specification control drawing raychem thermofit devices raychem corporation 300 constitution drive menlo park, ca 94025 usa title: soldersleeve*device shield termination low temperature unless otherwise specified dime nsions are in millimeters. inches dimensions are in between brackets. document no.: slt-yx/1yx tolerances: 0.00 n/a 0.0 n/a 0 n/a angles: n/a roughness in micron raychem reserves the right to amend this drawing at any time. users should evaluate the suitability of the product for their application. dcr number: d981081 replaces: slt3x, slt5x, slt6x, slt7x, slt12x & slt14x drawn by: r. mapalo date: 07-06-98 rev.: see table doc issue: 1 scale: none size: a sheet: 1 of 1 if this document is printed it becomes unc ontrolled. check for the latest revision product revisions component di mensions cable dimensions part name l max b min c min e max f min g 0.5(0.020) h 0.5(0.020) d max slt-3x b 17.3 (0.681) 2.7 (0.106) 3.1 (0.122) 3.1 (0.122) 1.4 (0.055) 7 (0.276) 6 (0.236) 2.7 (0.106) SLT-5X b 17.3 (0.681) 4.4 (0.173) 5.0 (0.197) 5.0 (0.197) 2.5 (0.098) 7 (0.276) 6 (0.236) 4.4 (0.173) slt-6x c 20.0 (0.787) 5.9 (0.2.32) 6.4 (0.252) 6.4 (0.252) 3.2 (0.126) 7 (0.276) 6 (0.236) 5.9 (0.2.32) slt-7x c 20.0 (0.787) 7.1 (0.280) 7.6 (0.299) 7.6 (0.299) 4.1 (0.161) 7 (0.276) 6 (0.236) 7.1 (0.280) slt-12x e 31.5 (1.240) 10.8 (0.425) 11.6 (0.457) 11.6 (0.457) 7.3 (0.287) 9.5 (0.374) 8.5 (0.335) 10.8 (0.425) slt-14x h 31.2 (1.228) 13.3 (0.524) 13.8 (0.543) 13.3 (0.524) 8.1 (0.319) 7 (0.276) 6 (0.236) 8.9 (0.350) material 1. insulation sleeve: heat-shrinkable, radiation cross-li nked modified polyvinylidene fluoride. transparent clear. 2. solder preform with flux: solder: type cd18 per ansi j-std-006. flux: type rol1 per ansi j-std-004. color: red. 3. meltable sealing ring: thermally st abilized thermoplastic. color: blue. 4. meltable sealing ring: thermally st abilized thermoplastic. color: clear. application 1. this controlled soldering device is de signed for termination of a tin or silver plated copper shield on a cable having an insulation rated for at least +105 c. 2. temperature range: -55 c to +125 c. 3. for application tooling contact y our local raychem technical service. for best results, prepare the cable as shown: *a trademark of raychem corporation.
|