spec no: dsac0154 rev no: v.2 date: may/21/2003 page: 1 of 4 approved: j. lu checked: allen liu drawn: z.y.yang 2.0x1.25mm smd chip led lamp notes: 1. all dimensions are in millimeters (inches).2. tolerance is 0.1(0.004") unless otherwise noted. 3. specifications are subject to change without notice. features l 2.0mmx1.25mm smt led, 0.75mm thickness. l low power consumption. l wide viewing angle. l ideal for backlight and indicator. l various colors and lens types available. l package : 2000pcs / reel. package dimensions KPTK-2012MWC white description the source color devices are made with gan on sic light emitting diode.static electricity and surge damage the leds. it is recommended to use a wrist band or anti- electrostatic glove when handling the leds. all devices, equipment and machinery must be electrically grounded. attention observe precautions for handling electrostatic discharge sensitive devices
spec no: dsac0154 rev no: v.2 date: may/21/2003 page: 2 of 4 approved: j. lu checked: allen liu drawn: z.y.yang selection guide note: 1 . 1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. electrical / optical characteristics at t a =25 c absolute maximum ratings at t a =25 c note: 1. 1/10 duty cycle, 0.1ms pulse width. r e t e m a r a pre te m a r a p r e t e m a r a p r e t e m a r a pre te m a r a pet ih w et i h w e t i h w e t i h wet ih wst in u st i n u s t i n u s t i n ust in u n o i t a p i s s i d r e w o p50 1wm t n e r r u c d r a w r o f c d03am ] 1 [ t n e r r u c d r a w r o f k a e p05 1am e g a t l o v e s r e v e r5v e r u t a r e p m e t e g a r o t s / g n i t a r e p o04 - 5 8 + o t c c . o n t r a p.o nt r a p . o n t r a p . o n t r a p.o nt r a pec id ec i d e c i d e c i dec i dep yt s n e lep yt s n e l e p y t s n e l e p y t s n e lep yt s n e l ) d c m ( v i)d cm ( v i ) d c m ( v i ) d c m ( v i)d cm ( v i a m 0 2 @ g n i w e i vgn iw e i v g n i w e i v g n i w e i vgn iw e i v e l g n a . n i m.n i m . n i m . n i m.n i m.p yt . p y t . p y t . p y t.p y t 2 / 1 22/ 1 2 2 / 1 2 2 / 1 22/ 1 2 c w m 2 1 0 2 - k t p k)n ag ( e t i h wra el c r e t a w 81 04 0 0 1 l o b m y slo bm y s l o b m y s l o b m y slo bm y sre te m a r a pre te m a r a p r e t e m a r a p r e t e m a r a pre te m a r a pec iv e dec iv e d e c i v e d e c i v e dec iv e d.p yt . p y t . p y t . p y t.p y t.x am . x a m . x a m . x a m.x a mst in u st i n u s t i n u s t i n ust in usn oi t i d n o c t s e tsn oi t i d n o c t s e t s n o i t i d n o c t s e t s n o i t i d n o c t s e tsn oi t i d n o c t s e t v f e g a t l o v d r a w r o fet ih w8. 35. 4v i f a m 0 2 = i r t n e r r u c e s r e v e ret ih w -01au v r v 5 = x s e t a n i d r o o c y t i c i t a m o r h cet ih w 3 3 . 0-- - y43 .0 - - - cec na t i c a p a cet ih w00 1fpv f z h m 1 = f , v 0 =
spec no: dsac0154 rev no: v.2 date: may/21/2003 page: 3 of 4 approved: j. lu checked: allen liu drawn: z.y.yang white KPTK-2012MWC
spec no: dsac0154 rev no: v.2 date: may/21/2003 page: 4 of 4 approved: j. lu checked: allen liu drawn: z.y.yang recommended soldering pattern (units : mm) tape specifications (units : mm) KPTK-2012MWC smt reflow soldering instructions number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first andsecond soldering process.
|
