snap action switch ss 1 snap action switch ss subminiature snap action switch ? economical, subminiature snap action switch offers long service life (30 million operations minimum) all models are free from overtravel restrictions, permit easy setting wide switching capacity range from microvoltage/current loads (1 ma at 5 vdc to high-capacity loads 10.1 a at 250 vac) standard operating force, low force or super-low force models available rohs compliant ordering information standard type microvoltage/microcurrent load 0.1 a max. (bifurcated crossbar contacts) actuator contact of model pcb terminal soldered terminal tab (#110) terminal straight vertical parallel to left parallel to right pin plunger 25 g ss-01-ed ? ? ss-01-e ss-01-et 50 g ss-01-fd ? ? ss-01-f ss-01-ft 150 g ss-01d ss-01d1 SS-01D2 ss-01 ss-01t hinge lever 8 g ss-01gl-ed ? ? ss-01gl-e ss-01gl-et 16 g ss-01gl-fd ? ? ss-01gl-f ss-01gl-ft 50 g ss-01gld ss-01gld1 ss-01gld2 ss-01gl ss-01glt simulated roller lever 8 g ss-01gl13-ed ? ? ss-01gl13-e ss-01gl13-et 16 g ss-01gl13-fd ? ? ss-01gl13-f ss-01gl13-ft 50 g ss-01gl13d ? ? ss-01gl13 ss-01gl13t formed hinge lever 8 g ? ? ? ss-01gl14-e ss-01gl14-et 16 g ss-01gl14-fd ? ? ss-01gl14-f ? 50 g ss-01gl14d ? ? ss-01gl14 ss-01gl14t hinged roller lever 8 g ss-01gl2-ed ? ? ss-01gl2-e ss-01gl2-et 16 g ss-01gl2-fd ? ? ss-01gl2-f ss-01gl2-ft 50 g ss-01gl2d ? ? ss-01gl2 ss-01gl2t
2 snap action switch ss general-purpose 5 a max. (standard rivet contacts) 10.1 a max. (standard rivet contacts) specifications characteristics note: 1. ss-10 series only. 2. 50,000 operations minimum for the ss-10 series. 3. applies to the pin plunger type (at the pin plunger of the lever type). 4. 10 million operations for the ss-10 series. 5. data shown are of initial value. actuator contact of model pcb terminal soldered terminal tab (#110) terminal straight vertical parallel to left parallel to right pin plunger 50 g ss-5-fd ss-5-fd1 ss-5-fd2 ss-5-f ss-5-ft 150 g ss-5d ss-5d1 ss-5d2 ss-5 ss-5t hinge lever 16 g ss-5gl-fd ss-5gl-fd1 ss-5gl-fd2 ss-5gl-f ss-5gl-ft 50 g ss-5gld ss-5gld1 ss-5gld2 ss-5gl ss-5glt simulated roller lever 16 g ss-5gl13-fd ? ss-5gl13-fd2 ss-5gl13-f ss-5gl13-ft 50 g ss-5gl13d ss-5gl13d1 ss-5gl13d2 ss-5gl13 ss-5gl13t formed hinge lever 16 g ss-5gl14-fd ss-5gl14-fd1 ? ss-5gl14-f ss-5gl14-ft 50 g ss-5gl14d ss-5gl14d1 ss-5gl14d2 ss-5gl14 ss-5gl14t hinge roller lever 16 g ss-5gl2-fd ss-5gl2-fd1 ss-5gl2-fd2 ss-5gl2-f ss-5gl2-ft 50 g ss-5gl2d ss-5gl2d1 ss-5gl2d2 ss-5gl2 ss-5gl2t actuator contact of model pcb terminal soldered terminal tab (#110) terminal straight vertical parallel to left parallel to right pin plunger 150 g ss-10d ? ? ss-10 ss-10t hinge lever 50 g ss-10gld ? ? ss-10gl ss-10glt simulated roller lever 50 g ss-10gl13d ? ? ss-10gl13 ss-10gl13t formed hinge lever 50 g ???ss-10gl14? hinge roller lever 50 g ss-10gl2d ? ? ss-10gl2 ss-10gl2t switch type general-purpose operating speed (see note 3) 0.1 mm to 1 m/second (0.004 to 39.4 in/second) operating frequency mechanical 400 operations per minute (pin plunger actuator type) electrical 60 operations per minute (pin plunger actuator type) insulation resistance 100 m ? at 500 vdc dielectric strength crossbar contact type 600 vac, 50/60 hz for 1 minute (see note 1) others 1,000 vac, 50/60 hz for 1 minute between terminals of same polarity 1,500 vac, 50/60 hz for 1 minute between current-carrying parts and ground and between each terminal and noncurrent-carrying metal parts vibration malfunction durability 10 to 55 hz, 1.5 mm double amplitude shock mechanical durability low-of type: 50 0 m/s 2 min. (approx. 50 g) others: 1,00 0 m/s 2 min. (approx. 100 g) malfunction durability standard type: 300 m/s 2 min. (approx. 30 g) low-of type: 200 m/s 2 min. (approx. 20 g) lever type at ttp: contact gap, 1 ms max. ambient temperature operating -25 to 85 c with no icing humidity 85% rh max. service life mechanical 30 million operations minimum (ot: rated value) (see note 4) electrical 200,000 operations minimum (rated load) (see note 2) weight approx. 1.6 g pin plunger type
snap action switch ss 3 operating characteristics ratings microvoltage/microcurrent load type characteristics part number ss-01-e ss-01-f ss-5-f ss-01 ss-5 ss-10 ss-01gl-e of max. 25 g 50 g 150 g 150 g 8 g rf min. 2 g 4 g 25 g 25 g 1 g pt max. 0.5 mm (0.020 in) 0.5 mm (0.020 in) 0.5 mm (0.020 in) 0.6 mm (0.024 in) 1.2 mm (0.047 in) ot min. 0.5 mm (0.020 in) 0.5 mm (0.020 in) 0.5 mm (0.020 in) 0.4 mm (0.016 in) 0.8 mm (0.032 in) md max. 0.1 mm (0.004 in) 0.1 mm (0.004 in) 0.1 mm (0.004 in) 0.12 mm (0.005 in) 13.6 mm (0.535 in) op 8.4 0.5 mm (0.331 0.020 in) 8.4 0.5 mm (0.331 0.020 in) 8.4 0.5 mm (0.331 0.020 in) 8.4 0.5 mm (0.331 0.020 in) 8.8 0.8 mm (0.346 0.032 in) characteristics part number ss-01gl-f ss-5gl-f ss-01gl ss-5gl ss-10gl ss-10gl13-e ss-10gl13-f ss-5gl13-f of max. 16 g50 g50 g8 g 16 g rf min. 2 g6 g6 g1 g2 g pt max. 1.2 mm (0.047 in) 1.2 mm (0.047 in) 1.0 mm (0.039 in) 1.2 mm (0.047 in) 1.2 mm (0.047 in) ot min. 0.8 mm (0.032 in) 0.8 mm (0.032 in) 1.0 mm (0.039 in) 0.8 mm (0.032 in) 0.8 mm (0.032 in) md max. 13.6 mm (0.535 in) 13.6 mm (0.535 in) 13.6 mm (0.535 in) 15.5 mm (0.610 in) 15.5 mm (0.610 in) op 8.8 0.8 mm (0.346 0.032 in) 8.8 0.8 mm (0.346 0.032 in) 8.8 0.8 mm (0.346 0.032 in) 10.7 0.8 mm (0.421 0.032 in) 10.7 0.8 mm (0.421 0.032 in) characteristics part number ss-01gl13 ss-5gl13 ss-10gl13 ss-01gl14-e ss-01gl14-f ss-5gl14-f ss-01gl14 ss-5gl14 of max. 50 g50 g8 g 16 g50 g rf min. 6 g6 g1 g2 g6 g pt max. 1.2 mm (0.047 in) 1.0 mm (0.039 in) 1.2 mm (0.047 in) 1.2 mm (0.047 in) 1.2 mm (0.047 in) ot min. 0.8 mm (0.032 in) 1.0 mm (0.039 in) 0.8 mm (0.032 in) 0.8 mm (0.032 in) 0.8 mm (0.032 in) md max. 15.5 mm (0.610 in) 15.5 mm (0.610 in) 14.9 mm (0.587 in) 14.9 mm (0.587 in) 14.9 mm (0.587 in) op 10.7 0.8 mm (0.421 0.032 in) 10.7 0.8 mm (0.421 0.032 in) 10.1 0.8 mm (0.398 0.032 in) 10.1 0.8 mm (0.398 0.032 in) 10.1 0.8 mm (0.398 0.032 in) characteristics part number ss-10gl14 ss-01gl2-e ss-01gl2-f ss-5gl2-f ss-01gl2 ss-5gl2 ss-10gl2 of max. 50 g 8 g 16 g 50 g 50 g rf min. 6 g1 g2 g6 g6 g pt max. 1.0 mm (0.039 in) 1.2 mm (0.047 in) 1.2 mm (0.047 in) 1.2 mm (0.047 in) 1.0 mm (0.039 in) ot min. 1.0 mm (0.039 in) 0.8 mm (0.032 in) 0.8 mm (0.032 in) 0.8 mm (0.032 in) 1.0 mm (0.039 in) md max. 14.9 mm (0.587 in) 19.3 mm (0.760 in) 19.3 mm (0.760 in) 19.3 mm (0.760 in) 19.3 mm (0.760 in) op 10.1 0.8 mm (0.398 0.032 in) 14.5 0.8 mm (0.571 0.032 in) 14.5 0.8 mm (0.571 0.032 in) 14.5 0.8 mm (0.571 0.032 in) 14.5 0.8 mm (0.571 0.032 in) contact form general purpose/resistive load bifurcated crossbar contacts nc no 125 vac 0.1 a 0.1 a 30 vdc 0.1 a 0.1 a inrush current 1 a max. 1 a max.
4 snap action switch ss standard type general purpose note: 1. the above current ratings are the values of the steady-state current. 2. inductive load has a power factor of 0.4 min. (ac) and a time constant of 7 milliseconds max. (dc). the inductive load applicab le to the ss-10 series must have a power factor of 0.75 min. 3. lamp load has an inrush current of 10 times the steady-state current 4. motor load has an inrush current of 6 times the steady-state current. 5. if the switch is used in a dc circuit and is subjected to inrush current or surge, connect a surge suppressor across the switch . contact resistance (m ? max., initial) contact form sealed lead wire terminal models have color coded leads. * consult omron for spst-nc and spst-no contact form types ordering information. approvals ul (file no. e41515), csa (file no. lr21642), ss-5/ss-10: en conforms 61058-1 vde (file no. 5861-3221) semko (file nos. 43-8614026/43-891609) note: the rated values approved by each of the safety standards (e.g. ul, csa) may be different from the performance characteristics individually defined in this catalog. switch series: rivet contacts resistive load lamp load inductive load motor load ss-5 ss-10 ss-5 and ss-10 ss-5 and ss-10 ss-5 and ss-10 contact form nc no nc no nc no nc no nc no 125 vac 5 a 5 a 10.1 a 10.1 a 1.5 a 0.7 a 3 a 3 a 2.5 a 1.3 a 250 vac 3 a 3 a 10.1 a 10.1 a 1 a 0.5 a 2 a 2 a 1.5 a 0.8 a 8 vdc 5 a 5 a 10.1 a 10.1 a 2 a 2 a 5 a 4 a 3 a 3 a 14 vdc 5 a 5 a 10.1 a 10.1 a 2 a 2 a 4 a 4 a 3 a 3 a 30 vdc 4 a4 a4 a4 a2 a2 a3 a3 a3 a3 a 125 vdc 0.4 a 0.4 a 0.4 a 0.4 a 0.05 a 0.05 a 0.4 a 0.4 a 0.05 a 0.05 a 250 vdc 0.2 a 0.2 a 0.2 a 0.2 a 0.03 a 0.03 a 0.2 a 0.2 a 0.03 a 0.03 a inrush current 20 a max. 10 a max. 20 a max. 15 a max. (both non-inductive and inductive loads) contact rating: ss-01 @ ss-5 @ ss-10 @ 0.1 a 3 a or 5 a 10.1 a normal operating force models (ss- @ ) 50 m ? 30 m ? 30 m ? low operating force models (ss- @ -f) 100 m ? 50 m ? ? super-low operating force models (ss- @ -e) 150 m ? ?? lead wire models (all of types) 100 m ? 50 m ? ? spdt (common throughout the series) spst-nc* (standard models rated at 0.1 to 0.5 a) spst-no* (standard models rated at 0.1 to 5 a) type rating ss-10 series general-purpose type 10.1 a, 250 vac ss-5 series general-purpose type 5 a, 125 v, 3 a 250 vac ss-01 series super-low force type 0.1 a, 125 vac, 30 vdc type rating ss-5 series general-purpose type 5 a, 250 vac type rating ss-10 series general-purpose type 10 a, 250 vac ss-5 series general-purpose type 5 a, 250 vac
snap action switch ss 5 engineering data mechanical service life standard type (ss-5, ss-10 series) electrical service life standard type (ss-5 series) dimensions unit: mm (inch) pin plunger ss-01 (-e, -f) ss-5 (-f) ss-10 hinge lever ss-01gl (-e, -f) ss-5gl (-f) ss-10gl
6 snap action switch ss note: 1. unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. 2. straight vertical pcb terminal models are shown above. soldered terminal, tab (#110) terminal, lead wire terminal, pcb terminal parallel to left and pcb terminal parallel to right are shown in the terminals section. note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. mounting holes standard types mounting holes below are for reference only note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. s imulated roller lever ss-01gl13 (-e, -f) ss-5gl13 (-f) ss-10gl13 formed hinge lever ss-01gl14 (-e, -f) ss-5gl14 (-f) ss-10gl14 hinge roller lever ss-01gl2 (-e, -f) ss-5gl2 (-f) ss-10gl2
snap action switch ss 7 unit: mm (inch) terminals general-purpose type note: thickness of all the terminals is 0.5 mm. pcb terminal, straight vertical (d) pcb terminal, parallel to left (d1) pcb terminal, parallel to right (d2) soldered terminal (blank) quick-connect tab (#110) terminal (t)
8 snap action switch ss omron electronic components, llc terms and conditions of sales 1. definitions : the words used herein are defined as follows. (a) terms: these terms and conditions (b) seller: omron electronic components llc and its subsidiaries (c) buyer: the buyer of products, including any end user in section iii through vi (d) products: products and/or services of seller (e) including: including without limitation 2. offer; acceptance: these terms are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of products by seller. seller hereby objects to any terms proposed in buyer's purchase order or other documents which are inconsistent with, or in addition to, these te r ms . 3. distributor : any distributor shall inform its customer of the contents after and including section iii of these terms. 1. prices; payment : all prices stated are current, subject to change without notice by seller. buyer agrees to pay the price in effect at time of shipment. payments for products received are due net 30 days unless otherwise stated in the invoice. buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. 2. discounts : cash discounts, if any, will apply only on the net amount of invoices sent to buyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to seller's payment terms and (b) buyer has no past due amounts owing to seller. 3. interest : seller, at its option, may charge buyer 1.5% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 4. orders : seller will accept no order less than 200 u.s. dollars net billing. 5. currencies : if the prices quoted herein are in a currency other than u.s. dollars, buyer shall make remittance to seller at the then current exchange rate most favorable to seller; provided that if remittance is not made when due, buyer will convert the amount to u.s. dollars at the then current exchange rate most favorable to seller available during the period between the due date and the date remittance is actually made. 6. governmental approvals : buyer shall be responsible for all costs involved in obtaining any government approvals regarding the importation or sale of the products. 7. taxes : all taxes, duties and other governmental charges (other than general real property and income taxes) , including any interest or penalties thereon, imposed directly or indirectly on seller or required to be collected directly or indirectly by seller for the manufacture, production, sale, delivery, importation, consumption or use of the products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by buyer to seller. 8. financial : if the financial position of buyer at any time becomes unsatisfactory to seller, seller reserves the right to stop shipments or require satisfactory security or payment in advance. if buyer fails to make payment or otherwise comply with these terms or any related agreement, seller may (without liability and in addition to other remedies) cancel any unshipped portion of products sold hereunder and stop any products in transit until buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by buyer. buyer shall in any event remain liable for all unpaid accounts. 9. cancellation; etc: orders are not subject to rescheduling or cancellation unless buyer indemnifies seller fully against all costs or expenses arising in connection therewith. 10. force majeure : seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. shipping; delivery: unless otherwise expressly agreed in writing by seller: (a) all sales and shipments of products shall be fob shipping point (unless otherwise stated in writing by seller) , at which point title to and all risk of loss of the products shall pass from seller to buyer, provided that seller shall retain a security interest in the products until the full purchase price is paid by buyer; (b) delivery and shipping dates are estimates only; and (c) seller will package products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. claims: any claim by buyer against seller for shortage or damage to the products occurring before delivery to the carrier must be presented in detail in writing to seller within 30 days of receipt of shipment. 1. suitability: it is the buyer?s sole respoinsibility to ensure that any omron product is fit and sufficient for use in a motorized vehicle application. buyer shall be solely responsible for determining appropriateness of the particular product with respect to the buyer?s application including (a) electrical or electronic components, (b) circuits, (c) system assemblies, (d) end product, (e) system, (f) materials or substances or (g) operating environment. buyer acknowledges that it alone has determined that the products will meet their requirements of the intended use in all cases. buyer must know and observe all prohibitions of use applicable to the product/s. 2. use with attention: the followings are some examples of applications for which particular attention must be given. this is not intended to be an exhaustive list of all possible use of any product, nor to imply that any use listed may be suitable for any product: (a) outdoor use, use involving potential chemical contamination or electrical interference. (b) use in consumer products or any use in significant quantities. (c) energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (d) systems, machines, and equipment that could present a risk to life or property. 3. prohibited use: never use the product for an application involving serious risk to life or property without ensuring that the system as a whole has been designed to address the risks, and that the product is properly rated and installed for the intended use within the overall equipment or system. 4. motorized vehicle application: use of any product/s for a motorized vehicle application must be expressly stated in the specification by seller. 5. programmable products: seller shall not be responsible for the buyer's programming of a programmable product. 1. warranty : seller's exclusive warranty is that the products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by seller (or such other period expressed in writing by seller). seller makes no warranty or representation, express or implied, about all other warranties, non-infringement, merchantability or fitness for a particular purpose of the products. 2. buyer remedy : seller's sole obligation hereunder shall be to replace (in the form originally shipped with buyer responsible for labor charges for removal or replacement thereof) the non-complying product or, at seller's election, to repay or credit buyer an amount equal to the purchase price of the product; provided that there shall be no liability for seller or its affiliates unless seller's analysis confirms that the products were handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. return of any products by buyer must be approved in writing by seller before shipment. 3. limitation on liability : seller and its affiliates shall not be liable for special, indirect, incidental or consequential damages, loss of profits or production or commercial loss in any way connected with the products, whether such claim is based in contract, warranty, negligence or strict liability. further, in no event shall liability of seller or its affilitates exceed the individual price of the product on which liability is asserted. 4. indemnities : buyer shall indemnify and hold harmless seller, its affiliates and its employees from and against all liabilities, losses, claims, costs and expenses ( including attorney's fees and expenses ) related to any claim, investigation, litigation or proceeding ( whether or not seller is a party ) which arises or is alleged to arise from buyer's acts or omissions under these terms or in any way with respect to the products. 1. intellectual property : the intellectual property embodied in the products is the exclusive property of seller and its affiliates and buyer shall not attempt to duplicate it in any way without the written permission of seller. buyer (at its own expense) shall indemnify and hold harmless seller and defend or settle any action brought against seller to the extent that it is based on a claim that any product made to buyer specifications infringed intellectual property rights of another party. 2. property; confidentiality : notwithstanding any charges to buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of seller. all information and materials supplied by seller to buyer relating to the products are confidential and proprietary, and buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 3. performance data : performance data is provided as a guide in determining suitability and does not constitute a warranty. it may represent the result of seller's test conditions, and the users must correlate it to actual application requirements. 4. change in specifications : product specifications and description may be changed at any time based on improvements or other reasons. it is seller?s practice to change part numbers when published ratings or features are changed, or when significant engineering changes are made. however, some specifications of the product may be changed without any notice. 5. errors and omissions : the information on seller?s website or in other documentation has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 6. export controls : buyer shall comply with all applicable laws, regulations and licenses regarding (a) export of the products or information provided by seller; (b) sale of products to forbidden or other proscribed persons or organizations; (c)disclosure to non-citizens of regulated technology or information. 1. waiver : no failure or delay by seller in exercising any right and no course of dealing between buyer and seller shall operate as a waiver of rights by seller. 2. assignment : buyer may not assign its rights hereunder without seller's written consent. 3. law : these terms are governed by illinois law (without regard to conflict of laws) . federal and state courts in illinois have exclusive jurisdiction for any dispute hereunder. 4. amendment : these terms constitute the entire agreement between buyer and seller relating to the products, and no provision may be changed or waived unless in writing signed by the parties. 5. severability : if any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. i. general ii. sales iii. pre cautions iv. warranty and limitation v. information; etc. vi. miscellaneous
snap action switch ss 9 certain precautions on specifications and use 1. suitability for use . seller shall not be responsible for conformity with any stan- dards, codes or regulations which apply to the combination of the product in buyer's application or use of the product. at buyer's request, seller will pro- vide applicable third party certification documents identifying ratings and limi- tations of use which apply to the product. this information by itself is not sufficient for a complete determination of the suitability of the product in com- bination with the end product, machine, system, or other application or use. buyer shall be solely responsible for determining appropriateness of the par- ticular product with respect to buyer's application, product or system. buyer shall take application responsibility in all cases but the following is a non- exhaustive list of applications for which particular attention must be given: (i) outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii) use in consumer products or any use in significant quantities. (iv) systems, machines and equipment that could present a risk to life or property. please know and observe all prohibitions of use applicable to this product. never use the product for an application involving serious risk to life or property without ensuring that the system as a whole has been designed to a ddress the risks, and that the omron product is properly rated and installed for the intended use within the overall equipment or system. 2. programmable products . seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. performance data . performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a war- ranty. it may represent the result of seller's test conditions, and the users must correlate it to actual application requirements. actual performance is subject to seller's warranty and limitations of liability. 4. change in specifications . product specifications and accessories may be changed at any time based on improvements and other reasons. it is our prac- tice to change part numbers when published ratings or features are changed, or when significant construction changes are made. however, some specifica- tions of the product may be changed without any notice. when in doubt, spe- cial part numbers may be assigned to fix or establish key specifications fo r your application. please consult with your seller representative at any time to confirm actual specifications of purchased product. 5. errors and omissions . the information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. 6. rohs compliance . where indicated, our products currently comply, to the best of our knowledge as of the date of this publication, with the requirements of the european union's directive on the restriction of certain hazardous substances ("rohs"), although the requirements of rohs do not take effect until july 2006. these requirements may be subject to change. please consult our website for current information.
10 snap action switch ss omron on-line global - http://www.omron.com usa - http://www.components.omron.com cat. no. j01c-e-01 printed in usa omron electronic components llc 55 e. commerce drive, suite b schaumburg, il 60173 847-882-2288 01/07 specifications subject to change without notice complete ?terms and conditions of sale? for product purchase and use are on omron?s website at http://www.components.omron.com ? under the ?about us? tab, in the legal matters section. all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.03937. to convert grams into ounces, multiply by 0.03527.
|
