ds 1577 / 1660 / 1743 ma 8 / 24 vdc 86% 30 / 32 / 34 vdc 38w ilpa40jud - s140ds 1330 / 1400 / 1470 ma 10 / 29 vdc 87% 36 / 38 / 40 vdc 36w ilpa40jud - s128ds 1216 / 1280 / 1344 ma 11 / 31 vdc 87% 41 / 43 / 45 vdc 38w ilpa40jud - s105ds 998 / 1050 / 1103 ma 12 / 36 vdc 87% 46 / 48 / 50 vdc 38w ilpa40jud - s070ds 665 / 700 / 735 ma 18 / 54 vdc 87% 68 / 70 / 72 vdc 38w ilpa40jud - s045ds 428 / 450 / 473 ma 30 / 89 vdc 88% 114 / 116 / 118 vdc 40w ilpa40jud - s035ds 333 / 350 / 368 ma 38 / 114 vdc 88% 146 / 148 / 150 vdc 40w electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 305 vac input frequency 47 63 hz output power range vin=90 to 305vac 0 40 w input current (low line) io=full load, vin=115vac 0.48 a input current (high line) io=full load, vin=230vac 0.23 a high line inrush current io=full load, 25c, cool start, vin=230vac 20 a power factor correction vin=110vac 99 % efficiency io=full load, vin=220vac 88 % no load power dissipation 3 w line regulation io=full load 2 % load regulation vin=230vac 5 % over voltage protection latch mode. the power unit shall return to normal operation only after the power is turn - on again. (please refer to output table.) over load protection hiccup mode. the power supply shall be self - recovery when the fault condition is removed. 1.25 po short circuit protection no damage shall occur when any output operating in a short circuit condition. the power supply shall be self - recovery when the fault condition is removed. output overshoot / undershoot when power on or off 10 % start up time io=full load, vin=100vac 1.7 2 s ripple & noise (peak to peak) measured by 20 mhz bandwidth oscilloscope and the output paralleled a 0.1 uf ceramic capacitor and a 10 uf electrolytic capacitor. 5 % vo
conditions parameter test conditions min. typ. max. unit operating temperature humidity: 10% rh to 100% rh - 20 70 c storage temperature humidity: 5% rh to 100% rh - 40 85 c mtbf: operation temperature at 25c, calculated per mil - hdbk - 217f 0.487m hours life time at 25c ambient temperature 0.077m hours approvals and compliance parameter standards emi en55015 ems en61000 - 3 - 2, en61000 - 3 - 3, en61000 - 4 - 2, en61000 - 4 - 3, , en61000 - 4 - 4, , en61000 - 4 - 5, en61000 - 4 - 6, en61000 - 4 - 8, en61000 - 4 - 11, en61547 safety ul/c - ul, ce (pending) ul8750 compliant to ul1310 clast 2, ul1012, ul935, csa - c22.2 no. 0, csa - c22.2 no. 107.1, csa - c 22.2 no.250.0, en61347 - 1,en61347 - 2 - 13 waterproof ip66 rating mechanical parameter specification dimension, 78x80x25mm (3.07x3.15x0.98 inches) net weight 200g approx. dimming control parameter min. typ. max. unit 10v output voltage 9.8 10v 10.2 vdc 10v output source current - 10 - 2 ma absolute max. voltage on the 1~10v input pin - 2 - 15 vdc source current on 0 - 10v input pin 0 - 1 ma the dimmer control may be operated from either a potentiometer or from an input signal of 0 ~ 10 vdc. two recommended implementations are provided above notes: 1. for the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of t he max. output voltage for any given model). 2. if the output voltage is maintained above 50% of the maximum output voltage, the dimmer control may be operated over the entire 0 - 10v range with output current varying from 100% down to practically 0%. 3. if the output voltage is maintained between 33 - 50% of the maximum output voltag e, the dimmer control may be operated over 5 - 10v range with output current
|
