designed & dimensioned in millimeters[inches] recommended cable stripping do not scale from this print pin (bnc7-pin-002-m) sub asssembly (sub-bnc7-p-c-n-st-ca3) fig. 1 (BNC7-P-C-MN-ST-CA3 shown) outer ferrule (sma-fer-001-n) 12.1 .48 3.2 .13 5.7 .22 gender -ca3: cable (rg179) -st: straight orientation termination plating specification -c: cable type -p: plug -mn: medium gold/nickel (see note 7) (sma-fer-001-n) (bnc7-pin-002-m) (sub-bnc7-p-c-n-st-ca3) bnc7-p-c-xx-st-ca3 c sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: bnc str, plug rg179-75 ohm by: bnc7-p-c-xx-st-ca3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing g.herman 06/19/2008 3 1 sheet scale: 2:1 f:\dwg\misc\mktg\bnc7-p-c-xx-st-ca3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 notes: 1. represents a critical dimension. 2. center contact pushout force: 26.69 n [6 lb] min. 3. see sheet 3 for termination information. 4. components to be shipped unassembled. 5. sample orders: to be packaged in individual kit form, production orders: each component to be bulk packaged. 6. rohs compliant. 7. plating: -n: 0.00254[0.000100] (min) nickel -m: 0.00025[0.000010] (min) gold over 0.00127[0.000050] (min) nickel revision d
0.40 .016 12.65 .498 1.35 .053 14.50 .571 13.80 .543 2.70 .106 21.70 .854 3.90 .154 (ref) 3.20 .126 (ref) 9.50 (ref) .374 scale: 4:1 scale: 4:1 sheet of bnc str, plug rg179-75 ohm by: bnc7-p-c-xx-st-ca3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing g.herman 06/19/2008 3 2 sheet scale: 2:1 revision d f:\dwg\misc\mktg\bnc7-p-c-xx-st-ca3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
3.2 .13 5.7 .22 12.1 .48 rg179 cable strip and tin inner conductor add heat shrink tube and ferrule flare shield solder signal pin add sub-bnc7-p-c-x-st-ca3 crimp ferrule (use rf crimp hand tool #cat-ht-126667-21) apply heat shrink tube 20.0 2.5 .79 .10 outer ferrule (sma-fer-001-n) (shown) heat shrink tube 2.70 .106 (min. flared id) 0.10 gap max. .004 pin (bnc7-pin-002-m) (shown) sub assembly (sub-bnc7-p-c-n-st-ca3) 3.25 hex crimp .128 9.75 max .384 c2 c3 20.00 ref .787 0.16 - 0.03 + 0.17 .006 - .001 + .007 to center contact detail 'a' scale 2.5 : 1 c1 sheet of bnc str, plug rg179-75 ohm by: bnc7-p-c-xx-st-ca3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing g.herman 06/19/2008 3 3 sheet scale: 1.25:1 revision d f:\dwg\misc\mktg\bnc7-p-c-xx-st-ca3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
