View MGA-30889-BLKG_7101592.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mga-30889 40mhz - 2600mhz flat gain high linearity gain block data sheet attention: observe precautions for handling electrostatic sensitive devices. esd machine model = 50 v esd human body model = 400 v refer to avago application note a004r: electrostatic discharge, damage and control. description avago technologies mga-30889 is a broadband, fat gain, high linearity gain block mmic amplifer achieved through the use of avago technologies proprietary 0.25um gaas enhancement-mode phemt process. the device required simple dc biasing components to achieve wide bandwidth performance. the temperature compensated internal bias circuit provides stable current over temperature and process threshold voltage variation. the mga-30889 is housed inside a low cost rohs compliant sot89 industry standard smt package (4.5 x 4.1 x 1.5 mm). component image notes: package marking provides orientation and identifcation 8g = device code x = month of manufacture features ? flat gain 15db +/-0.25db, 40mhz to 2600mhz ? high linearity ? built in temperature compensated internal bias circuitry ? no rf matching components required ? gaas e-phemt technology [1] ? standard sot89 package ? single, fixed 5v supply ? excellent uniformity in product specifcations ? msl-2 and lead-free halogen free ? high mttf for base station application specifcations 900mhz; 5v, 65ma (typical) ? 15.5 db gain ? 38 dbm output ip3 ? 1.9 db noise figure ? 20 dbm output power at 1db gain compression 1950mhz, 5v, 65ma (typical) ? 15.7 db gain ? 36 dbm output ip3 ? 2 db noise figure ? 20.3 dbm output power at 1db gain compression applications ? if amplifer, rf driver amplifer ? general purpose gain block note: 1. enhancement mode technology employs positive gate voltage, thereby eliminating the need of negative gate voltage associated with conventional depletion mode devices. 8gx top view rfin gnd rfout #1 #2 #3 bottom view rfout gnd rfin #3 #2 #1
2 absolute maximum rating [1] t a =25 c symbol parameter units absolute max. v dd,max device voltage, rf output to ground v 5.5 p in,max cw rf input power dbm 20 p diss total power dissipation [3] w 0.47 t j,max junction temperature c 150 t stg storage temperature c -65 to 150 thermal resistance thermal resistance [2] jc = 76c/w (vdd = 5 v, ids = 57.5 ma, tc = 85c) notes: 1. operation of this device in excess of any of these limits may cause permanent damage. 2. thermal resistance measured using infrared measurement technique. 3. this is limited by maximum vdd and ids. derate 13.2 mw/c for tc >114c. product consistency distribution charts [1, 2] figure 1. ids, lsl=53ma , nominal=65ma, usl=77ma figure 2. gain, lsl=14.6db, nominal=15.7db, usl=16.8db figure 5. nf, nominal=2db, usl=2.7db figure 3. oip3, lsl=33dbm, nominal=36dbm figure 4. p1db, lsl=19.2dbm, nominal=20.3dbm 1.6 1.8 1.9 1.7 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 usl 60 70 usl lsl 33 34 35 36 38 37 39 lsl 14.5 15 15.5 16 16.5 usl lsl 19.2 19.6 20 20.4 20.8 lsl notes: 1. distribution data sample size is 3000 samples taken from 3 diferent wafer lots. future wafers allocated to this product may have nominal values anywhere between the upper and lower limits. 2. measurements were made on a characterization test board, which represents a trade-of between optimal oip3, gain and p1db. circuit trace losses have not been de-embedded from measurements above.
3 electrical specifcations [1] t a = 25c, vdd =5v symbol parameter and test condition frequency units min. typ. max. ids quiescent current n/a ma 53 65 77 gain gain 40mhz 900mhz 1950mhz db 14.6 15.9 15.5 15.7 16.8 oip3 [2] output third order intercept point 40mhz 900mhz 1950mhz dbm 33 37 38 36 C nf noise figure 40mhz 900mhz 1950mhz db C 2.0 1.9 2.0 2.7 s11 input return loss, 50 ? source 40mhz 900mhz 1950mhz db -16 -17 -13 s22 output return loss, 50 ? load 40mhz 900mhz 1950mhz db -16 -16.5 -13 s12 reverse isolation 40mhz 900mhz 1950mhz db -17 -17 -22 op1db output power at 1db gain compression 40mhz 900mhz 1950mhz dbm 19.2 21 20 20 C notes: 1. measurements obtained using demo board described in figure 30 and 31. 40mhz data was taken with 40mhz - 2ghz application test circuit, 900mhz data with 0.2ghz C 2.6ghz application test circuit and 1.95ghz data with 1.5ghz - 2.6ghz application test circuit respectively. 2. oip3 test condition: f rf1 - f rf2 = 10mhz with input power of -15dbm per tone measured at worse side band. 3. use proper bias, heat sink and de-rating to ensure maximum channel temperature is not exceeded. see absolute maximum ratings and application note (if applicable) for more details.
4 typical performance (40mhz - 2ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 1. figure 6. ids over temperature figure 7. gain over frequency and temperature figure 8. oip3 over frequency and temperature figure 9. p1db over frequency and temperature figure 10. s11 over frequency and temperature figure 11. s22 over frequency and temperature 50 60 70 80 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 temperature (c) ids (ma) 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) oip3 (dbm) -30 -25 -20 -15 -10 -5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) s11 (db) 10 11 12 13 14 15 16 17 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) gain (db) 15 16 17 18 19 20 21 22 23 24 25 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) p1db(dbm) -30 -25 -20 -15 -10 -5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) s22 (db) 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c
5 figure 12. s12 over frequency and temperature figure 13. noise figure over frequency and temperature typical performance (0.2ghz - 2.6ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 2. figure 14. ids over temperature figure 15. gain over frequency and temperature figure 16. oip3 over frequency and temperature figure 17. p1db over frequency and temperature typical performance (40mhz - 2ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 1. -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) s12 (db) 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 frequency (ghz) nf(db) 85c 25c -40c 85c 25c -40c 50 60 70 80 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 temperature (c) ids (ma) 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) oip3 (dbm) 10 11 12 13 14 15 16 17 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) gain (db) 15 16 17 18 19 20 21 22 23 24 25 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) p1db(dbm) 85c 25c -40c 85c 25c -40c 85c 25c -40c
6 figure 18. s11 over frequency and temperature figure 19. s22 over frequency and temperature figure 20. s12 over frequency and temperature figure 21. noise figure over frequency and temperature figure 22. ids over temperature figure 23. gain over frequency and temperature typical performance (1.5ghz - 2.6ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 3. typical performance (0.2ghz - 2.6ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 2. -30 -25 -20 -15 -10 -5 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s11 (db) -30 -25 -20 -15 -10 -5 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s22 (db) -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s12 (db) 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) nf(db) 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c 50 60 70 80 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 temperature (c) ids (ma) 10 11 12 13 14 15 16 17 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) gain (db) 85c 25c -40c
7 figure 24. oip3 over frequency and temperature figure 25. p1db over frequency and temperature figure 26. s11 over frequency and temperature figure 27. s22 over frequency and temperature figure 28. s12 over frequency and temperature figure 29. noise figure over frequency and temperature typical performance (1.5ghz - 2.6ghz) t a = 25c, vdd =5v, input signal=cw. application test circuit is shown in figure 30 and table 3. 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) oip3 (dbm) -30 -25 -20 -15 -10 -5 0 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s11 (db) 15 16 17 18 19 20 21 22 23 24 25 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) p1db(dbm) -30 -25 -20 -15 -10 -5 0 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s22 (db) -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) s12 (db) 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 frequency (ghz) nf(db) 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c 85c 25c -40c
8 application schematic components table and demo board figure 30. application schematic figure 31. demo board layout rfout l1/l2 vdd vdd c8 c1/ c4 c3/ c6 c2/ c5 top view c7 rfin 3 1 2 rfin gnd rfout note: l1, c1, c2, c3 is for bom 0.2-2.6ghz and 1.5-2.6ghz l2, c4, c5, c6 is for bom 40mhz-2ghz C recommended pcb material is 10 mils rogers ro4350, with fr4 backing for mechanical strength. C suggested component values may vary according to layout and pcb material.
9 demo board part list table 1. 40mhz - 2ghz application schematic components circuit symbol size value part number description l2 0805 820nh llq2012-series (toko) wire wound chip inductor c4 0402 100pf grm1555c1h101jz01 (murata) ceramic chip capacitor c5 0402 0.1uf grm155r71c104ka88d (murata) ceramic chip capacitor c6 0805 2.2uf grm21br61e225ka12l (murata) ceramic chip capacitor c7 0402 0.1uf grm155r71c104ka88d (murata) ceramic chip capacitor c8 0402 0.1uf grm155r71c104ka88d (murata) ceramic chip capacitor table 2. 0.2ghz - 2.6ghz application schematic components circuit symbol size value part number description l1 0603 100nh llq1608-fr10 (toko) wire wound chip inductor c1 0402 10pf grm1555c1h100jz01 (murata) ceramic chip capacitor c2 0402 0.1uf grm155r71c104ka88d (murata) ceramic chip capacitor c3 0805 2.2uf grm21br61e225ka12l (murata) ceramic chip capacitor c7 0402 100pf grm1555c1h101jz01 (murata) ceramic chip capacitor c8 0402 100pf grm1555c1h101jz01 (murata) ceramic chip capacitor table 3. 1.5ghz - 2.6ghz application schematic components circuit symbol size value part number description l1 0402 5.6nh ll1005-fhl5n6 (toko) mlc inductor c1 0402 100pf grm1555c1h101jz01 (murata) ceramic chip capacitor c2 0402 0.1uf grm155r71c104ka88d (murata) ceramic chip capacitor c3 0805 2.2uf grm21br61e225ka12l (murata) ceramic chip capacitor c7 0402 20pf grm1555c1h200jz01 (murata) ceramic chip capacitor c8 0402 20pf grm1555c1h200jz01 (murata) ceramic chip capacitor
10 test circuit for s-parameter and noise parameter figure 32. s-parameter and noise parameter test circuit 3 1 2 rfin gnd vdd rfout top view port1 port2 / bias tee
11 typical s-parameter (vdd = 5v, t a = 25c, 50 ohm) freq (ghz) s11 (db) s11 (ang) s21 (db) s21 (ang) s12 (db) s12 (ang) s22 (db) s22 (ang) 0.04 -17.04 -88.23 16.16 167.09 -20.08 6.83 -14.55 -138.35 0.1 -23.82 -99.63 15.83 170.40 -20.02 -1.16 -15.92 -163.34 0.2 -27.02 -106.63 15.78 167.69 -20.03 -7.14 -16.38 -173.98 0.3 -26.83 -116.89 15.78 163.41 -20.05 -12.02 -16.45 -179.28 0.4 -24.42 -127.93 15.78 158.71 -20.08 -16.72 -16.24 176.99 0.5 -22.60 -130.33 15.79 153.85 -20.12 -21.30 -16.34 177.06 0.6 -21.35 -134.41 15.81 148.88 -20.16 -25.84 -16.37 178.09 0.7 -20.18 -140.06 15.83 143.85 -20.21 -30.36 -16.39 178.81 0.8 -19.10 -146.29 15.85 138.73 -20.27 -34.85 -16.40 178.64 0.9 -18.13 -152.78 15.88 133.58 -20.34 -39.29 -16.35 177.88 1 -17.42 -160.67 15.91 128.38 -20.42 -43.88 -16.16 177.12 1.1 -16.72 -166.54 15.96 123.11 -20.50 -48.37 -16.54 175.97 1.2 -16.21 -176.41 16.00 117.79 -20.60 -52.85 -16.29 174.49 1.3 -15.66 173.51 16.03 112.37 -20.70 -57.37 -16.03 172.05 1.4 -15.09 162.73 16.07 106.92 -20.82 -61.94 -15.76 168.90 1.5 -14.41 151.57 16.10 101.34 -20.96 -66.51 -15.42 164.84 1.6 -13.67 140.49 16.12 95.64 -21.12 -71.09 -15.11 160.22 1.7 -12.91 130.11 16.13 89.95 -21.29 -75.69 -14.81 155.66 1.8 -12.12 120.06 16.13 84.16 -21.47 -80.32 -14.56 150.71 1.9 -11.34 110.67 16.12 78.29 -21.68 -84.88 -14.33 145.47 2 -10.60 101.66 16.10 72.45 -21.90 -89.37 -14.14 140.05 2.1 -9.89 93.15 16.06 66.53 -22.14 -93.79 -13.96 134.67 2.2 -9.25 84.93 16.01 60.60 -22.41 -98.15 -13.84 129.50 2.3 -8.70 77.25 15.96 54.75 -22.69 -102.42 -13.80 124.63 2.4 -8.17 69.77 15.88 48.83 -22.98 -106.71 -13.80 119.72 2.5 -7.72 62.66 15.80 43.02 -23.28 -110.71 -13.84 115.08 2.6 -7.32 55.78 15.70 37.21 -23.59 -114.68 -13.93 110.60 2.7 -6.97 48.95 15.61 31.35 -23.93 -118.51 -14.07 106.56 2.8 -6.68 42.26 15.51 25.64 -24.25 -122.20 -14.28 102.99 2.9 -6.44 35.55 15.40 19.84 -24.57 -125.87 -14.56 99.69 3 -6.23 28.95 15.30 14.15 -24.89 -129.40 -14.95 96.77 4 -4.89 -49.49 13.83 -45.76 -28.13 -161.64 -23.03 97.19 5 -2.59 -116.16 10.78 -101.46 -31.11 175.49 -25.89 -152.28 6 -2.03 -163.08 8.27 -146.84 -31.55 155.55 -32.05 -167.12 7 -2.13 126.91 6.05 159.94 -30.84 116.80 -20.70 67.94 8 -1.18 63.71 1.85 107.76 -32.11 72.53 -15.41 31.66 9 -0.90 21.52 -2.15 65.10 -33.21 35.83 -13.70 -6.02 10 -0.96 -35.93 -6.31 19.48 -34.36 -2.85 -11.83 -41.95 11 -0.57 -88.75 -11.99 -20.95 -37.07 -31.83 -8.45 -71.80 12 -0.28 -111.33 -17.53 -45.68 -39.48 -41.74 -5.84 -86.38 13 -0.35 -128.02 -21.20 -67.24 -39.17 -49.14 -4.59 -102.14 14 -0.51 -151.74 -23.85 -91.12 -37.88 -64.15 -4.29 -122.42 15 -0.41 -179.96 -26.91 -116.90 -37.36 -88.21 -3.95 -151.92 16 -0.27 166.93 -30.45 -133.25 -39.05 -106.29 -3.02 -168.71 17 -0.33 157.77 -33.85 -145.37 -42.49 -109.41 -2.77 179.33 18 -0.37 144.27 -37.31 -155.13 -44.53 -97.93 -2.54 169.25 19 -0.58 124.17 -41.44 -156.44 -42.48 -80.86 -3.33 156.65 20 -0.56 103.21 -49.19 -130.39 -40.96 -75.27 -3.99 129.84
12 part number ordering information part number no. of devices container MGA-30889-BLKG 100 antistatic bag mga-30889-tr1g 3000 13 tape/reel typical noise parameters (vdd = 5v, t a = 25c, 50 ohm) freq (ghz) f min (db) opt mag opt ang r n /z 0 0.4 1.80 0.036 -102 0.19 0.9 1.70 0.051 -86 0.19 1.0 1.75 0.071 -76 0.20 1.7 1.90 0.11 -52 0.25 1.95 1.93 0.17 -46 0.28 2.0 1.90 0.16 -41 0.29 2.5 1.81 0.24 -19 0.38 3.0 1.85 0.30 3.7 0.49 3.5 1.81 0.40 27 0.55 4.0 2.24 0.45 58 0.54 4.5 2.71 0.47 89 0.50 5.0 3.39 0.55 121 0.43
13 sot89 package dimensions dimensions in mm dimensions in inches symbols minimum nominal maximum minimum nominal maximum a 1.40 1.50 1.60 0.055 0.059 0.063 l 0.89 1.04 1.20 0.0350 0.041 0.047 b 0.36 0.42 0.48 0.014 0.016 0.018 b1 0.41 0.47 0.53 0.016 0.018 0.030 c 0.38 0.40 0.43 0.014 0.015 0.017 d 4.40 4.50 4.60 0.173 0.177 0.181 d1 1.40 1.60 1.75 0.055 0.062 0.069 d2 1.45 1.65 1.80 0.055 0.062 0.069 e 3.94 - 4.25 0.155 - 0.167 e1 2.40 2.50 2.60 0.094 0.098 0.102 e1 2.90 3.00 3.10 0.114 0.118 0.122 s 0.65 0.75 0.85 0.026 0.030 0.034 e 1.40 1.50 1.60 0.054 0.059 0.063 matte finish polish polish d d1 e1 e l b e e1 s c b1 b a or d2 d1 1.24 1.23 0.77 b1 0.2 half etching 1.625 2.35 depth 0.100 e d d1 e1 e l e e1 s or
14 device orientation tape dimensions dimensions in mm notes: 1. 10 sprocket hole pitch cumulative tolerance 0.2 2. camber in compliance with eia 481 3. pocket position relative to sprocket hole measured as true position of pocket, not pocket hole 12.0 .3 ao = 4.60 bo = 4.90 ko = 1.90 5.50 .05 see note 3 1.75 .10 8.00 ? 1.5 +0.1/-0.0 2.00 .05 see note 3 4.00 see note 1 section a - a ? 1.50 min. ao ko r 0.3 typ. r 0.3 max. 0.30 .05 a a bo user feed direction cover tape carrier tape reel 8gx 8gx 8gx 8gx
for product information and a complete list of distributors, please go to our web site: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies in the united states and other countries. data subject to change. copyright ? 2005-2013 avago technologies. all rights reserved. av02-2250en - may 23, 2013 reel dimensions C 13 reel ? 20.2 m i n 2.0 0.5 ? 13.0 +0.5 -0.2 102.0 ref 330.0 ref 8.4 (measured at hub) (measured at hub) "a" attention electrostatic sensitive devices safe handling required minneapolis usa u.s pat 4726534 r lokreel r 11.1 max. detail "a" detail "b" ps 6 6 p s 1.5 88 ref 96.5 +0.3 - 0.2 dimensions in mm

▲Up To Search▲

Price & Availability of MGA-30889-BLKG

	To Download MGA-30889-BLKG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .