1 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com features ? diplexer single mode single fiber 1x9 sc/sf/st receptacle connector ? wavelength tx 1310nm/rx 1530 nm ? sonet oc-3 sdh stm-1 compliant ? single +5v power supply [b-13/15-155-t-sxx5(7)] ? single +3.3v power supply [b-13/15-155-t3-sxx5(7) ] ? pecl/lvpecl differential inputs and outputs [b-13/15-155-t(3)-sxx5(7)] ? ttl/lvttl differential inputs and outputs [b-13/15-155c-t(3)-sxx5(7)] ? wave solderable and aqueous washable ? led multisourced 1x9 transceiver interchangeable ? class 1 laser int. safety standard iec 825 compliant ? uncooled laser diode with mqw structure ? complies with telcordia(bellcore) gr-468-core ? rohs compliance available parameter symbol min. max. unit note power supply voltage v cc 0 6 v b-13/15-155-t-sxx5(7) power supply voltage v cc 0 3.6 v b-13/15-155-t3-sxx5(7) output current i out - 30 ma soldering temperature - - 260 oc 10 seconds on leads only storage temperature t stg -40 85 oc absolute maximum rating parameter symbol min. typ. max. unit power supply voltage v cc 4.75 5 5.25 v power supply voltage v cc 3.1 3.3 3.5 v operating temperature (case) t opr 0 - 70 oc operating temperature (case) t opr 0 - 70 oc data rate - - 155 - mbps recommended operating condition parameter symbol min typical max unit notes optical optical transmit power p o -5 - 0 dbm output power is coupled into a 9/125 m single mode ?ber (b-13/15-155-t(3)-sxx5) optical transmit power p o -3 - +2 dbm output power is coupled into a 9/125 m single mode ?ber (b-13/15-155-t(3)-sxx7) output center wavelength 1260 1310 1360 nm output spectrumt width ? - - 3 nm rms ( ) extinction ratio er 10 - - db output eye compliant with itu-t recommendation g.957/stm-1 optical rise time t r - - 2 ns 10% to 90% values optical fall time t f - - 2 ns 10% to 90% values optical isolation - 30 - - db isolation potential between 1480-1580nm at least 30db relative intensity noise rin - - -116 db/hz total jitter tj - - 1.2 ns measured with 2 23 -1 prbs with 72 ones and 72 zeros. transmitter speci?cations
2 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com parameter symbol min typical max unit notes electrical power supply current i cc - - 200 ma maximum current is speci?ed at vcc= maximum @ maximum temperature data input current-low i il -350 - - a data input current-high i ih - - 350 a differential input voltage v ih -v il 300 - - mv data input voltage-low v il -v cc -2.0 - -1.58 v these inputs are compatible with 10k, 10kh and 100k ecl and pecl inputs data input voltage-high v ih -v cc -1.1 - -0.74 v transmitter speci?cations parameter symbol min typical max unit notes optical sensitivity - - - -33 dbm measured with 2 23 -1 prbs, ber = 10 -10 , b-13/15-155-t (3)- ssc 5 sensitivity - - - -35 dbm measured with 2 23 -1 prbs, ber = 10 -10 , b-13/15-155-t(3)-ssc 7 maximum input power p in -3 - - dbm signal detect-asserted (note 1) pa - - -33 dbm measured on transition : low to high b-13/15-155-t (3)- ssc5 signal detect-asserted (note 1) pa - - -35 dbm measured on transition : low to high b-13/15-155-t (3)-ssc 7 signal detect-deasserted (note 1) pd -45 - - dbm measured on transition: high to low b-13/15-155-t(3)-ssc5 signal detect-hysteresis 1.0 - 4.0 db wavelength of operation 1480 - 1600 nm note 1: regardless of whether the tx is on or not, sd should be asserted at less than -33 or -35 dbm of input power level and deasserted at higher than -45 dbm of input power level from the outside tx. receiver speci?cations parameter symbol min typical max unit note electrical power supply current i cc - - 100 ma the current excludes the output load current data output voltage-low v ol -v cc -2.0 - -1.58 v these outputs are compatible with 10k, 10kh and 100kecl and pecl outputs data output voltage-high v oh - v cc -1.1 - -0.74 v signal detect output voltage-low v sdl- v cc -2.0 - -1.58 v signal detect output voltage-high v sdh- v cc -1.1 - -0.74 v receiver speci?cations
3 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com warnings connection diagram 1. (rx gnd) 2. (rx +) nc 3. (rx-) 4. (sd) 5. (rx vcc) top view 6. (tx vcc) 7. (tx-) nc 8. (tx+) 9. (tx gnd) receiver signal ground receiver data out receiver data out bar signal detect receiver power supply transmitter power supply transmitter data in bar transmitter data in transmitter signal ground pin symbol notes 1 rxgnd directly connect this pin to the receiver ground plane 2 rd+ see recommended circuit schematic 3 rd- see recommended circuit schematic 4 sd active high on this indicates a received optical signal 5 rxvcc dc power for the receiver section 6 txvcc dc power for the transmitter section 7 td- see recommended circuit schematic 8 td+ see recommended circuit schematic 9 txgnd directly connect this pin to the transmitter ground plane
4 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com recommended circuit schematic (3.3v/5v) 1 2 3 4 5 9 7 8 6 rx vcc tx vcc transceiver top view no internal connection no internal connection c2 c1 c4 l2 c3 l1 rx vcc tx vcc vcc tx vcc rx vcc rd + rd - sd td + td - r8 r10 r9 r7 c6 c5 r1 r3 r2 r4 r5 r6 notes +3.3v: r1=r3=r5=r7=r9=130 ? r2=r4=r6=r8=r10=82 ? c1=c2=c3=c5=c6=0.1 ? f c4=10 ? f l1=l2=1 ? h notes +5v: r1=r3=r5=r7=r9=82 ? r2=r4=r6=r8=r10=130 ? c1=c2=c3=c5=c6=0.1 ? f c4=10 ? f l1=l2=1 ? h the split-loaded terminations for ecl signals need to be located at the input of devices r eceiving those ecl signals. the power supply ?ltering is required for good emi performance. use short tracks from the inductor l1/l2 to the module rx vcc. a gnd plane under the module is required for good emi and sensitivity performance. b-13/15-155-t(3)-sxx5(7) recommended circuit schematic (3.3v/5v) 1 2 3 4 5 9 7 8 6 rx vcc tx vcc transceiver top view no internal connection no internal connection c2 c1 c4 l2 c3 l1 rx vcc tx vcc vcc tx vcc rx vcc rd + rd - sd td + td - r6 r8 r7 c6 c5 r1 r3 r2 r4 r5 notes +3.3v: r1=r3=r5=r7=130 ? r2=r4=r6=r8=82 ? c1=c2=c3=c5=c6=0.1 ? f c4=10 ? f l1=l2=1 ? h notes +5v: r1=r3=r5=r7=82 ? r2=r4=r6=r8=130 ? c1=c2=c3=c5=c6=0.1 ? f c4=10 ? f l1=l2=1 ? h b-13/15-155c-t(3)-sxx5(7)
5 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com side view rear view top view front view package diagram b-13/15-155-t(3)-ssc5(7)
6 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com top view front view top view front view package diagram package diagram b-13/15-155-t(3)-sst5 ( 7) b-13/15-155-t(3)-sfc5( 7)
7 155 mbps bi-directional receptacle single fiber transceiver b-13/15-155(c)-t(3)-sxx5(7) 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 luminentoic.com ordering information b - 15/13 - 155 - t(3) - s xx tx p ower temperature and package - rohs ? wavelength tx wavelength=1530nm rx wavelength=1310nm ? communication protocol (155 mbps) ? connector options sc/st/fc ? t = +5v transceiver ? t3 = +3.3v transceiver ? single mode ?ber ? tx power 5 = -5 to 0 dbm 7 = -3 to +2 dbm part numbering de?nitions: available options: b-13/15-155(c)-t-ss c5(7)(a) b-13/15-155 (c) -t-s fc5(7) (a) b-13/1 5-155 (c) -t-sst5(7) (a) b-13/15-155 (c) -t3-ss c5(7) (a) b-13/15-155 (c) -t3-s fc5(7) (a) b-13/1 5-155 (c) -t3-sst5(7) (a) b-13/15-155 (c) -t-ss c5(7) (a) -g5 b-13/15-155 (c) -t-s fc5(7) (a) -g5 b-13/1 5-155 (c) -t-sst5(7) (a) -g5 b-13/15-155 (c) -t3-ss c5(7) (a) -g5 b-13/15-155 (c) -t3-s fc5(7) (a) -g5 b-13/1 5-155 (c) -t3-sst5(7) (a) -g5 b-13/15-155 (c) -t-ss c5(7) (a) -gr b-13/15-155 (c) -t-s fc5(7) (a) -gr b-13/1 5-155 (c) -t-sst5(7) (a) -gr b-13/15-155 (c) -t3-ss c5(7) (a) -gr b-13/15-155 (c) -t3-s fc5(7) (a) -gr b-13/1 5-155 (c) -t3-sst5(7) (a) -gr ? rohs blank = rohs non-compliant product g5 = rohs 5/6-compliant product (lead exemption) gr = full rohs compliant product (no exemption) ? temperature range and package blank = commercial temperature(0 to 70 oc) a = industrial temperature(-40 to 85 oc)
handling precautions: this device is susceptible to damage as a result of electrostatic discharge (esd). a static free environment is highly recommended. follow guidelines according to proper esd procedures. laser safety: radiation emitted by laser devices can be dangerous to human eyes. avoid eye exposure to direct or indirect radiation. 8 155 mbps bi-directional receptacle single fiber transceiver important notice! all information contained in this document is subject to change without notice, at luminentoic s sole and absolute discretion. luminentoic warrants performance of its products to current speci?cations only in accordance with the companys standard one-year warranty; however, speci?cations designated as preliminary are given to describe components only, and luminentoic expressly disclaims any and all warranties for said products, including express, implied, and statutory warran - ties, warranties of merchantability, ?tness for a particular purpose, and non-infringement of proprietary rights. please refer to the companys terms and conditions of sale for further warranty information. luminentoic assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. no license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and luminentoic makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. products described in this docu - ment are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. luminentoic customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify luminentoic for any damages resulting from such use or sale. the information contained in this document is provided on an as is basis. customer agrees that luminentoic is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. customer must contact luminentoic to obtain the latest version of this publication to verify , before placing any order, that the information contained herein is current. ? luminentoic, inc. 2003 all rights reserved luminentoic.com 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 lumnds617-dec2306 rev a.3 b-13/15-155(c)-t(3)-sxx5(7) warnings legal noice
|
