ps9117 nec's high cmr, 10mbps open collector output type 5-pin sop optocoupler california eastern laboratories ? pulse width dist ort ion : |t phl - t plh | = 35 ns max. ? high common mode transient immunity: cm h , cm l = 15 kv/ s min. ? small package: 5-pin sop ? high speed: 10 mbps ? high isolation voltage: bv = 2 500 v r.m.s. ? open collector output ? ordering number of taping product: ps9117-f3, f4: 2 500 pcs/reel ? pb-free product ? safety standards: ul approved: file no. e72422 din en60747-5-2 (vde0884 part2) approved no. 40008902 (option) features data sheet nec's ps9117 is an optically coupled high-speed, active low type isolator containing a gaalas led on the input side and a photodiode and a signal process - ing circuit on the output side on one chip. the ps9117 is designed speci?cally for high common mode transient immunity (cmr) and low pulse width distortion. the ps9117 is suitable for high density ap - plication. description ? measurement equipment ? pdp ? fa network application 5 3 1 2 4 1. anode 2. cathode 3. gnd 4. v o 5. v cc pin connection (t op v iew) truth table led output on l off h
ps9117 package dimensions (unit: mm) 1.27 0.4 +0.10 -0.0 5 0.25 m 0.10.1 2.60.2 4.4 7.00.3 0.50.3 0.15 +0.10 -0.0 5 3.4 +0. 3 -0.1 5 3 1 2 4 marking example no. 1 pin mark initial of nec (engraved mark) rank code ye ar assembled (last 1 digit) w eek assembled n 2 34 assembly lot 91 17 n234 n *1 *1 bar : pb-free
ps9117 ordering information *1 for the application of the safety standard, following part number should be used. *2 with regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales of?ce. part number order number solder plating specification packing style safety standards approval application part number *1 ps9117 ps9117-a pb-free *2 magazine case 100 pcs ul approved ps9117 ps9117-f3 PS9117-F3-A embossed tape 2 500 pcs/reel ps9117-f4 ps9117-f4-a ps9117-v ps9117-v-a magazine case 100 pcs din en60747-5-2 (vde0884 part2) approved (option) ps9117-v-f3 ps9117-v-f3-a embossed tape 2 500 pcs/reel ps9117-v-f4 ps9117-v-f4-a absolute maximum ratings ( t a = 25oc, unless otherwise speci?ed ) parameter symbol ratings unit diode forward current *1 i f 30 ma reverse voltage v r 5 v detector supply voltage v cc 7 v output voltage v o 7 v output current i o 25 ma power dissipation *2 p c 40 mw isolation voltage *3 bv 2 500 vr.m.s. operating ambient temperature t a ? 40 to +85 c storage temperature t stg ? 55 to +125 c *1 reduced to 0.3 ma/ c at t a = 25 c or more. *2 applies to output pin v o (collector pin). reduced to 1.5 mw/ c at t a = 65 c or more. *3 ac voltage for 1 minute at t a = 25 c, rh = 60% between input and output.
ps9117 recommended operating conditions parameter symbol min. typ. max. unit low level input voltage v fl 0 0.8 v high level input current i fh 6.3 10 12.5 ma supply voltage v cc 4.5 5.0 5.5 v ttl (r l = 1 k , loads) n 5 pull-up resistor r l 330 4 k electrical characteristics ( t a = -40 to 85 oc, un less otherwise speci?ed ) parameter symbol conditions min. typ. *1 max. unit diode forward voltage v f i f = 10 ma, t a = 25 c 1.4 1.65 1.8 v reverse current i r v r = 3 v, t a = 25 c 10 a terminal capacitance c t v = 0 v, f = 1 mhz, t a = 25 c 30 pf detector high level output current i oh v cc = v o = 5.5 v, v f = 0.8 v 1 100 a low level output voltage *2 v ol v cc = 5.5 v, i f = 5 ma, i ol = 13 ma 0.2 0.6 v high level supply current i cch v cc = 5.5 v, i f = 0 ma 5 8 ma low level supply current i ccl v cc = 5.5 v, i f = 10 ma 9 11 coupled threshold input current (h l) i fhl v cc = 5 v, v o = 0.8 v, r l = 350 2 5 isolation resistance r i-o v i-o = 1 kv dc , rh = 40 to 60%, t a = 25 c 10 11 isolation capacitance c i-o v = 0 v, f = 1 mhz, t a = 25 c 0.6 pf propagation delay time (h l) *3 t phl t a = 25 c 35 75 ns v cc = 5 v, r l = 350 , i f = 7.5 ma 100 propagation delay time (l h) *3 t plh t a = 25 c 40 75 v cc = 5 v, r l = 350 , i f = 7.5 ma 100 rise time t r v cc = 5 v, r l = 350 , i f = 7.5 ma 20 fall time t f 5 pulse width distortion (pwd) *3 |t phl- t plh | 5 35 propagation delay skew t psk 40 common mode transient immunity at high level output *4 cm h v cc = 5 v, r l = 350 , t a = 25 c, i f = 0 ma, v o > 2 v, v cm = 1 kv 15 20 kv/ s common mode transient immunity at low level output *4 cm l v cc = 5 v, r l = 350 , t a = 25 c, i f = 7.5 ma, v o < 0.8 v, v cm = 1 kv 15 20 kv/ s
ps9117 *1 typical values at t a = 25 c *2 because v ol of 2 v or more may be output when led current input and when output supply of v cc = 2.6 v or less, it is important to con?rm the characteristics (operation with the power supply on and of f) during design, before using this device. *3 test circuit for propagation delay time input output 1.5 v v ol t phl t plh (i f = 7.5 ma) 50% 47 ? pulse input (i f ) v o (monitor ) v cc = 5 v input (monitor ) 0.1 f c l = 15 pf r l = 350 ? (pw = 1 s, duty cycle = 1/10) remark c l includes probe and stray wiring capacitance. *4 test circuit for common mode transient immunity 90% 10% 1 kv 0 v v oh 2 v 0.8 v v ol v cm v o (i f = 0 ma) v o (i f = 7.5 ma) t r t f v o (monitor) v cc = 5 v 0.1 f c l = 15 pf sw v cm i f r l = 350 ? remark c l includes probe and stray wiring capacitance. usage cautions 1. this product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. by-pass capacitor of 0.1 f is used between v cc and gnd near device. also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm.
ps9117 remark the graphs indicate nominal characteristics. typical characteristics ( t a = 25oc, unless otherwise speci?ed ) 20 40 60 80 100 0 85 10 20 30 40 20 40 60 80 85 100 0 20 10 30 50 40 1.0 0.01 0.1 1 10 100 1.2 1.4 1.6 1.8 2.0 2.2 2.4 t a = +85oc +50oc +25oc 0oc -25oc -50 -25 0 25 50 7 5 100 0 12 10 8 6 4 2 i ccl (i f = 10 ma) i cch (i f = 0 ma) 1 2 3 4 5 6 -50 -25 0 25 50 7 5 100 i f = 5.0 ma, v cc = 5.5 v 6 5 4 3 2 1 0 0.6 0.5 0.4 0.3 0.2 0.1 0 r l = 350 ? v cc = 5.0 v, t a = 25oc 1.0 k ? 4.0 k ? , 4.7 k ? i ol = 16.0 ma 13.0 ma 10.0 ma 6.0 ma ambient te mperature t a ( o c) maximum forward current i f (ma) maximum fo rw ard curren t vs. ambien t temperat ure ambient te mperature t a ( o c) detector power dissipation p c (mw) detect or power dissi pat io n vs. ambien t temperat ure forward v oltage v f (v) forward current i f (ma) for wa rd curren t vs. fo rw ard volta ge ambient te mperature t a ( o c) high level supply current i cch (ma) low level supply current i ccl (ma) supply curren t vs. ambient tempera ture input current i f (ma) output v oltage v o (v) output vo lta ge vs. inpu t curren t ambient te mperature t a ( o c) low level output v oltage v ol (v) low level output volt age vs. ambient tempera tur e
ps9117 v cc = 5.0 v, v o = 0.6 v 5 4 3 2 1 0 100 80 60 40 20 0 -50 -25 0 25 50 7 5 100 -50 -25 0 25 50 7 5 100 1.0 k ? r l = 350 ? i f = 7.5 ma, v cc = 5.0 v t phl : r l = 350 ? , 1.0 k ? , 4.0 k ? 4.0 k ? t plh : r l = 4.7 k ? t plh : r l = 1.0 k ? t plh : r l = 350 ? -50 -25 0 25 50 7 5 100 i f = 7.5 ma, v cc = 5.0 v 300 250 200 150 100 50 0 t r : r l = 4.7 k ? t r : r l = 350 ? t f : r l = 350 ? , 1.0 k ? , 4.0 k ? t r : r l = 1.0 k ? ambient t emperature t a (oc) threshold input current i fhl (ma) threshold input current vs. ambient tempera ture ambient t emperature t a (oc) propagation delay ti me t phl , t plh (ns) prop agat ion dela y time vs. ambient tempera ture ambient t emperature t a (oc) pulse width distortion t phl ?t plh (ns) pulse width dist or tion vs. ambient tempera ture ambient te mperature t a (oc) switching ti me t r , t f (ns) switching time vs. ambient tempera ture input current i f (ma) propagation delay t ime t phl , t plh (ns) prop agation dela y time vs. input current 60 50 40 30 20 10 0 -50 -25 0 25 50 7 5 100 i f = 7.5 ma, v cc = 5.0 v r l = 4.7 k ? r l = 350 ? 1.0 k ? 15 13 11 9 7 5 120 100 80 60 40 20 0 t plh : r l = 4.7 k ? t plh : r l = 1.0 k ? t phl : r l = 350 ? , 1.0 k ? , 4.7 k ? t plh : r l = 350 ? 3
ps9117 taping specifications (unit:mm) outline and dimensions (t ape) tape direction ps91 17-f3 ps91 17-f4 outline and dimensions (reel) packing: 2 500 pcs/reel 1001.0 13.00.2 3302.0 2.00.5 11 .9 to 15.4 outer edge of flange 17.51.0 13.51.0 2.00.5 13.00.2 r 1.0 21.00.8 1.550.1 2.00.05 4.00.1 1.750.1 3.90.1 3.45 max. 7.40.1 0.30.05 8.00.1 1.5 +0. 1 -0 5.50.1 12.00.2 3.00.1
ps9117 notes on handling 1. recommended soldering conditions (1) infrared re?ow soldering ? peak re?ow temperature 260 c or below (package surface temperature) ? time of peak re?ow temperature 10 seconds or less ? time of temperature higher than 220 c 60 seconds or less ? time to preheat temperature from 120 to 180 c 120 30 s ? number of re?ows three ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (2) wave soldering ? temperature 260 c or below (molten solder temperature) ? time 10 seconds or less ? preheating conditions 120 c or below (package surface temperature) ? number of times one (allowed to be dipped in solder including plastic mold portion.) ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (3) soldering by soldering iron ? peak temperature (lead part temperature) 350 c or below ? time (each pins) 3 seconds or less ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (a) soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) please be sure that the temperature of the package would not be heated over 100 c 12030 s (preheating) 220?c 180oc package surface t emperature t (oc) t ime (s) recommended temperature profile of infrared reflow (heating) to 10 s to 60 s 260oc max. 120oc
ps9117 life support applications these nec products are not intended for use in life support devices, appliances, or systems where the malfunction of these prod ucts can reasonably be expected to result in personal injury . the customers of cel using or selling these products for use in such applications do so at their own risk and agree to fully indemnify cel for all damages resulting from such improper use or sale. a business partner of nec compound semiconductor devices, ltd. 04/04/2005 (4) cautions ? fluxes avoid removing the residual ?ux with freon-based and chlorine-based cleaning solvent. 2. cautions regarding noise be aware that when voltage is applied suddenly between the photocouplers input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. usage cautions 1. protect against static electricity when handling. 2. avoid storage at a high temperature and high humidity.
|
