2-12 accelerometer C unamplified model 3022 pc board mountable accelerometer millivolt output low cost t vibration/shock monitoring t modal analysis t motion control t crash testing t aerospace features t adhesive mount t 0.5% non-linearity (typical) t 1.0% temperature performance (with comp resistorstypical) t dc response t built-in damping t built-in overrange stops t low power t pins or no pins standard ranges range g range g 2 c 50 c 5 c 100 c 10 c 200 c 20 c 500 c description the model 3022 is a piezoresistive silicon accelerometer. it is packaged on a ceramic substrate with an epoxy sealed ceramic cover and is designed for adhesive mounting. a detailed calibration sheet provides test data and resistor compensation values for each sensor. the accelerometer consists of a micro machined silicon mass suspended by multiple beams from a silicon frame. piezoresistors located in the beams change their resistance as the motion of the suspended mass changes the strain in the beams. silicon caps on the top and bottom of the device are added to provide over-range stops. this design provides for a very low profile, high shock resistance, durability and built-in damping over a wide usable bandwidth. each sensor is individually serialized. for an accelerometer with a mounting bracket designed to bolt the sensor to a mounting location, see the model 3028. please refer to the models 3052 and 3058 for accelerometers with integral temperature compensation.
pc board mountable accelerometer model 3022 accelerometer C unamplified 2-13 april 2000 calibration data figure 1. calibration data sheet a calibration data sheet similar to the sample shown above is included with each unit. the calibration sheet provides the measured test and calibration data for the sensor. in addition to the test data, the values of calibration and temperature compensation resistors are also included. signal conditioning figure 2. typical temperature compensation and amplification circuit (component values specified for each sensor) q1: 2n3904 cr1: 1n914 or equivalent op amps: lt1014, lm324 or equivalent ? rstc sets the excitation voltage ramp to compensate the sensitivity error due to temperature. ? rset sets the excitation voltage to 5v at 25c. ? rzb1, rzb2 and rztc1 and rztc2 calibrate the zero offset and compensate the offset error due to temperature. ? rs calibrates the output span. ? vcc must be >8 vdc.
model 3022 pc board mountable accelerometer 2-14 accelerometer C unamplified performance specifications supply voltage: 5.0 vdc ambient temperature: 25c (unless otherwise specified) notes 1. the frequency response is defined as the range of frequencies over which the device sensitivity is within 5% of the dc value. 2. output voltage increases for positive acceleration; output voltage decreases for negative acceleration. 3. percentage values are with external compensation. the uncompensated temperature coefficients are measured and specified with each unit. in addition, the values of the resistors that provide a temperature compensated output are provided with each unit. these resistors are for use in the circuit shown in figure 2. 4. best fit straight line. for full scale ranges of 10g or less, the maximum non-linearity is 2%. 5. compensated temperature range: 0-50c in reference to 25c. 6. 10 hz to 1 khz. 7. 400g for 2g, 5g, and 10g versions. 20x or 2000g for other versions, whichever is less. 8. for sensors having a resonant frequency greater than 5 khz, the calibration data sheet will indicate ">5 khz." in addition, the damping ratio will indicate n/a. 9. actual test data for this parameter is included on the calibration sheet provided with each sensor. a sample of this calibration sheet is shown as figure 1. parameters range units notes 2g 5g 10g 20g frequency response [min] 0-250 0-300 0-400 0-600 hz 1, 9 mounted resonant frequency [min] 700 800 1000 1500 hz 8, 9 sensitivity (min/max) 8.0/20.0 6.0/15.0 3.0/6.0 1.5/3.0 mv/g 2 parameters range units notes 50g 100g 200g 500g frequency response [min] 0-1000 0-1500 0-2000 0-2400 hz 1, 9 mounted resonant frequency [min] 2000 3000 4000 5000 hz 8, 9 sensitivity (min/max) 0.6/1.5 0.3/0.6 0.15/0.3 0.06/0.15 mv/g 2 parameters min typ max units notes zero acceleration output 5.0 25.0 mv 9 damping ratio 0.4 0.7 0.9 8, 9 non-linearity 0.5 1.0 % span 4 transverse sensitivity 1.0 3.0 % span input & output resistance 2.5 3.5 6.5 k w 9 temperature error - span 1.0 2.0 % span 3, 5 temperature error - zero 1.0 2.0 % span 3, 5 supply voltage 5.0 10.0 vdc output noise 1.0 v p-p 6 output load resistance 5 m w acceleration limits (any direction) 20x rated 7 operating temperature -40c to +125c storage temperature -55c to +150c weight (with pins) 6.5 grams materials alumina ceramic substrate with alumina ceramic cap
pc board mountable accelerometer model 3022 accelerometer C unamplified 2-15 april 2000 ordering information connections ltr 2 - 10 g 20 - 500 g a d i m 0.300 0.005 [7.62 0.13] 0.265 0.005 [6.73 0.13] b dim 0.250 0.005 [6.35 0.13] 0.240 0.005 [6.10 0.13] c dim 0.032 0.004 [0.81 0.10] 0.032 0.004 [0.81 0.10]
|