the information in this document is subject to change without notice. before using this document, please confirm that this is the latest version. not all devices/types available in every country. please check with local nec representative for availability and additional information. ? 2000 bipolar analog integrated circuit m m m m pc1060 2.5 v high precision reference voltage circuit data sheet document no. g14607ej4v0ds00 (4th edition) (previous no. ic-1537) date published march 2000 ns cp (k) printed in japan the mark shows major revised points. description the m pc1060 are high accuracy and low drift voltage references of 2.5 v output voltage. this ic can operate under wide range input voltage, and applied for 8 to 12 bits d/a converters. features pin configuration ? high accuracy ? low temperature coefficient ? low supply current ? wide supply voltage range ? low load regulation v o = 2.5 v 1 % d v o / d t 40 ppm/ c i cc 1.5 ma 4.5 v v in 40 v reg l 10 mv 1 input output gnd nc nc nc nc nc pC1060C m 8-pin plastic dip (7.62 mm (300)) 2 3 4 8 7 6 5 ordering information part number package m pC1060C 8-pin plastic dip (7.62 mm (300)) equivalent circuit input output r 5 q 16 q 13 q 6 q 11 q 1 q 9 q 2 q 8 q 12 q 4 q 7 q 14 q 3 q 10 q 15 r 11 c 1 r 1 r 18 r 17 r 16 r 15 r 14 r 2 r 4 r 6 r 12 r 13 r 7 r 8 r 9 gnd
data sheet g14607ej4v0ds00 2 m m m m pc1060 absolute maximum ratings (t a = +25 c, unless otherwise specified.) parameter symbol ratings unit input voltage v in - 0.3 to +40 v total power dissipation p t 350 mw operating ambient temperature t a - 20 to +70 c storage temperature t stg - 55 to +125 c caution product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. that is the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. typical connection 1 gnd output output input input c o c in 3 2 m 0.1 f m 0.1 f recommended operating conditions parameter symbol min. typ. max. unit input voltage v in 4.5 40 v output current i o 010ma internal power dissipation p d 270 mw operating ambient temperature t a - 20 +70 c caution the recommended operating range may be exceeded without causing any problems provided that the absolute maximum ratings are not exceeded. however, if the device is operated in a way that exceeds the recommended operating conditions, the margin between the actual conditions of use and the absolute maximum ratings is small, and therefore thorough evaluation is necessary. the recommended operating conditions do not imply that the device can be used with all values at their maximum values.
data sheet g14607ej4v0ds00 3 m m m m pc1060 electrical characteristics (v in = 15 v, i o = 0 a, t a = +25 c, unless otherwise specified.) parameter symbol test conditions min. typ. max. unit output voltage v o 2.475 2.5 2.525 v output voltage change d v o 0 c t a 70 c7.0mv temperature coefficient of output voltage d v o / d t0 c t a 70 c 40 ppm/ c line regulation reg in 15 v v in 40 v 4.5 mv 4.5 v v in 15 v 3.0 mv load regulation reg l 0 a i o 10 ma 10 mv ripple rejection r?r 5 v v in 40 v, f = 120 hz 90 db output noise voltage v n 4.5 v v in 40 v, 0 a i o 10 ma, p t 350 mw 80 m v p-p short circuit current i oshort v o = 0 v 17 ma circuit current i cc 1.5 ma
data sheet g14607ej4v0ds00 4 m m m m pc1060 typical characteristic (t a = +25 c, unless otherwise specified. nominal) - 20 0 20 - 5 0 - 5 0 40 60 80 t a - operating ambient temperature - c v o vs t a v o - output voltage cange - mv v in = 15 v, i o = 0 a 0 26810 4 i o - output current - ma t a = + 25 c t a = 0 c t a = - 20 c t a = + 70 c t a = + 50 c d d v in = 15 v - 5 0 0 10 30 40 20 v in - input voltage - v t a = 0 c t a = - 20 c t a = + 25 c t a = + 70 c t a = + 50 c i o = 0 a v o vs i o d v o vs v in d 0 10 30 40 20 v in - input voltage - v t a = + 25 c t a = - 20 c t a = + 70 c i o = 0 a i cc vs v in - 20 0 20 1.20 1.15 1.10 1.05 1.00 0 1.20 1.15 1.10 1.05 40 60 80 t a - operating ambient temperature - c i cc vs t a i cc - circuit current - ma i cc - circuit current - ma v in = 15 v, i o = 0 a 0 0.1 0.2 0.3 0.4 0.5 25 75 100 125 50 t a - operating ambient temperature - c p t vs t a p t - total power dissipation - w 200 c/w v o - output voltage cange - mv d v o - output voltage cange - mv d
data sheet g14607ej4v0ds00 5 m m m m pc1060 package drawing 14 85 item millimeters notes 1. each lead centerline is located within 0.25 mm of its true position (t.p.) at maximum material condition. p8c-100-300b,c-2 n 0.25 p 0.9 min. r0 ~ 15 a 10.16 max. b 1.27 max. f 1.4 min. g 3.2 0.3 j 5.08 max. k 7.62 (t.p.) c 2.54 (t.p.) d 0.50 0.10 h 0.51 min. i 4.31 max. l 6.4 m 0.25 + 0.10 - 0.05 2. ltem "k" to center of leads when formed parallel. m a r m p i j h g f dn c b 8-pin plastic dip (7.62mm(300)) l k
data sheet g14607ej4v0ds00 6 m m m m pc1060 recommended soldering conditions when soldering this product, it is highly recommended to observe the conditions as shown below. if other soldering processes are used, or if the soldering is performed under different conditions, please make sure to consult with our sales offices. for more details, refer to our document semiconductor device mounting technology manual (c10535e) . type of through-hole device m m m m pC1060C : 8-pin plastic dip (7.62 mm (300)) process conditions wave soldering (only to leads) solder temperature: 260 c or below, flow time: 10 seconds or less. caution for through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. reference documents semiconductor device mounting technology manual c10535e semiconductor selection guide -products and packages- x13769x
data sheet g14607ej4v0ds00 7 m m m m pc1060 [memo]
m m m m pc1060 [memo] the information in this document is subject to change without notice. before using this document, please confirm that this is the latest version. no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec corporation. nec corporation assumes no responsibility for any errors which may appear in this document. nec corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. no license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec corporation or others. descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. nec corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. while nec corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. to minimize risks of damage or injury to persons or property arising from a defect in an nec semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. nec devices are classified into the following three quality grades: "standard", "special", and "specific". the specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. the recommended applications of a device depend on its quality grade, as indicated below. customers must check the quality grade of each device before using it in a particular application. standard: computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots special: transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) specific: aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. the quality grade of nec devices is "standard" unless otherwise specified in nec's data sheets or data books. if customers intend to use nec devices for applications other than those specified for standard quality grade, they should contact an nec sales representative in advance. m7 98. 8
|
