engineering bulletin conductive polymer aluminum solid capacitors no.740a / nov.2003 tentative nippon chemi-con corporation 1190 1 @ super low esr, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. @ suitable for dc-dc converters, voltage regulators and decoupling applications. @ endurance with ripple current : 125 c 1000 hours @ rated voltage range : 2.5 to 20v dc , capacitance range : 22 to 1000 m f @ case size range : f 6.3 b 6.0mm to f 10 b 8.0mm ? specifications (at 20 c , 120hz) (at 105 c ) (at 20 c after 2 minutes) (at 20 c , 120hz) (at 100khz) category temperature range rated voltage range capacitance tolerance surge voltage leakage current dissipation factor (tan e ) low temperature characteristics (max. impedance ratio) endurance bias humidity surge voltage failure rate items - 55 to +125 c 2.5 to 20v dc p 20% (m) rated voltage b 1.15v shall not exceed value shown in standard ratings. 0.12 max. z( - 25 c )/z(+20 c ) [ 1.15 z( - 55 c )/z(+20 c ) [ 1.25 the following specifications shall be satisfied when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 125 c . appearance no significant damage capacitance change [p 20% of the initial value df (tan e ) [ 200% of the initial specified value esr [ 200% of the initial specified value leakage current [ the initial specified value the following specifications shall be satisfied when the capacitors are restored to 20 c after subjecting them to the dc rated voltage at 60 c , 90 to 95% rh for 1000 hours. appearance no significant damage capacitance change [p 20% of the initial value df (tan e ) [ 150% of the initial specified value esr [ 150% of the initial specified value leakage current [ the initial specified value the capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105 c for 30 seconds through a protective resistor(r=1k o ) and discharge for 5 minutes 30 seconds. appearance no significant damage capacitance change [p 20% of the initial value df (tan e ) [ 150% of the initial specified value esr [ 150% of the initial specified value leakage current [ the initial specified value 1% per 1000 hours maximum (confidence level 60%) characteristics ? part numbering system ? dimensions [mm] f d p 0.5 l p 0.3 0.3max. a p 0.2 w c p 0.2 b p 0.2 p case code f60 h70 j80 f d 6.3 8 10 l 5.7 6.7 7.7 a 6.6 8.3 10.3 b 6.6 8.3 10.3 c 7.2 9.0 11.0 w 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 p 1.9 3.1 4.5 pxh 20 vc 22 m f60 case code cap tolerance ( p 20%) nominal cap code terminal type rated voltage in volts series name capacitance 39 m f 100 m f 220 m f code 39 100 220 ? marking h 39f 22 20 v ex) pxh20vc22mf60 *note : if any doubt arises, measure the leakage current after following voltage treatment. voltage treatment : dc rated voltage are applied to the capacitors for 120 minutes at 125 c . feature ! pb free type specifications in this bulletin are subject to change without notice. please ask us for technical specifications before purchase and use.
engineering bulletin conductive polymer aluminum solid capacitors no.740a / nov.2003 tentative nippon chemi-con corporation 1190 2 ? standard ratings case code f60 h70 j80 leakage current ( m amax) esr (m o max/ 20 c ,100k to 300khz) rated voltage (v dc ) nominal capacitance ( m f) rated ripple current (marms/100k to 300khz) -55 to +105 c +105 to +125 c 2.5 4 6.3 6.3 10 16 20 2.5 4 6.3 6.3 10 10 16 20 2.5 4 6.3 10 16 16 20 220 150 82 100 56 39 22 560 220 150 220 120 150 82 47 1000 470 330 330 150 180 82 110 120 103 126 112 125 88 280 176 189 277 240 300 262 188 500 376 416 660 480 576 328 35 35 40 40 45 50 60 30 30 30 30 35 35 40 45 25 25 25 30 35 35 45 2500 2450 2400 2400 2250 2050 1650 3100 3020 3020 3020 2800 2800 2700 2000 3700 3700 3700 3700 3020 3020 2400 770 770 720 720 680 650 590 960 960 960 960 880 880 830 780 1100 1100 1100 1010 930 930 820 ? recommended reflow soldering conditions 200 230 peak 150 25 preheat 120sec. max. peak temperature time (sec.) t 2 t 1 ( c ) temperature on the top of capacitor and temperature of capacitor terminal @ reflow profile method : air or infrated reflow [the times of reflow soldering : once] peak temperature : 250 c max. max. period of time over 230 c (t 1 ) : 40 sec.max. max. period of time over 200 c (t 2 ) : 60 sec.max. preheat : 150 c , 120 sec. max. [the times of reflow soldering : twice] peak temperature : 250 c max. max. period of time over 230 c (t 1 ) : 30 sec.max. max. period of time over 200 c (t 2 ) : 50 sec.max. preheat : 150 c , 120 sec. max. @ conditions specifications in this bulletin are subject to change without notice. ? recommended solder land on pc board c b a solder land on pc board case code e60 f60 h70 a 1.4 1.9 3.1 b 3.0 3.5 4.2 c 1.6 1.6 2.2
|
