View M150EW01-V0_4249034.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation product specification document version 0.1 1/18 (v ) preliminary specifications ( ) final specifications module 15.0 wxga color tft-lcd model name m150ew01 v0(non-glare) customer date checked & approved by note: this specification is subject to change without notice. approved by date prepared by desktop display business group / au optronics corporation www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 2/18 contents 1. handling precautions..............................................................4 2. general description.................................................................5 2.1 general specification......................................................................................................................5 2.2 optical characteristics....................................................................................................................6 3. functional block diagram.......................................................10 4. absolute maximum ratings....................................................11 4.1 absolute ratings of tft lcd module..........................................................................................11 4.2 absolute ratings of backlight unit................................................................................................11 4.3 absolute ratings of environment..................................................................................................11 5. electrical characteristics........................................................12 5.1 tft lcd module........................................................................................................................12 5.2 backlight unit..............................................................................................................................13 6. signal characteristic................................................................. 6.1 pixel format image.......................................................................................................................... 6.2 the input data format....................................................................................................................... 6.3 signal description/pin assignment.................................................................................................... 6.4 interface timing............................................................................................................................... 7. connector description............................................................15 7.1 tft lcd module........................................................................................................................15 7.2 backlight unit..............................................................................................................................15 7.3 signal for lamp connector...........................................................................................................15 8. reliability test.......................................................................16 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 3/18 record of revision version and date page old description new description remark 0.1 2007/08/13 all first edition for auo internal www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 4/18 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spot. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open or modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the ccfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure, do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit (iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 5/18 2. general description m15 0 ew01 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga (1280(h) x 720 (v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. inverter of backlight is not included. 2.1 general specification the following items are characteristics summary on the table at 25 condition: item unit specification remark screen diagonal [mm] 381 15.0 inch active area [mm] 332.16(h) 186.84(v) maximum resolution - 1280x3(rgb) x 720 pixel pitch [mm] 0.2595 pixel arrangement - r.g.b. vertical stripe display mode - tn, normally white white luminance (center) [cd/m 2 ] 200* contrast ratio - 400:1 optical response time [ms] 8* tr+tf color saturation % 45% nominal input voltage vdd [voltage] 3.3 power consumption [watt] 14.4* 2 ccfl weight [grams] 1150* physical size [mm] 354.1 (h) x 227.4 (v) x 12 (d)* electrical interface - 1channel lvds support color - 16.7m (6bit+hi-frc) [ o c] 0 ~ +50 operating temperature range [ o c] -20 ~ +60 storage surface treatment - anti-glare viewing angle [ o ] 90/50 [x] 0.313* +/-0.03 color / chromaticity coordinates (cie) [y] 0.329* +/-0.03 uniformity [%] 80* * based on engineer s estimation, and are subject to change w/o notice. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 6/18 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature) : item unit conditions min. typ. max. note white luminance iccfl=6.5ma [cd/m 2 ] 160 200 - 4 horizontal (right) cr = 10 (left) - - 45 45 - - viewing angle [degree] vertical (upper) cr = 10 (lower) - - 15 35 - - 1 luminance uniformity [ % ] 9 points 70% 80% 2,3 cr: contrast ratio 240 400 - 4 cross talk [ % ] 4 5 rising - 5 falling - 3 response time [msec] rising + falling 8 4,6 red x tbd tbd tbd red y tbd tbd tbd green x tbd tbd tbd green y tbd tbd tbd blue x tbd tbd tbd blue y tbd tbd tbd white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 4 flicker [db] - -20 7 note 1. definition of viewing angle viewing angle is the measurement of contrast ratio 10 R and R 5, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 7/18 note 2: 9 points position note 3: the luminance uniformity of 9 points is defined by dividing the maximum luminance values by the minimum test point luminance minimum brightness of 9 points w9 = maximum brightness of 9 points 50 % 90 % 90 % 50 % 10 % 10 % www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 8/18 note 4: measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 5 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 9/18 note 6: definition of response time: the output signals of photo detector are measured when the input signals are changed from full black to full white (rising time), and from full white to full black (falling time), respectively. the response time is interval between the 10% and 90% of amplitudes. please refer to the figure as below. note 7: subchecker pattern r g b r g b r g b r g b r g b r g b method: record dbv & dc value with (westar)trd-100 level dc hz) 30 level(at ac log 20 (db) flicker = gray level = l127 gray level = l0 amplitude time dc ac www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 10/18 3. functional block diagram the following diagram shows the functional block of the 15.4 inches wide color tft/lcd module: tft-lcd 1280(x3) x 720 pixels g1 g800 d1 d3840 2 ccfl inverter dc power c o n n e c t o r dc/dc converter lvds receiver timing controller gamma correction auo asic lvds i/f + x - pcb +3.3v www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 11/18 4. absolute maximum ratings absolute maximum ratings of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 7.5 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating top 0 +50 [ o c] note 3 operation humidity hop 5 90 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 90 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to auo iis(incoming inspection standard). operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 12/18 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows: symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power tbd [watt] note 1 idd idd current 350 450 [ma] note 1 i rush inrush current 2000 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition black patterm note 2 measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d 2 s d 1 d 5 d 6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 13/18 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of thc63lvdf84a(thine electronics inc.) in detail. signal electrical characteristics are as follows: parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform 5.2 backlight unit parameter guideline for ccfl inverter is under stable conditions at 25 (room temperature) : parameter min typ max units condition ccfl standard current (i scfl ) 7.0 7.5 8.0 [ma] rms ccfl operation current (i rcfl ) 3.0 8.0 8.0 [ma] rms note 2 ccfl frequency (f cfl ) 40 50 80 [khz] note 3,4,8 ccfl ignition voltage (v icfl , ta= 0 ) [volt] rms ccfl ignition voltage (v icfl , ta= 25 ) [volt] rms note 5 ccfl voltage (v cfl ) [volt] rms note 6 ccfl power consumption (p cfl ) [watt] note 6 vth vtl vcm vss www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.1 14/18 ccfl life time (lt cfl ) 40,000 50,000 - [hour] note 7 note 1: typ. are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying ignition voltage for 1 [sec] until discharge. *5 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has duty dimming , if i rcfl is less than 3ma. note 3: ccfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1290 voltage. lamp units need 1290 voltage minimum for ignition. note 6: the variance of ccfl power consumption is 10%. calculator value for reference (i scfl v cfl 2= p cfl ) note 7: definition of life: brightness becomes 50%. the typical life time of ccfl is under the condition at 6.5 ma lamp current. note 8: requirement for system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp. it should help increase the lamp lifetime and reduce its leakage current. the frequency range will not affect to lamp lifetime and reliability characteristics. (reference value) the rate of unsymmetrical of lamp lighting waveform is shown (lamp current waveform and lamp voltagewaveform) at 5% or less. asymmetrical ( O a O - O b O ) / O c OQ 5 % a lamp current or lamp voltage o-p of +side b lamp current or lamp voltage o-p of C side c max(a,b) this is bigger in a or b recommendation lighting frequency 50 ~ 60 khz www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 15/18 7. connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number tbd mating housing/part number tbd 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer cvilux type / part number cp0502sl09 mating type / part number cp0502p1ml0-lf 7.3 signal for lamp connector connector no. pin no. input color function 1 hot1 pink high voltage upper cn1 2 cold1 white low voltage connector no. pin no. input color function 1 hot1 pink high voltage lower cn2 2 cold1 white low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 16/18 8. reliability test items required condition note temperature humidity bias (thb) ta= 50, 80%rh, 300hours high temperature operation (hto) ta= 50, 50%rh, 300hours low temperature operation (lto) ta= 0, 300hours high temperature storage (hts) ta= 60, 300hours low temperature storage (lts) ta= -20, 300hours vibration test (non-operation) acceleration: 1.5 g wave: random frequency: 10 - 200 - 10 hz sweep: 30 minutes each axis (x, y, z) shock test (non-operation) acceleration: 50 g wave: half-sine active time: 20 ms direction: x, y, z (one time for each axis) drop test height: 60 cm, package test thermal shock test (tst) -20 /30min, 60 /30min, 100 cycles 1 on/off test on/10sec, off/10sec, 30,000 cycles contact discharge: 8kv, 150pf(330 ) 1sec, 8 points, 25 times/ point. esd (electro static discharge) air discharge: 15kv, 150pf(330 ) 1sec 8 points, 25 times/ point. 2 altitude test operation:10,000 ft non-operation:30,000 ft note 1: the tft-lcd module will not sustain damage after being subjected to 100 cycles of rapid temperature change. a cycle of rapid temperature change consists of varying the temperature from -20 to 60, and back again. power is not applied during the test. after temperature cycling, the unit is placed in normal room ambient for at least 4 hours before power on. note 2: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost. self-recoverable. no hardware failures. www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 17/18 pin assignment pin no. symbol function pin no. symbol function 1 vdd 3.3v 11 rxin2- lvds signal 2 vdd 3.3v 12 rxin2+ lvds signal 3 vss ground 13 vss ground 4 vss ground 14 rxclk- lvds signal 5 rxin0- lvds signal 15 rxclk+ lvds signal 6 rxin0+ lvds signal 16 vss ground 7 vss ground 17 rxin3- lvds signal 8 rxin1- lvds signal 18 rxin3+ lvds signal 9 rxin1+ lvds signal 19 agmode active high/ground 10 vss ground 20 hvs active high/ground www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 18/18 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of M150EW01-V0

	To Download M150EW01-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .