View FTLX3611M317_6645997.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 1 product specification rohs-6 compliant 10gb/s dwdm 40km multi-rate xfp optical transceiver ftlx3611m3xx product features ? supports 9.95gb/s to 11.1gb/s bit rates ? hot-pluggable xfp footprint ? maximum link length of 40km ? temperature-stabilized dwdm- rated eml transmitter ? rohs-6 compliant (lead-free) ? 100ghz itu grid, c band ? duplex lc connector ? power dissipation <3.5w ? built-in digital diagnostic functions ? temperature range: -5c to 70c applications ? dwdm networks ? sonet oc-192 ir-2 sdh stm s-64.2b ? oc-192/stm-64 with fec ? 10gbase-er/ew ? 40km 10g fibre channel ? 10gbase-er/ew with fec finisar?s 40km ftlx3611m3xx small form f actor 10gb/s (xfp) transceivers comply with the current xfp multi-source agreement (msa) specification 1 . they comply with sonet oc-192 ir-2 and sdh stm s-64.2b, as well as with 10-gigabit ethernet 10gbase-er/ew per ieee 802.3ae and 10-gigabi t fibre channel. digital diagnostics functions are available via a 2- wire serial interface, as specified in the xfp msa. the transceiver is rohs co mpliant and lead free per directive 2002/95/ec 3 , and finisar application note an-2038 4 . product selection ftlx3611m3xx xx: 100ghz itu grid wavelength (see next page)
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 2 channel # product code frequency (thz) center wavelength (nm) 17* FTLX3611M317 191.7 1563.86 18 ftlx3611m318 191.8 1563.05 19 ftlx3611m319 191.9 1562.23 20 ftlx3611m320 192.0 1561.42 21 ftlx3611m321 192.1 1560.61 22 ftlx3611m322 192.2 1559.79 23 ftlx3611m323 192.3 1558.98 24 ftlx3611m324 192.4 1558.17 25 ftlx3611m325 192.5 1557.36 26 ftlx3611m326 192.6 1556.55 27 ftlx3611m327 192.7 1555.75 28 ftlx3611m328 192.8 1554.94 29 ftlx3611m329 192.9 1554.13 30 ftlx3611m330 193.0 1553.33 31 ftlx3611m331 193.1 1552.52 32 ftlx3611m332 193.2 1551.72 33 ftlx3611m333 193.3 1550.92 34 ftlx3611m334 193.4 1550.12 35 ftlx3611m335 193.5 1549.32 36 ftlx3611m336 193.6 1548.51 37 ftlx3611m337 193.7 1547.72 38 ftlx3611m338 193.8 1546.92 39 ftlx3611m339 193.9 1546.12 40 ftlx3611m340 194.0 1545.32 41 ftlx3611m341 194.1 1544.53 42 ftlx3611m342 194.2 1543.73 43 ftlx3611m343 194.3 1542.94 44 ftlx3611m344 194.4 1542.14 45 ftlx3611m345 194.5 1541.35 46 ftlx3611m346 194.6 1540.56 47 ftlx3611m347 194.7 1539.77 48 ftlx3611m348 194.8 1538.98 49 ftlx3611m349 194.9 1538.19 50 ftlx3611m350 195.0 1537.40 51 ftlx3611m351 195.1 1536.61 52 ftlx3611m352 195.2 1535.82 53 ftlx3611m353 195.3 1535.04 54 ftlx3611m354 195.4 1534.25 55 ftlx3611m355 195.5 1533.47 56 ftlx3611m356 195.6 1532.68 57 ftlx3611m357 195.7 1531.90 58 ftlx3611m358 195.8 1531.12 59 ftlx3611m359 195.9 1530.33 60 ftlx3611m360 196.0 1529.55 61* ftlx3611m361 196.1 1528.77 * this channel is supported with limited availab ility -- please contact finisar for further details.
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 3 i. pin descriptions pin logic symbol name/description ref. 1 gnd module ground 1 2 vee5 optional ?5.2 power supply ? not required 3 lvttl-i mod-desel module de-select; when held low allows the module to respond to 2-wire serial interface commands 4 lvttl-o interrupt interrupt (bar); indicates pres ence of an important condition which can be read over the serial 2-wire interface 2 5 lvttl-i tx_dis transmitte r disable; transmitter laser source turned off 6 vcc5 +5 power supply 7 gnd module ground 1 8 vcc3 +3.3v power supply 9 vcc3 +3.3v power supply 10 lvttl-i scl serial 2-wire interface clock 2 11 lvttl- i/o sda serial 2-wire interface data line 2 12 lvttl-o mod_abs module absent; indicates module is not present. grounded in the module. 2 13 lvttl-o mod_nr module not ready; finisar defines it as a logical or between rx_los and loss of lock in tx/rx. 2 14 lvttl-o rx_los receiver lo ss of signal indicator 2 15 gnd module ground 1 16 gnd module ground 1 17 cml-o rd- receiver inverted data output 18 cml-o rd+ receiver non- inverted data output 19 gnd module ground 1 20 vcc2 +1.8v power supply 21 lvttl-i p_down/rst power down; when high, places the module in the low power stand-by mode and on the falling edge of p_down initiates a module reset reset; the falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 vcc2 +1.8v power supply 23 gnd module ground 1 24 pecl-i refclk+ reference clock non-inverted input, ac coupled on the host board ? not required 25 pecl-i refclk- reference clock inverted input, ac coupled on the host board ? not required 26 gnd module ground 1 27 gnd module ground 1 28 cml-i td- transmitter inverted data input 29 cml-i td+ transmitter non-inverted data input 30 gnd module ground 1 notes : 1. module circuit ground is isolated from module chassis ground within the module. 2. open collector; should be pulled up with 4.7k ? 10kohms on host board to a voltage between 3.15v and 3.6v.
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 4 diagram of host board connect or block pin numbers and names ii. absolute maximum ratings parameter symbol min typ max unit ref. maximum supply voltage 1 vcc3 -0.5 4.0 v maximum supply voltage 2 vcc5 -0.5 6.0 v storage temperature t s -40 85 c case operating temperature t op -5 70 c
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 5 iii. electrical characteristics (t op = -5 to 70 c, v cc5 = 4.75 to 5.25 volts) parameter symbol min typ max unit ref. main supply voltage vcc5 4.75 5.25 v supply voltage #2 vcc3 3.13 3.45 v supply voltage #3 vcc2 1.71 1.89 v supply current ? vcc5 supply icc5 350 ma supply current ? vcc3 supply icc3 400 ma supply current ? vcc2 supply icc2 750 ma module total power p 3.5 w 1 transmitter input differential impedance r in 100 2 differential data input swing vin,pp 120 820 mv transmit disable voltage v d 2.0 vcc v 3 transmit enable voltage v en gnd gnd+ 0.8 v transmit disable assert time 10 us receiver differential data output swing vout,pp 340 650 850 mv 4 data output rise time t r 38 ps 5 data output fall time t f 38 ps 5 los fault v los faul t vcc ? 0.5 vcc host v 6 los normal v los nor m gnd gnd+0.5 v 6 power supply rejection psr see note 6 below 7 reference clock clock differential input impedance rclk in 100 reference clock frequency f0 baud/64 mhz differential clock input swing vclkin,pp 640 1600 mv clock output rise/fall time t rf 200 1250 ps 5 reference clock frequency tolerance df -100 +100 ppm notes : 1. maximum total power value is specified acro ss the full temperature and voltage range. 2. after internal ac coupling. 3. or open circuit. 4. into 100 ohms differential termination. 5. 20 ? 80 % 6. loss of signal is open collector to be pulled up with a 4.7k ? 10kohm resistor to 3.15 ? 3.6v. logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. per section 2.7.1. in the xfp msa specification 1 .
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 6 iv. optical characteristics (t op = -5 to 70 c, v cc5 = 4.75 to 5.25 volts) please note that the transmitter of the ftlx3611m3 becomes operational within 60 seconds of power-up. this is due to the tim e required for the eml to reach its optimum operating temperature. parameter symbol min typ max unit ref. transmitter output opt. pwr: 9/125 smf p out -1 +2 dbm 1 optical extinction ratio er 8.2 db 1 center wavelength spacing 100 ghz 2 transmitter center wavelength ? end of life x-100 x x+100 pm 3 transmitter center wavelength ? beginning of life x-25 x x+25 pm 3 transmitter dispersion penalty (@ 800 ps/nm) tdp 2 db sidemode supression ratio ssr min 30 db tx jitter generation (peak-to-peak) tx j 0.1 ui 4 tx jitter generation (rms) tx jrms 0.01 ui 5 relative intensity noise rin -130 db/hz receiver receiver sensitivity @ 9.95gb/s to 11.1gb/s r sens1 -16 dbm 6 stressed receiver sensitivity (oma) @ 11.1gb/s r sens2 -11.3 dbm 7 maximum input power p max -1 dbm optical center wavelength having er=8.2db guarantees that the ?1 dbm minimum output power meets ieee 802.3ae requirement of oma = -2.4 dbm. 2. corresponds to approximately 0.8 nm. 3. x = specified itu grid wavelength. 4. measured with a host jitter of 50 mui peak-to-peak. 5. measured with a host jitter of 7 mui rms. 6. measured with worst er; ber<10 -12 ; prbs31. equivalent to ?14.3 dbm oma at er = 8.2 db. 7. per ieee 802.3ae. equivalent to ?14.3 dbm average power at infinite er. 8. dispersion penalty is measured in loopback using 18 ps/(nm*km) fiber (smf-28).
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 7 v. general specifications parameter symbol min typ max units ref. bit rate br 9.95 11.1 gb/s 1 bit error ratio ber 10 -12 2 max. supported link length l max 40 km 1 notes : 1. sonet oc-192 ir-2, 10gbase-er/ew, sonet oc-192 with fec, 10gbase-er/ew with fec 2. tested with a 2 31 ? 1 prbs vi. environmental specifications finisar xfp transceivers have an operating temperature range from -5c to +70c case temperature. parameter symbol mi n typ max units ref. case operating temperature t op -5 70 c storage temperature t sto -40 85 c vii. regulatory compliance finisar xfp transceivers are class 1 laser products. they are certified per the following standards: feature agency standard certificate number laser eye safety fda/cdrh cdrh 21 cfr 1040 and laser notice 50 9210176-77 laser eye safety tv en 60825-1: 2007, en60825-2:2004+a1 iec 60825-1: 2007 (2 nd edition) iec 60825-2: 2010 (3 rd edition) 72101686 electrical safety tv en 60950:2006+a11 72101686 electrical safety ul/csa class 3862.07 class 3862.87 2283290 copies of the referenced cer tificates are available at fi nisar corporation upon request.
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 8 viii. digital diagnostics functions as defined by the xfp msa 1 , finisar xfp transceivers provide digita l diagnostic functions via a 2-wire serial interface, wh ich allows real-time access to the following operating parameters: ? transceiver temperature ? laser bias current ? transmitted optical power ? received optical power ? transceiver supply voltage it also provides a sophisticated system of al arm and warning flags, which may be used to alert end-users when particul ar operating parameters are out side of a factory-set normal range. the operating and diagnostics informati on is monitored and reported by a digital diagnostics transceiver controller (ddtc) inside the transceiver, which is accessed through the 2-wire serial interf ace. when the serial protocol is activated, the serial clock signal (scl pin) is generated by the host. the positive edge clocks data into the xfp transceiver into those segments of its memo ry map that are not write-protected. the negative edge clocks data from the xfp transc eiver. the serial da ta signal (sda pin) is bi-directional for serial data transfer. th e host uses sda in conjunction with scl to mark the start and end of serial protocol activation. the memories are organized as a series of 8-bit data words th at can be addressed individually or sequentially. the 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. for more detailed information, including memory map definitions, please see the xfp msa documentation 1 .
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 9 ix. mechanical specifications finisar?s xfp transceivers are compliant wi th the dimensions defined by the xfp multi- sourcing agreement (msa). 77.95 18.35 22.15 8.50 13.30 1.95 39.00 16.00 r1.00 20.85 latched unlatched xfp transceiver (dimensions are in mm)
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 10 x. pcb layout and bezel recommendations xfp host board mechanical layout (dimensions are in mm)
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 11 xfp detail host board mechanical layout (dimensions are in mm)
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 12 xfp recommended bezel design (dimensions are in mm)
ftlx3611m3 dwdm xfp product specification ? january 2011 f i n i s a r ? finisar corporation 11-january-2011 rev c1 page 13 xi. references 1. 10 gigabit small form factor pluggabl e module (xfp) multi-source agreement (msa), rev 4.5 ? august 2005. document ation is currently available at http://www.xfpmsa.org/ 2. application note an-2035: ?digital di agnostic monitoring interface for xfp optical transceivers? ? finisa r corporation, december 2003 3. directive 2002/95/ec of the european council parliament and of the council, ?on the restriction of the use of certain hazardous substances in electrical and electronic equipment?. january 27, 2003. 4. ?application note an-2038: finisar im plementation of rohs compliant transceivers?, finisar corporation, january 21, 2005. xii. revision history revision date description a 4/12/2006 ? document created. a1 4/21/2006 ? added oc-192/stm-64 with fec in applications section ? removed finisar confidential from footer. ? replaced product photo. a2 5/22/2006 ? updated bol wavelength tolerance specification. ? updated finisar address. b 10/25/2006 ? added safety certificate numbers. ? document release. b1 9/28/2007 ? updated note on channel. b2 2/7/2008 ? added channel column. c1 1/11/2011 ? update channel availability xii. for more information finisar corporation 1389 moffett park drive sunnyvale, ca 94089-1133 tel. 1-408-548-1000 fax 1-408-541-6138 sales@finisar.com www.finisar.com

▲Up To Search▲

Price & Availability of FTLX3611M317

	To Download FTLX3611M317 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .