Part Number Hot Search : 
HC1G14 FLK15LED B39202 CY4DSMD RT600 PJ1MPXX LBN7015 C339C
Product Description
Full Text Search
 

To Download AD7691-15 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  18-bit, 1.5 lsb inl, 250 ksps pulsar differential adc in msop/lfcsp data sheet ad7691 rev. d document feedback information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 ?2006C2014 analog devices, inc. all rights reserved. technical support www.analog.com features 18-bit resolution with no missing codes throughput: 250 ksps inl: 0.75 lsb typical, 1.5 lsb maximum (6 ppm of fsr) dynamic range: 102 db typical at 250 ksps oversampled dynamic range: 125 db at1 ksps noise-free code resolution: 20 bits at 1 ksps effective resolution: 22.7 bits at 1 ksps sinad: 101.5 db typical at 1 khz thd: ?125 db typical at 1 khz true differential analog input range: v ref 0 v to v ref with v ref up to vdd on both inputs no pipeline delay single-supply 2.3 v to 5 v operation with 1.8 v/2.5 v/3 v/5 v logic interface proprietary serial interface spi/qspi/microwire?/dsp compatible ability to daisy-chain multiple adcs optional busy indicator feature power dissipation 1.35 mw at 2.5 v/100 ksps, 4 mw at 5 v/100 ksps 1.4 w at 2.5 v/100 sps standby current: 1 na 10-lead packages: msop (msop-8 size) and 3 mm 3 mm lfcsp (sot-23 size) pin-for-pin compatible with the18-bit ad7690 and 16-bit ad7693 , ad7688 , and ad7687 applications battery-powered equipment data acquisitions seismic data acquisition systems instrumentation medical instruments figure 1. integral nonlinearity vs. code, 5 v application diagram figure 2. table 1. msop, lfcsp/sot-23 14-/16-/18-bit pulsar? adc type 100 ksps 250 ksps 400 ksps to 500 ksps 1000 ksps adc driver 18-bit true differential ad7691 ad7690 ad7982 ad7984 ada4941-1 ada4841-x 16-bit true differential ad7684 ad7687 ad7688 ad7693 ada4941-1 ada4841-x 16-bit pseudo differential ad7680 ad7683 ad7685 ad7694 ad7686 ad7980 ada4841-x 14-bit pseudo differential ad7940 ad7942 ad7946 ada4841-1 general description the ad7691 1 is an 18-bit, charge redistribution, successive approximation, analog-to-digital converter (adc) that operates from a single power supply, vdd, between 2.3 v and 5 v. it contains a low power, high speed, 18-bit sampling adc with no missing codes, an internal conversion clock, and a versatile serial interface port. on the cnv rising edge, it samples the voltage difference between the in+ and in? pins. the voltages on these pins swing in opposite phases between 0 v and ref. the reference voltage, ref, is applied externally and can be set up to the supply voltage. the parts power scales linearly with throughput. the spi-compatible serial interface also features the ability, using the sdi input, to daisy-chain several adcs on a single 3-wire bus and provides an optional busy indicator. it is compatible with 1.8 v, 2.5 v, 3 v, or 5 v logic, using the separate vio supply. the ad7691 is housed in a 10-lead msop or a 10-lead lfcsp with operation specified from ?40c to +85c. 1 protected by u.s. patent 6,703,961. 1.5 ?1.5 0 262144 code inl (lsb) 1.0 0.5 0 ?0.5 ?1.0 65536 131072 196608 positive inl = 0.43lsb negative inl = ?0.62lsb 06146-025 ad7691 ref gnd vdd in+ in? vio sdi sck sdo cnv +1.8v to vdd 3- or 4-wire interface (spi, daisy chain, cs) +0.5v to vdd 10v, 5v, ... +2.5v to +5v ada4941 0 6146-001
ad7691 data sheet rev. d | page 2 of 28 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 application diagram ........................................................................ 1 general description ......................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 timing specifications .................................................................. 5 absolute maximum ratings ............................................................ 7 thermal resistance ...................................................................... 7 esd caution .................................................................................. 7 pin configurations and function descriptions ........................... 8 typical performance characteristics ............................................. 9 terminology .................................................................................... 13 theory of operation ...................................................................... 14 circuit information .................................................................... 14 converter operation .................................................................. 14 typical connecti on diagram ................................................... 15 analog inputs .............................................................................. 15 driver amplifier choice ........................................................... 16 single-to-differential driver .................................................... 16 voltage reference input ............................................................ 16 power supply ............................................................................... 17 supplying the adc from the reference .................................. 17 digital interface .......................................................................... 17 cs mode, 3-wire without busy indicator ............................. 18 cs mode, 3-wire with busy indicator .................................... 19 cs mode, 4-wire without busy indicator ............................. 20 cs mode, 4-wire with busy indicator .................................... 21 chain mode without busy indicator ...................................... 22 chain mode with busy indicator ............................................. 23 application hints ........................................................................... 24 layout .......................................................................................... 24 evaluating the ad7691 performance ...................................... 24 outline dimensions ....................................................................... 25 ordering guide .......................................................................... 25 revision history 7/14rev. c to rev. d changed qfn (lfcsp) to lfcsp .............................. throughout changes to features section............................................................ 1 added patent note, note 1 .............................................................. 1 change to acquisition time parameter, table 5 .......................... 6 changes to evaluating the ad7691 performance section ........ 24 updated outline dimensions ....................................................... 25 changes to ordering guide .......................................................... 25 3/12rev. b to rev. c change to table 9 ........................................................................... 14 changes to ordering guide .......................................................... 25 7/11rev. a to rev. b changes to common-mode input range min parameter ......... 3 added epad note to figure 6 and table 8 ................................... 8 updated outline dimensions ....................................................... 25 11/07rev. 0 to rev. a deleted qfn package in development references ....... universal changes to features, applications, figure 1 and figure 2 ........... 1 changes to accuracy, table 2 .......................................................... 3 changes to power dissipation, table 3 ........................................... 4 added thermal resistance section ................................................ 7 changes to figure 22...................................................................... 11 changes to format ......................................................................... 12 changes to terminology section ................................................. 13 changes to format and figure 29 ................................................ 15 inserted figure 31 ........................................................................... 15 changes to format ......................................................................... 17 changes to figure 44...................................................................... 22 changes to figure 46...................................................................... 23 updated qfn outline dimensions ............................................. 25 changes to ordering guide .......................................................... 25 7/06revision 0: initial version
data sheet ad7691 rev. d | page 3 of 28 specifications vdd = 2.3 v to 5.25 v, vio = 2.3 v to vdd, v ref = vdd, all specifications t min to t max , unless otherwise noted. table 2. parameter conditions/comments min typ max unit resolution 18 bits analog input voltage range, v in in+ ? (in?) ?v ref +v ref v absolute input voltage in+, in? ?0.1 v ref + 0.1 v common-mode input range in+, in? v ref /2 ? 0.1 v ref /2 v ref /2 + 0.1 v analog input cmrr f in = 250 khz 65 db leakage current at 25c acquisition phase 1 na input impedance 1 throughput conversion rate vdd = 4.5 v to 5.25 v 0 250 ksps vdd = 2.3 v to 4.5 v 0 180 ksps transient response full-scale step 1.8 s accuracy no missing codes 18 bits integral linearity error ?1.5 0.75 +1.5 lsb 2 differential linearity error ?1 0.5 +1.25 lsb 2 transition noise ref = vdd = 5 v 0.75 lsb 2 gain error 3 vdd = 4.5 v to 5.25 v ?40 2 +40 lsb 2 vdd = 2.3 v to 4.5 v ?80 2 +80 lsb 2 gain error temperature drift 0.3 ppm/c zero error 3 vdd = 4.5 v to 5.25 v ?0.8 0.1 +0.8 mv vdd = 2.3 v to 4.5 v ?3.5 0.7 +3.5 mv zero temperature drift 0.3 ppm/c power supply sensitivity vdd = 5 v ? 5% 0.25 lsb 2 ac accuracy 4 dynamic range v ref = 5 v 101 102 db oversampled dynamic range 5 f in = 1 ksps 125 db signal-to-noise f in = 1 khz, v ref = 5 v 100 101.5 db f in = 1 khz, v ref = 2.5 v 95 96.5 db spurious-free dynamic range f in = 1 khz, v ref = 5 v ?125 db total harmonic distortion f in = 1 khz, v ref = 5 v ?118 db signal-to-(noise + distortion) f in = 1 khz, v ref = 5 v 100 101.5 db f in = 1 khz, v ref = 2.5 v 95 96.5 db intermodulation distortion 6 115 db 1 see the analog inputs section. 2 lsb means least significant bit. with the 5 v input range, one lsb is 38.15 v. 3 see the terminology section. these specif ications include full temperature range variation but not the error contribution from the external reference. 4 all ac accuracy specifications in db are referred to a full-scale input fsr. tested with an input signal at 0.5 db below full scale, unless otherwise specified. 5 dynamic range obtained by oversampli ng the adc running at a throughput f s of 250 ksps, followed by postdigital fi ltering with an outp ut word rate f o . 6 f in1 = 21.4 khz and f in2 = 18.9 khz, with each tone at ?7 db below full scale.
ad7691 data sheet rev. d | page 4 of 28 vdd = 2.3 v to 5.25 v, vio = 2.3 v to vdd, v ref = vdd, all specifications t min to t max , unless otherwise noted. table 3. parameter conditions/comments min typ max unit reference voltage range 0.5 vdd + 0.3 v load current 250 ksps, ref = 5 v 60 a sampling dynamics ?3 db input bandwidth 2 mhz aperture delay vdd = 5 v 2.5 ns digital inputs logic levels v il ?0.3 +0.3 vio v v ih 0.7 vio vio + 0.3 v i il ?1 +1 a i ih ?1 +1 a digital outputs data format serial 18-bit, twos complement pipeline delay 1 v ol i sink = +500 a 0.4 v v oh i source = ?500 a vio ? 0.3 v power supplies vdd specified performance 2.3 5.25 v vio specified performance 2.3 vdd + 0.3 v vio range 1.8 vdd + 0.3 v standby current 2, 3 vdd and vio = 5 v, t a = 25c 1 50 na power dissipation vdd = 2.5 v, 100 sps throughput 1.4 w vdd = 2.5 v, 100 ksps throughput 1.35 mw vdd = 2.5 v, 180 ksps throughput 2.4 mw vdd = 5 v, 100 ksps throughput 4.24 5 mw vdd = 5 v, 250 ksps throughput 10.6 12.5 mw energy per conversion 50 nj/sample temperature range 4 specified performance t min to t max ?40 +85 c 1 conversion results are available imme diately after completed conversion. 2 with all digital inputs forced to vio or gnd as required. 3 during acquisition phase. 4 contact an analog devices, inc., sales representative for the extended temperature range.
data sheet ad7691 rev. d | page 5 of 28 timing specifications vdd = 4.5 v to 5.25 v, vio = 2.3 v to vdd, v ref = vdd, all specifications t min to t max , unless otherwise noted. 1 table 4. parameter symbol min typ max unit conversion time: cnv rising edge to data available t conv 0.5 2.2 s acquisition time t acq 1.8 s time between conversions t cyc 4 s cnv pulse width (cs mode) t cnvh 10 ns sck period (cs mode) t sck 15 ns sck period (chain mode) t sck vio above 4.5 v 17 ns vio above 3 v 18 ns vio above 2.7 v 19 ns vio above 2.3 v 20 ns sck low time t sckl 7 ns sck high time t sckh 7 ns sck falling edge to data remains valid t hsdo 4 ns sck falling edge to data valid delay t dsdo vio above 4.5 v 14 ns vio above 3 v 15 ns vio above 2.7 v 16 ns vio above 2.3 v 17 ns cnv or sdi low to sdo d17 msb valid (cs mode) t en vio above 4.5 v 15 ns vio above 2.7 v 18 ns vio above 2.3 v 22 ns cnv or sdi high or last sck falling edge to sdo high impedance (cs mode) t dis 25 ns sdi valid setup time from cnv rising edge (cs mode) t ssdicnv 15 ns sdi valid hold time from cnv rising edge (cs mode) t hsdicnv 0 ns sck valid setup time from cnv rising edge (chain mode) t ssckcnv 5 ns sck valid hold time from cnv rising edge (chain mode) t hsckcnv 10 ns sdi valid setup time from sck falling edge (chain mode) t ssdisck 3 ns sdi valid hold time from sck falling edge (chain mode) t hsdisck 4 ns sdi high to sdo high (chain mode with busy indicator) t dsdosdi vio above 4.5 v 15 ns vio above 2.3 v 26 ns 1 see figure 3 and figure 4 for load conditions.
ad7691 data sheet rev. d | page 6 of 28 vdd = 2.3 v to 4.5 v, vio = 2.3 v to vdd, v ref = vdd, all specifications t min to t max , unless otherwise noted. 1 table 5. parameter symbol min typ max unit conversion time: cnv rising edge to data available t conv 0.5 3.7 s acquisition time t acq 1.8 s time between conversions t cyc 5.5 s cnv pulse width (cs mode) t cnvh 10 ns sck period (cs mode) t sck 25 ns sck period (chain mode) t sck vio above 3 v 29 ns vio above 2.7 v 35 ns vio above 2.3 v 40 ns sck low time t sckl 12 ns sck high time t sckh 12 ns sck falling edge to data remains valid t hsdo 5 ns sck falling edge to data valid delay t dsdo vio above 3 v 24 ns vio above 2.7 v 30 ns vio above 2.3 v 35 ns cnv or sdi low to sdo d17 msb valid (cs mode) t en vio above 2.7 v 18 ns vio above 2.3 v 22 ns cnv or sdi high or last sck falling edge to sdo high impedance (cs mode) t dis 25 ns sdi valid setup time from cnv rising edge (cs mode) t ssdicnv 30 ns sdi valid hold time from cnv rising edge (cs mode) t hsdicnv 0 ns sck valid setup time from cnv rising edge (chain mode) t ssckcnv 5 ns sck valid hold time from cnv rising edge (chain mode) t hsckcnv 8 ns sdi valid setup time from sck falling edge (chain mode) t ssdisck 8 ns sdi valid hold time from sck falling edge (chain mode) t hsdisck 10 ns sdi high to sdo high (chain mode with busy indicator) t dsdosdi 36 1 see figure 3 and figure 4 for load conditions. figure 3. load circuit fo r digital interface timing figure 4. voltage levels for timing 500a i ol 500a i oh 1.4v to sdo c l 50pf 06146-002 30% vio 70% vio 2v or vio ? 0.5v 1 0.8v or 0.5v 2 0.8v or 0.5v 2 2v or vio ? 0.5v 1 t delay t delay 1 2v if vio above 2.5v, vio ? 0.5v if vio below 2.5v. 2 0.8v if vio above 2.5v, 0.5v if vio below 2.5v. 06146-003
data sheet ad7691 rev. d | page 7 of 28 absolute maximum ratings table 6. parameter rating analog inputs (in+, in?) 1 gnd ? 0.3 v to vdd + 0.3 v or 130 ma ref gnd ? 0.3 v to vdd + 0.3 v supply voltages vdd, vio to gnd ?0.3 v to +7 v vdd to vio 7 v digital inputs to gnd ?0.3 v to vio + 0.3 v digital outputs to gnd ?0.3 v to vio + 0.3 v storage temperature range ?65c to +150c junction temperature 150c lead temperature range jedec j-std-20 1 see the analog inputs section. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. thermal resistance ja is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. table 7. thermal resistance package type ja jc unit 10-lead msop 200 44 c/w 10-lead lfcsp 43.4 6.5 c/w esd caution
ad7691 data sheet rev. d | page 8 of 28 pin configurations and function descriptions figure 5. 10-lead msop pin configuration figure 6. 10-lead lfcsp pin configuration table 8. pin function descriptions pin no. mnemonic type 1 description 1 ref ai reference input voltage. the ref range is from 0.5 v to vdd. it is referred to the gnd pin. this pin should be decoupled closely to the pin with a 10 f capacitor. 2 vdd p power supply. 3 in+ ai differential positive analog input. referenced to in?. the input range for in+ is between 0 v and v ref , centered about v ref /2 and must be driven 180 out of phase with in?. 4 in? ai differential negative analog input. referenced to in+. the input range for in? is between 0 v and v ref , centered about v ref /2 and must be driven 180 out of phase with in+. 5 gnd p power supply ground. 6 cnv di convert input. this input has multiple functions. on its leading edge, it initiates the conversions and selects the interface mode of the part, either chain or cs mode. in cs mode, it enables the sdo pin when low. in chain mode, the data should be read when cnv is high. 7 sdo do serial data output. the conversion result is output on this pin. it is synchronized to sck. 8 sck di serial data clock input. when the part is select ed, the conversion result is shifted out by this clock. 9 sdi di serial data input. this input provides multiple features. it selects the interface mode of the adc as follows: chain mode is selected if sdi is low during the cnv risi ng edge. in this mode, sdi is used as a data input to daisy-chain the conversion results of two or more adcs onto a single sdo line. the digital data level on sdi is output on sdo with a delay of 18 sck cycles. cs mode is selected if sdi is high during the cnv risi ng edge. in this mode, either sdi or cnv can enable the serial output signals when low, and if sdi or cnv is low when the conversion is complete, the busy indicator feature is enabled. 10 vio p input/output interface digital power. nominally at the same supply as the host interface (1.8 v, 2.5 v, 3 v, or 5 v ). epad exposed pad. the exposed pad is not connected internally. for increased reliability of the solder joints, it is recommended that the pad be soldered to the ground plane. 1 ai = analog input, di = digital input, do = digital output, and p = power. ref 1 vdd 2 in+ 3 in? 4 gnd 5 vio 10 sdi 9 sck 8 sdo 7 cnv 6 ad7691 top view (not to scale) 06146-004 06146-005 1 ref 2 vdd 3 in+ 4 in? 5 gnd 10 vio 9sdi 8sck 7sdo 6 cnv top view (not to scale) ad7691 notes 1. the exposed pad is not connected internally. for increased reliability of the solder joints, it is recommended that the pad be soldered to the ground plane.
data sheet ad7691 rev. d | page 9 of 28 typical performance characteristics figure 7. integral nonlinearity vs. code 2.5 v figure 8. histogram of a dc input at the code center, 5 v figure 9. 2 khz fft plot, 5 v figure 10. differential nonlinearity vs. code, 5 v figure 11. histogram of a dc input at the code center, 2.5 v figure 12. 2 khz fft plot, 2.5 v 1.5 ?1.5 0 262144 code inl (lsb) 1.0 0.5 0 ?0.5 ?1.0 65536 131072 196608 positive inl = 0.39lsb negative inl = ?0.73lsb 06146-026 80k 0 25 code in hex counts 70k 60k 50k 40k 30k 20k 10k 26 27 28 29 2a 2b 2c 2d 2e 2f 0 0 26 2062 14 0 0 2904 69769 28527 27770 vdd = ref = 5v = 0.76lsb 06146-027 0 ?180 0 frequency (khz) amplitude (db of full scale) ?20 ?40 ?60 ?80 ?100 ?120 ?140 ?160 20 40 60 80 100 120 32768 point fft vdd = ref = 5v f s = 250ksps f in = 2khz snr = 101.4db thd = ?120.1db 2nd harmonic = ?140.7db 3rd harmonic = ?120.3db 06146-028 1.0 ?1.0 0 262144 code dnl (lsb) 0.5 0 ?0.5 65536 131072 196608 positive dnl = 0.37lsb negative dnl = ?0.33lsb 06146-029 45k 0 code in hex counts 2423 25 26 28 29 2b2a 2c 2d 2f2e 30 31 01229 501 910 78 9 0 17460 28179 vdd = ref = 2.5v = 1.42lsb 14362 24411 27 2997 38068 06146-030 40k 35k 30k 25k 20k 15k 10k 5k 4055 0 ?180 0 frequency (khz) amplitude (db of full scale) ?20 ?40 ?60 ?80 ?100 ?120 ?140 ?160 2010 30 40 50 60 70 80 90 32768 point fft vdd = ref = 2.5v f s = 180ksps f in = 2khz snr = 96.4db thd = ?120.3db 2nd harmonic = ?132.5db 3rd harmonic = ?121.2db 06146-031
ad7691 data sheet rev. d | page 10 of 28 figure 13. snr, sinad, and enob vs. reference voltage figure 14. snr vs. temperature figure 15. sinad vs. frequency figure 16. thd, sfdr vs. reference voltage figure 17. thd vs. temperature figure 18. thd vs. frequency 104 86 92 90 88 2.3 5.3 4.7 5.0 reference voltage (v) snr, sinad (db) 102 100 98 96 94 14 enob (bits) 18 17 16 15 2.6 2.9 3.2 3.5 3.8 4.1 4.4 enob sinad 06146-032 snr 105 100 95 90 85 80 ?55 125 temperature (c) snr (db) ?35 ?15 5 25 45 65 85 105 06146-033 v ref = 5v v ref = 2.5v 105 70 0 125 frequency (khz) sinad (db) 100 95 90 85 80 75 25 50 75 100 v ref = 5v, ?1db v ref = 2.5v, ?10db v ref = 2.5v, ?1db v ref = 5v, ?10db 06146-037 ? 105 ?135 ?125 ?130 2.3 5.3 reference voltage (v) thd, sfdr (db) 2.6 2.9 3.2 3.5 3.8 4.1 4.4 4.7 5.0 ?110 ?115 ?120 06146-038 thd sfdr ? 90 ?130 ?55 125 temperature (c) thd (db) ?35 ?15 5 25 45 65 85 105 v ref = 5v v ref = 2.5v ?100 ?110 ?120 06146-039 ? 60 ?130 0 125 frequency (khz) thd (db) ?70 ?80 ?90 ?100 ?110 ?120 25 50 75 100 v ref = 5v, ?1db v ref = 2.5v, ?10db v ref = 2.5v, ?1db v ref = 5v, ?10db 06146-040
data sheet ad7691 rev. d | page 11 of 28 figure 19. snr, thd vs. input level figure 20. operating current vs. temperature figure 21. operating current vs. supply figure 22. zero error, gain error vs. temperature figure 23. power-down current vs. temperature figure 24. t dsdo delay vs. capacitance load and supply 105 81 ?10 0 input level (db) snr (db) ?130 thd (db) ? 90 ?95 ?100 ?105 ?110 ?115 ?120 ?125 06146-041 102 99 96 93 90 87 84 ?8 ?6 ?4 ?2 snr 2.5v snr 5v thd 2.5v thd 5v temperature (c) operating current (a) 1000 750 500 250 0 ?55 ?35 ?15 5 25 45 65 85 105 125 vio vdd = 2.5v vdd = 5v 0 6146-042 f s =100ksps supply (v) operating current (a) 1000 750 500 250 0 2.3 2.6 2.9 3.2 3.5 3.8 4.1 4.4 4.7 5.0 5.3 vio vdd 0 6146-043 f s =100ksps 6 ?6 temperature (c) offset, gain error (lsb) ?55 125 4 2 0 ?2 ?4 ?35 ?15 5 25 45 65 85 105 gain error offset error 06146-044 temperature (c) power-down current (na) 1000 750 500 250 0 ?55 ?35 ?15 5 25 45 65 85 105 125 vdd + vio 0 6146-047 sdo capacitive load (pf) 120 0 20406080100 t dsdo delay (ns) 25 20 15 10 5 0 vdd = 5v, 85c vdd = 5v, 25c 0 6146-034
ad7691 data sheet rev. d | page 12 of 28 figure 25. pssr vs. frequency figure 26. analog input cmrr vs. frequency 95 65 1 10000 frequency (khz) psrr (db) 90 85 80 75 70 10 100 1000 06146-035 90 40 1 10000 frequency (khz) cmrr (db) 10 100 1000 85 80 75 70 65 60 55 50 45 v ref = vdd = 5v 06146-036
data sheet ad7691 rev. d | page 13 of 28 terminology least significant bit (lsb) the least significant bit, or lsb, is the smallest increment that can be represented by a converter. for an analog-to-digital converter with n bits of resolution, the lsb expressed in volts is n inpp v lsb 2 )v( ? integral nonlinearity error (inl) inl refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. the point used as negative full scale occurs ? lsb before the first code transition. positive full scale is defined as a level 1? lsb beyond the last code transition. the deviation is measured from the middle of each code to the true straight line (see figure 28). differential nonlinearity error (dnl) in an ideal adc, code transitions are 1 lsb apart. dnl is the maximum deviation from this ideal value. it is often specified in terms of resolution for which no missing codes are guaranteed. zero error zero error is the difference between the ideal midscale voltage, that is, 0 v, from the actual voltage producing the midscale output code, that is, 0 lsb. gain error the first transition (from 100 . . . 00 to 100 . . . 01) should occur at a level ? lsb above nominal negative full scale (?4.999981 v for the 5 v range). the last transition (from 011 10 to 011 11) should occur for an analog voltage 1? lsb below the nominal full scale (+4.999943 v for the 5 v range). the gain error is the deviation in lsbs (or % of full-scale range) of the difference between the actual level of the last transition and the actual level of the first transition from the difference between the ideal levels. the closely related full-scale error, which is expressed also in lsbs or % of full-scale range, includes the contribution from the zero error. spurious-free dynamic range (sfdr) sfdr is the difference, in decibels, between the rms amplitude of the input signal and the peak spurious signal. effective number of bits (enob) enob is a measurement of the resolution with a sine wave input. it is related to sinad by the following formula: enob = ( sinad db ? 1.76)/6.02 and is expressed in bits. noise-free code resolution it is the number of bits beyond which it is impossible to resolve individual codes distinctly. it is calculated as noise-free code resolution = log 2 (2 n / peak-to-peak noise ) and is expressed in bits. effective resolution it is calculated as effective resolution = log 2 (2 n / rms input noise ) and is expressed in bits. total harmonic distortion (thd) thd is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is expressed in decibels. dynamic range dynamic range is the ratio of the rms value of the full scale to the total rms noise measured with the inputs shorted together. the value for dynamic range is expressed in decibels. signal-to-noise ratio (snr) snr is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the nyquist frequency, excluding harmonics and dc. the value for snr is expressed in decibels. signal-to-(noise + distortion) ratio (sinad) sinad is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the nyquist frequency, including harmonics but excluding dc. the value for sinad is expressed in decibels. aperture delay aperture delay is the measure of the acquisition performance. it is the time between the rising edge of the cnv input and when the input signal is held for a conversion. transient resp onse transient response is the time required for the adc to acquire its input accurately after a full-scale step function is applied.
ad7691 data sheet rev. d | page 14 of 28 theory of operation figure 27. adc simplified schematic circuit information the ad7691 is a fast, low power, single-supply, precise, 18-bit adc using a successive approximation architecture. the part is capable of converting 250,000 samples per second (250 ksps) and powers down between conversions. when operating at 1 ksps, for example, it consumes 50 w typically, which is ideal for battery-powered applications. the ad7691 provides the user with an on-chip track-and-hold and does not exhibit pipeline delay or latency, making it ideal for multiple multiplexed channel applications. the ad7691 is specified from 2.3 v to 5.25 v and can be interfaced to any 1.8 v to 5 v digital logic family. it is housed in a 10-lead msop or a tiny 10-lead lfcsp that combines space savings and allows flexible configurations. the part is pin-for-pin compatible with the 18-bit ad7690 as well as the 16-bit ad7687 and ad7688. converter operation the ad7691 is a successive approximation adc based on a charge redistribution dac. figure 27 shows the simplified schematic of the adc. the capacitive dac consists of two identical arrays of 18 binary-weighted capacitors, which are connected to the two comparator inputs. during the acquisition phase, terminals of the array tied to the comparators input are connected to gnd via sw+ and sw?. all independent switches are connected to the analog inputs. thus, the capacitor arrays are used as sampling capacitors and acquire the analog signal on the in+ and in? inputs. when the acquisition phase is complete and the cnv input goes high, a conversion phase is initiated. when the conversion phase begins, sw+ and sw? are opened first. the two capacitor arrays are then disconnected from the inputs and connected to the gnd input. therefore, the differential voltage between the inputs in+ and in? captured at the end of the acquisition phase is applied to the comparator inputs, causing the comparator to become unbalanced. by switching each element of the capacitor array between gnd and ref, the comparator input varies by binary-weighted voltage steps (v ref /2, v ref /4 ... v ref /262,144). the control logic toggles these switches, starting with the msb, to bring the comparator back into a balanced condition. after the completion of this process, the part returns to the acquisition phase, and the control logic generates the adc output code and a busy signal indicator. because the ad7691 has an on-board conversion clock, the serial clock, sck, is not required for the conversion process. transfer functions the ideal transfer characteristic for the ad7691 is shown in figure 28 and table 9. figure 28. adc ideal transfer function tale 9. output codes and ideal input voltages description analog input v ref = 5 v digital output code (hex) fsr ? 1 lsb +4.999962 v 0x1ffff 1 midscale + 1 lsb +38.15 v 0x00001 midscale 0 v 0x00000 midscale ? 1 lsb ?38.15 v 0x3ffff ?fsr + 1 lsb ?4.999962 v 0x20001 ?fsr ?5 v 0x20000 2 1 this is also the code for an overranged analog input (v in+ ? v in? above v ref ? v gnd ). 2 this is also the code for an underranged analog input (v in+ ? v in? below v gnd ). sw+ msb 65,536c in + lsb comp control logic switches control busy output code cnv ref gnd in? 4c 2c c c 131,072c sw? msb 65,536c lsb 4c 2c c c 131,072c 0 6146-024 100...000 100...001 100...010 011...101 011...110 011...111 adc code (twos complement) analog input +fsr ? 1.5lsb +fsr ? 1lsb ?fsr + 1lsb ?fsr ?fsr + 0.5lsb 06146-006
data sheet ad7691 rev. d | page 15 of 28 typical connection diagram figure 29 shows an example of the recommended connection diagram for the ad7691 when multiple supplies are available. figure 29. typical application diagram with multiple supplies analog inputs figure 30 shows an equivalent circuit of the input structure of the ad7691. the two diodes, d1 and d2, provide esd protection for the analog inputs, in+ and in?. care must be taken to ensure that the analog input signal does not exceed the supply rails by more than 0.3 v because this causes the diodes to become forward biased and start conducting current. these diodes can handle a forward-biased current of 130 ma maximum. for instance, these conditions could eventually occur if the input buffer (u1) supplies are different from vdd. in such a case (for example, an input buffer with a short circuit), the current limitation can be used to protect the part. figure 30. equivalent analog input circuit the analog input structure allows the sampling of the true differential signal between in+ and in?. by using these differential inputs, signals common to both inputs are rejected. during the acquisition phase, the impedance of the analog inputs (in+ and in?) can be modeled as a parallel combination of the capacitor, c pin , and the network formed by the series connection of r in and c in . c pin is primarily the pin capacitance. r in is typically 3 k and is a lumped component composed of serial resistors and the on resistance of the switches. c in is typically 30 pf and is mainly the adc sampling capacitor. during the conversion phase, where the switches are opened, the input impedance is limited to c pin . r in and c in make a 1-pole, low-pass filter that reduces undesirable aliasing effects and limits noise. when the source impedance of the driving circuit is low, the ad7691 can be driven directly. large source impedances significantly affect the ac performance, especially total harmonic distortion (thd). the dc performances are less sensitive to the input impedance. the maximum source impedance depends on the amount of thd that can be tolerated. the thd degrades as a function of the source impedance and the maximum input frequency as shown in figure 31. figure 31. thd vs. analog input frequency and source resistance ad7691 ref gnd vdd in? in+ vio sdi sck sdo cnv 3- or 4-wire interface 5 100nf 100nf 5v 10f 2 v+ v+ v? 1.8v to vdd ref 1 0 to v ref 15 ? 2.7nf 4 v+ v? v ref to 0 15 ? 2.7nf ada4841-2 3 ada4841-2 3 4 1 see voltage reference input section for reference selection. 2 c ref is usually a 10f ceramic capacitor (x5r). 3 see table 9 for additional recommended amplifiers. 4 optional filter. see analog input section. 5 see the digital interface section for most convenient interface mode. 06146-008 c in r in d1 d2 c pin in+ or in? gnd v dd 06146-007 06146-009 frequency (khz) thd (db) 09 0 ?130 ?125 ?120 ?115 ?110 ?105 ?100 ?95 ?90 ?85 ?80 10 20 30 40 50 60 70 80 33? 100 ? 15 ? v ref = vdd 5v 250 ? 50 ?
ad7691 data sheet rev. d | page 16 of 28 driver amplifier choice although the ad7691 is easy to drive, the driver amplifier must meet the following requirements: ? the noise generated by the driver amplifier needs to be kept as low as possible to preserve the snr and transition noise performance of the ad7691 . the noise coming from the driver is filtered by the ad7691 analog input circuits 1-pole, low-pass filter made by r in and c in or by the external filter, if one is used. the snr degradation due to the amplifier is as follows: snr loss = ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2 db3 2 db3 2 )( 2 )( 2 log20 n n nadc nadc nef nef v v where: v nadc is the noise of the adc, in v, given by the following: 20 10 22 snr inpp nadc v v ? f ?3 db is the input bandwidth, in mhz, of the ad7691 (2 mhz) or the cutoff frequency of the input filter, if one is used. n is the noise gain of the amplifier (for example, 1 in buffer configuration). e n+ and e n? are the equivalent input noise voltage densities of the op amps connected to in+ and in?, in nv/hz. this approximation can be used when the resistances around the amplifier are small. if larger resistances are used, their noise contributions should also be root-sum-squared. ? for ac applications, the driver should have a thd performance commensurate with the ad7691. ? for multichannel multiplexed applications, the driver amplifier and the ad7691 analog input circuit must settle for a full-scale step onto the capacitor array at an 18-bit level (0.0004%, 4 ppm). in the amplifiers data sheet, settling at 0.1% to 0.01% is more commonly specified. this may differ significantly from the settling time at an 18-bit level and should be verified prior to driver selection. table 10. recommended driver amplifiers amplifier typical application ada4941-1 very low noise, low power single-ended-to- differential ada4841-x very low noise, small, and low power ad8655 5 v single supply, low noise ad8021 very low noise and high frequency ad8022 low noise and high frequency op184 low power, low noise, and low frequency ad8605 , ad8615 5 v single supply, low power single-to-differential driver for applications using a single-ended analog signal, either bipolar or unipolar, the ada4941-1 single-ended-to-differential driver allows for a differential input into the part. the schematic is shown in figure 32. figure 32. single-ended-to- differential driver circuit r1 and r2 set the attenuation ratio between the input range and the adc range (v ref ). r1, r2, and c f are chosen depending on the desired input resistance, signal bandwidth, antialiasing, and noise contribution. for example, for the 10 v range with a 4 k impedance, r2 = 1 k and r1 = 4 k. r3 and r4 set the common mode on the in? input, and r5 and r6 set the common mode on the in+ input of the adc. the common mode should be set close to v ref /2; however, if single supply is desired, it can be set slightly above v ref /2 to provide some headroom for the ada4941-1 output stage. for example, for the 10 v range with a single supply, r3 = 8.45 k, r4 = 11.8 k, r5 = 10.5 k, and r6 = 9.76 k. voltage reference input the ad7691 voltage reference input, ref, has a dynamic input impedance and should therefore be driven by a low impedance source with efficient decoupling between the ref and gnd pins, as explained in the layout section. when ref is driven by a very low impedance source, for example, a reference buffer using the ad8031 or the ad8605, a 10 f (x5r, 0805 size) ceramic chip capacitor is appropriate for optimum performance. if an unbuffered reference voltage is used, the decoupling value depends on the reference used. for instance, a 22 f (x5r, 1206 size) ceramic chip capacitor is appropriate for optimum performance using a low temperature drift adr43x reference. if desired, smaller reference decoupling capacitor values as low as 2.2 f can be used with a minimal impact on performance, especially dnl. regardless, there is no need for an additional lower value ceramic decoupling capacitor (for example, 100 nf) between the ref and gnd pins. ad7691 ref gnd vdd in+ 2.7nf 100nf 2.7nf in? +5v ref 10v, 5v, ... +5.2v +5.2v 15 ? 10f 15 ? r2 c f ada4941 r1 r3 100nf r5 r4 r6 06146-010
data sheet ad7691 rev. d | page 17 of 28 power supply the ad7691 uses two power supply pins: a core supply (vdd) and a digital input/output interface supply (vio). vio allows direct interface with any logic between 1.8 v and vdd. to reduce the supplies needed, the vio and vdd pins can be tied together. the ad7691 is independent of power supply sequencing between vio and vdd. additionally, it is very insensitive to power supply variations over a wide frequency range, as shown in figure 25. the ad7691 powers down automatically at the end of each conversion phase, and therefore, the power scales linearly with the sampling rate. this makes the part ideal for low sampling rate (as low as a few hertz) and low battery-powered applications. figure 33. operating current vs. sample rate supplying the adc from the reference for simplified applications, the ad7691 , with its low operating current, can be supplied directly using the reference circuit shown in figure 34. the reference line can be driven by ? the system power supply directly. ? a reference voltage with enough current output capability, such as the adr43x . ? a reference buffer, such as the ad8031 , which can also filter the system power supply, as shown in figure 34. figure 34. example of an application circuit digital interface though the ad7691 has a reduced number of pins, it offers flexibility in its serial interface modes. when in cs mode, the ad7691 is compatible with spi, qspi?, digital hosts, and dsps, for example, black fin ? adsp-bf53x or adsp-219x . in this mode, the ad7691 can use either a 3-wire or 4-wire interface. a 3-wire interface using the cnv, sck, and sdo signals minimizes wiring connections and is useful, for instance, in isolated applications. a 4-wire interface using the sdi, cnv, sck, and sdo signals allows cnv, which initiates the conversions, to be independent of the readback timing (sdi). this is useful in low jitter sampling or simultaneous sampling applications. when in chain mode, the ad7691 provides a daisy-chain feature using the sdi input for cascading multiple adcs on a single data line similar to a shift register. the mode in which the part operates depends on the sdi level when the cnv rising edge occurs. the cs mode is selected if sdi is high, and the chain mode is selected if sdi is low. the sdi hold time is such that when sdi and cnv are connected together, the chain mode is selected. in either mode, the ad7691 offers the option of forcing a start bit in front of the data bits. this start bit can be used as a busy signal indicator to interrupt the digital host and trigger the data reading. otherwise, without a busy indicator, the user must timeout the maximum conversion time prior to readback. the busy indicator feature is enabled ? in the cs mode if cnv or sdi is low when the adc conversion ends (see figure 38 and figure 42). ? in the chain mode if sck is high during the cnv rising edge (see figure 46). 1000 10 0.1 0.001 10 1m sampling rate (sps) operating current (a) 100 1k 100k 10k vdd = 5v vio 06146-045 ad8031 ad7691 vio ref vdd 10f 1f 10 ? 10k ? 5v 5v 5v 1f 1 1 optional reference buffer and filter. 06146-046
ad7691 data sheet rev. d | page 18 of 28 cs mode, 3-wire without busy indicator this mode is usually used when a single ad7691 is connected to an spi-compatible digital host. the connection diagram is shown in figure 35, and the corresponding timing is given in figure 36. with sdi tied to vio, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. once a conversion is initiated, it continues until completion irrespective of the state of cnv. this can be useful, for instance, to bring cnv low to select other spi devices, such as analog multiplexers, but cnv must be returned high before the minimum conversion time elapses and then held high for the maximum possible conversion time to avoid the generation of the busy signal indicator. when the conversion is complete, the ad7691 enters the acquisition phase and powers down. when cnv goes low, the msb is output onto sdo. the remaining data bits are clocked by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge can allow a faster reading rate, provided it has an acceptable hold time. after the 18 th sck falling edge, or when cnv goes high, whichever occurs first, sdo returns to high impedance. figure 35. 3-wire cs mode without busy indicator connection diagram (sdi high) figure 36. 3-wire cs mode without busy indicator seri al interface timing (sdi high) cnv sck sdo sdi data in clk convert v io digital host ad7691 06146-011 sdo d17 d16 d15 d1 d0 t dis sck 123 161718 t sck t sckl t sckh t hsdo t dsdo cnv conversion acquisition t conv t cyc acquisition sdi = 1 t cnvh t acq t en 06146-012
data sheet ad7691 rev. d | page 19 of 28 cs mode, 3-wire with busy indicator this mode is usually used when a single ad7691 is connected to an spi-compatible digital host having an interrupt input. the connection diagram is shown in figure 37, and the corresponding timing is given in figure 38. with sdi tied to vio, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. sdo is maintained in high impedance until the completion of the conversion irrespective of the state of cnv. prior to the minimum conversion time, cnv can be used to select other spi devices, such as analog multiplexers, but cnv must be returned low before the minimum conversion time elapses and then held low for the maximum possible conversion time to guarantee the generation of the busy signal indicator. when the conversion is complete, sdo goes from high impedance to low impedance. with a pull-up on the sdo line, this transition can be used as an interrupt signal to initiate the data reading controlled by the digital host. the ad7691 then enters the acquisition phase and powers down. the data bits are clocked out, msb first, by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge can allow a faster reading rate, provided it has an acceptable hold time. after the optional 19 th sck falling edge, or when cnv goes high, whichever occurs first, sdo returns to high impedance. if multiple ad7691 s are selected at the same time, the sdo output pin handles this contention without damage or induced latch-up. meanwhile, it is recommended to keep this contention as short as possible to limit extra power dissipation. figure 37. 3-wire cs mode with bu sy indicator connection diagram (sdi high) figure 38. 3-wire cs mode with busy indi cator serial interface timing (sdi high) data in irq clk convert vio digital host 47k ? cnv sck sdo sdi v io ad7691 06146-013 sdo d17 d16 d1 d0 t dis sck 123 171819 t sck t sckl t sckh t hsdo t dsdo cnv conversion acquisition t conv t cyc acquisition sdi = 1 t cnvh t acq 06146-014
ad7691 data sheet rev. d | page 20 of 28 cs mode, 4-wire without busy indicator this mode is usually used when multiple ad7691 s are connected to an spi-compatible digital host. a connection diagram example using two ad7691 s is shown in figure 39, and the corresponding timing is given in figure 40. with sdi high, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. in this mode, cnv must be held high during the conversion phase and the subsequent data readback. (if sdi and cnv are low, sdo is driven low.) prior to the minimum conversion time, sdi can be used to select other spi devices, such as analog multiplexers, but sdi must be returned high before the minimum conversion time elapses and then held high for the maximum possible conversion time to avoid the generation of the busy signal indicator. when the conversion is complete, the ad7691 enters the acquisition phase and powers down. each adc result can be read by bringing its sdi input low, which consequently outputs the msb onto sdo. the remaining data bits are clocked by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge allows a faster reading rate, provided it has an acceptable hold time. after the 18 th sck falling edge, or when sdi goes high, whichever occurs first, sdo returns to high impedance and another ad7691 can be read. figure 39. 4-wire cs mode without busy indicator connection diagram figure 40. 4-wire cs mode without busy indicato r serial interface timing data in clk cs1 convert cs2 digital host cnv sck sdo sdi cnv sck sdo sdi ad7691 ad7691 06146-015 sdo d17 d16 d15 d1 d0 t dis sck 123 343536 t hsdo t dsdo t en conversion acquisition t conv t cyc t acq acquisition s di (cs1) cnv t ssdicnv t hsdicnv d1 16 17 t sck t sckl t sckh d0 d17 d16 19 20 18 s di (cs2) 06146-016
data sheet ad7691 rev. d | page 21 of 28 cs mode, 4-wire with busy indicator this mode is normally used when a single ad7691 is connected to an spi-compatible digital host with an interrupt input, and it is desired to keep cnv, which is used to sample the analog input, independent of the signal used to select the data reading. this requirement is particularly important in applications where low jitter on cnv is desired. the connection diagram is shown in figure 41, and the corresponding timing is given in figure 42. with sdi high, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. in this mode, cnv must be held high during the conversion phase and the subsequent data readback. (if sdi and cnv are low, sdo is driven low.) prior to the minimum conversion time, sdi can be used to select other spi devices, such as analog multiplexers, but sdi must be returned low before the minimum conversion time elapses and then held low for the maximum possible conversion time to guarantee the generation of the busy signal indicator. when the conversion is complete, sdo goes from high impedance to low impedance. with a pull-up on the sdo line, this transition can be used as an interrupt signal to initiate the data readback controlled by the digital host. the ad7691 then enters the acquisition phase and powers down. the data bits are clocked out, msb first, by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge can allow a faster reading rate, provided it has an acceptable hold time. after the optional 19 th sck falling edge, or sdi going high, whichever occurs first, sdo returns to high impedance. figure 41. 4-wire cs mode with busy indi cator connection diagram figure 42. 4-wire cs mode with busy indicator serial interface timing data in irq clk convert cs1 vio digital host 47k? cnv sck sdo sdi ad7691 06146-017 sdo d17 d16 d1 d0 t dis sck 1 2 3 17 18 19 t sck t sckl t sckh t hsdo t dsdo t en conversion acquisition t conv t cyc t acq acquisition sdi cnv t ssdicnv t hsdicnv 06146-018
ad7691 data sheet rev. d | page 22 of 28 chain mode without busy indicator this mode can be used to daisy-chain multiple ad7691 s on a 3-wire serial interface. this feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. data readback is analogous to clocking a shift register. a connection diagram example using two ad7691 s is shown in figure 43, and the corresponding timing is given in figure 44. when sdi and cnv are low, sdo is driven low. with sck low, a rising edge on cnv initiates a conversion, selects the chain mode, and disables the busy indicator. in this mode, cnv is held high during the conversion phase and the subsequent data readback. when the conversion is complete, the msb is output onto sdo and the ad7691 enters the acquisition phase and powers down. the remaining data bits stored in the internal shift register are clocked by subsequent sck falling edges. for each adc, sdi feeds the input of the internal shift register and is clocked by the sck falling edge. each adc in the chain outputs its data msb first, and 18 n clocks are required to read back the n adcs. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge can allow a faster reading rate and, consequently, more ad7691 s in the chain, provided the digital host has an acceptable hold time. the maximum conversion rate may be reduced due to the total readback time. figure 43. chain mode without busy indicator connection diagram figure 44. chain mode without busy indicator serial interface timing clk convert data in digital host cnv sck sdo sdi cnv sck sdo sdi ad7691 b ad7691 a 06146-019 sdo a = sdi b d a 17 d a 16 d a 15 sck 1 2 3 34 35 36 t ssdisck t hsdisck t en conversion acquisition t conv t cyc t acq acquisition cnv d a 1 16 17 t sck t sckl t sckh d a 0 19 20 18 sdi a = 0 sdo b d b 17 d b 16 d b 15 d a 1 d b 1d b 0d a 17 d a 16 t hsdo t dsdo t ssckcnv t hsckcnv d a 0 06146-020
data sheet ad7691 rev. d | page 23 of 28 chain mode with busy indicator this mode can also be used to daisy-chain multiple ad7691s on a 3-wire serial interface while providing a busy indicator. this feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. data readback is analogous to clocking a shift register. a connection diagram example using three ad7691 s is shown in figure 45, and the corresponding timing is given in figure 46. when sdi and cnv are low, sdo is driven low. with sck high, a rising edge on cnv initiates a conversion, selects the chain mode, and enables the busy indicator feature. in this mode, cnv is held high during the conversion phase and the subsequent data readback. when all adcs in the chain have completed their conversions, the sdo pin of the adc closest to the digital host (see the ad7691 adc labeled c in figure 45) is driven high. this transition on sdo can be used as a busy indicator to trigger the data readback controlled by the digital host. the ad7691 then enters the acquisition phase and powers down. the data bits stored in the internal shift register are clocked out, msb first, by subsequent sck falling edges. for each adc, sdi feeds the input of the internal shift register and is clocked by the sck falling edge. each adc in the chain outputs its data msb first, and 18 n + 1 clocks are required to readback the n adcs. although the rising edge can be used to capture the data, a digital host using the sck falling edge allows a faster reading rate and, consequently, more ad7691 s in the chain, provided the digital host has an acceptable hold time. figure 45. chain mode with bu sy indicator connection diagram figure 46. chain mode with busy indicator serial interface timing clk convert data in irq digital host cnv sck sdo sdi cnv sck sdo sdi cnv sck sdo sdi ad7691 b ad7691 c ad7691 a 0 6146-021 sdo a = sdi b d a 17 d a 16 d a 15 sck 123 39 53 54 t en conversion acquisition t conv t cyc t acq acquisition cnv = sdi a d a 1 417 t sck t sckh t sckl d a 0 19 38 18 sdo b = sdi c d b 17 d b 16 d b 15 d a 1 d b 1d b 0d a 17 d a 16 55 t ssdisck t hsdisck t hsdo t dsdo sdo c d c 17 d c 16 d c 15 d a 1d a 0 d c 1d c 0d a 16 21 35 36 20 37 d b 1d b 0d a 17 d b 17 d b 16 t dsdosdi t ssckcnv t hsckcnv d a 0 t dsdosdi t dsdosdi t dsdosdi t dsdosdi 06146-022
ad7691 data sheet rev. d | page 24 of 28 application hints layout the printed circuit board that houses the ad7691 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. the pin configuration of the ad7691 , with its analog signals on the left side and its digital signals on the right side, eases this task. avoid running digital lines under the device because this couples noise onto the die unless a ground plane under the ad7691 is used as a shield. fast switching signals, such as cnv or clocks, should not run near analog signal paths. crossover of digital and analog signals should be avoided. at least one ground plane should be used. it can be common or split between the digital and analog sections. in the latter case, the planes should be joined underneath the ad7691. the ad7691 voltage reference input, ref, has a dynamic input impedance and should be decoupled with minimal parasitic inductances. this is done by placing the reference decoupling ceramic capacitor close to, ideally right up against, the ref and gnd pins and connecting them with wide, low impedance traces. finally, the power supplies, vdd and vio, of the ad7691 should be decoupled with ceramic capacitors, typically 100 nf, placed close to the ad7691 and connected using short, wide traces to provide low impedance paths and to reduce the effect of glitches on the power supply lines. an example layout following these rules is shown in figure 47 and figure 48. evaluating the ad7691 performance other recommended layouts for the ad7691 are outlined in the documentation of the evaluation board for the ad7691 ( eval-ad7691sdz ). the evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a pc via the eval-sdp-cb1z . figure 47. exampl e layout of the ad7691 (top layer) figure 48. exampl e layout of the ad7691 (bottom layer) 0 6146-023 06146-048
data sheet ad7691 rev. d | page 25 of 28 outline dimensions figure 49.10-lead mini small outline package [msop] (rm-10) dimensions shown in millimeters figure 50. 10-lead lead frame chip scale package [lfcsp_wd] 3 mm 3 mm body, very very thin, dual lead (cp-10-9) dimensions shown in millimeters ordering guide model 1, 2, 3 temperature range package description pack age option branding ordering quantity ad7691bcpzrl C40c to +85c 10-lead lfcsp_wd cp-10-9 c4e reel, 5,000 ad7691bcpzrl7 C40c to +85c 10-lead lfcsp_wd cp-10-9 c4e reel, 1,500 ad7691brmz C40c to +85c 10-lead msop rm-10 c4e tube, 50 ad7691brmz-rl7 C40c to +85c 10-lead msop rm-10 c4e reel, 1,000 eval-ad7691sdz evaluation board eval-sdp-cb1z controller board 1 z = rohs compliant part. 2 the eval-ad7691sdz can be used as a standalone evaluation board or in conjunction with the eval-sdp-cb1z for evaluation/demonstration purposes. 3 the eval-sdp-cb1z allows a pc to control and communicate with all analog devices evaluation boards ending in the sd designator. compliant to jedec standards mo-187-ba 091709-a 6 0 0.70 0.55 0.40 5 10 1 6 0.50 bsc 0.30 0.15 1.10 max 3.10 3.00 2.90 coplanarity 0.10 0.23 0.13 3.10 3.00 2.90 5.15 4.90 4.65 pin 1 identifier 15 max 0.95 0.85 0.75 0.15 0.05 2.48 2.38 2.23 0.50 0.40 0.30 10 1 6 5 0.30 0.25 0.20 pin 1 index area seating plane 0.80 0.75 0.70 1.74 1.64 1.49 0.20 ref 0.05 max 0.02 nom 0.50 bsc exposed pad 3.10 3.00 sq 2.90 p i n 1 i n d i c a t o r ( r 0 . 1 5 ) for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. coplanarity 0.08 0 2-05-2013- c top view bottom view 0.20 min
ad7691 data sheet rev. d | page 26 of 28 notes
data sheet ad7691 rev. d | page 27 of 28 notes
ad7691 data sheet rev. d | page 28 of 28 notes ?2006C2014 analog devices, inc. all ri ghts reserved. trademarks and registered trademarks are the prop erty of their respective owners. d06146-0-7/14(d)


▲Up To Search▲   

 
Price & Availability of AD7691-15

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X