View ATZB-S1-256-3-0-U-14_8001501.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

zigbit 2.4ghz single chip wireless module atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf datasheet features ? ultra compact size (30.0 20.0mm) ? high rx sensitivity (-98dbm) ? outperforming link budget (up to 102db) ? up to +4dbm output power ? very low power consumption: ? 17ma in rx mode (1) ? 16.4ma in tx mode (1) ? 0.6a in sleep mode (2) ? ample memory resources (256k bytes in-system, self-programmable flash memory, 8k bytes eeprom, 32k bytes sram) ? wide range of interfaces (both analog and digital) ? 4-wire spi, twi ? isp, jtag ? two analog comparator input ? uart, usart ? timer, pwm ? four adc lines ? external clock input, internal clock output ? upto 31 lines configurable as gpio ? preassigned atmel mac address that can be used on end product ? capability to use mac address into the internal eeprom ? ieee ? 802.15.4 compliant transceiver ? 2.4ghz ism band ? serial bootloader ? high performance low power atmel avr ? 8-bit microcontroller ? u.fl antenna connector to select approved antennae upto 5dbi ? small physical footprint and low profile for optimum fit in very small application boards ? mesh networking capability ? easy-to-use low cost development kit ? single source of support for hw and sw ? worldwide license-free operation notes: 1. mcu is in active state with 3v supply, cp u clock @ 16mhz, rx rpc enabled (for rx current), phy_tx_pwr=0x0 (for tx current), all digital outputs pulled high. 2. controller sleep mode: sleep_mode_pwr_down. 42199b ? wireless ? 04/2014
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 2 table of contents 1.? introduction .......................................................................................... 3 ? 1.1 ? summary ........................................................................................................... 3 ? 1.2 ? abbreviations and acrony ms ............................................................................ 3 ? 1.3 ? related documents ........................................................................................... 4 ? 2.? zigbit module overview ....................................................................... 5 ? 2.1 ? overview ........................................................................................................... 5 ? 3.? specificatio ns ....................................................................................... 7 ? 3.1 ? electrical char acteristics ................................................................................... 7 ? 3.1.1 ? absolute maxi mum ratings ................................................................ 7 ? 3.1.2 ? power supply ...................................................................................... 7 ? 3.2 ? rf characteristics ............................................................................................. 8 ? 3.2.2 ? microcontroller characteristics ............................................................ 8 ? 3.2.3 ? module interfaces characteri stics ....................................................... 9 ? 3.3 ? physical/environmental char acteristics and out line ......................................... 9 ? 3.4 ? pin configuration ............................................................................................... 9 ? 3.5 ? mounting info rmation ...................................................................................... 10 ? 3.6 ? list of approv ed antennas .............................................................................. 12 ? 3.7 ? soldering profile .............................................................................................. 12 ? 4.? schematics ........................................................................................ 13? 4.1 ? handling instructions ....................................................................................... 17 ? 4.2 ? general recomm endati ons ............................................................................ 17 ? 5.? persistence memory .......................................................................... 18? 6.? ordering information .......................................................................... 19? 7.? agency cert ifications ? atzb-s1-256-3-0-u ..................................... 20? 7.1 ? united stat es (fcc) ........................................................................................ 20 ? 7.2 ? european unio n (etsi) ................................................................................... 20 ? 7.3 ? industry canada (ic) co mpliance st atements ................................................ 21 ? 8.? agency cert ifications ? atzb-s1-256-3-0-uf ................................... 22? 8.1 ? united stat es (fcc) ........................................................................................ 22 ? 8.2 ? european unio n (etsi) ................................................................................... 22 ? 8.3 ? industry canada (ic) co mpliance st atements ................................................ 23 ? 9.? revision history ................................................................................. 24?
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 3 1. introduction 1.1 summary atzb-s1-256-3-0-u zigbit ? is an ultra-compact and low-power 2.4ghz ieee 802.15.4/zigbee ? oem module from atmel. atzb-s1-256-3-0-uf zigbit is a variant that is designed to operate in extended temperature range of -40 ? c to +125? c. based on the innovative mixed-signal hardware platform from atmel, this module uses the atmega256rfr2 soc with the 8-bit avr microcontroller and a high data rate transceiver for the 2.4ghz ism band. the radio transceiver provides high data rates from 250kb/s up to 2mb/s, frame handling, outstanding receiver sensitivity and high transmit output power enabling a very robust wireless communication. the module is designed for wireless sensing, monitoring, control, data acquisition applications, to name a few. this zigbit module eliminates the need for costly and time-consuming rf development, and shortens time-to-market for wireless applications. the module has an u.fl rf connector that can be used to connect any of the approved antenna 1 ? cable assemblies. this gives freedom to applications to choose the external antenna 1 that can be mounted on an end product. the zigbit module is compatible with robust ieee 802.15.4/zigbee stack that supports a self-healing, self-organizing mesh network, while optimizing network traffic and minimizing power consumption. for detailed software support information, visit http://www.atmel.com/products/wireless . the applicatio ns include, but are not limited to: ? building automation and monitoring ? lighting controls ? wireless smoke- and co-detectors ? structural integrity monitoring ? hvac monitoring and control ? inventory management ? environmental monitoring ? security ? water metering ? industrial monitoring ? machinery condition and performance monitoring ? monitoring of plant system parameters such as temperature, pressure, flow, tank level, humidity, vibration, etc. ? automated meter reading (amr) note: 1. external antenna must be selected from a list of approved antennae. 1.2 abbreviations and acronyms adc analog-to-digital converter api application programming interface dc direct current dtr data terminal ready eeprom electrically erasable programmable read-only memory esd electrostatic discharge
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 4 gpio general purpose input/output haf high frequency hvac heating, ventilating, and air conditioning hw hardware i 2 c inter-integrated circuit ieee institute of electrical and electronics engineers irq interrupt request ism industrial, scientific and medical radio band jtag digital interface for debugging of embedded device, also known as ieee 1149.1 standard interface mac medium access control layer mcu microcontroller unit. in this document it also means the processor, which is the core of a zigbit module nre network layer oem original equipment manufacturer ota over-the-air upgrade pa power amplifier pcb printed circuit board per package error ratio ram random access memory rf radio frequency rts/cts request to send/ clear to send rx receiver sma surface mount assembly soc system on chip spi serial peripheral interface sw software ttm time-to-market tx transmitter uart universal asynchronous receiver/transmitter usart universal synchronous/asynchronous receiver/transmitter usb universal serial bus zigbee, zigbee pro wireless networking standards targeted at low-power applications 802.15.4 the ieee 802.15.4-2003 standard applicable to low-rate wireless personal area network 1.3 related documents [1] atmegaa256rfr2 8-bit avr microcontroller with 2.4ghz transceiver for zigbee and ieee 802.15.4. [2] ieee std 802.15.4-2003 ieee standard for information technology - part 15.4 wireless medium access control (mac) and physical layer (phy) specifications for low-rate wireless personal area networks (lr-wpans). [3] zigbee specification. zigbee document 053474r17, october 19, 2007.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 5 2. zigbit module overview 2.1 overview the atzb-s1-256-3-0-u zigbit is an ultra compact, lo w-power, high sensitivity ieee 802.15.4/zigbee oem module. based on a solid combination of the latest atmel mcu wireless hardware platform, 2.4ghz ism band transceiver and atmel studio wireless composer - the zigbit offers an unmatched combination of superior radio performance, ultra-low power consumption and exceptional ease of integration. figure 2-1. atzb-s1-256-3-0-u block diagram this zigbit module contains the atmel atmega256rfr2 microcontroller and a 2.4ghz ism band transceiver for zigbee and ieee 802.15.4 [1] . the module features 256kb in- system self -programmable flash memory, 32kb sram and 8kb eeprom. the compact all-in-one integration of mcu and radio transce iver inside the chip along with very minimal components on the rf path to antenna dramatically improves the zi gbit's compact size, range performance on signal transmission and increases its sensitivity. this ensures stable connectivity within a larger coverage area, and helps develop applications on smaller footprint. zigbit module contains a complete rf/mcu design with all the necessary passive components included. the module can be easily mounted on a simple 2-layer pcb with a minimum of required external connection. the zigbit module evaluation kit containing the zigbit extension board for the atmel xplained pro hw evaluation platform can be used to develop fw using the atmel studio and evaluate using the wireless composer. compared to a custom rf/mcu solution, a module-based solution offers considerable savings in development time and nre cost per unit during the hw/fw design, prototyping, and mass production phases of product development. all zigbits are preloaded with a bootloader when they are sold as modules, either in single units or t&r. depending on end-user design requirements, the zigbit can operate as a self-contained sensor node, where it would function as a single mcu, or it can be paired with a host processor driving the module over a serial interface.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 6 the mac stack running on the host processor can then control data transmission and manages module peripherals. thus very minimal firmware customization is required for a successful module design-in. third-party sensors can then be connected directly to the module, thus expanding the existing set of peripheral interfaces. every zigbit module come pre loaded with atmel assigned 64-bit mac address stored in the signature bytes of the device. this unique ieee mac address can be used as the mac address of the end product, so there is no need to buy a mac address separately for the product using the zigbit.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 7 3. specifications 3.1 electrical characteristics 3.1.1 absolute maximum ratings table 3-1. absolute maximum ratings (1)(2) parameter minimum maximum voltage on any pin, except reset with respect to ground -0.3v 3.6v (v dd max ) input rf level +14dbm voltage on any analog configured pin -0.3v 2.0v voltage on aref (pin 24) -0.3v 2.0v 1. absolute maximum ratings are the values beyond which damage to the device may occur. under no circumstances must the absolute maximum ratings given in this table be violated. stresses beyo nd those listed under "absolute ma ximum ratings" may cause perman ent damage to the device. this is a stress rating only. functional oper ation of the device at these or other co nditions, beyond those indicated in the op erational sections of this specification, is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. attention! the zigbit is an esd-sensitive device. precaution should be taken when handling t he device in order to prevent permanent damage. 3.1.2 power supply table 3-2. test conditions (unless otherwise stated), f = 2.45ghz, v dd = 3v, t amb = 25c parameter range unit supply voltage, v dd 1.8 to 3.6 v active current consumption: rx mode - rx_on ? listening state 17.0 ma active current consumption: tx mode (1) ? busy_tx ? transmit state 16.3 ma active current consumption: tx mode ? pll_on 9.9 ma active current consumption: trx_off 4.7 ma sleep current consumption: power-save mode (2) 0.62 a sleep current consumption: power-down mode (2) 0.6 a sleep current consumption: standby (2) 2.4 ma sleep current consumption: idle (2) 4.9 ma sleep current consumption: ext_standby (2) 0.9 ma note 1: a) output tx power (when measuring consumption in tx mode) is +3dbm. note 2: a) all interfaces are set to the def ault state (see pin assignment table). b) jtag is not connected. c) cpu clock configured when doing this measurement ? 16mhz for all modes except power save and power down modes current consumption depends on multiple factors, including but not limited to, the board design and materials, protocol settings, network activity, eeprom read/write operations. it also depends on mcu load and/or peripherals used by an application.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 8 3.2 rf characteristics table 3-3. rf characteristics parameter condition range unit frequency band 2.4000 to 2.4835 ghz numbers of channels 16 channel spacing 5 mhz transmitter output power adjusted in 16 steps -16.5 to +3.5 dbm receiver sensitivity per = 1% -97 dbm on-air data rate 250, upto 2000 kbps tx output/ rx input nominal impedance unbalanced 50 ? table 3-4. tx power settings phy_tx_pwr 3:0 register value power register setting [dbm] typical output power [dbm] (at rf connector) 0 +3.5 +3.79 1 +3.3 +3.40 2 +2.8 +3.41 3 +2.3 +2.43 4 +1.8 +2.41 5 +1.2 +1.21 6 +0.5 +0.58 7 -0.5 -0.11 8 -1.5 -1.02 9 -2.5 -1.97 10 -3.5 -3.12 11 -4.5 -4.48 12 -6.5 -6.28 13 -8.5 -8.52 14 -11.5 -11.64 15 -16.5 -16.26 3.2.2 microcontroller characteristics table 3-5. atmega256rfr2 characteristics parameters condition range unit on-chip flah memory size 256k bytes on-chip sram size 32k bytes on-chip eeprom size 8k bytes maximum operation frequency 16 mhz
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 9 3.2.3 module interfaces characteristics table 3-6. module interfaces characteristics parameters condition range unit uart maximum baud rate 115.2 kbps adc resolution conversion time free running conversion 3 - 240 s adc input resistance static load resistor of input signal 100 m? adc reference voltage (vref) avdd=1.8v 1.5v to avdd v adc input voltage avdd=1.8v 0 - avdd v twi maximum clock 400 khz gpio high level input voltage except nrst min 0.7 v dd v gpio low level input voltage except nrst max 0.3 v dd v gpio high level input voltage nrst min 0.9 v dd v gpio low level input voltage nrst max 0.1 v dd v gpio high level output voltage v oh i oh = -12ma, v dd = 3.6v i oh = -6ma, v dd = 1.8v min v dd ? 0.4 v gpio low level output voltage v ol i ol = 16ma, v dd = 3.6v i ol = 10ma, v dd = 1.8v max 0.4 v real-time oscillator frequency 32.768 khz 3.3 physical/environmental characteristics and outline table 3-7. physical characteristics parameters value comments size 30.0 x 20.0mm operating temperature range -40c to +85c -40c to +85c operational, atzb-s1-256-3-0-u operating temperature range -40c to +125c -40c to +125c operational, atzb-s1-256-3-0-uf 3.4 pin configuration table 3-8. atzb-s1-256-3-0-u pinout description pinout pin descriptions function 1 avss analog ground 2 avss analog ground 3 devdd digital power input pin 4 devdd digital power input pin 5 rstn reset 6 pb0/ssn/pcint0 spi 7 pb2/mosi/pdi/pcint2 spi/ isp prog 8 pb3/miso/pdo/pcint3 spi/ isp prog 9 pb1/sck/pcint1 spi/ isp prog 10 pe2/aino gpio/aino
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 10 pinout pin descriptions function 11 pe3/ain1/oc3a gpio/ain1/pwm out 12 dvss digital ground 13 pd2/rxd1/int2 uart 14 pd3/txd1/int3 uart 15 pd5/xck1 usart 16 pd4/icp1 timer counter input trigger 17 pd6/t1 tc 18 pg2/amr gpio/tc 19 pb4/oc2a/pcint4 pwm/pcint4 20 pb6/oc1b/pcint6 pwm/pcint6 21 pb7/oc0a/oc1c/pcint7 pwm/pcint/gpio 22 pe0:rxd0:pcint8 gpio/pcint8/rxd0 23 pe1:txd0 gpio/txd0 24 aref adc ref 25 pf0/adc0 adc/ gpio 26 pf1/adc1 adc/ gpio 27 pf2/adc2/dig2 adc/ gpio 28 pf3/adc3/dig4 adc/ gpio 29 dvss digital ground 30 pf4/adc4/tck jtag 31 pf5/adc5/tms jtag 32 pf6/adc6/tdo jtag 33 pf7/adc7/tdi jtag 34 pg5/oc0b pwm output timer 35 pe4/oc3b/int4 wakeup int 36 pd0/scl/int0 twi/int/gpio 37 pd1/sda/int1 twi/int/gpio 38 clki ext clki/ isp programming 39 pe7/icp3/int7/clko clock out put 40 pd7/t0 tc 41 dvss digital ground 42 dvss digital ground 3.5 mounting information the figure below shows the pcb layout recommended for a zigb it module. neither via-holes nor wires are allowed on the pcb upper layer in the area occupied by the module. as a critical requirement, rf_gnd pins should be grounded via several via-holes to be located right next to the pins thus minimizing inductance and preventing both mismatch and losses.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 11 figure 3-1. atzb-s1-256-3-0-u dimensions figure 3-2. atzb-s1-256-3-0-u pinout figure 3-3. atzb-s1-256-3-0-u foot print dimensions
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 12 3.6 list of approved antennas the atzb-s1-256-3-0-u module has been tested and approved by certification body to use any of the antenna listed below or similar antenna with lesser gain. description manufacturer partnumber antenna gain 2.4ghz miniature pigtail antenna from rf solutions ant-24g-s21-p5fl 0dbi 2.4ghz 5dbi rubber antenna with pigtail cable (flying lead) from tekfun m07-fl 5dbi 3.7 soldering profile the j-std-020c-compliant soldering profile is recommended according to table 3-9 . table 3-9. soldering profile (1) profile feature green package average ramp-up rate (217c to peak) 3c/s max preheat temperature 175c 25c 180s max temperature maintained above 217c 60s to 150s time within 5c of actual peak temperature 20s to 40s peak temperature range 260c ramp-down rate 6c/s max time within 25c to peak temperature 8 minutes note: 1. the package is backward compatib le with pb/sn soldering profile.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 13 4. schematics the following schematic drawings for the atzb-s1-256-3-0-u are in the following order: ? top level schematics ? connector schematics ? atmega256rfr2 schematics ? atmega256rfr2 rf antenna schematics
pie101 coe1 cofixture1 colabel1 copcb1 piz201 piz202 piz203 piz204 coz2 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a * a08-1876_toplevel.schdoc 1 4 7/22/2013 3:01:15 pm zigbit mega256rfr2 ufl atmel india chennai india page: of title: document number: revision: 1 date: ojas msk * spi cl k i o uart0 uart1 anal og comparator tim er/counter adc pci nt/ pwm twi jtag w k _i nt rfr2 a08- 1876_m eg arfr2.schdoc spi cl k i o uart0 uart1 anal og comparator tim er/counter adc pci nt/ pwm twi jtag w k _i nt connector a08- 1876_connector.schdoc b a fi duci al 1.5m m e1 z ig bit xm eg arfr2 board pcb pcb1 product num ber/revision serial num ber l abel z ig bit shield l abel 1 gnd_rf 1 2 3 4 emi shield z 2 emi _shi el d a13- 0086 fi xture1
piz101 piz102 piz103 piz104 piz105 piz106 piz107 piz108 piz109 piz1010 piz1011 piz1012 piz1013 piz1014 piz1015 piz1016 piz1017 piz1018 piz1019 piz1020 piz1021 piz1022 piz1023 piz1024 piz1025 piz1026 piz1027 piz1028 piz1029 piz1030 piz1031 piz1032 piz1033 piz1034 piz1035 piz1036 piz1037 piz1038 piz1039 piz1040 piz1041 piz1042 coz1 poadc poadc0adc0 poadc0adc1 poadc0adc2 poadc0adc3 poadc0aref poanalog comparator poanalog comparator0ain0 poanalog comparator0ain1 poclk io poclk io0clki poclk io0clko pojtag pojtag0nrst pojtag0tck pojtag0tdi pojtag0tdo pojtag0tms popcint0 pwm popcint0 pwm0pwm0int4 popcint0 pwm0pwm0int6 popcint0 pwm0pwm0int7 pospi pospi0miso pospi0mosi pospi0sck pospi0ss potimer0counter potimer0counter0amr0input tc2 potimer0counter0pwm out tc0 potimer0counter0t00irq potimer0counter0t1 potimer0counter0trigger input tc1 potwi potwi0scl potwi0sda pouart0 pouart00uart0rxd0 pouart00uart0txd0 pouart1 pouart10uart0rx1 pouart10uart0tx1 pouart10xlk1 powk0int 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a * a08-1876_connector.schdoc 2 4 7/22/2013 3:01:15 pm zigbit mega256rfr2 ufl atmel india chennai india page: of title: document number: revision: 1 date: ojas msk * pe3_ai n1_oc3a pd3_txd1_i nt3 pd5_xck1 pd4_i cp1 pg2_amr pb4_oc2a_pci nt4 pb6_oc1b_pci nt6 pe0_pci nt8 cl ki pf0_adc0 pf1_adc1 pf2_adc2_di g2 pf3_adc3_di g4 pf5_adc5_tms pf6_adc6_tdo pf7_adc7_tdi aref vcc_3v3 pd6_t1 pe2_ai no pd2_rxd1_i nt2 pb7_oc0a_oc1c_pci nt7 pf4_adc4_tck pe7_i cp3_i nt7_cl ko pb3_mi so_pdo_pci nt3 pb2_mosi _pdi _pci nt2 pb0_ssn_pci nt0 pb1_sck_pci nt1 pd0_scl _i nt0 pd1_sda_i nt1 pg5_oc0b gnd 1 gnd 2 vdd 3 vdd 4 rstn 5 pe2/xck0/ain0 10 pe3/oc3a/ain1 11 gnd 12 pd2/rxd1/int2 13 pd3/txd1/int3 14 pd5/xck1 15 pd4/icp1 16 pd6/t1 17 pg2/amr 18 pb4/oc2a/pcint4 19 pb6/oc1b/pcint6 20 pb7/oc0a/oc1c/pcint7 21 pe0/rxd0/pcint8 22 pe1/txd0 23 aref 24 pf0/adc0 25 pf2/adc2/dig2 27 pf3/adc3/dig4 28 gnd 29 pf4/adc4/tck 30 pf5/adc5/tms 31 pf6/adc6/tdo 32 pf7/adc7/tdi 33 pg5/oc0b 34 pe4/oc3b/int4 35 pf1/adc1 26 pd0/scl/int0 36 clki 38 pe7/icp3/int7/clko 39 pd1/sda/int1 37 pd7/t0 40 gnd 42 gnd 41 pb3/miso/pdo/pcint3 8 pb1/sck/pcint1 9 pb2/mosi/pdi/pcint2 7 pb0/ssn/pcint0 6 z 1 z b_rfr2_outl i ne gnd_rf gnd_rf gnd_rf gnd_rf pe1_txd0 sck mi so mosi ss spi spi ai n0 ai n1 analog com parator i /p analog comparator xl k1 uart_rx1 uart_tx1 uart1 uart1 t0/i rq t1 amr/input tc2 pwm out tc0 trig g er i nput tc1 tim er/counter timer/counter pwm/i nt4 pwm/i nt6 pwm/i nt7 pci nt/ pwm output pcint/ pwm uart_rxd0 uart_txd0 uart0 uart0 adc0 adc1 adc2 adc3 aref adc adc tck tdi tdo tms nrst jtag jtag scl sda twi twi cl ko cl ki cl k i o clk io nrst pd7_t0 wake up int wk_int pe4_oc3b_i nt4 nrst nrst pg5_oc0b pg5_oc0b pd7_t0 pd7_t0
pib101 pib102 pib103 pib104 pib105 pib106 cob1 pic101 pic102 coc1 pic201 pic202 coc2 pic301 pic302 coc3 pic401 pic402 coc4 pic501 pic502 coc5 pic601 pic602 coc6 pic701 pic702 coc7 pic801 pic802 coc8 pic901 pic902 coc9 pic1001 pic1002 coc10 pic1101 pic1102 coc11 pic1201 pic1202 coc12 pic1301 pic1302 coc13 pic1401 pic1402 coc14 pil101 pil102 col1 pil201 pil202 col2 pip101 pip102 pip103 cop1 piq101 piq102 coq1 piq201 piq202 piq203 piq204 coq2 pir101 pir102 cor1 pir201 pir202 cor2 pir301 pir302 cor3 piu101 piu102 piu103 piu104 piu105 piu106 piu107 piu108 piu109 piu1010 piu1011 piu1012 piu1013 piu1014 piu1015 piu1016 piu1017 piu1018 piu1019 piu1020 piu1021 piu1022 piu1023 piu1024 piu1025 piu1026 piu1027 piu1028 piu1029 piu1030 piu1031 piu1032 piu1033 piu1034 piu1035 piu1036 piu1037 piu1038 piu1039 piu1040 piu1041 piu1042 piu1043 piu1044 piu1045 piu1046 piu1047 piu1048 piu1049 piu1050 piu1051 piu1052 piu1053 piu1054 piu1055 piu1056 piu1057 piu1058 piu1059 piu1060 piu1061 piu1062 piu1063 piu1064 piu1065 cou1 poadc poadc0adc0 poadc0adc1 poadc0adc2 poadc0adc3 poadc0aref poanalog comparator poanalog comparator0ain0 poanalog comparator0ain1 poclk io poclk io0clki poclk io0clko pojtag pojtag0nrst pojtag0tck pojtag0tdi pojtag0tdo pojtag0tms popcint0 pwm popcint0 pwm0pwm0int4 popcint0 pwm0pwm0int6 popcint0 pwm0pwm0int7 pospi pospi0miso pospi0mosi pospi0sck pospi0ss potimer0counter potimer0counter0amr0input tc2 potimer0counter0pwm out tc0 potimer0counter0t00irq potimer0counter0t1 potimer0counter0trigger input tc1 potwi potwi0scl potwi0sda pouart0 pouart00uart0rxd0 pouart00uart0txd0 pouart1 pouart10uart0rx1 pouart10uart0tx1 pouart10xlk1 powk0int 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a * a08-1876_megarfr2.schdoc 3 4 7/22/2013 3:01:16 pm zigbit mega256rfr2 ufl atmel india chennai india page: of title: document number: revision: 1 date: ojas msk * pf2:adc2:dig2 1 pf3:adc3:dig4 2 pf4:adc4:tck 3 pf5:adc5:tms 4 pf6:adc6:tdo 5 pf7:adc7:tdi 6 pf1:adc1 64 pf0:adc0 63 pb0:ssn:pcint0 36 pb1:sck:pcint1 37 pb2:mosi:pdi:pcint2 38 pb3:miso:pdo:pcint3 39 pb4:oc2a:pcint4 40 pb5:oc1a:pcint5 41 pb6:oc1b:pcint6 42 pb7:oc0a:oc1c:pcint7 43 pd0:scl:int0 25 pd1:sda:int1 26 pd2:rxd1:int2 27 pd3:txd1:int3 28 pd4:icp1 29 pd5:xck1 30 pd6:t1 31 pd7:t0 32 pe0:rxd0:pcint8 46 pe1:txd0 47 pe2:xck0:ain0 48 pe3:oc3a:ain1 49 pe4:oc3b:int4 50 pe5:oc3c:int5 51 pe6:t3:int6 52 pe7:icp3:int7:clko 53 pg0:dig3 14 pg1:dig1 15 pg2 / amr 16 pg3:tosc2 17 pg4:tosc1 18 pg5:oc0b 19 devdd 23 devdd 34 devdd 44 devdd 54 dvss 24 dvss 35 dvss 45 dvss 55 a v s s _ r f p 7 r f p 8 r f n 9 a v s s _ r f n 1 0 avss:asvss 58 avss 61 evdd 59 avdd 60 dvdd 21 dvdd 22 dvss:dsvss 20 xtal2 56 xtal1 57 aref 62 clki 33 paddle 65 tst 11 rstn 12 rston 13 atmega256rfr2z u u1 rf_vcc_3v3 rf_vcc_3v3 rf_vcc_3v3 gnd_rf gnd_rf gnd_rf gnd_rf pe3_ai n1_oc3a pd0_scl _i nt0 pd1_sda_i nt1 pe7_i cp3_i nt7_cl ko pe2_ai no pd3_txd1_i nt3 pd5_xck1 pd4_i cp1 pg2_amr pb4_oc2a_pci nt4 pb6_oc1b_pci nt6 pd6_t1 pd2_rxd1_i nt2 pe0_pci nt8 pf0_adc0 pf1_adc1 pf2_adc2_di g2 pf3_adc3_di g4 pe1_txd0 aref pb7_oc0a_oc1c_pci nt7 cl ki pb0_ssn_pci nt0 pf5_adc5_tms pf6_adc6_tdo pf7_adc7_tdi pb1_sck_pci nt1 pf4_adc4_tck 10 k r3 10 k r2 100k r1 100n c1 1uf c5 1uf c4 pb3_mi so_pdo_pci nt3 pb2_mosi _pdi _pci nt2 gnd_rf gnd_rf gnd_rf 10 pf c2 10 pf c3 fc- 135 32.768 k hz q1 gnd_rf gnd_rf gnd_rf 10 pf c6 10 pf c7 100n c11 100n c12 100n c9 100n c10 + 4.7uf/10v c13 gnd_rf rf_vcc_3v3 rf_vcc_3v3 gnd_rf 100n c14 rf_vcc_3v3 bl m15bb221sn1 l 1 vcc_3v3 tosc2 tosc1 gnd_rf gnd_rf gnd_rf xtal 1 xtal 2 rf_vcc_3v3 gnd_rf sck mi so mosi ss spi spi scl sda twi twi xl k1 uart_rx1 uart_tx1 uart uart1 adc0 adc1 adc2 adc3 aref adc adc cl ko cl ki cl k i o clk io uart_rxd0 uart_txd0 uart0 uart0 pwm/i nt4 pwm/i nt6 pwm/i nt7 pci nt/ pwm output pcint/ pwm t0/i rq t1 amr/input tc2 pwm out tc0 trig g er i nput tc1 tim er/counter timer/counter gnd_rf clki clki pg5_oc0b nrst nrst pd7_t0 wake up int irq ai n0 ai n1 analog com parator i /p analog comparator tck tdi tdo tms nrst jtag jtag pe4_oc3b_i nt4 1 3 2 4 16.0mhz q2 wk_int rf_p rf_n dif f erentialpair: true i pcb rule i pcb rule gnd_rf 50ohm 1 g n d 2 bal 3 bal 4 g n d 5 g n d 6 2450bm15a0015e b1 gnd_rf rf_n rf_p gnd_rf gnd_rf 3 pf c8 3 . 3 n h l 2 gnd_rf 3 2 1 u.fl - r- smt- 1(10) p1 place x tal circuit closer to mcu. i solate f rom dig ital sig nals. place de- coupling closer to mcu place 4.7uf closer to vcc input f or m odule place close to i c pin 62. 50ohm i m pedance controlled track 100 ohm dif f erential. route as shortest track .
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 17 4.1 handling instructions the zigbit modules are fixed with an emi shield to ensure compliance to emission and immunity rules. this shield is galvanic and not air tight. so cleaning of the module with ipa / other similar agents is not advised. humidity protection coating (conformal) will cause deviated rf behavior and coating material being trapped inside emi shield. so this should be avoided. for products requiring conformal coating, it is advised to suitably mask the zigbit before applying the coating to rest of the zigbit carrier board. to protect zigbit from humidity, the housing of the product should ensure suitable ingress protection standards are complied with. the ufl connector should never be exposed to varnish / similar conformal coating material which will affect electrical connection on the surfaces of connector. 4.2 general recommendations ? metal enclosure should not be used. using low profile enclosure might also affect antenna tuning ? placing high profile components next to antenna should be avoided ? having holes/vias punched around the periphery of the board eliminates parasitic radiation from the board edges also distorting antenna pattern ? zigbit module should not be placed next to consumer elec tronics which might interfere with zigbit's rf frequency band
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 18 5. persistence memory a dedicated memory space is allocated to store product specific information and called the persistence memory. the organization of the persistence memory is as follows: table 5-1. persistence memory data size structure revision 2 bytes mac address (1) 8 bytes board information overall 49 bytes board information ? pcba name 30 bytes board information ? pcba serial number 10 bytes board information ? pcba atmel part number 8 bytes board information ? pcba revision 1 byte resereved 3 bytes xtal calibration value 1 byte reserved 7 bytes reserved 4 bytes crc 1 byte in atzb-s1-256-3-0-u persistence memory is stored in the user signature data (page 1) of atmega256rfr2 soc with starting address 0x0100. user signature data is isolated from the main flash and will not be cleared by chip erase command. special commands are available to erase and write data to user signature pages via the jtag interface (see section on "programming via the jtag interface? in the atmega256rfr2 datasheet [1] for details). user signat ure rows can be read from software in the same way as the device and jtag identifiers (see section "reading the signature row from software" in the atmega256rfr2 datasheet [1] ). note: 1 the mac address stored inside the mcu is a uniquely assigned id for each zigbit and owned by atmel. user of the zigbit application can use this unique mac id to address the zigbit in end-applications . the mac id can be read from the zigbit using the performa nce analyzer application that can be downloaded from www.atmel.com/wireless .
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 19 6. ordering information part number description atzb-s1-256-3-0-u 2.4ghz ieee802.15.4/zigbee oe m module based on atmega256rfr2 soc with ufl antenna connector, single unit atzb-s1-256-3-0-ur 2.4ghz ieee802.15.4/zigbee oe m module based on atmega256rfr2 soc with ufl antenna connector, tape and reel atzb-s1-256-3-0-uf 2.4ghz ieee802.15.4/zigbee oe m module based on atmega256rfr2 soc with ufl antenna connector, single unit, extended temperature atzb-s1-256-3-0-ufr 2.4ghz ieee802.15.4/zigbee oe m module based on atmega256rfr2 soc with ufl antenna connector, tape and reel, extended temperature note: tape and reel quantity: 200.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 20 7. agency certifications ? atzb-s1-256-3-0-u 7.1 united states (fcc) this equipment complies with part 15 of the fcc rules and regulations. to fulfill fcc certification requirements, an oem manufacturer must comply with the following regulations: 1. the atzb-s1-256-3-0-u modular transmi tter must be labeled with its own fcc id number, and, if the fcc id is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. this exterior label can use wording such as the following: important : contains fcc id: vw4a092074. this equipment complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (fcc 15.19). the antenna used for this mobile transmitter must provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying rf exposure compliance. this device is approved as a mobile device with respect to rf exposure compliance, and may only be marketed to oem installers. use in portable exposure conditions (fcc 2.1093) requires separate equipment authorization. important : modifications not expressly approved by this company could void the user's authority to operate this equipment (fcc section 15.21). important : this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (fcc section 15.105). 7.2 european union (etsi) the atzb-s1-256-3-0-u module has been certified for use in european union countries. if these modules are incorporated into a product, the manufacturer must ensure compliance of the final product to the european harmonized emc and lowvoltage/safety standards. a declaration of conformity must be issued for each of these standards and kept on file as described in annex ii of the r&tte directive.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 21 furthermore, the manufacturer must maintain a copy of the modules' documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. if any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards. important : the 'ce' marking must be affixed to a visible location on the oem product. the ce mark shall consist of the initials "ce" taking the following form: the ce marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. the ce marking must be affixed visibly, legibly, and indelibly. more detailed information about ce marking requirements you can find at "directive 1999/5/ec of the european parliament and of the council" on 9 march 1999 at section 12. 7.3 industry canada (ic) compliance statements this device complies with industry canada licence-exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'industrie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. this equipment complies with radio frequency exposure limits set forth by industry canada for an uncontrolled environment. this equipment should be installed and operated with minimum distance 20 cm between the device and the user or bystanders. cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par industrie canada pour un environnement non contr?l. cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre le dispositif et l'utilisateur ou des tiers. caution: any changes or modifications not expressly approved by the party responsible for compliance could void the user?s authority to operate the equipment. the oem integrator is still responsible for testing thei r end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, pc peripheral requirements, etc.). this module is labelled with its own ic id. if the ic id certification number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. in that case, the final end product must be labelled in a visible area with the following: ?contains transmitter module ic:11019a-092074? or ?contains ic: 11019a-092074? ce module est tiquet avec son propre id ic. si le numro de ce rtification ic id n'est pas visible lorsqu'il est install l'intrieur d'un autre appareil, l'appareil doit afficher l'tiquette sur le module de rfrence ci-joint. dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant: ?contains transmitter module ic: 11019a-092074? or ?contains ic: 11019a-092074?.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 22 8. agency certifications ? atzb-s1-256-3-0-uf 8.1 united states (fcc) this equipment complies with part 15 of the fcc rules and regulations. to fulfill fcc certification requirements, an oem manufacturer must comply with the following regulations: 1. the atzb-s1-256-3-0-uf modular transmitter must be la beled with its own fcc id number, and, if the fcc id is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. this exterior label can use wording such as the following: important : contains fcc id : vw4a092107. this equipment complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (fcc 15.19). the antenna used for this mobile transmitter must provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying rf exposure compliance. this device is approved as a mobile device with respect to rf exposure compliance, and may only be marketed to oem installers. use in portable exposure conditions (fcc 2.1093) requires separate equipment authorization. important : modifications not expressly approved by this company could void the user's authority to operate this equipment (fcc section 15.21). important : this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (fcc section 15.105). 8.2 european union (etsi) the atzb-s1-256-3-0-uf module has been certified for us e in european union countries. if these modules are incorporated into a product, the manufacturer must ensure compliance of the final product to the european harmonized emc and lowvoltage/safety standards. a declaration of conformity must be issued for each of these standards and kept on file as described in annex ii of the r&tte directive.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 23 furthermore, the manufacturer must maintain a copy of the modules' documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. if any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards. important : the 'ce' marking must be affixed to a visible location on the oem product. the ce mark shall consist of the initials "ce" taking the following form: the ce marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. the ce marking must be affixed visibly, legibly, and indelibly. more detailed information about ce marking requirements you can find at "directive 1999/5/ec of the european parliament and of the council" on 9 march 1999 at section 12. 8.3 industry canada (ic) compliance statements this device complies with industry canada licence-exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'industrie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. this equipment complies with radio frequency exposure limits set forth by industry canada for an uncontrolled environment. this equipment should be installed and operated with minimum distance 20cm between the device and the user or bystanders. cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par industrie canada pour un environnement non contr?l. cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre le dispositif et l'utilisateur ou des tiers. caution: any changes or modifications not expressly approved by the party responsible for compliance could void the user?s authority to operate the equipment. the oem integrator is still responsible for testing thei r end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, pc peripheral requirements, etc.). this module is labelled with its own ic id. if the ic id certification number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. in that case, the final end product must be labelled in a visible area with the following: ?contains transmitter module ic:11019a-092107? or ?contains ic: 11019a-092107?. ce module est tiquet avec son propre id ic. si le numro de ce rtification ic id n'est pas visible lorsqu'il est install l'intrieur d'un autre appareil, l'appareil doit afficher l'tiquette sur le module de rfrence ci-joint. dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant: ?contains transmitter module ic: 11019a-092107? or ?contains ic: 11019a-092107?.
atzb-s1-256-3-0-u / atzb-s1-256-3-0-uf zi gbit 2.4ghz single chip wireless module [datasheet] 42199b ? wireless ? 04/2014 24 9. revision history doc. rev. date comments 42199b 04/2014 some minor corrections ha ve been made in section 1.1 . the orientation of the schematics in chapter 4 has cha nged and some other, minor changes according to the template have been made. 42199a 03/2014 initial revision.
atmel corporation 1600 technology drive san jose, ca 95110 usa tel: (+1)(408) 441-0311 fax: (+1)(408) 436-4200 www.atmel.com a tmel asia limited unit 01-5 & 16, 19f bea tower, millennium city 5 418 kwun tong road kwun tong, kowloon hong kong tel: (+852) 2245-6100 fax: (+852) 2722-1369 a tmel munich gmbh business campus parkring 4 d-85748 garching b. munich germany tel: (+49) 89-31970-0 fax: (+49) 89-3194621 atmel japan g.k. 16f shin-osaki kangyo building 1-6-4 osaki shinagawa-ku, tokyo 141-0032 japan tel: (+81)(3) 6417-0300 fax: (+81)(3) 6417-0370 ? 2014 atmel corporation. all rights reserved. / rev.: 42199b ? wireless ? 04/2014 atmel ? , atmel logo and combinations thereof, enabling unlimited possibilities?, avr ? , zigbit ? , and others are registered trademarks or trademarks of atmel corporation or its subsidiaries. other terms and product names may be trademarks of others. disclaimer: the information in this document is provided in connection with atmel products. no license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of atmel products. except as set forth in the atmel terms and conditions of sales locat ed on the atmel website, atmel assumes no liability whatsoever and disclaims any express, implied or st atutory warranty relating to its products including, but not li mited to, the implied warranty of merchantability, fitness for a particular purpose, or non-infringement. in no event sh all atmel be liable for any d irect, indirect, consequential, punitive, special or incidental damages (including, without limitation, damages for loss and profits, business i nterruption, or loss of information) arising out of the use or inability to use this document, even if atmel has been advised of the possibility of suc h damages. atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the ri ght to make changes to specifications and products descriptions at any time without notice. atmel does not make any commitment to update the information contained herein. unless specifically provided otherwise, atmel products are not suitable for, and shall not be used in, automotive applications. atmel products are not intended, authorized, or warranted for use as components in applications intend ed to support or sustain life.

▲Up To Search▲

Price & Availability of ATZB-S1-256-3-0-U-14

	To Download ATZB-S1-256-3-0-U-14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .