1 dip switch a6t/a6s low-cost dip switch with slide pins allows automatic mounting with dip ic insertion machines. washable models with seal tape are available. smt (surface-mounted terminal) models are available. ordering information no. of l flat actuated raised actuator flat actuated raised actuator poles standard w ith seal tape standard w ith seal tape dip terminal dip terminal dip terminal smt terminal smt terminal smt terminal 1 a6t-1101 a6t-1102 a6t-1104 --- --- --- 2 a6t-2101 a6t-2102 a6t-2104 a6s-2101 a6s-2102 a6s-2104 3 --- --- --- a6s-3101 a6s-3102 a6s-3104 4 a6t-4101 a6t-4102 a6t-4104 a6s-4101 A6S-4102 a6s-4104 5 --- --- --- a6s-5101 a6s-5102 a6s-5105 6 a6t-6101 a6t-6102 a6t-6104 a6s-6101 a6s-6102 a6s-6104 7 --- --- --- a6s-7101 a6s-7102 a6s-7104 8 a6t-8101 a6t-8102 a6t-8104 a6s-8101 a6s-8102 a6s-8104 9 --- --- --- a6s-9101 a6s-9102 a6s-9104 10 a6t-0101 a6t-0102 a6t-0104 a6s-0101 a6s-0102 a6s-0104
a6t/a6s a6t/a6s 2 specifications ratings/characteristics switching capacity 25 ma at 24 vdc insulation resistance 100 m w min. (at 250 vdc) contact resistance 200 m w max. (initial value) dielectric strength 500 v ac for 1 min between terminals of same polarity , and between terminals of dif ferent polarity v ibration resistance malfunction: 10 to 55 hz, 1.5-mm double amplitude shock resistance malfunction: 300 m/s 2 min. (approx. 30g min.) life expectancy mechanical: 1,000 operations min. electrical: 1,000 operations min. ambient temperature operating: 20 c to 70 c (with no icing) ambient humidity operating: 35% to 90% operating force 0.29 n min. (30 gf) flammability rating ul 94-0 dimensions note: 1. all units are in millimeters unless otherwise indicated. 2. unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. flat actuated with dip terminal standard/with seal tape a6t- 101 a6t- 102 flat actuated standard w ith seal t ape raised actuator seal tape (t = 0.06) raised actuator with dip terminal a6t- 104 pcb dimensions (t op v iew) 1.0 0.05 dia. p: pole numbers no. of poles model a 1 a6t-1101 a6t-1102 a6t-1104 3.48 2 a6t-2101 a6t-2102 a6t-2104 6.02 4 a6t-4101 a6t-4102 a6t-4104 11.10 6 a6t-6101 a6t-6102 a6t-6104 16.18 8 a6t-8101 a6t-8102 a6t-8104 21.26 10 a6t-0101 a6t-0102 a6t-0104 26.34
a6t/a6s a6t/a6s 3 flat actuated with smt terminal standard/with seal tape a6s- 101 a6s- 102 flat actuated standard w ith seal t ape raised actuator seal tape (t = 0.06) raised actuator with smt terminal a6s- 104 pcb dimensions (t op v iew) p: pole numbers no. of poles model a 2 a6s-2101 a6s-2102 a6s-2104 6.02 3 a6s-3101 a6s-3102 a6s-3104 8.56 4 a6s-4101 A6S-4102 a6s-4104 11.10 5 a6s-5101 a6s-5102 a6s-5104 13.64 6 a6s-6101 a6s-6102 a6s-6104 16.18 7 a6s-7101 a6s-7102 a6s-7104 18.72 8 a6s-8101 a6s-8102 a6s-8104 21.26 9 a6s-9101 a6s-9102 a6s-9104 23.80 10 a6s-0101 a6s-0102 a6s-0104 26.34 installation internal connections (top view) precautions circuit design use the dip switch within the rated voltage and current ranges, otherwise the dip switch may have a shortened life expectancy, radiate heat, or burn out. mounting do not operate the dip switch while mounting, soldering, or wash - ing the dip switch, otherwise the dip switch may deform due the heat of the solder, the dip switch may malfunction due to the pe- netration of the washing agent, or the machine incorporating the dip switch may operate or be set incorrectly . an automatic insertion machine incorporating a body stopper is available for mounting the dip switch. when using an automatic in - sertion machine incorporating a half-lead stopper to mount the dip switch, make sure that the automatic insertion machine will not de - form the terminals of the dip switch, otherwise the improper inser - tion of the dip switch may result.
a6t/a6s a6t/a6s 4 soldering observe the following conditions when soldering the dip switch. automatic soldering bath soldering temperature: 260 c max. soldering time: 5 s max. for a 1.6-mm thick, single-side pcb reflow soldering soldering time soldering temperature ( c) 2 minutes max. 20 seconds max. manual soldering soldering temperature: 350 c at the tip of the soldering iron. soldering time: 3 s max. for a 1.6-mm thick, single-side pcb set the pins of the dip switch to off before soldering the dip switch. before soldering the dip switch on a pcb, make sure that there is no unnecessary space between the dip switch and pcb. before soldering the dip switch on a multilayer pcb, make sure that the dip switch will not be deformed by the soldering heat on the pattern or land of the multilayer pcb. do not solder the dip switch more than twice including rectification soldering. an interval of five minutes is required between the first and second solderings. make sure that there is no flux rise on the surface of the pcb. pcb surface flux washing washable a6t (with seal tape), a6s (with seal tape) not washable a6t (standard/raised actuator), a6s (standard/raised actuator) ultrasonic cleaning is unavailable to any a6t or a6s-series dip switch with a seal tape. it is possible to wipe or dip these models into washing agents for one minute maximum. apply fluorocarbon or alcoholic solvents to clean washable models. do not apply any other solvents or water to clean any washable model because they may deteriorate the materials or performance of the model. washing equipment incorporating more than one washing bath can be used to clean washable models provided that the washable mod - els are cleaned for one minute maximum per bath and the total cleaning time does not exceed three minutes. do not impose any external force on washable models while wash - ing. do not clean washable models immediately after soldering. w ait for at least three minutes to clean washable models after soldering. the a6t or a6s-series dip switch with a seal tape can be washed provided that the seal tape is not removed or pasted before washing the dip switch.
a6t/a6s a6t/a6s 5 handling do not apply excessive operating force to the dip switch, otherwise the dip switch may be damaged or deformed, thus causing the switch mechanism to malfunction as a result. apply an operating force not exceeding 200% of the maximum rated operating force to the dip switch. set the dip switch incorporating slide pins with a tiny , rounded ob - ject, such as the tip of a ball-point pen or small screwdriver . do not set the dip switch using tweezers or any other sharp object, which may damage the dip switch. do not set the dip switch using the point of a mechanical pencil, otherwise lead powder or fragments may fall into the dip switch and internal circuit board, causing the dip switch to malfunction and reducing the dielectric strength of the circuit board. omron corporation control components division h.q. 28th fl., crystal t ower bldg. 1-2-27, shiromi, chuo-ku, osaka 540 japan phone: 06-949-61 15 fax: 06-949-6134 all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.03937. t o convert grams into ounces, multiply by 0.03527. cat. no. a102-e1-1 in the interest of product improvement, specifications are subject to change without notice. printed in japan 0996-1m (0996) a
|
