patent numbers 5713755 / 5961339 do not scale from this print "a" "a" rhle-50-d no of pos x .100 [2.54] .200 ref 5.08 .020 ref 0.51 .100 ref 2.54 2 max sway ({no of pos - 1} x .100 [2.54]) .005 [.13] c-132-12-xxx +.008 [.20] -.005 [.13] 01 c1 .144 3.66 .259 6.57 90 3 .146 3.70 section "a"-"a" c7 c8 .008 x .056 ref [.20 x 1.42] .0625 1.588 .050 1.27 .050 1.27 (no of pos x .1000) - .2000 [2.540] [5.080] sm-a10h lc-08-tm-01 c4 -a & -lc option figure 2 c5 "r" .152 3.86 "s" .225 5.72 mpp-02 figure 3 (-p: pick and place pad) available on positions 03 thru 50 note: "r" = use measured dim (ref) "s" = {("r" - .225 [5.72])/2} .020 [.51] c2 c10 .2559 6.500 .028 .010 [.71 .25] "s" (see note) "r" (see note) k-500-300 figure 4 -k: polymide film pad available on pos 03 thru 50 note: "r" = use measured dim (ref) "s" = {("r" - .2559 [6.500])/2} .020 [.51] .280 7.11 .149 3.78 c9 hle-1xx-02-xxx-dv-xx-xx-xx no of positions -02 thru -50 (per row) row specification -dv: double vertical (use rhle-50-d) lead style -02: surface mount (use c-132-12-x) plating specification -g: gold (use c-132-12-g) -s: selective gold (use c-132-12-s) -f: selective flash gold (use c-132-12-f) -l: selective light gold (use c-132-12-l) -h: heavy gold (use c-132-12-h) -stl: selective tin/lead (use c-132-12-stl) -sm selective gold/matte tin tail (use c-132-12-s) -fm selective flash gold/matte tin tail (use c-132-12-f) -lm light gold/matte tin tail (use c-132-12-l) option -tr: tape & reel (2 - 29 positions only) option -p: pick & place pad (pos -03 thru -50 only) -a: alignment pin (4 pos min) -lc: locking clip (2 pos min) -k: polyamide film pad (available on pos -03 thru -50; .005 [.13] thickness with silicone adhesive) (see fig. 1) option -be: bottom entry (use rhle-50-dbe)(see fig. 5) (leave blank for standard) figure 5 -be option (same as fig. 1 unless otherwise stated) rhle-50-dbe tube views pt-1-24-01-64 pt-1-24-10-63 see table 2 figure 1 hle-116-02-xxx-dv shown c6 c3 c 02 ac sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 3 .xxx: .005 [.13] .xxxx: .0020 [.051] material: [2.54] .100 tiger beam socket assembly by: hle-1xx-02-xxx-dv-xx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing ed messer 12/19/98 1 1 sheet scale: 1:1 body: vectra e130i contact: becu c:\enterprisevault\dwg\misc\mktg\hle-1xx-02-xxx-dv-xx-xx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. all identification marks must not stand greater than .002 [.05] off the surface of the part. 3. pull out force for -lc, -a, & contact is 12 oz min. 4. coplanarity: see table 2. 5. burr allowance: .003 [.08] max 6. cut assemblies after fill. cut flash to be .010 max with no flash allowed in holes or extending below leads. will lose a position for every cut made on a socket strip. 7. tube positions 03 thru 50. layer package position 02. 8. endwall thickness: .030+/-.005[.76+/-.13] to be measured from bottom view. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision ac
|
