everlight electronics co.,ltd. everlight electronics co., ltd. http://www.everlight.com rev 1 page: 1 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i technical data sheet 1206 package chip led (1.1 mm height) 15-21/g6c-fp1q1l/2t features ? package in 8m m tape on 7 diam eter reel. ? com p atible with autom a tic placem ent equipm ent. ? com p atible with infrared and vapor phase reflow solder process. ? mono-color type. ? pb-free. descriptions ? the 15-21 smd taping is m u ch sm aller than lead fram e type com ponents, thus enable sm aller board size, higher packing density, reduced storage space and finally sm aller equipm ent to be obtained. ? besides, lightweight m a kes them ideal for m i niature applications. etc. applications ? autom o tive: backlighting in dashboard and switch. ? telecom m unication: indicator and backlighting in telephone and fax. ? flat backlight for lcd, switch and sym bol. ? general use. device selection guide chip part no. m a t e r i a l e m i t t e d c o l o r lens color 15-21/g6c-fp1q1l/2t algainp brilliant yellow green w a ter clear
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 2 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i pack age outline dimensions note: tolerances unless dim e nsion 0 . 1 mm , un it = mm
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 3 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i absolute maximum ratings (ta=25 ) param e t e r s y m b o l r a t i n g u n i t reverse voltage v r 5 v forward current i f 2 5 m a operating tem p erature topr -40 ~ +85 storage tem p erature tstg -40 ~ +90 electrostatic discharge esd 2000 v power dissipation pd 60 m w peak forward current (duty 1/10 @1khz) i fp 6 0 m a soldering tem p erature tsol reflow soldering : 260 for 10sec. hand soldering : 350 for 3 sec. electro-optical characteristics (ta=25 ) param e t e r s y m bol m i n . t y p . m a x . unit condition lum i nous intensity iv 45.0 ----- 90.0 m c d viewing angle 2 1 / 2 - - - - - 1 4 0 - - - - - d e g peak w a velength p - - - - - 5 7 5 - - - - - nm dom i nant w a velength d 5 7 0 . 0 - - - - - 5 7 4 . 5 nm spectrum radiation bandwidth - - - - - 2 0 - - - - - nm forward voltage v f 1 . 7 0 - - - - - 2 . 3 0 v i f =20m a reverse current i r - - - - - - - - - - 1 0 a v r =5v notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forw ard voltage 0.05v
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 4 of 10 device no:szdse-151-g06 prepared date:23-mar-2005 prepared by: zhang huali bin range of dom. wavelength group bin min max unit condition cc2 570.0 571.5 cc3 571.5 573.0 f cc4 573.0 574.5 nm i f =20ma bin range of luminous intensity bin min max unit condition p1 45.0 57.0 p2 57.0 72.0 q1 72.0 90.0 mcd i f =20ma bin range of forward voltage group bin min max unit condition 19 1.70 1.80 20 1.80 1.90 21 1.90 2.00 22 2.00 2.10 23 2.10 2.20 l 24 2.20 2.30 v i f =20ma notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forward voltage 0.05v
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 5 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i typical electro-optical characteristics curves
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 6 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i label explanation cat: luminous intensity rank hue: dom. wavelength rank ref: forw ard voltage rank reel dimensions note: tolerances unless dim e nsion 0 . 1 mm , un it = mm
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 7 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i carrier tape dimensions: loaded quantity 2000 pcs per reel note: tolerances unless dim e nsion 0 . 1 mm , un it = mm moisture resistant pack aging label aluminum moisture-proof bag desiccant l abel
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 8 of 10 device no:szdse-151-g06 prepared date:23-mar-2005 prepared by: zhang huali reliability test items and conditions the reliability of products shall be satisfied with items listed below. confidence level90% ltpd 10% no. items test condition test hours/cycles sample size ac/re 1 reflow soldering temp. : 260 5 min 5 sec. 6 min. 22 pcs. 0/1 2 temperature cycle h : +100 15min 5 min l : -40 15min 300 cycles 22 pcs. 0/1 3 thermal shock h : +100 5min 10 sec l : -10 5min 300 cycles 22 pcs. 0/1 4 high temperature storage temp. : 100 1000 hrs. 22 pcs. 0/1 5 low temperature storage temp. : -40 1000 hrs. 22 pcs. 0/1 6 dc operating life i f = 20 ma 1000 hrs. 22 pcs. 0/1 7 high temperature / high humidity 85 /85% rh 1000 hrs. 22 pcs. 0/1
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 9 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i precautions for use 1. over-current-proof custom er m u st apply resistors f o r protection , otherwise slight voltage shif t will cause big current change ( burn out will happen ). 2. storage 2.1 do not open m o isture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3after opening the package, the leds should be kept at 30 or less and 70%rh or less(floor life). however,it? s recom m e nded that the leds should be used within 168 hours (7 days) after opening the package.if unused led rem a in, it should be stored in m o isture proof packages. 2.4 if the m o isture absorbent m a terial (silica gel) has faded away or the leds have exceeded the storage tim e, baking treatm e nt should be perform e d using the following conditions. baking treatm e nt : 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder tem p erature profile 3.2 reflow soldering should not be done m o re than two tim es. 3.3 w h en soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board. 4.soldering iron each term inal is to go to the tip of soldering iron tem p erature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w . leave two seconds and m o re intervals, and do soldering of each term inal. be careful because the da m a ge of the product is often started at the tim e of the hand solder.
everlight electronics co.,ltd. 15-21/g6c-fp1q1l/2t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 10 of 10 devi ce no: s zdse-151-g06 prepared dat e : 23-m a r-2005 prepared by : zhang hual i 5.repairing repair should not be done after the leds have been soldered. w h en repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirm e d beforehand whether the characteristics of the leds will or will not be dam a ged by repairing. e verlight electronics co., ltd. tel : 0512-63409123-1603 of f i ce: n o 355,zhong shan n o rt h rd ,wuji ang, fax: 0512-63409123-1510 economy development zone(yunx i area) , http://www.everlight.com songling town, w ujiang city, j iangsu p r c , china.
|
