View AUIRS20162S_8212847.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AUIRS20162S 1 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 automotive grade features ? leadfree, rohs compliant ? automotive qualified ? one high side output and internal low side vs recharge. ? cmos schmitt trigger inverted input with pull up resistor ? cmos schmitt trigger inverted reset with pull down resistor ? 5v compatible logic level inputs ? immune to C vs s pike and tolerant to dvs/dt typical applications ? common rail injections ? diesel/gasoline direct injections ? solenoid drivers ? actuators and brushed dc motors product summary topology low side input, high side driver with vs recharge v offset 150 v v out 4.4 v C 20 v i o+ & i o - (typical) 0.25 a t on & t off (typical) 150 ns deadtime dt on / dt off (typical) 70ns / 6 us package options 8 - lead soic auirs20162 s typical connection diagram orderable part number package type standard pack note form quantity AUIRS20162S(tr) soic8 tape and reel 25 00 5 v a u i r s 2 0 1 6 2 s v c c n c v b h o n c v s r e s e t - 7 v l o g i c l e v e l r e s e t i n - g n d l o g i c l e v e l i n p u t c v c c c b s
AUIRS20162S 2 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 absolute maxim um ratings absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. these are stress ratings only, functional operation of the device at these or any other condition beyond those indicated in the recommended operati ng condition is not implied. exposure to absolute maximum - rated conditions for extended periods may affect device reliability. all voltage parameters are absolute voltages referenced to gnd unless otherwise stated in the table. the thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. symbol definition min. max. units v bs high side floating supply voltage - 0.3 20 v v b high side driver output stage voltage, neg. transient: 0.5 ms, external mosfet off - 5.0 166 v v s high side floating supply offset voltage neg. transient 0.4 s - 8.0 150 v v ho output voltage gate connection v s C 0.3 v b + 0.3 v v cc supply voltage - 0.3 20 v v in input voltage - 0.3 v cc + 0.3 v i in input injection current. full function, no latch - up; (guaranteed by design) . test at 5v and 7v on eng. samples. --- +1 ma v res reset input voltage - 0.3 v cc + 0.3 v dv/dt allowable offset voltage slew rate - 50 50 v/nsec rth ja thermal resistance, junction to ambient - 200 c/w t j junction tem perature - 55 150 oc t s storage temperature - 55 150 oc recommended operating conditions for proper operations the device should be used within the recommended conditions. symbol definition min. max. units v b ? high side driver output stage voltage v s + 4.4 v s +20 v v s high side floating supply offset voltage - 3 150 v v h o output gate voltage v s v b v v cc ???? supply voltage 4.4 6.5 v v in input voltage 0 v cc v v res reset input voltage 0 v cc v ta ambient temperature - 40 125 oc f s switching frequ ency ?? ( load: 50 ohm , 2.5nf into v s ) --- 200 khz t inlow _ min minimum low input width ??? 1000 --- ns t in high _ m in minimum high input width ??? 60 --- ns ? reset - logic functional for v bs > 2v ?? duty cycle = 0.5, v bs = 7 v ??? guaranteed b y desi gn. pulse width below the specified values may be ignored. output will either follow the input or will ignore it. no false output state is guaranteed when minimum input width is smaller than t in . ???? lo gic operation functional for vcc > 2 .7 v , see also tab le t able 1 on page 10 .
AUIRS20162S 3 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 electrical characteristics unless otherwise specified, v cc = 5v, v bs = 7v, v s = 0v, in = 0v, res = 5v, load r = 50 ? , c = 2.5nf. unless otherwise noted, these specifications apply for an operating junction temperature range of - 40 ? c ? tj ? 125 ? c. symbol definition min typ max units test conditions vcc supply characteristics v ccuv + v cc supply undervoltage positive going threshold 4.3 v v cc rising from 0v v ccuv - v cc supply undervoltage negative going threshold 2.8 v cc dropp ing from 5v v ccuvhys v cc supply undervoltage lockout hysteresis 0.02 0.3 0.60 t d uvcc undervoltage lockout response time 0.5 20 ? cc steps either from 6.5v to 2.7v or from 2.7v to 6.5v i qcc v cc supply current 400 ua v cc = 3.6v & 6.5v v bs sup ply characteristics v bsuv + v bs supply undervoltage positive going threshold 5.4 v v bs rising from 0v v bsuv - v bs supply undervoltage negative going threshold 3.9 v bs dropping from 5v v bsuvhys v bs supply undervoltage lockout hysteresis 0.02 0.3 0.60 t d uvbs undervoltage lockout response time 0.5 20 ? bs steps either from 6.5v to 2.7v or from 2.7v to 6.5v i qbs1 v bs supply current 130 ? bs = 7v, in = 0v or 5v i qbs2 v bs supply current 300 ? bs = 16v, in = 0v o r 5v ? bs ? bs drop due to output turn - on 210 mv v bs = 7v, c b s = 1 ? d _ igen - in = 3 ? test = 100 ? ? see also fig. 4 and 5
AUIRS20162S 4 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 electrical characteristics unless otherwise specified, v cc = 5v, v bs = 7v, v s = 0v, in = 0v, res = 5v, load r = 50 ? , c = 2.5nf . unless otherwise noted, these specifications apply for an operating junction temperature range of - 40 ? c ? tj ? 125 ? c. symbol definition min typ max units test conditions gate driver characteristics i pkso1 peak output source current 12 0 250 ma tj = 25 ? ?? pkso2 peak output source current 70 ma ?? i pkso3 peak output source current 250 500 ma v bs = 16v, tj = 25 ? ?? pkso4 peak output source current 150 ma v bs = 16v ?? r1 output rise time 0.2 0.4 ? ? r2 output ri se time 0.5 ? t r3 output rise time 0.1 0.2 ? bs = 16v, tj = 25 ? r4 output rise time 0.3 ? bs = 16v i pksi1 peak output sink current 120 250 ma in = 5v, tj = 25 ? ?? pksi2 peak output sink current 70 ma in = 5v, ?? pksi3 peak outp ut sink current 250 500 ma v bs = 16v, in = 5v, tj = 25 ? ?? pksi4 peak output sink current 150 ma v bs = 16v, in = 5v ?? f1 output fall time 0.2 0.4 ? ? f2 output fall time 0.5 ? f3 output fall time 0.1 0.2 ? bs = 16v, in = 5v, tj = 25 ? f4 output fall time 0.3 ? bs = 16v, in = 5v t plh input - to - output turn - on propagation delay (50% input level to 10% output level) 0.15 0.35 ? phl input - to - output turn - off propagation delay (50% input level to 90 % output level) 0.15 0.35 ? phl_res res - to - output turn - off propagation delay (50% input level to 90% [t phl ] output levels) 0.15 0.35 ? plh_res res - to - output turn - on propagation delay (50% input level to 10% [t plh ] output levels) 0.15 0.35 ? ?? : peak output sink and source current tests are performed with the output shorted and therefore highly dissipative. therefore, it is not recommended that this test be performed for longer than 10usec at a time.
AUIRS20162S 5 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 electrical characteristics unless otherwise specified, v cc = 5v, v bs = 7v, v s = 0v, in = 0v, res = 5v, load r = 50 ? , c = 2.5nf. unless otherwise noted, these specifications apply for an operating junction temperature range of - 40 ? c ? tj ? 125 ? c. symbol definition min typ max units test c onditions input characteristics v inh high logic level input threshold 0.6 6 * vcc v v cc =5v v inl low logic level input threshold 0.28* vcc v v cc =5v r in in pull up input resistance 60 100 220 k ? in high logic level input current 5 ? in = v cc v h_res high logic level res input threshold 0.6 6 * vcc v v cc =5v v l_res low logic level res input threshold 0.28* vcc v v cc =5v r res res pull down input resistance 60 100 220 k ? res low logic level input current 5 ? res =0 recharge characte ristics t on_rech recharge transistor turn - on propagation delay 3 6 9 ? s = 5v t off_rech recharge transistor turn - off propagation delay 0.08 0.2 4 ? rech recharge output transistor on - state voltage drop 1.2 v i s = 1ma, in = 5v. deadtime cha racteristics dt hoff high side turn - off to recharge gate turn - on 3 6 9 ? cc = 5v, v bs = 7v dt hon recharge gate turn - off to high side turn - on 0.0 05 0.07 0.4 ? cc = 5v, v bs = 7v
AUIRS20162S 6 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 functional block diagram
AUIRS20162S 7 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 i nput/output pin equivalent circuit diagrams v c c g n d i n - e s d d i o d e e s d d i o d e r e s d v c c g n d r e s e t - e s d d i o d e e s d d i o d e r e s d v b v s h o e s d d i o d e e s d d i o d e g n d g n d v c c 2 0 v v s v b 2 0 v g n d v b 1 6 6 v
AUIRS20162S 8 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 lead definitions pin number symbol pin description 1 v cc driver supply, typically 5.0v 2 in - driver control signal input (negative logic) 3 gnd ground 4 reset - driver enable signal input (negative logic) 5 v s mosfet source connection 6 nc no connection (no bond - wire) 7 ho mosfet gate connection 8 v b driver output stage supply lead assignment s 8 l e a d s o i c 8 7 6 5 v c c v b i n - 1 2 3 4 h o v s g n d r e s e t - n c
AUIRS20162S 9 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 application information and additional details the auirs2016 2s is a high voltage power mosfet and igbt high side driver with internal vs - to - gnd recharge nmos. proprietary hvic and latch immune cmos technologies enable ruggedized monolithic construction. the logic input is compatible with standard 5v cmos or lsttl logic. the output driver features a 250ma high pulse current buffer stage. the channel can be used to drive an n - chan nel power mosfet or igbt in the high side configuration, which operates up to 150 volts above gnd ground. a truth table for v cc , v bs , reset, in, h o and rechfet is shown as follows. this table is valid for voltages ranges defined in the recommended operat ing conditions section. s upply voltages and thresholds signals output ho recharge path v cc v bs reset - in - < v ccuv - x x x off on > v ccuv + x low x off on > v ccuv+ x x high off on > v ccuv+ > v bsuv+ high low on off > v ccuv+ < v bsuv - high low off off table 1: logic operation rech arge path = on indicates that the recharge mosfet is on. rech arge path = off indicates that the recharge mosfet is off. in the case that vcc will be removed during operation, ho will be turned off if the resulting dvcc/dt is slow enough to allow uvlo response time as defined in the td uvcc parameter. if ho was low it will remain low.
AUIRS20162S 10 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 timing diagrams and additional information input / output figure 1 : input/output timing diagram reset figure 2 : reset timing diagram start - up figure 3 : start up diagram i n r e s h o r e c h a r g e o f f o n t o f f _ r e c h 1 0 % 9 0 % 9 0 % 1 0 % t p h l t p l h t o n _ r e c h t r t f i n r e s h o t p l h _ r e s t p h l _ r e s i n ( l o g i c 0 , p u l l d o w n t o g n d ) r e s ( l o g i c 1 , p u l l u p t o v c c ) h o v c c v b s v c c u v l o 2 . 7 v t d u v c c v b s u v t d u v b s
AUIRS20162S 11 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 vb drop voltage test figure 4 : vbs drop voltage test vbs voltage drop due to the high side section activation at no lo ad figure 5 : vbs drop voltage waveforms
AUIRS20162S 12 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 performance graphs reset functionality graph: figure 6 - 1 figure 6. reset functionality: this graph explains the functionality limitation as a function of v cc , v bs and temperature. for each parti cular temperature and v cc , the output is non - functional for any value of v bs above the drawn curve. but for any value of v bs below the curve the functionality is fine. reset functional diagram: figure 6 - 2 in - reset - ho - v s reset functionality graph 5 7 9 11 13 15 17 19 21 23 25 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 vcc (v) vbs (v) 25c -40c 125c
AUIRS20162S 13 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 parameter temperature trends fi gures illustrated in this chapter provide information on the experimental performance of the auirs2 016 2 s hvic. the line plotted in each figure is generated from actual lab data. a large number of individual samples were tested at three temperatures ( - 40 oc , 25 oc, and 125 oc) in order to g enerate the experimental curve. the line consist s of three data points (one data point at each of the tested temperatures) that have been connected together to illustrate the understood trend. the individual data points on the typ. curve were determined by calculating the averaged experimental value of the parameter (for a given temperature). input and reset thresholds : figure 7 - 1: positive input and reset threshold voltage distribution curves figure 7 - 2: ne gative input and reset thre shold voltage distribution curves vinth+ vs vcc supply 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 5 6.5 vcc (v) (v) -40c 27c 125c vinth- vs vcc supply 1.6 1.8 2 2.2 2.4 2.6 2.8 3 5 6.5 vcc (v) (v) -40c 27c 125c
AUIRS20162S 14 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 v buv undervoltage shutdown threshold v b : figure 8 - 1: negative going vbsuv - value vs. temperature: figure 8 - 2: positive going vbsuv+ value vs. temperature 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 -50 -25 0 25 50 75 100 125 150 -3std mean +3std 4.40 4.50 4.60 4.70 4.80 4.90 5.00 5.10 -50 -25 0 25 50 75 100 125 150 -3std mean +3std
AUIRS20162S 15 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 input and reset impedance figure 9: input and reset impedance distribution curves vs. temperature recharge fet i - v curve figure 10: recharge fet iv - curve input and reset impedance 0 20 40 60 80 100 120 140 160 180 200 -42 -22 -2 18 38 58 78 98 118 mean +3std -3std v_rech fet i-v curve 0 0.5 1 1.5 2 2.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 v_rech (v) i_current (ma) -40c 27c 125c
AUIRS20162S 16 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 package details: soic8
AUIRS20162S 17 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 tape and reel details: soic8 carrier tape dimension for 8soicn code min max min max a 7.90 8.10 0.311 0.318 b 3.90 4.10 0.153 0.161 c 11.70 12.30 0.46 0.484 d 5.45 5.55 0.214 0.218 e 6.30 6.50 0.248 0.255 f 5.10 5.30 0.200 0.208 g 1.50 n/a 0.059 n/a h 1.50 1.60 0.059 0.062 reel dimensions for 8soicn code min max min max a 329.60 330.25 12.976 13.001 b 20.95 21.45 0.824 0.844 c 12.80 13.20 0.503 0.519 d 1.95 2.45 0.767 0.096 e 98.00 102.00 3.858 4.015 f n/a 18.40 n/a 0.724 g 14.50 17.10 0.570 0.673 h 12.40 14.40 0.488 0.566 metric imperial metric imperial e f a c d g a b h note : controlling dimension in mm loaded tape feed direction a h f e g d b c
AUIRS20162S 18 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 part marking i nformation a s 2 0 1 6 2 i r l o g o a y w w ? p a r t n u m b e r d a t e c o d e p i n 1 i d e n t i f i e r l o t c o d e ( p r o d m o d e C 4 d i g i t s p n c o d e ) a s s e m b l y s i t e c o d e p e r s c o p 2 0 0 - 0 0 2 ? x x x x m a r k i n g c o d e l e a d f r e e r e l e a s e d n o n - l e a d f r e e r e l e a s e d ? p
AUIRS20162S 19 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 qualification information (note1) qualification level automotive (per aec - q100) comments: this family of ics has passed an automotive qualification. irs industrial and consumer qualification level is gran ted by extension of the higher automotive level. moisture sensitivity level soic 8n msl 3 260c (note2) (per ipc/jedec j - std - 020) esd machine model class m1 ( pass +/ - 20 0 v ) (per aec - q100 - 003) human body model class h 1c (+/ - 2000v) ( per aec - q100 - 002 ) cha rged device model class c4 ( pass +/ - 1000 v ) (per aec - q100 - 011) ic latch - up test class ii , level a (per aec - q100 - 004) rohs compliant yes note 1 qualification standards can be found at international rectifiers web site http://www.irf.com/ note 2 higher msl ratings may be available for the specific package types listed here. please contact your international rectifier sales representative for further information.
AUIRS20162S 20 www.irf.com ? 2014 international rectifier submit datasheet feedback dec ember 10 , 2014 important notice unless specifically designated for the automotive market, international rectifier corporation and its subsidiaries (ir) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any produc t or services without notice. part numbers designated with the au prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. all products are sold subject to irs term s and conditions of sale supplied at the time of order acknowledgment. ir warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with irs standard warranty. testing and other quality control tech niques are used to the extent ir deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ir assumes no liability for applications assistance or c ustomer product design. customers are responsible for their products and applications using ir components. to minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. reproduction of ir information in ir data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alterations is an unfair an d deceptive business practice. ir is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ir products or serviced with statements different from or beyond the paramet ers stated by ir for that product or service voids all express and any implied warranties for the associated ir product or service and is an unfair and deceptive business practice. ir is not responsible or liable for any such statements. ir products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the i r product could creat e a situation where personal injury or death may occur. should buyer purchase or use ir products for any such unintended or unauthorized application, buyer shall indemnify and hold international rectifier and its officers, employees, subsidiaries, affilia tes, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such cl aim alleges that ir was negligent regarding the design or manufacture of the product. ir products are neither designed nor intended for use in military/aerospace applications or environments unless the ir products are specifically designated by ir as mili tary - grade or enhanced plastic. only products designated by ir as military - grade meet military specifications. buyers acknowledge and agree that any such use of ir products which ir has not designated as military - grade is solely at the buyers risk, an d that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. ir products are neither designed nor intended for use in automotive applications or environments unless the specific ir products are designated by ir as compliant with iso/ts 16949 requirements and bear a part number including the designation au. buyers acknowledge and agree that, if they use any non - designated products in automotive applications, ir will not be responsible for any f ailure to meet such requirements. for technical support, please contact irs technical assistance center http://www.irf.com/technical - info/ world headquarters: 101 n. sepulveda blvd. , el segundo, cal ifornia 90245 tel: (310) 252 - 7105

▲Up To Search▲

Price & Availability of AUIRS20162S

	To Download AUIRS20162S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .