designed & dimensioned in millimeters[inches] do not scale from this print QRF8-XXX-XX-X-RA-GP-XX no of positions -026, -052, -078 (per row) solder tail lead style -01: 1.57[.062] board *-02: 2.36[.093] board plating specification -s: selective, 30au / 50ni min on contact, matte tin on tail (use c-288-xx-s & im-t-1g36-xx-s) -l: light selective,30au / 50ni min on contact, matte tin on tail (use c-288-xx-l & im-t-1g36-xx-l) option -k: polyimide film (not available for -026 & -078) (use k-500-300, see fig. 2, sht 4) guide posts requirement -gp (see note 9) -ra right angle (* = not tooled) -tr: tape & reel (see note 10) "c" ref (see table 2, sht 2) 24.80 (typ) .976 "b" (see table 2, sht 2) 0.800 (typ) .0315 (tol non-accum) 0.30 .012 ref (typ) 0.50 ref .020 0.30 ref (typ) .012 2.75 .108 ref (typ) 19.25 ref .758 "h" (see table 3, sht 2) 3 max sway (either direction, -052 & -078 only) "a" "a" "c" "c" pin 01 pin 02 c l c c c "a" ref (see table 2, sht 2) 1.25 .049 ref 10.51 .414 ref 9.79 .385 ref qrf8-xxx-xx-x-ra-gp wt-36-xx-t (4 plcs) c l wt-36-xx-t (-052 & -078 only) "d" ref (see table 2, sht 2) "b" (see table 2, sht 2) 1.32 .052 ref 0.800 (typ) .0315 (tol non-accum) "f" (see table 2, sht 2) "e" (see table 2, sht 2) 4.43 .174 ref 9.31 .367 (2 plcs) 6.51 .256 (2 plcs) 1.32 .052 ref 1.10 .043 ref c c c l c c c c "g" (4 plcs) 0.50 .020 ref (typ) 0.20 .008 ref (typ) 0.90 .035 ref 0.30 .012 ref 5.13 .202 ref view "c"-"c" scale 4 : 1 c c fig 1 (qrf8-052-02-x-ra-gp shown) (some detail removed for clarity) d d sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles x.x: 0.3 [.01] 2 x.xx: 0.13 [.005] x.xxx: 0.051 [.0020] material: 0.8mm q-rate right angle socket assembly by: QRF8-XXX-XX-X-RA-GP-XX dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 09/19/2008 5 1 sheet scale: 2:1 insulators: lcp contact : phos bronze ground plane: phos bronze f:\dwg\misc\mktg\QRF8-XXX-XX-X-RA-GP-XX-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: signal: 2.22n[.5 lb]. ground plane: 4.45n[1 lb]. 4. note deleted. 5. measure at bend tangency. 6. measure on pins only, standoffs not included in measurement. 7. post height variation between any two pins: 0.05[.002] maximum. 8. first row tails to be flush to .08 above the second row. 9. parts with the -gp option must mate to -gp optioned qrm8 parts. 10. parts to be packaged in trays, unless -tr option is specified. -078 position is not available in tape and reel. 11. cpc's must be measured both ends of comb or connector. 12. use inspection fixture # at-2298-801-01 to check criticals. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision d free datasheet http://
1.45 0.12 .057 .005 1.19 (ref) .047 3.26 .128 (ref) 0.44 (ref) .017 "g" ref 3.99 .157 (-052 & -078 only, center weld tab) 7.95 .313 6.98 0.10 .275 .004 9.79 0.10 .386 .004 "h" ref 0.96 0.08 .038 .003 (typ) 2.78 ref .110 section "a"-"a" scale 8 : 1 c-288-01-x c-288-02-x im-t-1g36-xx-x c c c c c c c (see note 6) see top row - tail detail 'm' see bottom row - tail detail 'l' d d d d d d see table 4 -c- 0.05 .002 (see note 5) bottom row - tail detail 'l' (locate assy on datum -c- for measurments) c d 0.00 - 0.02 + 0.08 .000 - .001 + .003 (see note 5) top row - tail detail 'm' (locate assy on datum -c- for measurments) c d d d sheet of 0.8mm q-rate right angle socket assembly by: QRF8-XXX-XX-X-RA-GP-XX dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 09/19/2008 5 2 sheet scale: 2:1 revision d f:\dwg\misc\mktg\QRF8-XXX-XX-X-RA-GP-XX-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 free datasheet http://
r 0.35 .014 (2 plcs) 1.288 .0507 (see note 11) 1.269 .0500 (see note 5 & 11) 2 - 2 + 1 (see note 11) 88 - 2 + 1 (see note 11) 0.50 .020 measure point for c23 c c c in process 1 (form contact c-288-02-x) c 10.38 .409 (ref) 0.05 ref .002 6.01 ref .237 c-288-02-x in process 2 (fill bottom row) (see inspection view 1 for assembly orientation and cpc's) -c- 6.98 ref .275 0.96 ref .038 0.05 ref .002 shear carrier in process 3 (cutoff of carrier) (see inspection view 1 for assembly orientation and cpc's) -c- see table 4, sht 2 within row 0.25 .010 ref 8.84 .348 7.95 0.08 .313 .003 im-t-1g36-xx-x in process 4 (fill over molded ground plane) (im-t-1g36-xx-x) c c -c- 6.01 0.08 .237 .003 (see note 11) 6.98 0.10 .275 .004 (see note 11) 0.96 0.08 .038 .003 (see note 11) 0.25 .010 0.25 .010 c c c -c- c1 c2 'd' 'e' 0.050 .0020 (see note 5) detail 'd' scale 6 : 1 c 0.050 .0020 (see note 5) detail 'e' scale 6 : 1 c c see table 4, sht 2 within row inspection for in process 2 & 3 (carrier not shown for in process 2 inspections) inspection view 1 (see note 12) d d d d d sheet of 0.8mm q-rate right angle socket assembly by: QRF8-XXX-XX-X-RA-GP-XX dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 09/19/2008 5 3 sheet scale: 4:1 revision d f:\dwg\misc\mktg\QRF8-XXX-XX-X-RA-GP-XX-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 free datasheet http://
1.45 0.12 .057 .005 8.84 ref .348 0.00 ref c-288-01-x in process 6 (fill top row) c (see inspection view 2 for assembly orientation and cpc's) d 8.84 ref .348 0.00 ref heat stake top row tails in process 7 (heat stake top row contacts) (see inspection view 2 for assembly orientation and cpc's) d 9.79 ref .386 0.96 ref .038 0.00 ref shear carrier in process 8 (cutoff of carrier) (see inspection view 2 for assembly orientation and cpc's) d see table 4, sht 2 within row r 0.35 .014 r 0.35 .014 90 - 3 + 0 (see note 11) 88 - 1 + 2 (see note 11) 4.121 .1622 (see note 11) 4.31 .170 (see note 4 & 11) 0.60 .024 measure point for c29 in process 5 (form contact c-288-01-x) c c c c 4.87 .192 (ref) 9.79 0.08 .386 .003 (see note 11) 8.84 0.10 .348 .004 (see note 11) 0.96 0.08 .038 .003 (see note 11) 0.25 .010 0.25 .010 c c c -c- c1 c2 'g' 'f' 0.00 - 0.02 + 0.08 .000 - .001 + .003 (see note 4) detail 'g' scale 6 : 1 c 0.00 - 0.02 + 0.08 .000 - .001 + .003 (see note 4) detail 'f' scale 6 : 1 c -0.02 +0.08 c see table 4, sht 2 within row inspection view 2 (see note 12) inspection for in process 6, 7 & 8 (carrier not shown for in process 6 inspections) d d sheet of 0.8mm q-rate right angle socket assembly by: QRF8-XXX-XX-X-RA-GP-XX dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 09/19/2008 5 4 sheet scale: 4:1 revision d f:\dwg\misc\mktg\QRF8-XXX-XX-X-RA-GP-XX-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 free datasheet http://
24.58 0.50 .968 .020 6.99 .275 0.53 0.50 .021 .020 56.15 2.211 (ref) "b" "b" fig 2 -k option (use k-500-300) (only for qrf8-052-02-x-ra-gp-k shown) (some detail removed for clarity) 5.107 .2011 section "b"-"b" scale 2 : 1 31.35 1.234 ref 6.60 .260 ref fig 3 (qrf8-026-02-x-ra-gp shown) (some detail removed for clarity) c l 9.31 .367 (2 plc) 6.51 (2 plc) .256 3.99 .157 (-052 & -078 only, center weld tab) c c c "k" "k" 'h' 'j' 3.99 ref .157 (-052 & -078 only) 6.51 ref .256 9.31 ref .367 "g" ref section "k"-"k" scale 4 : 1 wt-36-xx-t "g" (typ) detail 'h' scale 5 : 1 c "g" (typ) detail 'j' scale 5 : 1 c in process 9 (fill weld tab) (wt-36-xx-t) d sheet of 0.8mm q-rate right angle socket assembly by: QRF8-XXX-XX-X-RA-GP-XX dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 09/19/2008 5 5 sheet scale: 4:1 revision d f:\dwg\misc\mktg\QRF8-XXX-XX-X-RA-GP-XX-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 free datasheet http://
|
