View BCT013_4815053.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

berex b c t013 http: //www.berex.com confidential 1500-4000 mhz medium power amplifier device features target device performance (t a = 25 c) symbols parameters test conditions min typ max unit gain 1900mhz 2140mhz 2400mhz 3500mhz 14.0 13.0 12.2 9.7 15.1 14.0 13.3 10.7 db s11 1900mhz 2140mhz 2400mhz 3500mhz -17.3 -12.0 -12.8 -25.3 db s22 1900mhz 2140mhz 2400mhz 3500mhz -12.8 -12.0 -12.9 -25.3 db oip3 1900mhz 2140mhz 2400mhz 3500mhz 42 42 40 37 45.0 45.2 43.1 40.2 dbm p1db 1900mhz 2140mhz 2400mhz 3500mhz 26.5 26.2 26.0 25.0 27.5 27.1 27.2 25.9 dbm nf 1900mhz 2140mhz 2400mhz 3500mhz 6.8 db ic vc = 5.0v 118 138 158 ma vc 5.0 v rth thermal resistance 50 c/w test conditions unless otherwise noted. 1. t = 25 c, vdevice = 5.0v, 50 ohm system. 2. oip3 is measured on an eval-board with two tones separated by 1 mhz. ? 45.0 dbm output ip3 at 13dbm/tone ? 15.0 db gain at 1900mhz ? 27.5 dbm p1db at 1900 mhz ? patented over voltage protection circuit ? application: commercial
berex b c t013 http: //www.berex.com confidential absolute maximum ratings parameter rating operating case temperature -40 to +85 c storage temperature -40 to +155 c junction temperature +250 c supply voltage 7 v input rf power 23dbm operation of this device above any of these parameters may result in permanent damage. typical device data s-parameters (vc=5v, ic=138ma, t=25 c) freq (50.00mhz to 4.000ghz) s(1,1) m1 freq=50.00mhz m2 freq=4.000ghz 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0.0 4.0 -50 -45 -40 -35 -30 -55 -25 frequency [ghz] s12 [db] 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0.0 4.0 0 2 4 6 8 10 12 -2 14 frequency [ghz] s21 [db] freq (50.00mhz to 4.000ghz) s(2,2) m1 freq=50.00mhz m2 freq=4.000ghz
berex b c t013 http: //www.berex.com confidential s-parameter test circuit generic pf083 evaluation board i-v characteristics pcb 31mil thick fr-4 ? current drop in between 5~6v is due to patented protection circuit.
berex b c t013 http: //www.berex.com confidential s-parameter (5v/135ma) freq s11 s11 s21 s21 s12 s12 s22 s22 [mhz] [mag] [ang] [mag] [ang] [mag] [ang] [mag] [ang] 100 -0.046 -30.149 2.219 -128.4 -41.958 66.107 -3.497 165.97 500 -0.952 -116.77 6.737 -174.18 -32.703 25.318 -3.457 162.64 1000 -1.111 -162.01 13.26 161.56 -32.513 76.255 -7.557 117.5 1500 -0.928 157.99 10.718 121.35 -30.171 46.516 -7.780 127.17 2000 -1.240 129.31 9.181 101.55 -28.599 42.527 -7.262 116.25 2500 -1.390 104.6 8.334 81.201 -26.76 37.808 -7.180 97.537 3000 -1.669 82.694 6.491 66.725 -26.706 32.623 -7.38 74.648 3500 -1.989 60.455 6.124 51.795 -25.792 26.141 -7.336 50.666 4000 -2.281 37.752 5.024 33.795 -24.653 20.698 -6.823 32.131 application circuit: 1900 mhz schematic diagram bom tolerance c3 c1 c2 l1 c4 c6 c5 c7 rf in rf out vcc bt013 c1 100pf 5% c2 1000pf 5% c3 10uf 15% c4 22pf 5% c5 22pf 5% c6 3.0pf 5% c7 0.5pf 5% l1 100nh 5% note: 1. chip is mounted on the pf083 open pkg, and bonded with 2-wires at both input and output. 2. pcb: 31mil thick fr4 3. distance between the center of the shunt cap(c6) and the input pin of bt013 is 3.2mm 4. distance between the center of the shunt cap(c7) and the output pin of bt03 is 8.3mm
berex b c t013 http: //www.berex.com confidential typical performance
berex b c t013 http: //www.berex.com confidential application circuit: 2100 mhz schematic diagram bom tolerance c3 c1 c2 l1 c4 c6 c5 c7 rf in rf out vcc bt013 c1 100pf 5% c2 1000pf 5% c3 10uf 15% c4 24pf 5% c5 24pf 5% c6 3pf 5% c7 0.5pf 5% l1 33nh 5% note: 1. chip is mounted on the pf083 open pkg, and bonded with 2-wires at both input and output. 2. pcb: 31mil thick fr4 3. distance between the center of the shunt cap(c6) and the input pin of bt013 is 1.5mm 4. distance between the center of the shunt cap(c7) and the output pin of bt03 is 6.4mm
berex b c t013 http: //www.berex.com confidential typical performance
berex b c t013 http: //www.berex.com confidential application circuit: 2400mhz schematic diagram bom tolerance c1 100pf 5% c2 1000pf 5% c3 10uf 15% c4 100pf 5% c5 100pf 5% c6 2pf 5% c7 0.5pf 5% l1 33nh 5% note: 1. chip is mounted on the pf083 open pkg, and bonded with 2-wires at both input and output. 2 pcb: 31mil thick fr4 3 distance between the center of the shunt cap(c6) and the input pin of bt013 is 0.7mm 4 distance between the center of the shunt cap(c7) and the output pin of bt03 is 3.2mm
berex b c t013 http: //www.berex.com confidential typical performance
berex b c t013 http: //www.berex.com confidential application circuit: 3500mhz schematic diagram bom tolerance c1 22pf 5% c2 0.75pf 5% c3 0.5pf 5% c4 100pf 5% c5 1000pf 5% c6 10uf 20% c7 0.5pf 5% c8 22pf 5% l1 33nh 5% note: 1. chip is mounted on the pf083 open pkg, and bonded with 2-wires at both input and output. 2 pcb: 31mil thick fr4 3 distance between the center of the shunt cap(c2) and the input pin of bt013 is 10mm 4 distance between the center of the series cap(c3) and the input pin of bt013 is 4mm 5 distance between the center of the shunt cap(c7) and the output pin of bt03 is 3mm
berex b c t013 http: //www.berex.com confidential typical performance
berex b c t013 http: //www.berex.com confidential die outline notes: 1) die thickness 100um 2) bondpad metal thickness 2.8um 3) backside metal au, 5um 4) device is grounded through via holes msl / esd rating esd rating value test standard msl rating standard class 1 passes <1000v human body model (hbm) jedec standard jesd22-a114b level 1 at +265 c convection reflow jedec standard j-std-020
berex b c t013 http: //www.berex.com confidential nato cage code: notice berex corporation reserves the right to make changes of product specification or to discontinue product at any time without notice. 2 n 9 6 f

▲Up To Search▲

Price & Availability of BCT013

	To Download BCT013 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .