?a1qla?|3--?q kingstate electronics corp 2/6 KPEG006 a. scope ?d? this specification applies receiver, KPEG006 |13w?????a????1, KPEG006 b. specification 3w?? no. item symbol unit specification condition 1 dimension ?o mm p 22.5 x 3.2 refer to attached drawing in details 2 impedance ay? [ ohm 2000 25% at 1khz 3 s.p.l. -?|? db 108 3 at 1khz 1.0v with iec318 coupler 4 operating temp. ?t@?? j -30 ~ +85 5 storage temp. x|s?? j -40 ~ +95 6 electrostatic capacity r1q?e?q pf 90,000 30% at 120hz/0.25v 7 weight -??q g 1.1 8 material ? abs ul-94 1/16? hb high heat ?] black ?^ 9 environmental protection regulation ??oak3w rohs
?a1qla?|3--?q kingstate electronics corp 3/6 KPEG006 c. typical frequency response curve w2v?t3|?u d. appearance drawing ~?[?o1? tol: 0.3 unit: mm 70 80 90 100 110 120 20 200 2k 20k db hz 3.2 22.5 100 term.2(black) term.1(red) ul1571 lf 32awg 5 ?2 ?5
?a1qla?|3--?q kingstate electronics corp 4/6 KPEG006 e. measurement method ??q???u f. arpiece drawing
?a1qla?|3--?q kingstate electronics corp 5/6 KPEG006 g. mechanical characteristics ???s? no. item test conditions evaluation standard 1 solderability 2k?at?? (connector excepted) ( oyl?t?a?|1? ) stripped wires of lead wires are immersed in rosin for 5 seconds and then immersed in solder bath of +2705 j for 30.5 seconds. ?r?u3???jaq-??2g 5 ?? , |a??j +2705 j???2k?? 30.5 ? . 90% min. stripped wires shall be wet with solder.(except the edge of terminal) ??j?r?u3?at?2k 90% hw .( ?oya_-oa ) 2 lead wire pull strength ?u??o the pull force shall be applied to double lead wire ?g horizontal 3.0n(0.306kg) for 30 seconds. vertical 2.0n(0.204kg) for 30 seconds. a?u??-J|v?ih 3.0n(0.306kg) aoo?q , ??a?J|v?ih 2.0n(0.204kg) aoo?q , |u 30 ? . no damage and cutting off ?u??p? , 2?? 3 vibration test ?????? receiver shall be measured after being applied vibration of amplitude of 1.5mm with 10 to 55hz band of vibration frequency to each of 3 per-pendicular directions for 2 hours. ????gai?? 10 ?? 55hz ?bt??t 1.5mm ? x.y.z 3 -J|v , |u 2 p? . 4 drop test ?u??? drop the receiver contained in normal box onto the board 40mm thick 10 times from the height of 75cm n??1?m?2 , |? 75 ?Fa??|b 40mm Naow|@ 10 |? . no obstacle to be harmful to normal operation; damages, cracks, rusts and distortions. should not be audible at 1.0v sine wave between 250hz~4khz ????l?|??a??a?` ?t@ . b|b?j 1.0v ???ai q 250hz 4khz ??l2 `- h. environment test ?1??? no. item test conditions evaluation standard 1 high temp. test a???? after being placed in a storage at +95 j for 240 hours. ?m? +95 j?1 240 p? . 2 low temp. test c???? after being placed in a storage at -40 j for 240 hours. ?m? -40 j?1 240 p? . 3 humidity test ??1?????? after being placed in a storage at +40 j and 955%rh relative humidity for 240 hours. ?m? +40 j , ??1??? 955% ?1 240 p? being placed for 2 hours at +25 j , receiver shall be measured. no obstacle to be harmful to normal operation; damages, cracks, rusts, etc. should not be audible at 1.0v, sine wave between 250 ~ 4khz. s.p.l. deviation of unit should be within 3.5db ?g???? , r?m? +25 j ?]????^ ?1 2 p?? , ? ???l?|??a??a?`?t @ . b|b?j 1.0v ???aiq 250 4khz ??l2`- ?x-????q|b 3.5db o
?a1qla?|3--?q kingstate electronics corp 6/6 KPEG006 i. reliability test ?h????? no. item test conditions evaluation standard 1 load test 3s?-t2 1.0vrms, white noise is applied for 5 hours at room temp. |b???u , ?j\2v 1.0vrms, ?a?-3s??t@ 5 p? . no obstacle to be harmful to normal operation; damages, cracks, rusts, etc. should not be audible at 1.0v sine wave between 250~4khz. s.p.l. deviation of unit should be within 3.5db ????l?|??a??a?` ?t@ . b|b?j 1.0v ???ai q 250 4khz ??l2` -?x-????q|b 3.5db o test condition. standard test condition : a) temperature : +5 ~ +35 j b) humidity : 45-85% c) pressure : 860-1060mbar @????? : a) ?? : +5 ~ +35 j b) ?? : 45-85% c) ?e : 860-1060mbar judgement test condition : a) temperature : +25 2 j b) humidity : 60-70% c) pressure : 860-1060mbar a?n????? : a) ?? : +25 2 j b) ?? : 60-70% c) ?e : 860-1060mbar j. packing standard ]??3w??
|