Part Number Hot Search : 
64400 LPC2129 CM7257 5357B SSP7442N EGFZ15D A1020 91C100
Product Description
Full Text Search
 

To Download TA8251AH Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  TA8251AH 2002-10-30 1 toshiba bipolar linear integrated circuit silicon monolithic TA8251AH max power 30w btl 4ch audio power ic the TA8251AH is 4ch btl audio power amplifier for consumer application. it is designed low distortion ratio for 4ch btl audio power amplifier, built ? in stand ? by function, muting function and junction temperature detection circuit. additionally, the aux. amplifier is built ? in, it can make the beep signal etc. output to 2 channels (out1 and 4). it contains various kind of protectors for car audio. features  high power : p out (max) = 30w (typ.) (v cc = 13.7v, f = 1khz, r l = 4 ? ) : p out (1) = 21w (typ.) (v cc = 14.4v, f = 1khz, thd = 10%, r l = 4 ? ) : p out (2) = 18w (typ.) (v cc = 13.2v, f = 1khz, thd = 10%, r l = 4 ? )  low distortion ratio : thd = 0.02% (typ.) (v cc = 13.2v, f = 1khz, p out = 3w, r l = 4 ? )  low noise : v no = 0.10mv rms (typ.) (v cc = 13.2v, r g = 0 ? , g v = 34db, bw = 20~20khz)  built ? in stand ? by switch function (pin(2))  built ? in muting function (pin(1), (25))  built ? in aux. amplifier from single input to 2 channels output (pin(16))  built ? in junction temperature detection circuit (pin(24)) : pin(24) dc voltage rises at about +10mv / c in proportion to junction temperature.  built ? in various protection circuit : thermal shut down, over voltage, out to gnd, out to v cc , out to out short  operating supply voltage : v cc (opr) = 9~18v weight: 9.8g (typ.)
TA8251AH 2002-10-30 2 block diagram
TA8251AH 2002-10-30 3 caution and application method (description is made only on the single channel.) 1. voltage gain adjustment this ic has no nf (negative feedback) terminals. therefore, the voltage gain can?t adjusted, but it makes the device a space and total costs saver. the voltage gain of amp. 1: g v1 = 0db the voltage gain of amp. 2a, b: g v2 = 28db the voltage gain of btl connection: g v (btl) = 6db therefore, the total voltage gain is decided by expression below. g v = g v1 + g v2 + g v (btl) = 0 + 28 + 6 = 34db 2. stand  by sw function by means of controlling pin(2) (stand  by terminal) to high and low, the power supply can be set to on and off. the threshold voltage of pin(2) is set at about 3v (typ.), and the power supply current is about 100a (typ.) at the stand  by state. control voltage of pin(2): v (sb) stand  by power v (sb) (v) on off 0~2 off on 3~v cc adjustage of stand  by sw (1) since v cc can directly be controlled to on or off by the microcomputer, the switching relay can be omitted. (2) since the control current is microscopic the switching relay of small current capacity is satisfactory for switching
TA8251AH 2002-10-30 4 3. preventive measure against oscillation for preventing the oscillation, it is advisable to use c 4 , the condenser of polyester film having small characteristic fluctuation of the temperature and the frequency. the resistance r to be series applied to c 4 is effective for phase correction of high frequency, and improves the oscillation allowance. (1) capacity value and the kind of condenser (2) layout of printed board 4. junction temperature detecting pin(24) using temperature characteristic of a band gap circuit and in proportion to junction temperature, pin(24) dc voltage: v 2 rises at about +10mv / c temperature characteristic. so, the relation between v 2 at t j = 25c and v 2x at t j = xc is decided by the following expression: c) ( 25 c 10mv / c) (25 2 v 2x v c) (x t        in deciding a heat sink size, a junction temperature can be easily made clear by measuring voltage at this pin while a backside temperature of ic was so far measured using a thermocouple type thermometer.
TA8251AH 2002-10-30 5 5. muting function: pin(1), pin(25) by means of controlling pin(25) (mute control terminal) less than about 1.5v, it can make the ic muting condition as below. however, pin(25) must not be connected to a certain voltage, for example, v cc , v dd , v ref , etc. in other words, pin(25) is inhibited to be pulled up, for instance fig. 5 application. the attenuation by the muting function is 70db (typ.). this muting is very smooth attenuating by the time constant of pin(1): smoothing. therefore, this function is suitable to the audio muting. the time for attenuation: tatt is adjustable by changing the capacitance of c 3 . but the tatt may influence the popping noise level. so, please decide the time of tatt by testing on the units. 6. aux. amplifier: pin(16) the pin(16) is for input terminal of aux. amplifier. the total gain is 0db by using of aux. amplifier. therefore, the  con can directly drive the aux. amplifier.
TA8251AH 2002-10-30 6 the amplified signal from pin(16) is out to the out1 and 4. 7. cross talk the cross talk characteristics of the ic is not good between out1 and 2, out3 and 4. so we recommend to use by below method. out1, 2 l  ch (or r  ch) out3, 4 r  ch (or l  ch) and, please refer to below table in case of applying the aux. in because it is out to out1 and 4. ex) out1 front aux. out out2 rear l  ch (or r  ch) ? out3 rear ? out4 front r  ch (or l  ch) aux. out
TA8251AH 2002-10-30 7 maximum ratings (ta = 25c) characteristic symbol rating unit peak supply voltage (0.2s) v cc (surge) 50 v dc supply voltage v cc (dc) 25 v operating supply voltage v cc (opr) 18 v output current (peak) i o (peak) 9 a power dissipation p d (*) 83 w operating temperature t opr  40~85 c storage temperature t stg  55~150 c (*) package thermal resistance j  t = 15c / w (typ.) (ta = 25c, with infinite heat sink) electrical characteristics (unless otherwise specified v cc = 13.2v, f = 1khz, r l = 4 ? , ta = 25c) characteristic symbol test cir  cuit test condition min. typ. max. unit quiescent current i ccq ?v in = 0 ? 200 400 ma p out (max) ? v cc = 13.7v, max power ? 30 ? p out (1) ? v cc = 14.4v, thd = 10% ? 21 ? output power p out (2) ? thd = 10% 16 18 ? w total harmonic distortion thd ? p out = 3w ? 0.02 0.2 % voltage gain g v ?v out = 0.775v rms (0dbm) 32 34 36 db voltage gain ratio ? g v ?v out = 0.775v rms (0dbm)  1.0 0 1.0 db v no (1) ?r g = 0 ? , din45405 ? 0.12 ? mv rms output noise voltage v no (2) ?r g = 0 ? , bw = 20hz~20khz ? 0.10 0.35 mv rms ripple rejection ratio r.r. ? f rip = 100hz, r g = 620 ? v rip = 0.775v rms (0dbm) 40 55 ? db cross talk c.t. ? r g = 620 ? , v out = 0.775v rms (0dbm) ? 75 ? db output offset voltage v offset ??  300 0 +300 mv input resistance r in ? ? ? 30 ? k ? stand  by current i sb ? stand  by condition ? 100 150 a v sb h ? power: on 3.0 ? v cc stand  by control voltage v sb l ? power: off 0 ? 1.5 v v m h ? mute: off open mute control voltage (*) v m l ? mute: on 0 ? 1.5 v mute attenuation att m ? mute: on ? 70 ? db (*) muting function must be controlled by open and low logic. this means that the mute control terminal: pin(25) must not be pulled up.
TA8251AH 2002-10-30 8 test circuit (g v = 34db)
TA8251AH 2002-10-30 9
TA8251AH 2002-10-30 10 . . . . . . . .
TA8251AH 2002-10-30 11 r.r.
TA8251AH 2002-10-30 12 package dimensions weight: 9.8g (typ.)
TA8251AH 2002-10-30 13  toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc..  the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk.  the products described in this document are subject to the foreign exchange and foreign trade laws.  the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others.  the information contained herein is subject to change without notice. 000707eb a restrictions on product use


▲Up To Search▲   

 
Price & Availability of TA8251AH

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X