bel fuse inc. 206 van vorst street, jersey city, nj 07302 ? tel 201-432-0463 fax 201-432-9542 www.belfuse.com ?2002 bel fuse inc. specifications subject to change without notice. 10.02 tm02307 g.shdsl magnetics electrical specifications at 25 c schematic operating and storage temperature range: -40 to +85 c meets iec 695, 2-2 flammability requirements pwb process capability: standard printed wiring board assembly techniques, total-immersion cleaning reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias S560-6600-HG page 1 all measurements are made with pins 2 and 3 connected and pins 5 and 7 connected 1. inductance measured at 10 khz, 0.1 vac 2. measured at 100 khz, 0.1 vac 3. measured with line impedance of 135 ? and chip impedance of 275.5 ? designed to comply with the requirements of ul1950 and en60950 to provide an insulation barrier with a working voltage of 150v minimum interwinding breakdown voltage of 1500 vrms minimum interwinding voltage of 600 vrms between pins 1 and 2 for one minute for power cross requirement ic 8 6 7 3 1 2 line 4 5 r e b m u n t r a p o i t a r s n r u t % 2 e c n a t c u d n i 1 % 7 h m e g a k a e l e c n a t c u d n i 2 x a m h r c d ? ? ? ? ? x a m l a n i d u t i g n o l e c n a l a b 3 x a m b d n o i t r e s n i s s o l x a m b d c i n o m r a h n o i t r o t s i d 3 x a m b d e n i l : p i h c e d i s e n i l e d i s e n i l e d i s p i h c e d i s e n i l - z h k 0 2 z h k 0 0 5 z h k 0 0 1 s m r v 2 z h k 5 g h - 0 0 6 6 - 0 6 5 s0 7 . 0 : 18 1 . 35 14 29 . 75 4 -5 . 12 8 -
corporate bel fuse inc. 206 van vorst street jersey city, nj 07302 tel 201-432-0463 fax 201-432-9542 www.belfuse.com far east bel fuse ltd. 8f / 8 luk hop street san po kong kowloon, hong kong tel 852-2328-5515 fax 852-2352-3706 www.belfuse.com europe bel fuse europe ltd. preston technology management centre marsh lane, suite g7, preston lancashire, pr1 8ud, u.k. tel 44-1772-556601 fax 44-1772-888366 www.belfuse.com ?2002 bel fuse inc. specifications subject to change without notice. 10.02 tm02307 g.shdsl magnetics mechanical page 2 S560-6600-HG tape and reel packaging 24 mm wide by 20 mm pitch; 13 inch od, 4 inch id 200 components per reel, maximum meets ansi/eia 481-2 carrier tape standards 1 4 5 8 0.098 [2.50] 0.018 [0.46] 0.391 [9.93] 0.082 [2.08] suggested pcb pad layout 0.046 [1.17] 0.098 [2.50] 0.395 [10.00] max 0.500 [12.70] max 0.286 [7.26] 0.380 [9.65] 0.390 [9.91] max dimensions are in inches [millimeters]. standard dimension tolerance is 0.005 [ 0.13 ] unless otherwise noted. orientation of com p onent inside pocket user feed direction
|