View ALL4XXAND9XX_3263397.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

application note nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 1 of 16 february 2000 small loop antennas 1. general for rf designers developing low-power radio devices for short-range applications, antenna design has become an important issue for the total radio system design. taking the demand for small size and low cost into account in the development of such radio modules, a small-tuned loop antenna on the same printed circuit board as the radio module is a good solution. an overview of the basics for electrically small loop antennas is presented. the overview is mainly based on reference [1]. an effective shunt-matching technique for loop antennas, the t-match, is also discussed. four different loop antennas for 433 mhz have been fabricated, and impedance and gain measurements have been made on these antennas in an antenna laboratory. 2. loop antenna basics electrically small loop antennas are antennas where the circumference is less than about one-tenth of a wavelength [1]. the field pattern of such loop antennas is similar to that of an infinitesimal dipole with a null perpendicular to the plane of the loop and with its maximum along the plane of the loop. this chapter describes the geometry and the electrical equivalent circuit for a rectangular loop antenna. physical dimensions for the antenna is used to calculate the components in the antenna equivalent circuit and the antenna efficiency. the t-matching method is presented in order to match the impedance of the antenna to a transmitter/receiver. formulas for range calculation is also presented in order to make the designer of radio modules for short range applications able to calculate either the range for a device or the power needed for a specified range. nan400-03
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 2 of 16 february 2000 2.1. loop antenna physical parameters figure 1 shows the geometry of the rectangular loop antenna. z ant p rf b 1 b 2 loop conductor c1 a 1 a 2 d s c2 rq figure 1 . geometry of rectangular loop antenna the loop antenna physical parameters used in the calculations are a 1 = loop antenna width [m] a 2 = loop antenna length [m] b 1 = thickness of loop conductor [m] b 2 = width of loop conductor [m] for loop antenna fabricated on a printed circuit board (pcb), the thickness of the loop conductor b 1 means the thickness of the copper layer on top of the substrate. during calculation of the antenna electrical parameters, the rectangular loop has to be modelled as an equivalent quadratic loop, and the planar loop conductor has to be modelled as a wire conductor with equivalent circular radius. from the parameters above the equivalent quadratic sides of the loop are given by [ ] m a a a 2 1 = the calculated equivalent quadratic sides are used in the formulas below for the loop area a , and the inductances l a and l i . the loop area is given by [ ] 2 2 m a a = the equivalent electrical circular radius of the loop conductor is given by
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 3 of 16 february 2000 [ ] m b b b 2 1 24 . 0 35 . 0 + = in electrostatic, the equivalent radius represents the radius of a circular wire whose capacitance is equal to that of the noncircular geometry, see [1] table 9.3 pp. 456. 2.2. loop antenna electrical equivalent circuit to be able to estimate the capacitor c p used to resonate the antenna, the input impedance of the loop antenna has to be determined. to estimate the antenna efficiency, radiation resistance, loss resistance of the loop conductor and other ohmic losses has to be determined. according to [1] the equivalent circuit for the input impedance of a small loop when the loop is used as a transmitting antenna is shown in figure 2 . z g + _ v g z' in c p r l x i r r x a r x z in figure 2 . loop antenna equivalent circuit (transmit mode). the loop antenna input impedance z in is given by: ( ) ( ) [ ] w + + + + = i a x l r in l l f j r r r z 0 2 p where r r = radiation resistance [ ] r l = loss resistance of loop conductor [ ] rx = additional ohmic losses (esr in capacitor c p etc.) [ ] l a = inductance of loop antenna [h] l i = inductance of loop conductor [h] the radiation resistance is given by [ ] w ? ? ? ? ? ? 4 2 31171 l a r r where
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 4 of 16 february 2000 [ ] m f c 0 = l where c is the speed of light equal to 3 10 8 m/s f 0 is the resonance frequency in hz. the loss resistance of the loop inductor is given by [ ] w + + = = s m p 0 0 2 1 2 1 f b b a a r p l r s l where l = length of the metal loop conductor p = perimeter of the cross section of the loop conductor r s = conductor surface resistance m 0 = 10 -7 h/m s = conductivity of the conductor equal to 5.8 10 7 s/m for copper. the additional ohmic losses that is introduced mainly because of esr (equivalent series resistance) of the capacitor c p is given by ( ) [ ] w - - + = l r i a x r r q l l f r 0 2 p as can be seen from the above expression, the maximum possible quality factor q of a loop antenna is mainly determined by the esr (i.e. the quality factor) of the capacitor c p . a resistor r q in parallel with c p can be used to control the q -value of the antenna. the insertion of this parallel resistor will reduce the antenna input impedance. in figure 2 the capacitor c p is used in parallel to z in to resonate the antenna, that is to cancel out the imaginary part of the input impedance z in at the operating frequency. c p can also be used to represent distributed stray capacitances. it can be shown that the parallel capacitor c p at resonance is given by [ ] [ ] f l l f r r r l l c i a x l r i a p 2 2 ) ( 2 ) ( + + + + + = p under resonance the input impedance ' in z can be shown to be equal to ( ) [ ] [ ] w + + + + + + = x l r i a x l r in r r r l l f r r r z 2 ' 2 p
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 5 of 16 february 2000 the inductive reactance x a of the loop is computed using the inductance l a of, [1] circular loop of radius a and wire radius b: [ ] h b a a l a ? ? - ? ? ? ? = 2 8 ln 0 m square loop with sides a and wire radius b: [ ] h b a a l a ? ? - ? ? ? ? = 774 . 0 ln 2 0 p m the reactance x i of the loop conductor can be computed using the inductance l i of the loop. for a single turn this can be approximated by [2] [ ] h a a l i 2 0 m = where a is the area of the loop. the antenna efficiency can then be expressed as esr l r r r r r r + + = h alternatively ( ) i a r l l f qr + = 0 2 p h 2.3. impedance matching under resonance the resistive input impedance of the loop is high, and has to be transformed down to a lower value to match the transmitter output impedance/receiver input impedance. an effective shunt-matching technique is the t- match connection as shown in figure 1 . this method of matching is based on the fact that the impedance between any two points equidistant from the center along a resonant antenna is resistive, and has a value that depends on the spacing between the two points (feed length). it is therefore possible to choose a pair of points between which the impedance will have the right value to match the transmitter output impedance/receiver input impedance. by reducing the distance between the connection points the impedance is reduced. in practice, the transmitter/receiver cannot be connected directly at these points because the distance between them is much greater than the pin spacing of an integrated circuit. the t-match arrangement in figure 1 overcomes this difficulty by using a second conductor paralleling the
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 6 of 16 february 2000 antenna to form a matching section to which the transmitter/receiver may be connected. a trial and error procedure is used to vary the feed length to make the total input impedance of the loop antenna equal to the transmitter output impedance/receiver input impedance. the estimated capacitor c p must be tuned for maximum radiated power from the antenna for every position of the connection points. 2.4. antenna impedance and q-value with chip capacitors in the loop the antenna impedance is dependent of both feed length and q -value (read parallel resistor r q ). the q -value is independent of the impedance of the antenna, which means that one chooses a q -value and then chooses the feed length. to achieve reproducible values of transmitter power radiation and receiver sensitivity in mass production, the q -value of the antenna has to match the capacitors that will be used to tune the antenna to the right resonance frequency. the q -value of the loop should be chosen according to 1 100 1 1 - + = tol q the tol variable is the tolerance of the capacitors in %. the equation is based on the assumption that the variation in radiated power due to capacitor variations should be lower than 3db. if the tolerance is 4% the q -value will be 50. if a higher q -value is chosen, each antenna has to be tuned to keep the variation in radiated power lower than 3db. 2.5. range calculations rf systems operation in the uhf band are not restricted to the line-of-sight coverage of optical systems (ir systems) due to diffraction and reflection of radio waves at edges and conductive surfaces as well as their capability to penetrate dielectric materials. range calculation parameters are transmitter output power, p rf [dbm] transmitter and receiver antenna efficiency, h antenna separation, r [m] free-space loss, l p [db] additional propagation losses other than free-space loss, l x [db] receiver sensitivity, s [dbm]
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 7 of 16 february 2000 the free space propagation model is used to predict received signal strength when the transmitter and receiver have a clear, unobstructed line-of-sight path between them. the free-space loss factor l p is given by [ ] ? ? ? ? ? = ? ? ? ? ? = r db l r l p p p l p l 4 log 20 4 2 the free-space loss factor takes into account the losses due to the spherical spreading of the energy by the antenna. the equation shows that the received power will fall off as the square of the transmitter-receiver separation distance. this implies that the received power decays with distance r at a rate of 20 db/decade, (i.e. 6db extra loss for doubling of the distance). assuming reflection and polarisation-matched antennas, aligned for maximum directional radiation and reception, it can be shown that the communication range with given output power p rf , sensitivity s and equal tx/rx antennas is given by [ ] m p s r rf 2 4 h p l = this equation is based on the assumption that the two antennas are separated by a distance l / 2 2 d r > . d is the largest dimension of either antenna. wave guidance occurring along conductive surfaces may increase the operation range as well. the free-space path analysis applies to line-of-sight propagation, which means you have to correct for various other propagation losses l x such as signal reflection, diffraction, scattering and polarisation losses. when these losses are included, the communication range is given by [ ] m p l s r rf x 2 4 h p l = given the required range r , assumed losses l x , sensitivity s and equal tx/rx antennas, the necessary output power p rf is given by [ ] w l l s p p x rf 2 h =
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 8 of 16 february 2000 2.6. range calculation example given a rectangular loop antenna with dimensions a 1 = 30mm and a 2 = 50mm fabricated on a standard fr-4 substrate. the thickness of the copper layer on top of the substrate is b 1 = 35 m m and the width of loop conductor b 2 = 1mm. the antenna quality factor is limited to q = 50 by a resistor in parallel with the capacitor c p which is used to resonate the loop. the antenna operates at f 0 = 433.936mhz. 1. estimate the capacitor c p at resonance and the antenna efficiency. 2. calculate the free-space communication range assuming equal loop antennas as given above. the transmitter output power is 10dbm (10mw), and the receiver sensitivity is ?103dbm (0.05012 pw). solution: 1. to estimate the capacitor c p , the parameters l a , l i , r r , r l and r x has to be calculated. to calculate l a and l i , the equivalent quadratic sides, a , and the equivalent electrical circular cylinder radius of the loop conductor b , must be calculated first. m a a a 03873 . 0 05 . 0 03 . 0 2 1 = = = m b b b 00025 . 0 001 . 0 24 . 0 000035 . 0 35 . 0 2 24 . 0 1 35 . 0 = + = + = nh l b a a l a a 27 . 132 774 . 0 00025 . 0 03873 . 0 ln 03873 . 0 10 4 2 774 . 0 ln 2 7 0 = ? ? - ? ? ? ? = ? ? - ? ? ? ? = - p p p m nh a l i 33 . 24 03873 . 0 10 4 2 1 2 1 7 0 = = = - p m ( ) ( ) w = ? ? ? ? ? = ? ? ? ? ? ? 30710 . 0 6913 . 0 03873 . 0 03873 . 0 31171 31171 4 2 4 2 l a r r w = + + = + + = - 42008 . 0 10 8 . 5 10 4 10 936 . 433 001 . 0 000035 . 0 05 . 0 03 . 0 7 7 6 0 0 2 1 2 1 p p s m p f b b a a r l ( ) ( ) 42008 . 0 30710 . 0 50 10 33 . 24 10 27 . 132 10 936 , 433 2 2 9 9 6 0 - - + = - - + = - - p p x l r i a x r r r q l l f r w = 81222 . 7 x r
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 9 of 16 february 2000 then the capacitor c p can be calculated: [ ] ( ) ( ) [ ] pf c c l l f r r r l l c p p i a x l r i a p 86 . 0 10 33 . 24 10 27 . 132 10 936 . 433 2 81222 . 7 42008 . 0 30710 . 0 10 33 . 24 10 27 . 132 ) ( 2 ) ( 2 9 9 6 2 9 9 2 2 = + + + + + = + + + + + = - - - - p p the antenna efficiency is ) 4 . 14 ( 03596 . 0 81222 . 7 42008 . 0 30710 . 0 30710 . 0 db r r r r esr l r r - = + + = + + = h 2. the communication range r is m p s r rf 884 10 10 03596 . 0 10 05012 . 0 4 6913 . 0 4 3 2 12 2 = = = - - p h p l
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 10 of 16 february 2000 3. loop antenna measurements four different tuned loop antennas have been tested in an antenna laboratory. the loop antennas are made on a standard 1.6mm fr4 printed circuit board. the tested loop antenna sizes are: 1. 50x30mm 2. 35x20mm 3. 25x15mm 4. 18x10mm each antenna is tuned to a resonance frequency of 433,936mhz with a fixed chip capacitor (5%) in series with a variable capacitor. all loop antennas are tuned to approximately 400 w with a t-match. the resistor r q for controlling the q -value is not used in these measurements. the chip capacitor in series with the variable capacitor determines the maximum possible q -value of the loop antennas. the measured antennas has q-values of q = 5010%. to be able to compare the measurement results of the loop antennas to some known antenna response, measurements where made on a l /4 dipole antenna mounted on a 40x40cm ground plane. we have used a standard log periodic antenna in the antenna laboratory as the transmitter (tx) antenna for all measurements. the l /4 dipole antenna and the loop antennas under test have been used as receiver (rx) antennas. by doing the measurements this way, we measure the difference between the antennas, not the actual gain for each antenna. 3.1. antenna transmission for all measurements, the log periodic dipole is used as the transmitter antenna. the measurement presents s21 for the complete transmission. both the tx and rx antennas are part of the transmission budget. due to this we can not extract the absolute gain of the measured l /4 dipole and loop antennas. figure 3 shows the measured s21 for all the loop antennas and the l /4 dipole antenna. s21 a = s21 for l /4 dipole reference antenna s21 b = s21 for 50x30mm loop antenna s21 c = s21 for 35x20mm loop antenna s21 d = s21 for 25x15mm loop antenna s21 e = s21 for 18x10mm loop antenna
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 11 of 16 february 2000 figure 3 . plot of s21 for all loop antennas and l /4 dipole reference antenna each antenna measurement is discussed in the following chapters. 3.1.1. l l /4 dipole reference antenna the l /4 dipole antenna is a whip made of copper and has a length of 16.1cm. the antenna was mounted on a 40x40cm ground plane. from figure 3 we see that the l /4 dipole antenna has a measured value of ?46.5db at 434mhz. 3.1.2. 50x30mm loop antenna this antenna is tuned to 400 w , and has a quality factor of q = 48. figure 3 shows a measured peak value of ?52,5db at 434mhz for this antenna. compared to the l /4 dipole antenna, the 50x30mm loop antenna has 6db lower gain. 3.1.3. 35x20mm loop antenna this antenna is tuned to 386 w , and has a quality factor of q = 54. figure 3 shows a measured peak value of ?57.5db at 434mhz for this antenna. compared to the 50x30mm loop antenna, the 35x20mm loop antenna has 5db lower gain. the calculated difference in efficiency is 4.1db. gerber files for layout is available, see [3, 4, 5].
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 12 of 16 february 2000 3.1.4. 25x15mm loop antenna this antenna is tuned to 414 w , and has a quality factor of q = 48. figure 3 shows a measured peak value of ?61.5db at 434mhz for this antenna. compared to the 50x30mm loop antenna, the 25x15mm loop antenna has 9db lower gain. the calculated difference in efficiency is 8.4db. gerber files for layout is available, see [3, 4, 5]. 3.1.5. 18x10mm loop antenna this antenna is tuned to 400 w , and has a quality factor of q = 48. figure 3 shows a measured peak value of ?65.5db at 434mhz for this antenna. compared to the 50x30mm loop antenna, the 18x10mm loop antenna has 13db lower gain. the calculated difference in efficiency is 12.8db. gerber files for layout is available, see [3, 4, 5].
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 13 of 16 february 2000 4. references 1. c. a. balanis, ? antenna theory, analysis and design ?, second edition, john wiley & sons, inc., 1997. 2. j. d. kraus, ? electromagnetics ?, 4 th ed., mcgraw-hill book co., new york, 1992. 3. application note nan400-04 , ?nrf0433 rf and antenna layout?, nordic vlsi asa. 4. application note nan400-05 , ?nrf401 rf and antenna layout?, nordic vlsi asa. 5. application note nan400-06 , ?nrf402 rf and antenna layout?, nordic vlsi asa.
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 14 of 16 february 2000 liability disclaimer nordic vlsi asa reserves the right to make changes without further notice to the product to improve reliability, function or design. nordic vlsi does not assume any liability arising out of the application or use of any product or circuits described herein. life support applications these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. nordic vlsi asa customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify nordic vlsi asa for any damages resulting from such improper use or sale. application note. revision date : 29.02.2000. application note order code : 290200-nan400-03 all rights reserved ?. reproduction in whole or in part is prohibited without the prior written permission of the copyright holder.
application note small loop antennas nordic vlsi asa - vestre rosten 81, n-7075 tiller, norway - phone +47 72 89 89 00 - fax +47 72 89 89 89 revision: 1.2 page 15 of 16 february 2000 your notes
application note small loop antennas revision: 1.2 page 16 of 16 february 2000 nordic vlsi - world wide distributors for your nearest dealer, please see http://www.nvlsi.no main office: vestre rosten 81, n-7075 tiller, norway phone: +47 72 89 89 00, fax: +47 72 89 89 89 e-mail: nrf@nvlsi.no visit the nordic vlsi asa website at http://www.nvlsi.no

▲Up To Search▲

Price & Availability of ALL4XXAND9XX

	To Download ALL4XXAND9XX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .