spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 3.2x2.4mm smd chip led lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: APBD3224LSURKZGKC hyper red green features z 3.2x2.4mm smd led, 2.4mm thickness. z low power consumption. z ideal for backlight and indicator. z package : 1500pcs / reel. z moisture sensitivity level : level 3. z low current if=2ma operating. z rohs compliant. descriptions z the hyper red source color devices are made with algainp on gaas s ubstrate light emitting diode. z the green source color devices are made with ingan on sapphire light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1(0.004") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications.
spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 2. luminous intensity/ luminous flux: +/-15%. *lumin ous intensity with asterisk is measured at 20ma. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4. excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradatio n or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (mcd) [2] @ 2ma v iewing angle [1] min. typ. 2 1/2 APBD3224LSURKZGKC hyper red (algainp) water clear 20 50 20 *10 *30 120 250 *120 *250 green (ingan) symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper red green 645 515 nm i f =2ma d [1] dominant wavelength hyper red green 630 525 nm i f =2ma ? 1/2 spectral line half-width hyper red green 28 35 nm i f =2ma c capacitance hyper red green 35 45 pf v f =0v;f=1mhz v f [2] forward voltage hyper red green 1.75 2.65 2.1 3.0 v i f =2ma i r reverse current hyper red green 10 50 ua v r = 5v min. 1.5 2.2 parameter hyper red green units power dissipation 63 75 mw dc forward current 30 25 ma peak forward current [1] 185 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c electrostatic dischar ge threshold (hbm) 3000 450 v
spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 APBD3224LSURKZGKC hyper red
spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 green
spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 APBD3224LSURKZGKC reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao4551 rev no: v.1a date: aug/01/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015159 packing & label specifications APBD3224LSURKZGKC terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
