flats (180 apart) 9/16" wrench mark: 7763-4-3 (date code) 5.254 133.45 .905 22.99 .804 20.42 flats (180 apart) 3/4" wrench catalog p/n: 7763-4-3 contacts: .000100 min gold per astm b488 over copper flash per astm b73 4 (rohs) 4. electrical specifications: low voltage contacts: 42 - 60 vac, 1 amp aux electrical contacts: 600 vac, 10 amp 5. environmental: operating temperature rating: -40c to 75c non-operating/storage temperture rating: -40c to 8 5c humidity: <95 rh (at 40c) .000080 min nickel per ams-qqn -290 (rohs) crimp sleeve: .000100 min nickel per ams-qq-n-290 o ver notes: unless otherwise specified 1. interface compliant to smpte 304 specificat ion. 2. material specifications: contacts: copper alloy alignment pins: brass per astm b16 crimp sleeve: phos. bronze o-rings and strain relief: silicone rubber all plastic parts: 20% glass filled polypropylene all other metal parts: 303 stainless steel per astm a582 3. finish specifications: stainless steel parts: passivate 6. optical: wavelength: 1100nm - 1350nm insertion loss: 0.3db typical, 0.5db max return loss: > -45db, -50db typical 7. replacement kits: contact kit: 7760-000-00709z 8. cable preparation and stripping procedure: cap-e05. 9. optional environmental boot 7760-000-00705z sold separately. 10. red ldpe dust cap included (not shown) 11. crimp tooling: for factory application use hand tool kth-1000 and die kth-2035 for field application use hand tool kth-5000 and di e kth-5018 angle xxx 62 barnes industrial road north 01/07/10 kfc date appd by er30231 description 05 rev 04/07/10 jcf date approved xx/xx/xx xxx date approved 04/07/10 wpm date approved 04/06/10 psm date drawn revised per sales drawing customer wallingford, connecticut 06492 .xxx [x.xx] .005 [0.13] .xxxx [x.xxx] .xxxx angles: 2 scale: 1:1 per asme y14.5m-1994 unless otherwise specified: dimensions are in inches [mm] tolerances: decimal: .xx [x.x] .01 [0.3] winchester electronics corporation third dmf026 b 2 a 1 pre-polished sht rev of 05 tri-loc, smpte 304, receptacle sd7763-4-3
replacement component ordering numbers 13 11 5 6 2 3 4 1 9 10 7 8 12 xxx kfc 01/07/10 by date appd revised per er30231 description 05 rev 04/07/10 jcf date approved xx/xx/xx xxx date approved 04/07/10 wpm date approved 04/06/10 psm date drawn customer sales drawing per asme y14.5m-1994 unless otherwise specified: dimensions are in inches [mm] tolerances: decimal: .xx [x.x] .01 [0.3] .xxx [x.xx] .005 [0.13] .xxxx [x.xxx] .xxxx angles: 2 scale: 1:1 winchester electronics corporation 62 barnes industrial road north wallingford, connecticut 06492 third angle dmf026 b a tri-loc, smpte 304, receptacle pre-polished sht rev of 05 2 2 sd7763-4-3 catalog p/n: 7763-4-3 item no. part no. description 7763-4- 3/qty. plating code(s) 13 vnfps01-900-34 splice protector sleeve, 34mm 50 12 VNSC-748U red ldpe dust cap 25 11 7760-000-00711z fiber optic connector stub 2 10 78-0102u #4-40 hex set screw 10 9 78-1012u strength member support clamp 10 8 78-3011u jack insulator half side "b" 25 7 78-3010u jack insulator half side "a" 25 6 78-4204u jack male crimp contact 50 5 78-4203u jack female crimp contact 50 4 78-0705u rear o-ring 25 3 78-0701u rear cable seal 25 2 78-0301u washer for rear cable seal 25 1 1-8156u crimp sleeve (cable shield ferrule) 25
|