originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 1 of 6 p1rx4c-sx4-01mm product specification sheet
originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 2 of 6 1.0 features ? multiple signals from one multimode fiber ? integrated tia and limiting amp ? metal enclosure with sc optical interface ? cml outputs this device is extremely sensitive to electrostatic discharge (esd). at a minimum, a ll handling must be performed in accordance with an ansi-compliant esd control program (ansi/esd s20.20-2007) to mitigate possible esd-induced damage. reliability and life of the device will be adversely affected if these p recautions are not met. this device is a class 3r laser device (per iec 608 25-1:2007) and can cause damage to eye sight if use d improperly. refer to ansi z136 for proper handling and usage of class 3r devi ces.
originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 3 of 6 2.0 absolute maximum ratings parameter symbol min typ max units storage temperature 1, 3 tst c 3.3v supply voltage vcc1 v operating surface temperature 2 ta c operating humidity 3 rh % durability C sc connector 200 cycles durability C plug-down connector 50 cycles 3.0 optical characteristics parameter (per channel) symbol min typ max units wavelength C lane 0 778 nm wavelength C lane 1 800 nm wavelength C lane 2 825 nm wavelength C lane 3 850 nm data rate per channel 4 p1rx4c-sx4v-01 p1rx4c-sx4d-01 d r gb/s peak optical input power pin dbm oma sensitivity 5 -16.00 dbm 4.0 electrical specifications 1 stresses listed may be applied without causing dama ge. functionality at or above the values listed is not implied. exposure to these values for extended periods may affect reliability. 2 see outline drawing for measurement point. 3 non condensing, 80% rh. 4 requires dc-balanced data pattern and max run rate of 80 bits. measured with input signals conformin g to hdmi rev 1.3a, section 4.2.5, figure 4-20. 5 optical modulation amplitude. based on an unstres sed input signal. 6 based on a jitter-free source 7 cml interface through a 100-ohm differential load. 8 this output is asserted low when a loss of signal i s detected on all lanes parameter symbol min typ max units low frequency cutoff f cutoff 175 khz total jitter (rms), per lane 6 t j1 10 ps differential output voltage 7 v od 500 mvp-p loss of signal assert sensitivity los sen-on -14.50 dbm loss of signal de-assert sensitivity los sen-off -13.00 dbm loss of signal output low 8 v los v loss of signal output high v los v operating supply voltage v cc 3.30 v operating supply current i cc 127 ma
originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 4 of 6 5.0 pin numbers and descriptions the rx-sx4 plugs into a 30 pin connector. for info rmation on the specifications of the connector, contact hirose (df12(4.0)-30dp-0.5v(86)). pin # signal description 1 gnd ground 2 los global loss of signal indicator 3 +td0 positive data output (778nm) 4 nc no connect 9 5 -td0 negative data output (778nm) 6 nc no connect 9 7 +td1 positive data output (800nm) 8 nc no connect 9 9 -td1 negative data output (800nm) 10 nc no connect 9 11 +td2 positive data output (825nm) 12 nc no connect 9 13 -td2 negative data output (825nm) 14 nc no connect 9 15 +td3 positive data output (850nm) 16 nc no connect 9 17 -td3 negative data output (850nm) 18 nc no connect 9 19 gnd ground 20 nc no connect 9 21 nc no connect 9 22 nc no connect 9 23 nc no connect 9 24 nc no connect 9 25 nc no connect 9 26 nc no connect 9 27 nc no connect 9 28 vcc 3.3 volt input. 29 gnd ground 30 vcc 3.3 volt input. 6.0 laser safety the p1rx4-sx4x-01 meets class-3 requirements. 9 nc = no connect. do not connect anything to this pin.
originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 5 of 6 7.0 environmental standards omron network products designs and manufactures its products to minimize the negative impact on our environment. as such, the p1rx4c-sx4-01mm conforms to a variety of environmental and safety s tandards standard compliant certificate available rohs yes yes
originator: c. eng date: 7/8/2011 document no. doc002326 rev a p1rx4c-sx4x-01mm product specification sheet 6 of 6 dimensions the sx4 rosa is designed to work with a standard sc ferrule only. insertion of any other type may result in damage. dimensions (mm) and orientation are for reference o nly. temperature measurement point
|
