kmp_1605c_b05 page 1 of 2 for full details go to www.murata-ps.com/rohs selection guide order code turns ratio min. primary inductance max. dc resistance min. et constant max. leakage inductance max. inerwinding capacitance h ? vs h pf 1605c 1:1 26.0 0.2 1.8 0.2 8 absolute maximum ratings operating free air temperature range 0c to 70c storage temperature range -60c to 125c isolation voltage (fash tested for 1 second) 500vrms soldering information 1 peak wave solder temperature, 1.5mm from case 300?c for 10 seconds pin fnish matte tin all specifcations typical at t a =25 c. 1 for further information, please visit www.murata-ps.com/rohs technical notes isolation voltage hi pot test, flash tested, withstand voltage, proof volt - age, dielectric withstand voltage & isolation test voltage are all terms that relate to the same thing, a test voltage, applied for a specifed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. all products in this series are 100% production tested at their stated isolation voltage. a question commonly asked is, what is the continuous voltage that can be applied across the part in normal opera - tion? for a part holding no specifc agency approvals both input and output should normally be maintained within selv limits i.e. less than 42.4v peak, or 60vdc. the isolation test volt - age represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. the part could be expected to function cor - rectly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-acces - sible circuitry according to safety standard requirements. repeated high-voltage isolation testing it is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environ - ment. this series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. while parts can be expected to withstand several times the stated test voltage, the isolation capability does de - pend on the wire insulation. any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. we there - fore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specifed test voltage. this consideration equally applies to agency recog - nized parts rated for better than functional isolation where the wire enamel insulation is always supple - mented by a further insulation system of physical spacing or barriers. features n rohs compliant n 500vrms isolation n industry-standard footprint n compatible with standard networks n backward compatible with sn/pb soldering systems description the 1605c is a package of unity-turns-ratio isolation transformers. the transformers are designed to have fast rise times with low phase shift and insertion loss to reduce signal distortion. the high shunt impedance of these devices minimises system loading and enables the correct termination conditions to be accurately defned by means of resistors. the devices can be used as network-node isolators in csma/cd systems. 1605c lan-pak for csma/cd systems www.murata-ps.com www.murata-ps.com/ support
kmp_1605c_b05 page 2 of 2 murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. specifcations are subject to change without notice. ? 2011 murata power solutions, inc. package specifications mechanical dimensions pin connections tube dimensions 0.260.05 (0.010.002) 22.50 (0.886) 6.86 (0.270) 5.80 (0.228) 4.50 (0.177) 2.54 (0.10) 17.78 (0.7) 8.85 (0.348) 0.500.05 (0.020.002) 0.640.15 (0.0250.006) 1600c xyyww 0.250.05 (0.0010.002) 0.260.05 (0.010.002) 22.50 (0.886) 6.86 (0.270) 5.0 max. (0.197) 4.50 (0.177) 2.54 (0.10) 17.78 (0.7) 8.85 (0.348) 0.500.05 (0.020.002) 0.640.15 (0.0250.00008) 1605c xyyww all dimensions in mm (inches) 0.25 (0.001) unless otherwise stated. package weight: 1.7g typ. 16 1 2 3 4 5 6 7 8 15 14 13 12 11 10 9 0.250.05 (0.0010.002) 0.250.05 (0.0010.002) 22.50 (0.886) 6.86 (0.270) 5.0 max. (0.197) 4.50 (0.177) 2.54 (0.10) 17.78 (0.7) 8.65 (0.34) 0.500.05 (0.020.002) 0.640.15 (0.0250.00008) 1605c xyyww pin connections 5.4 (0.213) 13.2 (0.520) 0.5 (0.020) 4.8 (0.189) 14.4 (0.567) 9.6 (0.374) tube length: 520mm (20.5) all dimensions in mm (inches) 0.25 (0.001) unless otherwise stated. package quantity: 20 1605c lan-pak for csma/cd systems murata power solutions, inc. 11 cabot boulevard, mansfeld, ma 0204 8 -1151 u.s.a. iso 9001 and 14001 registered www.murata-ps.com/ support
|
