is1a thru is1m sur f ace mount general rectifier reverse v oltage - 50 to 1000 v olts forward current - 1.0 ampere maximum ratings and electrical characteristics is1a volts volts volts symbols units amp amps volts v rrm v rms v dc i (av) i fsm v f 1.0 30.0 1.1 operating junction and storage temperature range maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t l =110 c peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 1.0a maximum dc reverse current t a =25 c at rated dc blocking voltage t a =100 c typical junction capacitance (note 1) note: 1.measured at 1mhz and applied reverse voltage of 4.0v d.c. 2. p .c.b. mounted with 0.2 x 0.2 ? (5.0 x 5.0mm) copper pad areas i r 5.0 50.0 r q ja c j t j , t stg 75.0 15.0 -65 to +175 pf c a m typical thermal resistance (note 2) c/w ratings at 25 c ambient temperature unless otherwise specified. single phase half-wave 60hz, resistive or inductive load, for capacitive load current derate by 20%. dimensions in inches and (millimeters) is1b is1d is1g is1j IS1K is1m case : jedec do-214aa molded plastic body terminals : solder plated, solderable per mil-std-750, method 2026 polarity : color band denotes cathode end mounting position : any w eight : 0.005 ounce, 0.138 grams the plastic package carries underwriters laboratory flammability classification 94v-0 for surface mounted applications low reverse leakage built-in strain relief, ideal for automated placement high forward surge current capability high temperature soldering guaranteed: 250 c/10 seconds at terminals features mechanical data nvac 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 0.086 (2.20) 0.077 (1.95) 0.180(4.57) 0.160(4.06) 0.155(3.94) 0.130(3.30) 0.122(3.12) 0.110(2.82) 0.060(1.52) 0.030(0.76) 0.220(5.59) 0.205(5.21) 0.012(0.305) 0.006(0.152) 0.008(0.203)max. do-214aa
ratings and characteristic curves is1a thru is1m nvac 1.0 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 175 30 25 20 15 10 5.0 0.6 0.8 1.0 1.2 1.4 1.5 0.1 1.0 10 100 0.01 0.1 1 10 100 100 10 1 0.1 reverse vo l t age, vo l ts t, pulse dur a tion, sec. fig. 5-typical junction capacitance fig. 6-typical transient thermal impedance fig. 3-typical instantaneous forward characteristics number of cycles at 60 hz fig. 2-maximum non-repetitive peak forward surge current fig. 1- forward current derating curve average forward rectified current, amperes instantaneous forward current,amperes junction capacitance, pf peak forward surge current, amperes ins t an t aneous fo r w ard vol t age, volts single phase half wave 60hz resistive or inductive load 1 10 100 8.3ms single half sine-wave (jedec method) 0.01 0.1 1 20 10 t j =25 c pulse width=300 m s 1%duty cycle t j =25 c 1 10 100 200 0 20 40 60 80 100 1,000 100 10 1 0.1 0.01 tj=100 c tj=25 c tj=150 c percent of peak reverse vo l t age, % fig. 4-typical reverse characteristics instantaneous reverse current, microamperes transient thermal impedance, c/w ambient temperature, c
|
