Part Number Hot Search : 
544ES Z1051PI GBI15A SD101C 2E124K RD06HVF SL4002B SBM82314
Product Description
Full Text Search
 

To Download NT256D72S4PA0GR-75B Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 1 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. 184pin one bank registered ddr sdram module based on 32mx4 ddr sdram features ? 184 - pin registered 8 - byte dual in - line memory module ? 32 mx 72 double data rate (ddr) sdram dimm ? performance : pc1600 pc2100 speed sort - 8b - 75b - 7k dimm cas latency 3 3.5 3 unit f ck clock frequency 100 133 133 mhz t ck clock cycle 10 7.5 7.5 ns f dq dq burst frequency 200 266 266 mhz ? intended for 100 mhz and 133 mhz applications ? inputs and outputs are sstl - 2 compatible ? v d d = 2.5volt 0.2, v ddq = 2.5volt 0.2 ? single pulsed ras interface ? sdrams have 4 internal banks for concurrent operation ? module has one physical bank ? differential clock inputs ? data is read or written on both clock edges ? bi - directional data strobe with one clock cycle preamble and one - half clock post - amble ? address and control signals are fully synchronous to positive clock edge ? programmable operation: - dimm cas latency: 3 , 3 .5 - burst type: sequential or interleave - burst length: 2, 4, 8 - operation: burst read and write ? auto refresh (cbr) and self refresh modes ? automatic and controlled precharge commands ? 1 2 /1 1 /2 addressing (row/column/bank) ? 15.625 s max. average periodic refresh interval ? s erial presence detect ? gold contacts ? sdrams in 66 - pin tsop type ii package description nt 256 d 72 s 4p a0g r is a regist ered 184 - pin double data rate (ddr) synchronous dram dual in - line memory module (dimm), organized as a one - bank high - speed memory arra y. the 32 mx 72 module is a single - bank dimm that uses eight een 32 mx 4 ddr sdrams in 400 mil tsop packages. the dimm achieves high - speed data transfer rates of up to 266mhz. the dimm is intended for use in applications operating from 100 mhz to 133 mhz clock speeds with data rates of 200 to 266 mhz. clock enable cke0 controls all devices on the dimm. prior to any access operation, the device cas latency and burst type/ length/operation type must be programmed into the dimm by address inputs a0 - a1 1 and i/o inputs ba0 and ba1 using the mode register set cycle. these dimms are manufactured using raw cards developed for broad industry use as reference designs. the use of these common design files minimizes electrical variation between suppliers . the dimm uses serial presence detects implemented via a serial eeprom using the two - pin iic protocol. the first 128 bytes of serial pd data are programmed and locked during module assembly. the last 128 bytes are available to the customer. all nanya 18 4 ddr sdram dimms provide a high - performance, flexible 8 - byte interface in a 5.25? long space - saving footprint. ordering information part number speed organization leads power component module 143mhz (7ns @ cl = 2.5 ) nt 256 d 72 s 4p a0g r - 7k 133mhz (7.5ns @ cl= 2 ) ddr266a pc 2100 133mhz (7.5ns @ cl= 2.5 ) nt 256 d 72 s 4p a0g r - 75b 100mhz (10ns @ cl = 2 ) ddr266b pc2100 125mhz (8ns @ cl = 2.5 ) nt 256 d 72 s 4p a0g r - 8b 100mhz (10ns @ cl = 2 ) ddr200 pc1600 32mx72 gold 2.5v
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 2 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. pin de scription ck0, ck0 differential clock inputs dq0 - dq63 data input/output cke0 clock enable cb0 - cb7 check bit data input/output ras row address strobe dqs0 - dqs17 bidirectional data strobes cas column address strobe v dd power ( 2.5 v) we write enable v ddq supply voltage for dqs(2.5v) s0 chip selects v ss ground a0 - a9, a11 address inputs nc no connect a10/ap address input/autoprecharge scl serial presenc e detect clock input ba0, ba1 sdram bank address inputs sda serial presence detect data input/output reset reset pin sa0 - 2 serial presence detect address inputs v ref ref. voltage for sstl_2 inputs v ddid v dd identification flag. v ddspd serial eeprom positive power su pply(2.5v) pinout pin front pin front pin front pin back pin back pin back 1 v ref 32 a5 62 v ddq 93 v ss 124 v ss 154 ras 2 dq0 33 dq24 63 we 94 dq4 125 a6 155 dq45 3 v ss 34 v ss 64 dq41 95 dq5 126 dq28 156 v ddq 4 dq1 35 dq25 65 cas 96 v ddq 127 dq29 157 s0 5 dq s0 36 dq s3 66 v ss 97 dq s9 128 v ddq 158 nc 6 dq2 37 a 4 67 dqs5 98 dq6 129 dqs12 159 dqs14 7 v dd 38 v dd 68 dq42 99 dq7 130 a 3 1 60 v ss 8 dq 3 39 dq2 6 69 dq43 100 v ss 131 dq30 161 dq46 9 nc 40 dq27 70 v dd 101 nc 132 v ss 162 dq47 10 reset 41 a 2 71 nc 102 nc 133 dq31 163 nc 11 v ss 42 v ss 72 dq 48 103 nc 134 cb4 164 v ddq 12 dq8 43 a1 73 dq49 104 v ddq 135 cb5 165 dq 52 13 dq9 44 cb0 74 v ss 105 dq1 2 136 v ddq 166 dq53 14 dq s1 45 cb1 75 nc 106 dq1 3 137 ck0 167 nc 15 v ddq 46 v dd 76 nc 107 dqs10 138 ck0 168 v dd 16 nc 47 dq s8 77 v ddq 108 v dd 139 v ss 169 dqs15 17 nc 48 a0 78 dqs6 109 dq1 4 140 dqs17 1 70 dq54 18 v ss 49 cb2 79 dq 50 110 dq1 5 141 a10 171 dq55 19 dq1 0 50 v ss 80 dq 51 111 nc 142 cb6 172 v ddq 20 dq1 1 51 cb3 81 v ss 112 v ddq 143 v ddq 173 nc 21 c ke0 52 ba1 82 v ddid 113 nc 144 cb7 174 dq60 22 v ddq key 83 dq56 114 dq20 key 175 dq61 23 dq1 6 53 dq32 84 dq57 115 nc 145 v ss 176 v ss 24 dq1 7 54 v ddq 85 v dd 116 v ss 146 dq36 177 dqs16 25 dq s2 55 dq33 86 dqs7 117 dq21 147 dq37 178 dq62 26 v ss 56 dqs4 87 dq58 118 a11 148 v dd 179 dq63 27 a9 57 dq34 88 dq59 119 dqs11 149 dqs13 180 v ddq 28 dq 18 58 v ss 89 v ss 120 v dd 150 dq38 181 sa0 29 a7 59 ba0 90 nc 121 dq22 151 dq39 182 sa1 30 v ddq 60 dq35 91 sda 122 a8 152 v ss 183 sa2 31 dq 19 61 dq40 92 scl 123 dq23 153 dq44 184 v ddspd
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 3 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. input/output functional description symbol type polarity function ck0 (sstl) positive edge the positive line of the differential pair of system clock inputs which drives the input to the on - dimm pll. all the ddr sdram address and control inputs are sampled on the rising edge of their associated clocks. ck0 (sstl) negative edge the negative line of the differential pair of system clock inputs which drives the input to the on - dimm pll. cke0 (sstl) active high activates the sdram ck signal when high and deactivates the ck signal when low. by deactivat ing the clocks, cke low initiates the power down mode, or the self refresh mode. s0 (sstl) active low enables the associated sdram command decoder when low and disables the command decoder when high. when the command decoder is disabl ed, new commands are ignored but previous operations continue. ras , cas , we (sstl) active low when sampled at the positive rising edge of the clock, ras , cas , we define the operation to be executed by the sdram. v ref supply reference voltage for sstl - 2 inputs v ddq supply isolated power supply for the ddr sdram output buffers to provide improved noise immunity ba0, ba1 (sstl) - selects which sdram bank is to be active. a0 - a9 , a11 a10/ap (sstl) - during a bank activate command cycle, a0 - a1 1 defines the row address (ra0 - ra1 1 ) when sampled at the rising clock edge. during a read or write command cycle, a0 - a 10 defines the column address ( ca0 - ca 10 ) when sampled at the rising clock edge. in addition to the column address, ap is used to invoke autoprecharge operation at the end of the burst read or write cycle. if ap is high, autoprecharge is selected and ba0/ba1 define the bank to be prechar ged. if ap is low, autoprecharge is disabled. during a precharge command cycle, ap is used in conjunction with ba0/ba1 to control which bank(s) to precharge. if ap is high all 4 banks will be precharged regardless of the state of ba0/ba1. if ap is low, the n ba0/ba1 are used to define which bank to pre - charge. dq0 - dq63 , (sstl) - data and check bit input/output pins operate in the same manner as on conventional drams. dq0 ? dq 63 cb0 ? cb7 (sstl) active high data and check bit input/output pins. check bits are only applicable on the x72 dimm configurations. v dd , v ss supply power and ground for the ddr sdram input buffers and core logic dq s 0 ? dq s17 (sstl) negative and positive edge data strobe for input and output data reset (lvc - mos ) active low sa0 ? sa2 - address inputs. connected to either v dd or v ss on the system board to configure the serial presence detect eeprom address. sda - this bidirectional pin is used to transfer data into or out of the spd eeprom. a resistor must be connected from the sda bus line to v dd to act as a pullup. scl - this signal is used to clock data into and out of the spd eeprom. a resistor may be connected from the scl bus time to v dd to act as a pullup. v ddspd supply serial eeprom positive pow er supply.
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 4 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. functional block diagram ( 1 bank, 32 mx 4 ddr sdrams ) a0 - a12 : sdrams d0 - d17 ba0-ba1 : sdrams d0 - d17 v ss ras : sdrams d0- d17 cke : sdrams d0- d17 cas : sdrams d0- d17 we : sdrams d0- d17 dqs0 dq0 dq1 dq2 dq3 i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 serial pd dm rs0 i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm r e g i s t e r ba0-ba1 a0 - a12 ras cas cke0 we cs0 pck pck ra0-ra12 rba0-rba1 rras rcas rcke0a rwe rs0 s0 : sdrams d0 - d17 reset i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm i/o 0 i/o 1 i/o 3 i/o 2 dqs cs d0 dm notes : 1. dq-to-i/o wiring may be changed within a byte 2. dq/dqs/dm/cke/cs relationships are maintained as shown. 3. dq/dqs resistors are 22 ohms. 4. vddid strap connections (for memory device vdd,vddq): strap out (open): vdd = vddq strap in (vss): vdd 1 vddq. 5. address and control resistors are 22ohms. v ddspd v ddq v dd v ref v ss v ddid d0 - d17 d0 - d17 d0 - d17 d0 - d17 strap : see note4 serial pd a0 a2 a1 scl wp sda sa0 sa2 sa1 * wire per clock loading table/wiring diagrams * ck0, ck0 --------- pll* dq8 dq9 dq10 dq11 dq16 dq17 dq18 dq19 dq24 dq25 dq26 dq27 dq32 dq33 dq34 dq35 dq40 dq41 dq42 dq43 dq48 dq49 dq50 dq51 dq56 dq57 dq58 dq59 cb0 cb1 cb2 cb3 dqs1 dqs2 dqs3 dqs4 dqs5 dqs6 dqs7 dqs8 dm0/dqs9 dq4 dq5 dq6 dq7 dq12 dq13 dq14 dq15 dq20 dq21 dq22 dq23 dq28 dq29 dq30 dq31 dq36 dq37 dq38 dq39 dq44 dq45 dq46 dq47 dq52 dq53 dq54 dq55 dq60 dq61 dq62 dq63 cb4 cb5 cb6 cb7 dm1/dqs10 dm2/dqs11 dm3/dqs12 dm4/dqs13 dm5/dqs14 dm6/dqs15 dm7/dqs16 dm8/dqs17
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 5 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. serial presence detect -- part 1 of 2 32 mx 72 1 bank registered ddr sdram dimm based on 32 mx 4 , 4banks, 4 k refresh, 2.5 v ddr sdrams with sp d spd entry value serial pd data entry (hexadecimal) note byte desc ription ddr266a - 7k ddr266b - 75b ddr200 - 8b ddr266a - 7k ddr266b - 75 ddr200 - 8b 0 number of serial pd bytes written during production 128 80 1 total number of bytes in serial pd device 256 08 2 fundamental memory type sdram ddr 07 3 number of row addresses on assembly 1 2 0c 4 number of column addresses on assembly 11 0b 5 number of dimm bank 1 01 6. data width of assembly x72 4 8 7 data width of assembly (cont?) x72 00 8 voltage int erface level of this assembly sstl 2.5v 04 9 ddr sdram device cycle time at cl=2.5 7ns 7.5ns 8ns 70 75 80 10 ddr sdram device access time from clock at cl=2.5 0.75ns 0.75ns 0.8ns 75 75 80 11 dimm configuration type ecc 0 2 12 refresh rate/type 15.62 5 us / sr 8 0 13 primary ddr sdram width x 4 0 4 14 error checking ddr sdram device width x4 0 4 15 ddr sdram device attr: min c l k delay, random col access 1 clock 01 16 ddr sdram device attributes: burst length supported 2,4,8 0e 17 ddr sdram device attributes: number of device banks 4 04 18 ddr sdram device attributes: cas latencies supported 2/2.5 2/2.5 2/2.5 0c 0c 0c 19 ddr sdram device attributes: cs latency 0 01 20 ddr sdram device attributes: we latency 1 02 21 ddr sdram device attribut es: differential clock, pll, register 26 22 ddr sdram device attributes: general +/ - 0.2v voltage tolerance 00 23 minimum clock cycle at cl=2 7.5ns 10ns 10ns 75 a0 a0 24 maximum data access time from clock at cl=2 0.75ns 0.75ns 0.8ns 75 75 80 25 min imum clock cycle time at cl=1 n/a 00 26 maximum data access time from clock at cl=1 n/a 00 27 minimum row precharge time( t r p ) 20ns 20ns 20ns 50 50 50 28 minimum row active to row active delay ( t r rd ) 15ns 15ns 15ns 3c 3c 3c 29 minimum ras to cas del ay ( t r cd ) 20ns 20ns 20ns 50 50 50 30 minimum ras pulse width ( t ras ) 45ns 45ns 50ns 2d 2d 32 31 module bank density 256 mb 4 0 32 address and command setup time before clock 0.9ns 0.9ns 1.1ns 90 90 b0 33 address and command hold time after clock 0.9ns 0.9ns 1 .1 ns 90 90 b0 34 data input setup time before clock 0.5ns 0.5ns 0.6ns 50 50 60 35 data input hold time after clock 0.5ns 0.5ns 0.6ns 50 50 60 36 - 61 reserved undefined 00 62 spd revision initial initial initial 00 00 00 63 checksum data df 0f 95
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 6 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. serial presence detect -- part 2 of 2 64 mx 72 1 bank registered ddr sdram dimm based on 64 mx 4 , 4banks, 8k refresh, 2.5 v ddr sdrams with sp d spd entry value serial pd data entry (hexadecimal) byte description ddr266a - 7k ddr266b - 75b dd r200 - 8b ddr266a - 7k ddr266b - 75 ddr200 - 8b note 64 - 71 manufacturer?s jeded id code nanya 7f7f7f0b 00000000 72 module manufacturing location n/a 00 73 - 90 module part number n/a n/a n/a 00 00 00 91 - 92 module revision code n/a 00 93 - 94 module manufactur ing data year/week code yy/ww 1,2 95 - 98 module serial number serial number 00 99 - 255 reserved undefined 00 1. yy= binary coded decimal year code, 0 - 99(decimal) , 00 - 63(hex) 2. ww= binary coded decimal year code, 01 - 52(decimal) , 01 - 34(hex)
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 7 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. absolute maximum ratings symbol parameter rating units v in , v out voltage on i/o pins relative to vss - 0.5 to v ddq +0.5 v v in voltage on input relative to vss - 0.5 to +2.7 v v dd voltage on vdd supply relative to vss - 0.5 to +2.7 v v dd q voltage on vddq supply relative to vss - 0.5 to +2.7 v t a operating temperature (ambient) 0 to +70 c t stg storage temperature (plastic) - 55 to +150 c p d power dissipation 18 w i out short circuit output current 50 ma note : stresses greater t han those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sec ti ons of this specif ication is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. capacitance parameter symbol max. units notes input capacitance: ck0, ck0 c i1 7 pf 1 input capacitance: a0 - a1 2 , ba0, ba1, we , ras , cas , cke0, s0 c i2 7 pf 1 input capacitance: reset c i3 7 pf 1 input capacitance: sa0 - sa2, scl c i4 9 pf 1 input/output capacitance dq0 - 63; dqs0 - 1 7, cb0 - 7 c io1 10 pf 1,2 input/output capacitance: sda c io3 11 pf 1. v ddq = v dd = 2.5v 0.2v, f = 100 mhz, t a = 2 5 c , v out (dc) = v ddq /2, v out (peak to peak) = 0.2v. 2. d m inputs are grouped with i/o pins reflecting the fact that they are matched in l oading to dq and dqs to facilitate trace matching at the board level.
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 8 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. dc electrical characteristics and operating conditions ( t a = 0 c ~ 7 0 c ; v ddq = 2.5v 0 .2v; v dd = 2.5v 0.2 v, see ac characteristics) symbol para meter min max units notes v dd supply voltage 2.3 2.7 v 1 v dd q i/o supply voltage 2.3 2.7 v 1 v ss , v ssq supply voltage , i/o supply voltage 0 0 v v ref /o reference voltage 0.49 x v dd q 0.51 x v dd q v 1,2 v tt i/o termination voltage (system) v ref ? 0 .04 v ref + 0.04 v 1,3 v ih(dc) input high (logic1) voltage v ref + 0.15 v ddq + 0.3 v 1 v il(dc) input low (logic0) voltage - 0.3 v ref - 0. 15 v 1 v in(dc) input voltage level, ck and ck inputs - 0.3 v ddq + 0.3 v 1 v id(dc) input differential vo ltage, ck and ck inputs 0.30 v ddq + 0.6 v 1,4 i i input leakage current any input 0v v in v dd ; (all other pins not under test = 0v) - 5 5 ua 1 i oz output leakage current (dqs are disabled; 0v v out v ddq - 5 5 ua 1 i oh output hig h current (v out = v ddq - 0.373v, min v ref , min v tt ) - 16.8 - ma 1 i ol output low current (v out = 0 .373, max v ref , max v tt ) 16.8 - ma 1 1. inputs are not recognized as valid until v ref stabilizes. 2. v ref is expected to be equal to 0.5 v ddq of the tran smitting device, and to track variations in the dc level of the same. peak - to - peak noise on v ref may not exceed 2% of the dc value. 3. v tt is not applied directly to the dimm. v tt is a system supply for signal termination resistors, is expected to be set equal to v ref , and must track variations in the dc level of v ref . 4. v id is the magnitude of the difference between the input level on ck and the input level on ck .
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 9 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. ac characteristics (notes 1 - 5 apply to th e following tables; electrical characteristics and dc operating conditions, ac operating conditions, operating, standby, and refresh currents, and electrical characteristics and ac timing.) 1. all voltages referenced to v ss . 2. tests for ac timing, i dd , and electrical, ac and dc characteristics, may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. outputs measured with equivalent load. refer to the ac output load circuit below. 4. ac timing and i dd tests may use a v il to v ih swing of up to 1.5v in the test environment, but input timing is still referenced to v ref (or to the crossing point for ck, ck), and parameter specifications are guarant eed for the specified ac input levels under normal use conditions. the minimum slew rate for the input signals is 1v/ns in the range between v il(ac) and v ih(ac) unless otherwise specified. 5. the ac and dc input level specifications are as defined in the s stl_2 standard (i.e. the receiver effectively switches as a result of the signal crossing the ac input level, and remains in that state as long as the signal does not ring back above (below) the dc input low (high) level. ac output load circuits timing reference point v tt 50 ohms 30 pf output v out ac operating conditions ( t a = 0 c ~ 7 0 c ; v ddq = 2.5v 0 .2v; v dd = 2.5v 0.2 v, see ac characteristics) symbol parameter/condition min max unit notes v ih(ac) input high (logic 1) voltage. v ref + 0.31 - v 1, 2 v il(ac) input l ow (logic 0) voltage. - v ref ? - 0.31 v 1, 2 v id(ac) input differential voltage, ck and ck inputs 0. 7 v ddq + 0.6 v 1, 2, 3 v ix(ac) input differential pair cross point voltage, ck and ck inputs (0.5*v ddq ) - 0 .2 (0.5*v ddq ) + ? 0.2 v 1, 2, 4 1. input slew rate = 1v/ n s . 2. inputs are not recognized as valid until v ref stabilizes. 3. v id is the magnitude of the difference between the input level on ck and the input level on ck. 4. the value of v ix is expected to equal 0.5*v ddq of the transm itting device and must track variations in the dc level of the same.
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 10 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. operating, standby, and refresh currents ( t a = 0 c ~ 7 0 c ; v ddq = 2.5v 0 .2v; v dd = 2.5v 0.2 v, see ac characteristics) symbol parameter/condition pc1600 pc2100 unit notes i dd0 operating current : one bank; active / precharge; t rc = t rc ( min ) ; t ck = t ck ( min ) ; dq, dm, and dqs inputs changing twice per clock cycle; address and control inputs changing once per clock cycle 2180 2470 ma 1 i dd1 operating current : one bank; active / read / precharge; burst = 2; t rc = t rc ( min ) ; cl=2.5; t ck = t ck ( min ) ; i out = 0ma; address and control inputs changing once per clock cycle 2450 2990 ma 1 i dd 2p precharge power - down standby current : all banks idle; power - down m ode; cke v il ( max ) ; t ck = t ck ( min ) 1100 1100 ma 1 i dd2n idle standby current : cs 3 v ih ( min ) ; all banks idle; cke 3 v ih ( min ) ; t ck = t ck ( min ) ; address and control inputs changing once per clock cycle 1370 1600 ma 1 i dd3p active power - down stand by current : one bank active; power - down mode; cke v il ( max ) ; t ck = t ck ( min ) 1110 1100 ma 1 i dd3n active standby current : one bank; active / precharge; cs 3 v ih ( min ) ; cke 3 v ih ( min ) ; t rc = t ras ( max ) ; t ck = t ck ( min ) ; dq, dm, and dqs inputs c hanging twice per clock cycle; address and control inputs changing once per clock cycle 1730 2078 ma 1 i dd4r operating current : one bank; burst = 2; reads; continuous burst; address and control inputs changing once per clock cycle; dq and dqs outputs changing twice per clock cycle; cl = 2.5; t ck = t ck ( min ) ; i out = 0ma 3170 4026 ma 1 i dd4w operating current : one bank; burst = 2; writes; continuous burst; address and control inputs changing once per clock cycle; dq and dqs inputs changing twice per clock cycle; cl=2.5; t ck = t ck ( min ) 2900 2840 ma 1 t rc = t rfc ( min ) 3710 3940 ma i dd 5 auto - refresh current : t rc = 15.625 s 1113 1113 ma 1,3 i dd6 self - refresh current : cke ?0.2v 61 61 ma 1 1. i dd specifications are tested after the d evice is properly initialized. 2. enables on - chip refresh and address counters. 3 . current at 7.8 s is time averaged value of i dd5 at t rfc ( min ) and i dd2p over 15.625 s.
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 11 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. ac timing speci fi cations for ddr sdram devices used on module ( t a = 0 c ~ 7 0 c ; v ddq = 2.5v 0 .2v; v dd = 2.5v 0.2 v, see ac characteristics) (part 1 of 2) - 7k - 75b - 8b symbol parameter min. max. min. max. min. max. unit note s t ac dq output access time from ck/ ck - 0.75 +0.75 - 0.75 +0.75 - 0 .8 +0.8 ns 1,2,3,4 t dqsck dqs output access time from ck/ ck - 0.75 +0.75 - 0.75 +0.75 - 0.8 +0.8 ns 1,2,3,4 t ch ck high - level width 0.45 0.55 0.45 0.55 0.45 0.55 t ck 1,2,3,4 t cl ck low - level width 0.45 0.55 0.45 0.55 0.45 0.55 t ck 1,2, 3,4 t ck cl=2.5 7 12 7.5 12 8 12 ns 1,2,3,4 t ck clock cycle time cl=2 7.5 12 10 12 10 12 ns 1,2,3,4 t dh dq and dm input hold time 0.5 0.5 0.6 ns 1,2,3,4 ,1 5 , 16 t ds dq and dm input setup time 0.5 0.5 0.6 ns 1,2,3,4 ,1 5 , 16 t dipw dq and dm input puls e width (each input) 1.75 1.75 2 ns 1,2,3,4 t hz data - out high - impedance time from ck/ ck - 0.75 +0.75 - 0.75 +0.75 - 0.8 +0.8 ns 1, 2, 3, 4, 5 t lz data - out low - impedance time from ck / ck - 0.75 +0.75 - 0.75 +0.75 - 0. 8 +0.8 ns 1, 2, 3, 4, 5 t dqsq dqs - dq skew (dqs & associated dq signals) 0.5 0.5 0.6 ns 1,2,3,4 t dqsqa dqs - dq skew (dqs & all dq signals) 0.5 0.5 0.6 ns 1,2,3,4 t hp minimum half clk period for any given cycle; defined by clk high (t ch ) or clk low (t cl ) time t ch or t cl t ch or t cl t ch or t cl t ck 1,2,3,4 t qh data output hold time from dqs t hp - 0.75ns t hp - 0.75ns t hp - 1.0ns t ck 1,2,3,4 t dqss write command to 1st dqs latching transition 0.75 1.25 0.75 1.25 0.75 1.25 t ck 1,2,3,4 t dqsl,h dqs input low (high) pulse width (write cycle) 0.35 0.35 0.35 t ck 1,2,3,4 t dss dqs falling edge to ck setup time (write cycle) 0.2 0.2 0.2 t ck 1,2,3,4 t dsh dqs falling edge hold time from ck (write cycle) 0.2 0.2 0.2 t ck 1,2,3,4 t mrd mode register set command cycle time 14 15 16 ns 1,2,3,4 t wpres write preamble setup time 0 0 0 ns 1, 2, 3, 4, 7 t wpst write postamble 0.40 0.60 0.40 0.60 0.40 0.60 t ck 1, 2, 3, 4, 6 t wpre write preamble 0.25 0.25 0.25 t ck 1,2,3,4 t ih address and control i nput hold time (fast slew rate) 0.9 1.1 1.1 ns 2, 3, 4, 9 , 1 1 , 1 2 t is address and control input setup time (fast slew rate) 0.9 1.1 1.1 ns 2, 3, 4, 9 , 11 , 1 2 t ih address and control input hold time (slow slew rate) 1.0 1.1 1.1 ns 2, 3, 4, 1 0 , 1 1 , 1 2 , 14
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 12 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. ac timing specifications for ddr sdram devices used on module ( t a = 0 c ~ 7 0 c ; v ddq = 2.5v 0 .2v; v dd = 2.5v 0.2 v, see ac characteristics) (part 2 of 2) - 7k - 75b - 8b symbol parameter min. max. min. max. min. max. unit note s t is address and control input setup time (slow slewrate) 1.0 1.0 1.1 ns 2, 3, 4, 1 0 , 1 1 , 12 , 14 t ipw input pulse width 2.2 2.2 - ns 2, 3, 4, 12 t rpre read preamble 0.9 1.1 0.9 1.1 0.9 1.1 t ck 1,2,3,4 t rpst read postamble 0.40 0.60 0.40 0.60 0.40 0.60 t ck 1,2,3,4 t ras active to precharge command 45 120,000 45 120,000 50 120,000 ns 1,2,3,4 t rc active to active/auto - refresh command period 65 65 70 ns 1,2,3,4 t rfc auto - refresh to active/auto - refresh command period 75 75 80 ns 1,2,3,4 t rcd ac tive to read or write delay 20 20 20 ns 1,2,3,4 t rap active to read command with autoprecharge 20 20 20 ns 1,2,3,4 t rp precharge command period 20 20 20 ns 1,2,3,4 t rrd active bank a to active bank b command 15 15 15 ns 1,2,3,4 t wr write re covery time 15 15 15 ns 1,2,3,4 t dal auto precharge write recovery + precharge time (t wr / t ck ) + (t rp / t ck ) (t wr / t ck ) + (t rp / t ck ) (t wr / t ck ) + (t rp / t ck ) t ck 1, 2, 3, 4, 1 3 t wtr internal write to read command delay 1 1 1 t ck 1,2 , 3,4 t xsnr exit self - refresh to non - read command 75 75 80 ns 1,2 , 3,4 t xsrd exit self - refresh to read command 200 200 200 t ck 1,2 , 3,4 t refi average periodic refresh interval 15.625 15.625 15.625 s 1, 2, 3, 4, 8
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 13 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. ac timing specification not es 1. input slew rate = 1v/ns. 2. the ck/ ck input reference level (for timing reference to ck/ ck ) is the point at which ck and ck cross: the input reference level for signals other than ck/ ck , is v ref . 3. inputs are not recognized as valid until v ref stabilizes. 4. the output timing reference level, as measured at the timing reference point indicated in ac characteristics (note 3) is v tt . 5. t hz and t lz transitions occur in the same access time windows as valid data transitions. these parameters are not referred to a specific voltage level, but specify when the device is no longer driving (hz), or begins driving (lz). 6. the maximum limit for this parameter is not a device li mit. the device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 7. the specific requirement is that dqs be valid (high, low, or some point on a valid transition) on or before this ck edge. a v alid transition is defined as monotonic and meeting the input slew rate specifications of the device. when no writes were previously in progress on the bus, dqs will be transitioning from hi - z to logic low. if a previous write was in progress, dqs could be high, low, or transitioning from high to low at this time, depending on t dqss . 8. a maximum of eight auto refresh commands can be posted to any given ddr sdram device. 9 . for command/address input slew rate >= 1.0 v/ns. slew rate is measured between v oh (ac) and v ol (ac). 10 . for command/address input slew rate >= 0.5 v/ns and < 1.0 v/ns. slew rate is measured between v oh (ac) and v ol (ac). 1 1 . ck/ ck slew rates are >= 1.0 v/ns. 1 2 . these parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by design or tester characterization. 1 3 . for each of the terms in parentheses, if not already an integer, round to the next highest integer. t ck is equal to the actual system clock cycle time. for example, for pc2100 at cl= 2.5, t dal = (15ns/7.5ns) +(20ns/7.0ns) = 2 + 3 = 5. 1 4 . an input setup and hold time derating table is used to increase t is and t ih in the case where the input slew rate is below 0.5 v/ns. input slew rate ? delta ( t i s ) delta ( t ih ) unit note 0.5 v/ns 0 0 ps 1,2 0. 4 v/ns +50 0 ps 1,2 0. 3 v/ns +100 0 ps 1,2 1. input slew rate is based on the lesser of the slew rates determined by either v ih (ac) to v il (ac) or v ih (dc) to v il (dc) , similarly for rising transi tions. 2. these derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device. 1 5 . an input setup and hold time derating table is used to increase t ds and t dh in the case where the i/o slew rate is below 0.5 v/ns. input slew rate delta ( t d s ) delta ( t dh ) unit note 0.5 v/ns 0 0 ps 1,2 0. 4 v/ns +75 +75 ps 1,2 0. 3 v/ns +150 +150 ps 1,2 1. i/o slew rate is based on the lesser of the slew rates determined by either v ih (ac) to v il (ac) or v i h (dc) to v il (dc) , similarly for rising transitions. 2. these derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device. 1 6 . an i/o delta rise, fall derating table is used to increase t ds and t dh in the case where dq, dm, and dqs slew rates differ. delta rise and fall rate delta ( t d s ) delta ( t dh ) unit note 0.0 ns/v 0 0 ps 1,2,3,4 0.25 ns/v +50 +50 ps 1,2,3,4 0.5 ns/v +100 +100 ps 1,2,3,4 1. input slew rate is based on the lesser of the slew rates determined by either v ih (ac) to v il (ac) or v ih (dc) to v il (dc) , similarly for rising transitions. 2. input slew rate is based on the larger of ac to ac delta rise, fall rate and dc to dc delta rise, fall rate. 3. the delta rise, fal l rate is calculated as: [1/(slew rate 1)] - [1/(slew rate 2)] for example: slew rate 1 = 0.5 v/ns; slew rate 2 = 0.4 v/ns . delta rise, fall = (1/0.5) - (1/ 0.4) [ns/v] = - 0.5 ns/v using the table above, this would result in an increase in t ds and t dh of 100 ps. 4. these derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device.
nt 256d72s4pa0gr 256mb : 32 m x 72 register ed ddr sdram dimm preliminary 0 8/0 1 14 ? nanya technology corp. nanya technology corp. reserves the right to change products and specificat ions without notice. package dimensions note : all dimensions are typical unless otherwise stated. 133.35 131.35 128.95 (2x) 4.00 front side 1.80 detail a 0.050 detail b 1.00 width 3.99 back 43.33 17.80 10.0 register register pll 2.3 (front) 4.24 1.27 unit : millimeters(inches) 5.250 5.171 5.077 0.157 0.091 0.700 1.700 0.157 max. 0.167 0.050 0.098 q 2.5 0.394 0.071 detail a detail b 3.80 0.15 0.157 4.00 0.039 1.27 pitch


▲Up To Search▲   

 
Price & Availability of NT256D72S4PA0GR-75B

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X