wall industries, inc. 5 watson brook road exeter, nh 03833 01/08/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 1 of 5 datasheet rev. d psge50 series 88~264vac (125~373vdc) input single outputs up to 52.8 watts output power ac/dc switching power supplies features ? single output ? rohs compliant ? universal ac input / full range ? high efficiency, long life, and high reliability ? 10% output voltage adjustability ? green design, no-load power consumption < 0.5w ? energy star compliant ? cooling by free air convection ? power on with led indicator ? all using 105c long life electrolytic capacitors ? high operating temperature: -25c to +70c ? 100% full load burn-in tested ? withstand 5g vibration test ? brown-out (low ac input voltage) protection ? over voltage, over load, and short circuit protection description the psge50 series of ac/dc switching power supplies offers up to 52.8 watts of output power in a 3.90? x 3.21? x 1.40? enclosed case. this series has a universal input voltage ra nge of 88~264vac (125~373vdc) and single outputs of 3.3, 5, 12, 15, 24, and 48vdc. some features include high effici ency up to 90%, 10% output adjustability, no-load power consumption < 0.5w, and a high operating te mperature range of -25c to +70c. this series also has over voltage, short circuit, over load, and brown-out (low ac input voltage) protecti on. all models have been 100% full load burn-in tested and are rohs and energy star compliant. this series also has ul 60950-1, tuv en60950-1, and ce safety approvals.
rev. d psge50 series single output up to 52.8 watts ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter, nh 03833 01/08/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 2 of 5 specifications: psge50 series all specifications are based on 25c, nominal input volt age, and maximum output current unless otherwise noted. we reserve the right to change specifi cations based on technological advances. input specifications input voltage range 88 ~ 264vac 125 ~ 373vdc (withstand 300vac surge for 5 seconds without damage) input frequency 50hz / 60hz ac current 1.3a typ. at 115vac; 0.5a typ. at 230vac inrush current cold start 40a typ. at 230vac output specifications output voltage see table output power see table output voltage adjustability 10% voltage tolerance (see note 2) 3.3 vdc output model: 3% 5 vdc output model: 2% 12~48 vdc output models: 1% load regulation (see note 3) see table line regulation 0.5% (measured from low line to high line at full load) output current see table ripple & noise (see note 1) see table setup, rise time (see note 5) 1000ms, 80ms at 115vac and full load 800ms, 80ms at 230vac and full load hold-up time >10ms at 115vac and full load; >32ms at 230vac and full load temperature coefficient 0.03% / c (0~50c) protection short circuit protection yes over voltage protection 115% ~ 150% rated output voltage protection type: latch-off mode over load protection >110% rated output power protection type: hiccup mode; recover automatically after fault condition is removed brown-out protection (low ac input voltage) yes general specifications efficiency see table input to output 3000vac (4242vdc) for 1 minute input to fg 1500vac (2121vdc) for 1 minute withstand voltage output to fg 500vac (707vdc) for 1 minute isolation resistance 100m ? at 500vdc (input to output, input to fg, output to fg) leakage current < 2ma at 240vac environmental specifications working temperature -25c to +70c (see derating curve) storage temperature -40c to +85c working humidity 20% to 90% rh (non-condensing) storage humidity 10% to 95% rh vibration 10 ~ 500hz, 5g 10min/1cycle, period fo r 60 minutes each along x,y,z axes. cooling free air convection mtbf 420,400 hours (compliance: mil-hdbk-217f) physical specifications weight, packing 9.88oz (280g); 45pcs/14kg dimensions (l x w x h) 3.90 x 3.21 x 1.40 inches (99.0 x 81.5 x 35.5 mm) safety & emc (see note 6) safety standards ul60950-1, 2 nd edition, tuv en60950-1: 2006+a11 approved emi conduction & radiation en55022: 1998+a1: 2000+a2: 2003 class b harmonic current en61000-3-2: 2000 class a, en61000-3-3: 1995+a1: 2001 ems immunity en61204-3: 2000, en55024: 1998+a1: 2001+a2: 2003 light industry level, criteria a
rev. d psge50 series single output up to 52.8 watts ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter, nh 03833 01/08/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 3 of 5 model selection table model number input voltage range output voltage output current load (3) regulation output (1) ripple & noise output power efficiency (4) psge-50-3.3 3.3 vdc 10a 2.0% 100mvp-p 33w 78% psge-50-5 5 vdc 10a 1.0% 100mvp-p 50w 83% PSGE-50-12 12 vdc 4.2a 0.5% 120mvp-p 50.4w 88% psge-50-15 15 vdc 3.4a 0.5% 120mvp-p 51w 89% psge-50-24 24 vdc 2.2a 0.5% 120mvp-p 52.8w 90% psge-50-48 88 ~264 vac (125~373 vdc) 48 vdc 1.1a 0.5% 200mvp-p 52.8w 90% notes 1. ripple & noise is measured at 20mhz bandwidth by using a 12" twisted pair-wire terminated with a 0.1f capacitor and a 47f capacitor in parallel. 2. tolerance includes set up tolerance, line regulation, and load regulation. 3. load regulation is measured from 0% to 100% full load. 4. typical value at 230vac input voltage. 5. the length of the setup time is measured at first cold st art; turning the power supply on and off very quickly may lead to an increase in the setup time. 6. the power supply is considered a component which will be in stalled into final equipment. the final equipment must be re-confirmed that it still meets emc directives. derating curves 90 ta=25c 100 110 120 264 40 50 60 70 80 load (%) input voltage (vac) 90 100 -25 ambient temperature (c) 0 10203040506070 20 40 60 80 100 load (%) load vs temperature load vs input voltage
rev. d psge50 series single output up to 52.8 watts ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter, nh 03833 01/08/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 4 of 5 mechanical drawings top of case bottom of case tolerance: 0.02? (0.5mm) tolerance: 0.02? (0.5mm) 0.47 (12.00) unit: inches (mm) unit: inches (mm) ?0.14 (?3.50) 0.22 (5.50) ?0.14 (?3.50) 2 - ?0.14 (?3.50) 6-m3 3.21 (81.50) 3.43 (87.00) 0.38 (9.60) 0.20 (5.00) 0.19 (4.88) 0.35 (9.00) 1.34 (34.00) 0.02 (0.50) 0.28 (7.00) 0.30 (7.70) 1.40 (35.50) 0.33 (8.40) 0.12 (3.00) 0.12 (3.00) 0.15 (3.70) 0.57 (14.60) 0.55 (13.85) 0.90 (22.75) 1.10 (28.00) 3.21 (81.50) 0.14 (3.50) 1.59 (40.50) 1.44 (36.50) 0.22 (5.50) 0.20 (5.00) 0.39 (10.00) 2.17 (55.00) 3.90 (99.00) 0.20 (5.00) 0.20 (5.00) 1.93 (49.00) 0.45 (11.50) 0.39 (10.00) 0.20 (5.00) 0.20 (5.00) 0.45 (11.50) 0.43 (11.00) 0.24 (6.00) 0.24 (6.00) 0.06 (1.6) 0.35 (8.88) 1.40 (35.50) 0.91 (23.10) 0.06 (1.50) 0.33 (8.40) 3.21 (81.49) 2.60 (66.00) 0.40 (10.21) 0.51 (13.00) 0.12 (3.00) 0.94 (23.75) 0.33 (8.50) 1.94 (49.24) 0.29 (7.49) 1.26 (32.00) 1.57 (40.00) 2.48 (63.00) 0.17 (4.40) 0.26 (6.50) 0.28 (7.00) 0.14 (3.50) 0.28 (7.00) 0.24 (6.00) 0.24 (6.00) 0.93 (23.69) 1.57 (39.91) 0.71 (18.00) 0.71 (18.00) 0.77 (19.50) 0.24 (6.00) 0.28 (7.00) 0.12 (3.00) 0.10 (2.60) ?0.26 (?6.50) ?0.13 (?3.20) 1.24 (31.5)
rev. d psge50 series single output up to 52.8 watts ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter, nh 03833 01/08/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 5 of 5 mechanical drawing unit: inches (mm) tolerance: 0.02? (0.5mm) 1.59 (40.50) 2-m3 l=4 ?0.14 (?3.50) ?0.14 (?3.50) 0.37 (9.50) 0.33 (8.30) 0.20 (5.00) 3.48 (88.50) 3.90 (99.00) 0.20 (5.00) 1.57 (40.00) 3.21 (81.50) l n -v +v ?0.14 (?3.50) ?0.14 (?3.50) 2-m3 0.26 (6.50) 3.44 (87.25) 0.71 (18.00) 1.12 (28.50) 1.40 (35.50) 2.17 (55.00) 0.84 (21.25) 2.91 (74.00) 0.71 (18.00) company information wall industries, inc. has created custom and modified units for over 50 years. our in-house research and development engineers will provide a solution that exceeds your perfo rmance requirements on-time and on budget. our iso9001-2008 certification is just one example of our commitment to produc ing a high quality, well-documented product for our customers. our past projects demonstrate our commitment to you, our cu stomer. wall industries, inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and f unction requirements. we will continue to provide ongoing support for your project a bove and beyond the design and production phases. give us a call today to discuss your future projects. contact wall industries for further information: phone : ? (603)778-2300 toll free : ? (888)587-9255 fax : ? (603)778-9797 e-mail : sales@wallindustries.com web : www.wallindustries.com address : 5 watson brook rd. exeter, nh 03833
|
