description features 5v/3.3v 1:2 differential fanout buffer pin names pin configuration/block diagram pin function d data inputs q 0 , q 1 data outputs 1 2 3 4 5 6 7 8 q 0 q 1 v cc d v ee d q 0 q 1 soic top view precision edge sy10el11v sy100el11v final 3.3v and 5v power supply options 265ps propagation delay 5ps skew between outputs high bandwidth output transitions internal 75k ? input pull-down resistors replaces sy10/100el11 improved output waveform characteristics available in 8-pin soic package the sy10/100el11v are 1:2 differential fanout gates. these devices are functionally similar to the e111a/l devices, with higher performance capabilities. having within-device skews and output transition times significantly improved over the e111a/l, the el11v is ideally suited for those applications which require the ultimate in ac performance. the differential inputs of the el11v employ clamping circuitry to maintain stability under open input conditions. if the inputs are left open (pulled to v ee ), the q outputs will go low. 1 rev.: e amendment: /0 issue date: february 2003 precision edge precision edge is a trademark of micrel, inc.
2 sy10el11v sy100el11v micrel symbol rating value unit v cc power supply voltage (v ee = 0) +6.0 to 0 v v ee power supply voltage (v cc = 0) ?.0 to 0 v v in input voltage (v cc = 0v, v in not more negative than v ee ) ?.0 to 0 v input voltage (v ee = 0v, v in not more positive than v cc ) +6.0 to 0 v i out output current ?ontinuous 50 ma ?urge 100 t a operating temperature range ?0 to +85 c t store storage temperature range ?5 to +150 c ja thermal resistance (junction-to-ambient) ?till air 160 c/w ?00lfpm 109 c/w jc thermal resistance (junction-to-case) 39 c/w absolute maximum ratings (1) note: 1. permanent device damage may occur if absolute maximum ratings are exceeded. this is a stress rating only and functional oper ation is not implied at conditions other than those detailed in the operational sections of this data sheet. exposure to absolute maximum ratlng co nditions for extended periods may affect device reliability. t a = ?0 ct a = 0 ct a = +25 ct a = +85 c symbol parameter min. typ. max. min. typ. max. min. typ. max. min. typ. max. unit i ee power supply current ma 10el 26 31 15 26 31 15 26 31 15 26 31 100el 26 31 15 26 31 15 26 31 15 30 36 i ih input high current 150 150 150 150 a dc electrical characteristics (1) v ee = v ee (min.) to v ee (max.); v cc = gnd note: 1. parametric values specified at: 10/100el11v series: -3.0v to -5.5v.
3 sy10el11v sy100el11v micrel t a = ?0 ct a = 0 ct a = +25 ct a = +85 c symbol parameter min. typ. max. min. typ. max. min. typ. max. min. typ. max. unit t plh propagation delay to 135 260 385 185 260 335 190 265 340 215 290 365 ps t phl output d t skew within-device skew (2) 5 520 520 520ps duty cycle skew (3) 5 520 520 520 v pp minimum input swing (4) 150 150 150 150 mv v cmr common mode range (5) ?.3 ?.4 ?.4 ?.4 ?.4 ?.4 ?.4 ?.4 v t r output rise/fall times q 100 225 350 100 225 350 100 225 350 100 225 350 ps t f (20% to 80%) ac electrical characteristics (1) v ee = v ee (min.) to v ee (max.); v cc = gnd notes: 1. parametric values specified at: 10/100el11v series: -3.0v to -5.5v. 2. within-device skew defined as identical transitions on similar paths through a device. 3. duty cycle skew is the difference between a t plh and t phl propagation delay through a device. 4. minimum input swing for which ac parameters are guaranteed. the device has a dc gain of 40. 5. the cmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls within the specified range and the peak-to-peak voltage lies between v pp min. and 1v. the lower end of the cmr range varies 1:1 with v ee . the numbers in the spec table assume a nominal v ee = ?.3v. note for pecl operation, the v cmr (min) will be fixed at 3.3v ?|v cmr (min)|. product ordering code ordering package operating package code type range marking sy10el11vzc z8-1 commercial hel11v sy10el11vzctr* z8-1 commercial hel11v sy100el11vzc z8-1 commercial xel11v sy100el11vzctr* z8-1 commercial xel11v * tape and reel note 1. recommended for new designs. ordering package operating package code type range marking sy10el11vzi (1) z8-1 industrial hel11v sy10el11vzitr* (1) z8-1 industrial hel11v sy100el11vzi (1) z8-1 industrial xel11v sy100el11vzitr* (1) z8-1 industrial xel11v * tape and reel
4 sy10el11v sy100el11v micrel 8 lead soic .150" wide (z8-1) rev. 03 micrel, inc. 1849 fortune drive san jose, ca 95131 usa tel + 1 (408) 944-0800 fax + 1 (408) 944-0970 web http://www.micrel.com the information furnished by micrel in this datasheet is believed to be accurate and reliable. however, no responsibility is as sumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intend ed for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant inj ury to the user. a purchaser s use or sale of micrel products for use in life support appliances, devices or systems is at purchaser s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2003 micrel, incorporated.
|
