original creation date: 11/29/94 last update date: 10/14/98 last major revision date: 03/19/97 mn54abt574-x rev 0b0 microcircuit data sheet octal d-type flip-flop with 3-state outputs general description the abt574 is a high-speed, low power octal d-type flip-flop with a buffered common clock(cp) and a buffered common output enable(oe). the information presented to the d inputs is stored in the flip-flops on the low-to-high clock(cp) transistion. the device is functionally identical to the 54abt374 except for the pinouts. ns part numbers 54abt574e-qml * 54ABT574J-QML ** 54abt574w-qml *** industry part number 54abt574 prime die nb574 controlling document see features page processing mil-std-883, method 5004 quality conformance inspection mil-std-883, method 5005 subgrp description temp ( c) o 1 static tests at +25 2 static tests at +125 3 static tests at -55 4 dynamic tests at +25 5 dynamic tests at +125 6 dynamic tests at -55 7 functional tests at +25 8a functional tests at +125 8b functional tests at -55 9 switching tests at +25 10 switching tests at +125 11 switching tests at -55 1
microcircuit data sheet mn54abt574-x rev 0b0 features - inputs and outputs on opposite sides of package allowing easy interface with microprocessors - useful as input or output port for microprocessors - tri-state outputs for bus-oriented applications - output sink capability of 48ma, source capability of 24 ma - guaranteed latchup protection - high impedance glitch free bus loading during entire power up and power down cycle. - non-destructive hot insertion capability. - smd : 5962-9322001q2a*, qra**, qsa*** 2
microcircuit data sheet mn54abt574-x rev 0b0 (absolute maximum ratings) (note 1) vcc pin potential to ground potential -0.5v to +7.0v input voltage (note 2) -0.5v to +7.0v input current (note 2) -30ma to +5.0ma voltage applied to any output -0.5v to 5.5v in the disabled or power-off state -0.5v to vcc in the high state current applied to output 96ma in the low state (max) junction temperature (tj) +175c ceramic thermal resistance see mil-std 1835 junction-to-case (theta jc) storage temperature -65c to +150c lead temperature +300c (soldering, 10 seconds) esd classification class 3 maximum power dissipation 500 mw note 1: absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. functional operation under these conditions is not implied. note 2: either voltage limit or current limit is sufficient to protect inputs. recommended operating conditions supply voltage (vcc) 4.5v to 5.5v operating temperature -55c to +125c minimum input edge rate (dv/dt) 50 mv/ns data input 20 mv/ns enable input 100mv/ns clock input maximum output current -24 ma high level (ioh) 48 ma low level (iol) 3
mn54abt574-x rev 0b0 microcircuit data sheet electrical characteristics dc parameters (the following conditions apply to all the following parameters, unless otherwise specified.) dc: 4.5v to 5.5v temp range: -55c to 125c symbol parameter conditions notes pin- name min max unit sub- groups icch supply current vcc=5.5v, vinh=5.5v, vinl=0.0v 1, 4 vcc 250.0 ua 1, 2, 3 iccl supply current vcc=5.5v, vinh=5.5v, vinl=0.0v 1, 4 vcc 30.0 ma 1, 2, 3 iccz supply current vcc=5.5v, vinh=5.5v, vinl=0.0v 1, 4 vcc 250.0 ua 1, 2, 3 icct supply current per input vcc=5.5v, oe=0.0v input under test=3.4v other inputs=5.5v or 0.0v 1, 4 vcc 2.5 ma 1, 2, 3 vcc=5.5v, oe=3.4v other inputs=5.5v or 0.0v 1, 4 vcc 2.5 ma 1, 2, 3 iih high level input current vcc=5.5v, vinh=5.5v 1, 4 in 2.0 ua 1, 2, 3 iil low level input current vcc=5.5v, vinl=0.0v 1, 4 in -2.0 ua 1, 2, 3 iozh maximum tri-state leakage current high vcc=5.5v, vout=2.7v vinl=0.0v, vih (oe)=2.0v 1, 4 out 10.0 ua 1, 2, 3 iozl maximum tri-state leakage current low vcc=5.5v, vout=0.5v vinh=5.5v, vih (oe)=2.0v 1, 4 out -10.0 ua 1, 2, 3 icex output high leakage current vcc=5.5v, vout=5.5v vinh=5.5v 1, 4 out 50.0 ua 1, 2, 3 ios output short circuit current vcc=5.5v, vout=0.0v vinh=5.5v 1, 4, 10 out -100 -275 ma 1, 2, 3 ios1 output short circuit current vcc=5.5v, vout=2.5v vinh=5.5v 1, 4, 10 out -50 -180 ma 1, 2, 3 ibvi input high current breakdown test vcc=5.5v, vinh=7.0v 1, 4 in 7.0 ua 1, 2, 3 izz bus drainage test vcc=0.0v, vout=4.5v, vinl=0.0v 1, 4 in/out -100 100 ua 1, 2, 3 vol low level output voltage vcc=4.5v, iol=48.0ma, vinh=4.5v, vinl=0.0v, vih=2.0v, vil=0.8v 1, 4 out 0.55 v 1, 2, 3 voh high level output voltage vcc=4.5v, ioh=-24.0ma, vinh=4.5v, vinl=0.0v, vih=2.0v, vil=0.8v 1, 4 out 2.0 v 1, 2, 3 vcc=4.5v, ioh=-3ma, vinh=4.5v, vinl=0.0v, vih=2.0v, vil=0.8v 1, 4 out 2.5 v 1, 2, 3 vcc=5.0v, ioh=-3ma, vinh=5.0v, vinl=0.0v, vih=2.0v, vil=0.8v 1, 4 out 3.0 v 1, 2, 3 4
mn54abt574-x rev 0b0 microcircuit data sheet electrical characteristics dc parameters(continued) (the following conditions apply to all the following parameters, unless otherwise specified.) dc: 4.5v to 5.5v temp range: -55c to 125c symbol parameter conditions notes pin- name min max unit sub- groups vid input leakage test vcc=0.0v, iid=1.9ua, vinl=0.0v 1, 4 in 4.75 v 1, 2, 3 vcd input clamp diode voltage vcc=4.5v, ikl=-18ma, vinh=4.5v, vinl=0.0v 1, 4 in -1.2 v 1, 2, 3 volp low level ground bounce vcc=5.0v, load : 50pf / 500 ohms 7, 8 out 0.8 v 4 volv low level ground bounce vcc=5.0v, load : 50pf / 500 ohms 7, 8 out -1.7 v 4 vohp high level vcc bounce vcc=5.0v, load : 50pf / 500 ohms 7, 8 out 1.3 v 4 vohv high level vcc bounce vcc=5.0v, load : 50pf / 500 ohms 7, 8 out -0.8 v 4 cin input capacitance vcc=0.0v 7 in 8.5 pf 4 cout output capacitance vcc=5.0v 7 out 14.5 pf 4 5
mn54abt574-x rev 0b0 microcircuit data sheet electrical characteristics ac parameters (the following conditions apply to all the following parameters, unless otherwise specified.) ac: cl=50pf rl=500 ohms trise/tfall = 3.0ns symbol parameter conditions notes pin- name min max unit sub- groups tplh propagation delay vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 cp to on 1.5 6.2 ns 9 2, 5 cp to on 1.5 7.0 ns 10, 11 tphl propagation delay vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 cp to on 1.5 7.0 ns 9 2, 5 cp to on 1.5 7.4 ns 10, 11 tpzl output enable time vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 oe to on 1.0 5.9 ns 9 2, 5 oe to on 1.0 7.2 ns 10, 11 tpzh output enable time vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 oe to on 1.0 5.5 ns 9 2, 5 oe to on 1.0 6.5 ns 10, 11 tphz output disable time vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 oe to on 1.0 6.2 ns 9 2, 5 oe to on 1.0 7.2 ns 10, 11 tplz output disable time vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 2, 5 oe to on 1.0 5.8 ns 9 2, 5 oe to on 1.0 6.7 ns 10, 11 ts(h) setup time (high) vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 7 dn - cp 1.5 ns 9, 10, 11 ts(l) setup time (low) vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 7 dn - cp 2.0 ns 9, 10, 11 th(h/l) hold time high or low vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 7 dn - cp 2.0 ns 9, 10, 11 tw(h/l) pulse width vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 7 cp 3.3 ns 9, 10, 11 fmax maximum clock frequency vcc=5.0v @25c, vcc=4.5v & 5.5v @-55c/125c 7 cp 150 mhz 9, 10, 11 note 1: screen tested 100% on each device at -55c, +25c & +125c temp., subgroups 1,2,3,7 & 8. note 2: screen tested 100% on each device at -55c, +25c & +125c temp., subgroups a9, a10 & a11. note 3: screen tested 100% on each device at +25c temp.only, subgroup 9. note 4: sample tested (method 5005, table 1) on each mfg. lot at +25c, +125c & -55c temp., subgroups a1, 2, 3, 7 & 8. note 5: sample tested (method 5005, table 1) on each mfg. lot at +25c, +125c & -55c temp., subgroups a9, 10, 11. 6
mn54abt574-x rev 0b0 microcircuit data sheet (continued) note 6: sample tested (method 5005, table 1) on each mfg. lot at +25c temp. only, subgroup a9. note 7: not tested (guaranteed by design characterization data). note 8: max number of outputs defined as (n). n-1 data inputs are driven 0v to 3.0v. one output at @ vol or @ voh. note 9: max number of data inputs (n) switching. (n-1) inputs switching ov t0 3.0v. input-undertest switching: 3v to threshold (vild), 0v to threshold (vihd), freq.= 1 mhz. note 10: maximum test duration not to exceed one second, not more than one output shorted at one time. 7
microcircuit data sheet mn54abt574-x rev 0b0 graphics and diagrams graphics# description e20are lcc (e), type c, 20 terminal(p/p dwg) j20arm cerdip (j), 20 lead (p/p dwg) p000025a (new) p000026a (new) w20arf cerpack (w), 20 lead (p/p dwg) see attached graphics following this page. 8
microcircuit data sheet mn54abt574-x rev 0b0 revision history rev ecn # rel date originator changes 0b0 m0001581 10/14/98 bill petcher changed mds mn54abt574-x rev 0a0 to mn54abt574-x rev 0b0 9
|
