input parameter conditions min. typ. max. units input voltage range 85 264 vac 120 370 vdc input frequency 47 63 hz input current see model selection guide inrush current 115 vac 10.0 a pk 230 vac 20.0 emi meets cispr pub. 22/fcc class b safety ground leakage current 115 vac 0.1 ma 230 vac 0.3 output parameter conditions min. typ. max. units output voltage see model selection guide output current see model selection guide output voltage accuracy ?.0 % line regulation ?.5 load regulation, see note 1 see model selection guide ripple & noise (20 mhz) 50 mv pk - pk hold-up time 115 vac 20 msec 230 vac 80 temperature coef cient ?.02 %/? short circuit protection continuous (autorecovery) overload protection typ. 110% of output power general parameter conditions min. typ. max. units isolation voltage input to output 3,000 vac input to ground 1,500 output to ground 500 emi/rfi conducted en 55022 level b emc compliance electrostatic discharge (esd) en 61000-4-2 level 3 6kv/8kv rf field susceptibility en61000-4-3 electrical fast transients/bursts on mains en 61000-4-4 level 3 2 kv surge en 61000-4-5 level 3 1kv/2 kv switching frequency 150 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -25 +25 +70 ? case +90 ? storage temperature range -25 +105 ? cooling free air convection (see derating curve) humidity rh, non-condensing 85 % physical case size 2.16 x 1.77 x 0.81 inches (55.0 x 45.0 x 20.5 mm) case material non-conductive black plastic (ul94-v0) weight 4.23 oz (120g) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 200 khours safety standards ul 60950, en 60950 safety approvals ul, cul; file no. e245422 compact, 10w pc mount single, dual & dual iso out ac/dc power supplies key features: 10w output power universal 85-264 vac input en 60950 approved (ul) single, dual & dual iso outputs meets en 55022 b >200 khour mtbf compact pc mount case mpm-10 series electrical speci cations speci cations typical @ +25?, 230 vac input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com www.micropowerdirect.com
model selection guide model number input output 1 (vout 1) output 2 (vout 2) output 3 (vout 3) ef ciency (%, typ) current (a) voltage (vdc) current (a) over volt. protection (vdc) voltage (vdc) current (a) over volt. protection (vdc) voltage (vdc) current (a) 115 vac 230 vac rated load reg. rated load reg. rated load reg. mpm-10s-03 0.23 0.12 3.3 2.00 ?.0% 6.5 70 mpm-10s-05 0.23 0.12 5.0 2.00 ?.0% 6.5 76 mpm-10s-09 0.23 0.12 9.0 1.10 ?.0% 12.0 78 mpm-10s-12 0.23 0.12 12.0 0.90 ?.0% 20.0 80 mpm-10s-15 0.23 0.12 15.0 0.70 ?.0% 20.0 81 mpm-10s-24 0.23 0.12 24.0 0.45 ?.0% 30.0 82 mpm-10d-05 0.23 0.12 +5.0 +1.00 ?.0% 6.5 -5.0 -1.00 ?.0% 6.5 76 mpm-10d-12 0.23 0.12 +12.0 +0.45 ?.0% 20.0 -12.0 -0.45 ?.0% 20.0 80 mpm-10d-15 0.23 0.12 +15.0 +0.35 ?.0% 20.0 -15.0 -0.35 ?.0% 20.0 81 mpm-10d-24 0.23 0.12 +24.0 +0.20 ?.0% 30.0 -24.0 -0.20 ?.0% 30.0 84 mpm-10id-0505 0.23 0.12 5.0 1.80 ?.0% 6.5 5.0 0.20 ?.0% 6.5 75 mpm-10id-0512 0.23 0.12 5.0 1.50 ?.0% 6.5 12.0 0.20 ?.0% 20.0 79 mpm-10id-0515 0.23 0.12 5.0 1.40 ?.0% 6.5 15.0 0.20 ?.0% 20.0 79 mpm-10id-0524 0.23 0.12 5.0 1.00 ?.0% 6.5 24.0 0.20 ?.0% 30.0 81 typical connection mechanical dimensions notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.01 ( 0.25) pin single dual dual iso 1 ac-ground ac-ground ac-ground 2 ac-neutral ac-neutral ac-neutral 3 ac-line ac-line ac-line 4 -vo 1 -vo 2 -vo 1 5 no pin no pin +vo 1 6 no pin common no pin 7 no pin no pin -vo 2 8 +vo 1 +vo 1 +vo 2 pin connections notes: 1. load regulation is measured for an output change of 10% to 90% at nominal input line. for multiple output models, the loads are balanced. 2. the mpm-10 series is speci ed for operation over the wide oper- ating temperature range of -25? to +55? without derating. for operation over +55?, derate the power linearly by 3.75%/? from +55? to +70?. 3. model numbers mpm-10id-05xx are dual isolated units (dual iso). the outputs on these models are isolated from each other. 4. it is recommended that a fuse be used on the input of a power supply for protection. for the mpm-10 series, a 2a/250 vac slow blow should be used. vout c1, c3 c2, c4 fuse tvs 3.3 330 ~ 1,000 f/16v 0.1 f/50v ceramic 2a/ 250 vac slow blow p6ke6.8a 5.0 330 ~ 1,000 f/16v p6ke6.8a 12.0 220 f/25v p6ke16a 15.0 220 f/25v p6ke20a 24.0 120 f/35v p6ke33a typical component values notes: 1. c1 and c3 are high frequency, low resistance electrolytic capacitors. refer to the suppliers speci cations for capacitance/current ratings. 2. voltage derating on all capacitors should be 80% or higher. 3. c2 and c4 eliminate high frequency noise. 4. the tvs is recommended to protect load circuitry in the event of a module failure. micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com www.micropowerdirect.com
|
