specification scp-1k2-05 order no. safety model no. dc voltage rated current current range rated power ripple & noise (max.) note.2 output voltage adj. range voltage tolerance note.3 line regulation load regulation setup, rise, hold up time voltage range frequency range efficiency (typ.) power factor input environment inrush current (max.) leakage current (max.) over temperature safety standards safety & emc (note. 5) working temp. working humidity storage temp., humidity temp. coefficient vibration power good signal special function dimension others note packing overload note. 4 over voltage protection ac current 1k2s-p005 5v 200a 0 ~ 200a 1000w 100mvp-p 3.0% typical adjustment by potentiometer 20%~100% adjustment by 1~ 5vdc external control 2.0% 0.5% 1.5% 500ms, 200ms, 16ms at full load 180 ~ 260vac 260 ~ 370vdc see the derating curve 47 ~ 63hz 80% >0.98 / 230vac 10a / 230vac 60a / 230vac 3.5ma / 240vac 110 ~ 135% follow to output set up point >100 / measure by heat sink, near transformer ul60950, tuv en60950-1 approved harmonic current ems immunity compliance to en55022 (cispr22) class a compliance to en61000-3-2,3 compliance to en61000-4-2,3,4,5,6,8,11, light industry level , criteria a withstand voltage isolation resistance -20 ~ +65 (refer to output load derating curve) 20 ~ 90% rh non-condensing -20 ~ +85 , 10 ~ 95% rh 0.04% / (0 ~ 50 ) 10 ~ 200hz, 2g 10min./1cycle, 60min. each along x, y, z axes open collector of npn transistor dc voltage adj., remote sensing, remote control, parallel operatio n(refer to control terminal instruction manual) 290*120*132mm (l*w*h) 5kg; 4pcs /21kg /carton 84% 0.5% 0.5% 1.0% 120mvp-p 1k2s-p012 12v 100a 0 ~ 100a 1200w scp-1k2-12 82% 1.0% 0.5% 1.5% 100mvp-p 1k2s-p009 9v 133a 0 ~ 133a 1197w scp-1k2-09 85% 0.5% 0.5% 1.0% 150mvp-p 1k2s-p015 15v 80a 0 ~ 80a 1200w SCP-1K2-15 89% 0.5% 0.5% 1.0% 240mvp-p 1k2s-p024 24v 50a 0 ~ 50a 1200w scp-1k2-24 86% 0.5% 0.5% 1.0% 180mvp-p 1k2s-p018 18v 66.6a 0 ~ 66.6a 1198w scp-1k2-18 90% 0.5% 0.5% 1.0% 480mvp-p 1k2s-p048 48v 24a 0 ~ 24a 1152w scp-1k2-48 90% 0.5% 0.5% 1.0% 500mvp-p 1k2s-p060 60v 20a 0 ~ 20a 1200w scp-1k2-60 89% 0.5% 0.5% 1.0% 360mvp-p 1k2s-p036 36v 33.3a 0 ~ 33.3a 1198w scp-1k2-36 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. current limiting 3 times(1.5s,3.0s,5.0s)then intelligent aut o recovery before shut down 5. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still mee ts emc directives. file name: scp-1k2-spec 2008-05-06 105 ~ 140% rated output power features : protection type : shut down o/p voltage, re-power on to recover protection type : current limiting, delay shut down o/p voltage, re-pow er on to recover emi conduction & radiation cooling by fan, >20% load or >50 fan on mtbf 37.4k hrs min. mil-hdbk-217f(25 ) i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, op/fg:100m ohms / 500vdc / 25 / 70% rh protection type : shut down o/p voltage, recovers automatically afte r temperature goes down ac input 180~260vac only pf> 0.98@ 230vac protections: short circuit / overload / over voltage / over temperature built in remote sense function built-in remote on-off control built-in power good signal output built-in parallel operation function(n+1) can adjust from 20~100% output voltage by external control 1-5v forced air cooling by built-in dc fan 3 years warranty s c p - 1 k 2 s e r i e s 900~1200w parallel (n+1) with pfc function
file name: scp-1k2-spec 2008-05-06 mechanical specification derating curve control terminal pin no. assignment (tb1) : dinkle 51hdbc-o8p or equi valent pin no. pin no. 5 1 6 2 78 34 assignment assignment pg vs+ par vs- gnd inh vci vco mating with dinkle 51sdb-o8p or equivalent unit:mm ambient temperature ( ) input voltage (vac) 60hz 1800 1600 1400 800 1000 1200 1100 600 load (%) output power (w) ta=25 terminal pin no. assignment pin no. 13 2 assignment fg ac/n ac/l 90 110 130 150 180 200 220 240 260 160 ac input 1 3 2 m3(nut) 3h-4 89 m3(nut) 3h-4 #6-32-4 1 2 3 4 5 6 7 8 led pos+ neg- 120 132.5 200 103 200 26.5 290 251 led vadj tb1 30 air flow direction 10 -20 -10 20 30 40 50 60 70 20 40 60 80 100 s c p - 1 k 2 s e r i e s 900~1200w parallel (n+1) with pfc function
file name: scp-1k2-spec 2008-05-06 control terminal instruction manual parallel operation without remote sensing parallel operation with remote sensing on/off control by switch remote sensing load on/off control by transistor load on/off switch load l:off h:on load load using internal voltage control gnd inh vs+ vco pg par vci vs- load inh par gnd vco pg vs- vci vs+ inh gnd par pg vco vci vs- vs+ vco par gnd pg inh vs- vci vs+ vco gnd inh pg par vs- vci vs+ vco par inh gnd pg vs+ vci vs- vs- vci vs+ pg gnd inh par vco vco par gnd inh pg vs+ vs- vci vco inh gnd pg par vs- vci vs+ pg inh gnd par vs+ vs- vci vco good :ledon dc 1-5v output voltage adjust with dc 1-5v load vs+ vs- vci vco par gnd inh pg load inh par gnd vco pg vs- vci vs+ 40v / 0.5a max. : led off fail power good signal 123456 o.v.p. 120% (typ.) v vout 100 120 40 60 80 20 output voltage (%) external voltage (dc) non-linear scp-1k2 series 900~1200w parallel (n+1) with pfc function
|
