skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 200050e ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? nov ember 12, 2010 1 data sheet smp1330 series: plastic packaged limiter diodes applications ? wlan, wimax ? cellular infrastructure ? rfid readers ? test instruments features ? low-distortion design ? limiter performance to 2 ghz and higher ? low insertion loss ? low-cost plastic package ? sot-23 pb-free (msl1, 260 ? c per jedec j-std-020) package description the smp1330 series of limiter diodes is designed for use as passive receiver protectors in wireless and other rf systems covering frequencies up to 2 ghz and higher. these diodes use skyworks limiter diode technology to produce gold-doped, thin base limiters for low-loss, low-distortion performance and good limiter action. the smp1330 series of diodes has been characterized in limiter circuits and tightly specified to ensure consistent performance. the absolute maximum ratings of the smp1330 series are provided in table 1. table 1. smp1330 series absolute maximum ratings parameter symbol minimum maximum units reverse voltage v r 20 v forward current i f 100 ma cw incident power @ 25 c lead temperature 1 w peak incident power @ 1% duty factor, 1 s pulse 100 w power dissipation @ 25 c lead temperature p d 250 mw storage temperature t stg C65 +150 ? c operating temperature t a C65 +150 ? c note: exposure to maximum rating conditions for extended periods may reduce device reliability. there is no damage to device with on ly one parameter set at the limit and all other parameters set at or below their nominal value. caution : although this device is designed to be as robust as possible, electrostatic discharge (esd) can damage this device. this devi ce must be protected at all times from esd. static charges may eas ily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. industry-standard esd precautions should be used at all times. the smp1330 series of limiter diodes are class 2 esd devices.
data sheet ? smp1330 series diodes skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 2 november 12, 2010 ? skyworks proprietary information ? pro ducts and product information are subject to change without not ice ? 200050e configurations as illustrated in figure 1, the smp1330 series is available in two wiring configurations, each using an industry standard sot-23 package. figure 1. smp1330 series sot-23 configurations electrical and mechanical specifications the part numbers and configurations for the smp1330 series are provided in table 2. electrical specifications are provided in table 3. typical 1 ghz limiter performance measurements are provided in table 4. input power vs output power performance for the smp1330 series is illustrated in figure 2. package dimensions for the sot-23 are shown in figure 3, and tape and reel dimensions are provided in figure 4. package and handling information instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. the smp1330 series is rated to moisture sensitivity level 1 (msl1) at 260 ? c. these diodes can be used for lead or lead-free soldering. for additional information, refer to the skyworks application note, solder reflow information , document number 200164 care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. production quantities of this product are shipped in a standard tape and reel format. table 2. part number and configuration series pair low inductance sot-23 sot-23 SMP1330-005 marking: pq2 smp1330-007 marking: pqb SMP1330-005lf green? marking: rq2 smp1330-007lf green? marking: rqb l s = 1.5 nh l s = 0.4 nh the pb-free symbol or lf in the part numbe r denotes a lead-free, rohs-compliant package unless otherwise noted as green?. tin/lead (sn/pb) packaging is not recommended for new designs.
data sheet ? smp1330 series diodes skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 200050e ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? nov ember 12, 2010 3 table 3. smp1330 series electrical specifications (t a = +25 ? c unless otherwise noted) parameter symbol test condi tion min typical max units series resistance r s f = 100 mhz, i f = 10 ma 1.2 1.5 capacitance c t 0 v f = 1 mhz f = 1 ghz 0.7 0.7 1.0 pf pf conductance g 0 v, f = 1 ghz 50 s carrier lifetime ti i f = 10 ma 4 ns i region width 3 m breakdown voltage v b i r = 10 a 20 35 50 v note 1: performance is guaranteed only under the conditions listed in this table. table 4. typical 1 ghz limiter performance parameter SMP1330-005 condition connection parallel insertion loss 0.3 db input power = C20 dbm ip3 +30 dbm input power = < 0 dbm 1 db compression +10 dbm attenuation @ +20 dbm 8.8 db attenuation @ +30 dbm 14 db input power (dbm) output power (dbm) +25 +20 +15 +10 +5 0 0 +10 +14 +18 +22 +26 +30 005 007 figure 2. typical 1 ghz limiter performance
data sheet ? smp1330 series diodes skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 4 november 12, 2010 ? skyworks proprietary information ? pro ducts and product information are subject to change without not ice ? 200050e 3 2 1 0.035 (0.89 mm) min. 0.044 (1.12 mm) max. 0.0005 (0.01 mm) min. 0.004 (0.10 mm) max. 0.012 (0.30 mm) min. 0.020 (0.50 mm) max. 0.003 (0.080 mm) min. 0.008 (0.20 mm) max. 8 max. 0.022 (0.55 mm) ref. 0.110 (2.80 mm) min. 0.120 (3.04 mm) max. 0.083 (2.10 mm) min. 0.104 (2.64 mm) max. 0.037 (0.95 mm) ref. 0.047 (1.20 mm) min. 0.055 (1.40 mm) max. 0.076 (1.92 mm) ref. 0.020 (0.51 mm) ref. s1389 figure 3. sot-23 package dimension drawing s225 9 notes: 1. carrier tape: black conductive polycarbonate. 2. cover tape: transparent conductive material. 3. cover tape size: 5.5 mm width. 4. esd surface resistivity is 1 x 10 5 ~ 1 x 10 11 ohms/square. 5. all measurements are in millimeters. 6. standard reel size is 7 inches. standard reel quantity is 3000 pcs. 8.00 0.10 3.50 0.05 a a a bb b ? 1.50 + 0.1/C0 pin 1 0.22 0.04 4.00 0.10 0. 99 2.00 0.05 2.00 0.05 3.15 0.05 ao 0.22 0.04 2.77 0.05 bo 1.22 0.05 ko 1.75 0.10 figure 4. sot-23 tape and reel dimensions
data sheet ? smp1330 series diodes skyworks solutions, inc. ? phone [ 781] 376-3000 ? fax [781] 376-3100 ? sales@ skyworksinc.com ? www.skyworksinc.com 200050e ? skyworks proprietary information ? products and product in formation are subject to cha nge without notice ? nov ember 12, 2010 5 copyright ? 2009, 2010 skyworks solutions, inc. all rights reserved. information in this document is provided in connection with skyw orks solutions, inc. (skyworks) products or services. these m aterials, including the information co ntained herein, are provided by skyworks as a service to its customers and may be used for info rmational purposes only by the cu stomer. skyworks assumes no res ponsibility for errors or omissions in these materials or the information contained herein. skyworks may change its documentat ion, products, services, specific ations or product descriptions at any time, without notice. skyworks makes no commitment to update the materials or information and shall have no responsi bility whatsoever for conflicts, incompatibilities, or other diff iculties arising from any future changes. no license, whether express, implied, by es toppel or otherwise, is granted to any in tellectual property rights by this document . skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, re production or use of skyworks products, information or mate rials, except as may be provided in skyworks terms and conditions of sale. the materials, products and information are pr ovided as is without warranty of any ki nd, whether express, implied, statutory, or otherwise, including fitness for a particular purpose or use, merchantability, performance, qualit y or non-infringement of any intellectual property right; all su ch warranties are hereby expressly disclaimed. skyworks does not warrant the accura cy or completeness of the information, text, graphics or other items contained within these ma terials. skyworks shall not be liable for any damages, including but not limited to any special, indirect, incidental, statutory, or consequentia l damages, including without limitation, lost revenues or lost profits that may result from the use of the materials or information, wheth er or not the recipient of mat erials has been advised of the possibility of such damage. skyworks products are no t intended for use in medical, lifesaving or life-su staining applications, or other equipment in which the failure of the skyworks products could lead to personal injury, death, physical or environmental damage. skyw orks customers using or selli ng skyworks products for use in such applications do so at their own risk and agree to fully indemnify skyworks for any damages resulting from such improper use or sale. customers are responsible for their products and applications us ing skyworks products , which may deviate from published specifi cations as a result of design de fects, errors, or operation of products outside of published pa rameters or design specifications. customers sh ould include design and operating safeguards to minimize these and other risks. skyworks assumes no liability for applications assistance, customer product de sign, or damage to any equipment resulting from the use of skyw orks products outsid e of stated published specifications or parameters. skyworks, the skyworks symbol, a nd breakthrough simplicity are trademarks or registered tradem arks of skyworks solutions, inc ., in the united states and othe r countries. third-party brands and names are for identification purposes only, and are the proper ty of their respective owners. additional information, includ ing relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.
|
