View B32671Z6683_8033824.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

film capacitors metallized polypropylene film capacitors (mkp) series/type: b32671z ... b32673z date: december 2012 ? epcos ag 2012. reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without epcos' prior express consent is prohibited.
typical applications pfc (power factor correction) not suitable for "across the line" applications climatic max. operating temperature: 125 c climatic category (iec 60068-1): 55/110/56 construction dielectric: metallized polypropylene (pp) wound capacitor technology plastic case (ul 94 v-0) epoxy resin sealing, flame retardant features high frequency capability very small dimensions rohs-compatible halogen-free capacitors available on request terminals parallel wire leads, lead-free tinned marking manufacturer's logo, rated capacitance (coded), tolerance, rated dc voltage, type number delivery mode bulk (untaped) taped (ammo pack or reel) for notes on taping, refer to chapter "taping and packing?. dimensional drawing dimensions in mm lead spacing 0.4 lead diameter d 1 type 10 0.6 b32671z 15 0.8 b32672z 22.5 0.8 b32673z metallized polypropylene film capacitors (mkp) b32671z ... b32673z power factor correction page 2 of 20 please read cautions and warnings and important notes at the end of this document.
overview of available types lead spacing 10 mm 15 mm 22.5 mm type b32671z b32672z b32673z page 4 5 6 v rms (v ac) 310 220 277 310 220 277 310 v r (v dc) 630 450 520 630 450 520 630 c r ( m f) 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.12 0.15 0.22 0.33 0.47 0.56 0.68 1.0 1.2 1.5 2.2 b32671z ... b32673z power factor correction page 3 of 20 please read cautions and warnings and important notes at the end of this document.
ordering codes and packing units (lead spacing 10 mm) v rms f 1 khz v ac v r v dc c r m f max. dimensions w h l mm ordering code (composition see below) ammo pack pcs./moq reel pcs./moq untaped pcs./moq moq = minimum order quantity, consisting of 4 packing units. further e series and intermediate capacitance values on request. composition of ordering code + = capacitance tolerance code: *** = packaging code: k = 10% j = 5% 289 = ammo pack 189 = reel 000 = untaped (lead length 6 1 mm) 310 630 0.010 4.0 9.0 13.0 b32671z6103+*** 4000 6800 4000 0.015 4.0 9.0 13.0 b32671z6153+*** 4000 6800 4000 0.022 4.0 9.0 13.0 b32671z6223+*** 4000 6800 4000 0.033 5.0 11.0 13.0 b32671z6333+*** 3320 5200 4000 0.047 5.0 11.0 13.0 b32671z6473+*** 3320 5200 4000 0.068 6.0 12.0 13.0 B32671Z6683+*** 2720 4400 4000 0.10 6.0 12.0 13.0 b32671z6104+*** 2720 4400 4000 b32671z power factor correction page 4 of 20 please read cautions and warnings and important notes at the end of this document.
ordering codes and packing units (lead spacing 15 mm) v rms f 1 khz v ac v r v dc c r m f max. dimensions w h l mm ordering code (composition see below) ammo pack pcs./moq reel pcs./moq untaped pcs./moq moq = minimum order quantity, consisting of 4 packing units. further e series and intermediate capacitance values on request. composition of ordering code + = capacitance tolerance code: *** = packaging code: k = 10% j = 5% 289 = ammo pack 189 = reel 000 = untaped (lead length 6 1 mm) 220 450 0.10 5.0 10.5 18.0 b32672z4104+*** 4680 5200 4000 0.15 5.0 10.5 18.0 b32672z4154+*** 4680 5200 4000 0.22 6.0 11.0 18.0 b32672z4224+*** 3840 4400 4000 0.33 7.0 12.5 18.0 b32672z4334+*** 3320 3600 4000 0.47 8.0 14.0 18.0 b32672z4474+*** 2920 3000 2000 0.68 9.0 17.5 18.0 b32672z4684+*** 2560 2800 2000 1.0 11.0 18.5 18.0 b32672z4105k*** 2200 1200 277 520 0.047 5.0 10.5 18.0 b32672z5473+*** 4680 5200 4000 0.10 6.0 11.0 18.0 b32672z5104+*** 3840 4400 4000 0.15 6.0 11.0 18.0 b32672z5154+*** 3840 4400 4000 0.22 7.0 12.5 18.0 b32672z5224+*** 3320 3600 4000 0.33 8.5 14.5 18.0 b32672z5334+*** 2720 2800 2000 0.47 9.0 17.5 18.0 b32672z5474+*** 2560 2800 2000 0.68 11.0 18.5 18.0 b32672z5684+*** 2000 1200 1.0 11.0 18.5 18.0 b32672z5105k*** 2200 1200 310 630 0.033 5.0 10.5 18.0 b32672z6333+*** 4680 5200 4000 0.047 5.0 10.5 18.0 b32672z6473+*** 4680 5200 4000 0.068 5.0 10.5 18.0 b32672z6683+*** 4680 5200 4000 0.10 6.0 11.0 18.0 b32672z6104+*** 3840 4400 4000 0.12 6.0 11.0 18.0 b32672z6124+*** 3840 4400 4000 0.15 6.0 12.0 18.0 b32672z6154+*** 3840 4400 4000 0.33 8.5 14.5 18.0 b32672y6334k*** 2720 2800 2000 0.33 9.0 17.5 18.0 b32672z6334+*** 2560 2800 2000 0.47 11.0 18.5 18.0 b32672z6474+*** 2200 1200 0.56 11.0 18.5 18.0 b32672z6564+*** 2200 1200 b32672z power factor correction page 5 of 20 please read cautions and warnings and important notes at the end of this document.
ordering codes and packing units (lead spacing 22.5 mm) v rms f 1 khz v ac v r v dc c r m f max. dimensions w h l mm ordering code (composition see below) ammo pack pcs./moq reel pcs./moq untaped pcs./moq moq = minimum order quantity, consisting of 4 packing units. further e series and intermediate capacitance values on request. composition of ordering code + = capacitance tolerance code: *** = packaging code: k = 10% j = 5% 289 = ammo pack 189 = reel 000 = untaped (lead length 6 1 mm) 220 450 0.22 6.0 15.0 26.5 b32673z4224+*** 2720 2800 2880 0.22 7.5 14.0 26.5 b32673t4224k*** 2200 2000 2280 0.33 6.0 15.0 26.5 b32673z4334+*** 2720 2800 2880 0.33 7.5 14.0 26.5 b32673t4334k*** 2200 2000 2280 0.47 6.0 15.0 26.5 b32673z4474+*** 2720 2800 2880 0.47 7.5 14.0 26.5 b32673t4474k*** 2200 2000 2280 0.68 7.0 16.0 26.5 b32673z4684+*** 2320 2400 2520 0.68 7.5 14.0 26.5 b32673t4684k*** 2200 2000 2280 1.0 10.5 16.5 26.5 b32673z4105+*** 1560 1600 2160 1.5 11.0 20.5 26.5 b32673z4155+*** 1480 1400 2040 2.2 12.0 22.0 26.5 b32673z4225+*** 1800 277 520 0.22 6.0 15.0 26.5 b32673z5224+*** 2720 2800 2880 0.22 7.5 14.0 26.5 b32673t5224k*** 2200 2000 2280 0.33 6.0 15.0 26.5 b32673z5334+*** 2720 2800 2880 0.33 7.5 14.0 26.5 b32673t5334k*** 2200 2000 2280 0.47 7.0 16.0 26.5 b32673z5474+*** 2320 2400 2520 0.47 7.5 14.0 26.5 b32673t5474k*** 2200 2000 2280 0.68 10.5 16.5 26.5 b32673z5684+*** 1560 1600 2160 1.0 10.5 20.5 26.5 b32673z5105+*** 2160 1.5 12.0 22.0 26.5 b32673z5155+*** 1800 310 630 0.15 6.0 15.0 26.5 b32673z6154+*** 2720 2800 2880 0.22 6.0 15.0 26.5 b32673z6224+*** 2720 2800 2880 0.33 7.0 16.0 26.5 b32673z6334+*** 2820 2400 2520 0.33 7.5 14.0 26.5 b32673t6334+*** 2200 2000 2280 0.47 8.5 16.5 26.5 b32673z6474+*** 1920 2000 2040 0.68 10.5 18.5 26.5 b32673z6684+*** 1560 1600 2160 1.0 11.0 20.5 26.5 b32673z6105+*** 1480 1400 2040 1.2 12.0 22.0 26.5 b32673z6125+*** 1800 1.5 14.5 29.5 26.5 b32673z6155+*** 2160 2.2 14.5 29.5 26.5 b32673z6225+*** 2160 b32673z power factor correction page 6 of 20 please read cautions and warnings and important notes at the end of this document.
technical data max. operating temperature t op,max +125 c dissipation factor tan d (in 10 -3) at 20 c (upper limit values) c r 0.1 f 0.1 f< c r at 1 khz 100 khz 1 (typically 0.6) 5.0 1.0 insulation resistance r ins or time constant t = c r r ins at 20 c, rel. humidity 65% (minimum as-delivered values) > 30 000 m w > 10 000 s (c r 0.33 f) (c r > 0.33 f) total self-inductance l (lead length 3mm) ls 15 mm ls 22.5 mm 10 nh 18 nh dc test voltage 1.6 v r , 2 s category voltage v c (continuous operation with v dc or v ac at f 1 khz) t a ( c) dc voltage derating ac voltage derating t a 85 85 failure criteria: total failure short circuit or open circuit failure due to variation of parameters capacitance change d c/c dissipation factor tan d insulation resistance r ins > 10% > 4 upper limit values < 1500 m w pulse handling capability "dv/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in v/ m s. "k 0 " represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in v 2 / m s. note: the values of dv/dt and k 0 provided below must not be exceeded in order to avoid damaging the capacitor. dv/dt values lead spacing 10 mm 15 mm 22.5 mm v r v rms v dc v ac dv/dt in v/ m s 450 220 160 100 520 277 200 120 630 310 400 250 160 k 0 values lead spacing 10 mm 15 mm 22.5 mm v r v rms v dc v ac k 0 in v 2 / m s 450 220 128 000 80 000 520 277 208 000 125 000 630 310 504 000 504 000 202 000 b32671z ... b32673z power factor correction page 8 of 20 please read cautions and warnings and important notes at the end of this document.
permissible ac voltage v rms versus frequency f (for sinusoidal waveforms t a 90 c) for t a >90 c, please refer to "general technical information", section 3.2.3. lead spacing 10 mm 630 v dc/310 v ac b32671z power factor correction page 9 of 20 please read cautions and warnings and important notes at the end of this document.
permissible ac voltage v rms versus frequency f (for sinusoidal waveforms t a 100 c) for t a >100 c, please refer to "general technical information", section 3.2.3. lead spacing 15 mm 450 v dc/220 v ac 520 v dc/277 v ac 630 v dc/310 v ac b32672z power factor correction page 10 of 20 please read cautions and warnings and important notes at the end of this document.
permissible ac voltage v rms versus frequency f (for sinusoidal waveforms t a 100 c) for t a >100 c, please refer to "general technical information", section 3.2.3. lead spacing 22.5 mm 450 v dc/220 v ac 520 v dc/277 v ac 630 v dc/310 v ac b32673z power factor correction page 11 of 20 please read cautions and warnings and important notes at the end of this document.
mounting guidelines 1 soldering 1.1 solderability of leads the solderability of terminal leads is tested to iec 60068-2-20, test ta, method 1. before a solderability test is carried out, terminals are subjected to accelerated ageing (to iec 60068-2-2, test ba: 4 h exposure to dry heat at 155 c). since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. solder bath temperature 235 5 c soldering time 2.0 0.5 s immersion depth 2.0 +0/ 0.5 mm from capacitor body or seating plane evaluation criteria: visual inspection wetting of wire surface by new solder 3 90%, free-flowing solder 1.2 resistance to soldering heat resistance to soldering heat is tested to iec 60068-2-20, test tb, method 1a. conditions: series solder bath temperature soldering time mkt boxed (except 2.5 6.5 7.2 mm) coated uncoated (lead spacing > 10 mm) 260 5 c 10 1 s mfp mkp (lead spacing > 7.5 mm) mkt boxed (case 2.5 6.5 7.2 mm) 5 1 s mkp mkt (lead spacing 7.5 mm) uncoated (lead spacing 10 mm) insulated (b32559) < 4 s recommended soldering profile for mkt uncoated (lead spacing 10 mm) and insulated (b32559) b32671z ... b32673z power factor correction page 12 of 20 please read cautions and warnings and important notes at the end of this document.
immersion depth 2.0 +0/ 0.5 mm from capacitor body or seating plane shield heat-absorbing board, (1.5 0.5) mm thick, between capacitor body and liquid solder evaluation criteria: visual inspection no visible damage d c/c 0 2% for mkt/mkp/mfp 5% for emi suppression capacitors tan d as specified in sectional specification b32671z ... b32673z power factor correction page 13 of 20 please read cautions and warnings and important notes at the end of this document.
1.3 general notes on soldering permissible heat exposure loads on film capacitors are primarily characterized by the upper cate- gory temperature t max . long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics. for short exposures (as in practical soldering processes) the heat load (and thus the possible effects on a capacitor) will also depend on other factors like: pre-heating temperature and time forced cooling immediately after soldering terminal characteristics: diameter, length, thermal resistance, special configurations (e.g. crimping) height of capacitor above solder bath shadowing by neighboring components additional heating due to heat dissipation by neighboring components use of solder-resist coatings the overheating associated with some of these factors can usually be reduced by suitable coun- termeasures. for example, if a pre-heating step cannot be avoided, an additional or reinforced cooling process may possibly have to be included. epcos recommends the following conditions: pre-heating with a maximum temperature of 110 c temperature inside the capacitor should not exceed the following limits: mkp/mfp 110 c mkt 160 c when smd components are used together with leaded ones, the leaded film capacitors should not pass into the smd adhesive curing oven. the leaded components should be assembled af- ter the smd curing step. leaded film capacitors are not suitable for reflow soldering. uncoated capacitors for uncoated mkt capacitors with lead spacings 10 mm (b32560/b32561) the following mea- sures are recommended: pre-heating to not more than 110 c in the preheater phase rapid cooling after soldering b32671z ... b32673z power factor correction page 14 of 20 please read cautions and warnings and important notes at the end of this document.
cautions and warnings do not exceed the upper category temperature (uct). do not apply any mechanical stress to the capacitor terminals. avoid any compressive, tensile or flexural stress. do not move the capacitor after it has been soldered to the pc board. do not pick up the pc board by the soldered capacitor. do not place the capacitor on a pc board whose pth hole spacing differs from the specified lead spacing. do not exceed the specified time or temperature limits during soldering. avoid external energy inputs, such as fire or electricity. avoid overload of the capacitors. the table below summarizes the safety instructions that must always be observed. a detailed de- scription can be found in the relevant sections of the chapters "general technical information" and "mounting guidelines". topic safety information reference chapter "general technical information" storage conditions make sure that capacitors are stored within the specified range of time, temperature and humidity conditions. 4.5 "storage conditions" flammability avoid external energy, such as fire or electricity (passive flammability), avoid overload of the capacitors (active flammability) and consider the flammability of materials. 5.3 "flammability" resistance to vibration do not exceed the tested ability to withstand vibration. the capacitors are tested to iec 60068-2-6. epcos offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. consult our catalog "film capacitors for automotive electronics". 5.2 "resistance to vibration" b32671z ... b32673z power factor correction page 15 of 20 please read cautions and warnings and important notes at the end of this document.
topic safety information reference chapter "mounting guidelines" soldering do not exceed the specified time or temperature limits during soldering. 1 "soldering" cleaning use only suitable solvents for cleaning capacitors. 2 "cleaning" embedding of capacitors in finished assemblies when embedding finished circuit assemblies in plastic resins, chemical and thermal influences must be taken into account. caution: consult us first, if you also wish to embed other uncoated component types! 3 "embedding of capacitors in finished assemblies" b32671z ... b32673z power factor correction page 16 of 20 please read cautions and warnings and important notes at the end of this document.
symbols and terms symbol english german a heat transfer coefficient w?rmebergangszahl a c temperature coefficient of capacitance temperaturkoeffizient der kapazit?t a capacitor surface area kondensatoroberfl?che b c humidity coefficient of capacitance feuchtekoeffizient der kapazit?t c capacitance kapazit?t c r rated capacitance nennkapazit?t d c absolute capacitance change absolute kapazit?ts?nderung d c/c relative capacitance change (relative deviation of actual value) relative kapazit?ts?nderung (relative abweichung vom ist-wert) d c/c r capacitance tolerance (relative deviation from rated capacitance) kapazit?tstoleranz (relative abweichung vom nennwert) dt time differential differentielle zeit d t time interval zeitintervall d t absolute temperature change (self-heating) absolute temperatur?nderung (selbsterw?rmung) d tan d absolute change of dissipation factor absolute ?nderung des verlustfaktors d v absolute voltage change absolute spannungs?nderung dv/dt time differential of voltage function (rate of voltage rise) differentielle spannungs?nderung (spannungsflankensteilheit) d v/ d t voltage change per time interval spannungs?nderung pro zeitintervall e activation energy for diffusion aktivierungsenergie zur diffusion esl self-inductance eigeninduktivit?t esr equivalent series resistance ersatz-serienwiderstand f frequency frequenz f 1 frequency limit for reducing permissible ac voltage due to thermal limits grenzfrequenz fr thermisch bedingte reduzierung der zul?ssigen wechselspannung f 2 frequency limit for reducing permissible ac voltage due to current limit grenzfrequenz fr strombedingte reduzierung der zul?ssigen wechselspannung f r resonant frequency resonanzfrequenz f d thermal acceleration factor for diffusion therm. beschleunigungsfaktor zur diffusion f t derating factor deratingfaktor i current (peak) stromspitze i c category current (max. continuous current) kategoriestrom (max. dauerstrom) b32671z ... b32673z power factor correction page 17 of 20 please read cautions and warnings and important notes at the end of this document.
symbol english german i rms (sinusoidal) alternating current, root-mean-square value (sinusf?rmiger) wechselstrom i z capacitance drift inkonstanz der kapazit?t k 0 pulse characteristic impulskennwert l s series inductance serieninduktivit?t l failure rate ausfallrate l 0 constant failure rate during useful service life konstante ausfallrate in der nutzungsphase l test failure rate, determined by tests experimentell ermittelte ausfallrate p diss dissipated power abgegebene verlustleistung p gen generated power erzeugte verlustleistung q heat energy w?rmeenergie r density of water vapor in air dichte von wasserdampf in luft r universal molar constant for gases allg. molarkonstante fr gas r ohmic resistance of discharge circuit ohmscher widerstand des entladekreises r i internal resistance innenwiderstand r ins insulation resistance isolationswiderstand r p parallel resistance parallelwiderstand r s series resistance serienwiderstand s severity (humidity test) sch?rfegrad (feuchtetest) t time zeit t temperature temperatur t time constant zeitkonstante tan d dissipation factor verlustfaktor tan d d dielectric component of dissipation factor dielektrischer anteil des verlustfaktors tan d p parallel component of dissipation factor parallelanteil des verlfustfaktors tan d s series component of dissipation factor serienanteil des verlustfaktors t a ambient temperature umgebungstemperatur t max upper category temperature obere kategorietemperatur t min lower category temperature untere kategorietemperatur t ol operating life at operating temperature and voltage betriebszeit bei betriebstemperatur und -spannung t op operating temperature beriebstemperatur t r rated temperature nenntemperatur t ref reference temperature referenztemperatur t sl reference service life referenz-lebensdauer v ac ac voltage wechselspannung b32671z ... b32673z power factor correction page 18 of 20 please read cautions and warnings and important notes at the end of this document.
symbol english german v c category voltage kategoriespannung v c,rms category ac voltage (sinusf?rmige) kategorie-wechselspannung v cd corona-discharge onset voltage teilentlade-einsatzspannung v ch charging voltage ladespannung v dc dc voltage gleichspannung v fb fly-back capacitor voltage spannung (flyback) v i input voltage eingangsspannung v o output voltage ausgangssspannung v op operating voltage betriebsspannung v p peak pulse voltage impuls-spitzenspannung v pp peak-to-peak voltage impedance spannungshub v r rated voltage nennspannung r amplitude of rated ac voltage amplitude der nenn-wechselspannung v rms (sinusoidal) alternating voltage, root-mean-square value (sinusf?rmige) wechselspannung v sc s-correction voltage spannung bei anwendung "s-correction" v sn snubber capacitor voltage spannung bei anwendung "beschaltung" z impedance scheinwiderstand lead spacing rasterma? b32671z ... b32673z power factor correction page 19 of 20 please read cautions and warnings and important notes at the end of this document.
the following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical re- quirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application . as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons, it is always ultimately incum- bent on the customer to check and decide whether an epcos product with the properties de- scribed in the product specification is suitable for use in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified . in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-specific notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our ma- terial data sheets on the internet (www.epcos.com/material). should you have any more de- tailed questions, please contact our sales offices. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product specifications. please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . consequently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the fore- going for customer-specific products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current ver- sion of the "general terms of delivery for products and services in the electrical in- dustry" published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, ceralink, csmp, cssp, ctvs, deltacap, digisimic, dssp, filtercap, formfit, miniblue, minicell, mkd, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks. important notes page 20 of 20

▲Up To Search▲

Price & Availability of B32671Z6683

	To Download B32671Z6683 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .