View APL5901-25UC_629434.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APL5901/2
Low IQ, Low Dropout 900mA Fixed Voltage Regulator
Features
* * * * * * * * * * * * * * * * Low Noise : 50VRMS (100Hz to 100kHz) Low Quiescent Current : 50A (No load) Low Dropout Voltage : 210mV (@900mA) Very low Shutdown Current : < 1A Fixed Output Voltage : 1.3V ~ 3.4V Stable with 4.7F Output Capacitor Stable with Aluminum , Tantalum or Ceramic Capacitors . Reverse Current Protection No Protection Diodes Needed Built in Thermal Protection Built in Current Limit Protection Controlled Short Circuit Current : 200mA Fast Transient Response Short Setting Time SOT-89, SOT-89-5, SOT-223, SO-8 ,TO-252 and TO-252-5 Packages Lead Free Available (RoHS Compliant)
Design with an internal P-channel MOSFET pass transistor, the APL5901/2 maintains a low supply current, independent of the load current and dropout voltage. Other features include reverse current protection, thermal-shutdown protection, current limit protection to ensure specified output current and controlled short-circuit current. The APL5901/2 regulator come in a miniature SOT-89, SOT-89-5, SOT-223, SO8, TO-252 and TO-252-5 packages.
Pin Configuration
APL5901
BP
TAB is GND
GND SHDN
5
1 2 3
4 2 3
1
V IN
GND
VOUT
VOUT GND
VIN
SOT-89 (Top View)
SOT-89-5 (Top View)
TAB is GND
Applications
IN 1 2 3 4 8 7 6 5 OUT GND GND
* * *
Notebook Computer PDA or Portable Equipments Noise-Sensitive Instrumentation Systems
GND GND SHDN
1
BYP
2
3
General Description
The APL5901/2 is micropower, low noise, low dropout linear regulator. Operate from 2.7V to 6V input voltage and deliver up to 900mA. Typical output noise is just 50VRMS with the addition of an external 0.1F bypass capacitor in BP pin and typical dropout voltage is only 210mV at 900mA loading. Designed for use in battery-powered system, the low 50A quiescent current makes it an ideal choice.
VIN
GND
VOUT
SO-8 (Top View)
TAB is GND
SOT-223 (Top View)
VOUT BP GND SHDN VIN
TAB is GND
1
2
3
VIN
VOUT
TO-252 (Top View)
TO-252-5 (Top View)
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005 1 www.anpec.com.tw
1
2
3
4
5
APL5901/2
Pin Configuration (Cont.)
APL5902
TAB is V OUT
1
2
3
GND VOUT
VIN
SOT-223 (Top View)
Ordering and Marking Information
APL5901/2 Lead Free Code Handling Code Temp. Range Package Code Voltage Code Package Code D : S OT-89 D5 : SOT-89-5 U : TO-252 U5 : TO-252-5 V : SOT-223 K : SO-8 Temp. Range C : 0 to 70 C Handling Code TR : Tape & Reel Voltage Code : 13 : 1.3V ~ 34 : 3.4V Lead Free Code L : Lead Free Device Blank : Original Device XXXXX - Date Code , 13 - 1.3V
APL5901/2 - 13 D/V/K :
APL5901/2 XXXXX13 13 APL5901/2 XXXXX
APL5901/2 - 13 U :
XXXXX - Date Code , 13 - 1.3V
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte in plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature.
Pin Description
No. 1 2 3 4 5 PIN Name VIN GND SHDN BP(Note1) VOUT
(Note1)
I/O I
Description Supply voltage input. Ground pins of the circuitry, and all ground pins must be soldered to PCB with proper power dissipation. Shutdown control pin, low = off , high = normal. Don' leave open. t Bypass signal pin in fixed output type device Output pin of the regulator.
I O O
Note1 : These pins do not exist in 3-pin package.
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005 2 www.anpec.com.tw
APL5901/2
Absolute Maximum Ratings
Symbol VIN, VOUT SHDN Parameter Input Voltage or Out Voltage Shutdown Control Pin Rating 6.5 6.5 SOT-89 : 180 SOT-223 : 135 SO-8 : 150 TO-252 : 50 SOT-89 : 38 SOT-223 : 15 SO-8 : 20 TO-252 : 6 Internally Limited 0 to 125 0 to 150 -65 to +150 260 C C Unit V V
RTH,JA
Thermal Resistance - Junction to Ambient
C/W
RTH,JC PD TJ
Thermal Resistance - Junction to Case
C/W W C
Power Dissipation Operating Junction Temperature Control Section Power Transistor Storage Temperature Range Lead Temperature (Soldering, 10 second)
TSTG TL
Electrical Characteristics
Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1F, COUT=4.7F, SHDN=VIN, TJ=0 to 125C. Typical values refer to TJ=25C.
Symbol VIN VOUT ILIMIT ISHORT IOUT Parameter Input Voltage Output Voltage Circuit Current Limit Short Current Load Current Test Conditions APL5901/2 Min. Typ. Max. 2.7 6 Unit V V A mA mA 10 6 1300 1050 700 380 dB 100 450 1 A A mV mV % mV
VOUT+1.0V< VCC<6.0V, 0mA< IOUT < IMAX VOUT -2% VOUT VOUT +2% VIN=4.3V 1.5 VOUT=0V 900 VOUT+0.5V< VCC<6.0V, I = 1mA VIN =VOUT+1.0V, 0mA< IOUT < IMAX 1.3VVOUT<1.5V 515X 4 1 0.1 1100 900 500 280 55 65 50 370 0.01
3
200
REGLINE Line Regulation REGLOAD Load Regulation
(Note2)
VDROP
Dropout Voltage
IOUT =900mA
1.5VVOUT<2V 2VVOUT<2.5V 2.5VVOUT<3.4V
PSRR Ripple Rejection IQ Quiescent Current Shutdown Supply (Note3) Current
F1kHz, 1Vpp at VIN = VOUT+1.0V C load No =10nf IOUT=900mA Shutdown = low IOUT=0, VCC =6.0V
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
www.anpec.com.tw
APL5901/2
Electrical Characteristics (Cont.)
Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1F, COUT=4.7F, SHDN=VIN, TJ=0 to 125C. Typical values refer to TJ=25C.
Symbol Parameter Test Conditions 100HzNoise IQ
(Note3)
Shutdown Recovery (Note3) Delay OTS Over Temperature Shutdown Over Temperature Shutdown Hysteresis Output Voltage Temperature Coefficient Output Capacitor
TC COUT
ESR 0.02 0.1 1 Ohm Shutdown Input VOUT+1.0V< VIN <6.0V 0.4 0.7 1.6 V Threshold(Note3) Shutdown input Bias ISHDN VSHDN =VIN 0.01 100 nA current(Note3) Input Reverse Leakage A VOUT-VIN=0.1V 0.1 0.5 current Reverse Protection 11 50 mV Threshold Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V Note 3 : For 5-pin devices only.
Application Circuit
INPUT 2.7V to 6V VIN APL5901 on off CBP 0.01F SHDN GND BP COUT 4.7F VOUT VOUT
CIN 1F
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
4
www.anpec.com.tw
APL5901/2
Typical Characteristics
3
APL5901/2-33
Ground Pin Current vs. Load Current (uA)
Current Limit vs. Input Voltage
Ground Pin Current vs. Output Current
400 350 300 250 200 150 100 50 0 0 150 300 450 600 750 900
APL5901/2-33
2.5
Current Limit (mA)
2
1.5
1
0.5
0 3.5 4 4.5 5 5.5 6
Input Voltage (V)
Output Current (mA)
Ground Pin Current vs. Load Current (uA)
Ground Pin Current vs. Input Voltage
350 300
APL5901/2-33
Input Voltage vs. Output Voltage
3.5 3
APL5901/2-33
Output Voltage (V)
250 200 150 100 50 0 0 1 2 3 4 5 6
2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6
Input Voltage (V)
Input Voltage (V)
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
5
www.anpec.com.tw
APL5901/2
Typical Characteristics
Dropout Voltage vs. Output Current
1200 1100 1000
Output Current vs. Output Voltage
0
APL5901/2-33
VOUT=1.5V
-2
Dropout Voltage (mV)
900 800 700 600 500 400 300 200 100 0 0 150 300 450 600 750 900
Output Current (uA)
VOUT=1.8V
-4
VIN=0V
-6
VOUT=3.3V VOUT=2.5V
-8
-10
-12 0 0.5 1 1.5 2 2.5 3
Output Current (mA)
Output Voltage (V)
SHDN Threshold Voltage vs. Input Voltage
1
APL5901/2-33
PSRR vs. Frequency
APL5901/2-33
+0
SHDN Threshold Voltage (V)
0.9
-10 -20
0.8
PSRR (dB)
VIN=0V
-30 -40 -50 -60 -70
VIN=4V IOUT =50mA COUT=10uF CBP=0.1uF
0.7
0.6
0.5
-80 -90
VIN=5V
0.4 3 3.5 4 4.5 5 5.5 6
-100
20
50 100 200
500 1k
2k
5k 10k 20k
50k 100k 200k
Input Voltage (V)
Frequency (HZ)
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
6
www.anpec.com.tw
APL5901/2
Typical Characteristics
Output Noise
100u
APL5901/2-33
Output Noise vs. Bypass Capacitor
500 450 400
APL5901/2-33
VIN=4.3V 80u IOUT =0mA COUT=10uF 60u CBP=0.1uF
VOUT (50uV/div)
20u 0 -20u -40u -60u -80u
Output Noise (uV)
0 2m 4m 6m 8m 10m
40u
350 300 250 200 150 100 50 0 0 0.1 0.2 0.3 0.4
-100u
Time (s)
Bypass Capacitor (uF)
Load-Transient Response
APL5901/2-33
Line-Transient Response
APL5901/2-33
Output Voltage (50mV/div)
VOUT VIN=VOUT+1V COUT=4.7F
Output Voltage (20mV/div)
VIN 4V 3V
VOUT
IOUT=1mA~900mA
Time (10s/div)
Time (40s/div)
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
7
www.anpec.com.tw
APL5901/2
Typical Characteristics
Shutdown Exit Delay
APL5901/2-33
Shutdown Exit Delay
APL5901/2-33
3.3V
3.3V
VOUT 0V
VOUT CBP=10nF No Load 0V 4V 4V vSHDN CBP=100nF No Load
vSHDN
0V
0V
Time (1ms/div)
Time (20ms/div)
Entering Shutdown
APL5901/2-33
Region of Stable ESR vs. Load Current
1
APL5901/2-33
3.3V VOUT
0.1
VOUT=3.3V
COUT=1F No Load 0V 4V
COUT ESR ()
stable
0.01
unstable 0V
0.001 0 150 300 450 600 750 900
Time (200ms/div)
Load Current (mA)
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
8
www.anpec.com.tw
APL5901/2
Typical Characteristics
Output Voltage vs. Temperature
3.35
APL5901/2-33
3.33
Output Voltage (V)
3.31
3.29
3.27
3.25 -40 0 40 80 120
Temperature (C )
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
9
www.anpec.com.tw
APL5901/2
Application Information
Capacitor Selection and Regulator Stability
The APL5901/2 use at least a 1F capacitor on the input, and this capacitor can be Aluminum, Tantalum or Ceramic capacitor. The input capacitor with larger value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use Aluminum, Tantalum or Ceramic capacitor, and a minimum value of 4.7F and ESR above 0.02 is recommended. A larger output capacitor can reduce noise and improve load-transient response, stability, and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature. When using this capacitor, a minimum 10uF or more may be required to ensure the stability at low temperature operation. Use a bypass capacitor at BP pin for low output nvise. Increasing the capacitance will slightly decrease the output noise, but increase the start-up time.
Reverse Current Protection
The APL5901/2 have an internal reverse protection, it does not need an external schottky diode to connect the regulator input and output. If the output voltage is forced above the input voltage by more than 11mV, the IC will be shutdown and the ground pin current is below 0.1uA.
Shutdown/Enable
The APL5901/2 have an active high enable function. Force EN high (>1.6V) enables the regulator, EN low (<0.4V) disables the regulator and enter the shutdown mode. In shutdown mode, the quiescent current can reduce below 1uA. The EN pin cannot be floating, a floating EN pin may cause an indeterminate state on the output. If it is no use, connect to VIN for normal operation.
Load-Transient Considerations
The APL5901/2 load-transient response graphs in typical characteristics show the transient response. A step change in the load current from 10mA to 900mA at 10s will cause a 20mV transient spike. Larger output capacitor and lower ESR can reduce transient spike.
Current Limit
The APL5901/2 have a current limit protection. The ouptut voltage will drop close to zero volt, when load current reaches the limit, and then the load current will be limited at 200mA after output voltage is below 0.7V. When the load current back to the value where limiting started, the output voltage and current will return to normal value. When output is shorted to ground, the APL5901/2 will keep short circuit current at 200mA .
Input-Output (Dropout)Voltage
The minimum input-output voltage difference (dropout) determines the lowest usable supply voltage. In battery-powered systems, this will determine the useful end-of-life battery voltage. Because the APL5901/2 use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (RDS(ON)) multiplied by the load current.
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005 10
www.anpec.com.tw
APL5901/2
Thermal Protection
Thermal protection limits total power dissipation in the device. When the junction temperature exceeds TJ=+150J, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to cool. When the IC' junction temperature is down by s 10J, the thermal sensor will turn the pass transistor on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed to protect the APL5901/2 in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature of TJ=+150J.
Operating Region and Power Dissipation
The thermal resistance of the case to circuit board, and the rate of air flow all control the APL5901/2' s maximum power dissipation. The power dissipation across the device is PD = IOUT (VIN-VOUT) and the maximum power dissipation is: PDMAX = (TJ-T A) / (c JC + c CA) where TJ-TA is the temperature difference between the junction and ambient air, c JC is the thermal resistance of the package, and c CA is the thermal resistance through the printed circuit board, copper traces, and other materials to the ambient air. The GND pin of the APL5901 provide an electrical connection to ground and channeling heat away. If power dissipation is large, connect the GND pin to ground using a large pad or ground plane, can improve the problem of over heat of IC.
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
11
www.anpec.com.tw
APL5901/2
Packaging Information
SOP-8 pin ( Reference JEDEC Registration MS-012)
E
H
e1 D
e2
A1
A
1 L
0.004max.
Dim A A1 D E H L e1 e2 1
Millimeters Min. 1.35 0.10 4.80 3.80 5.80 0.40 0.33 1.27BSC 8 Max. 1.75 0.25 5.00 4.00 6.20 1.27 0.51 Min. 0.053 0.004 0.189 0.150 0.228 0.016 0.013
0.015X45
Inches Max. 0.069 0.010 0.197 0.157 0.244 0.050 0.020 0.50BSC 8
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
12
www.anpec.com.tw
APL5901/2
Packaging Information
SOT-223( Reference JEDEC Registration SOT-223)
D B1
A c
a
H
E L K e e1 b A1
B
Dim A A1 B B1 c D E e e1 H L K Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30
Millimeters Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0 13
13
Inches Min. 0.06 0.02 0.11 0.01 0.25 0.13 0.09 BSC 0.18 BSC 7.30 1.10 2.00 10 0.26 0.04 0.06 0 13
www.anpec.com.tw
Max. 0.07 0.03 0.12 0.01 0.26 0.15
0.29 0.04 0.08 10
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
APL5901/2
Packaging Information
SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)
D
D1
a E H 1 2 3
L B1 B e e1 C
A a
Dim A B B1 C D D1 e e1 E H L
Millimeters Min. 1.40 0.40 0.35 0.35 4.40 1.35 1.50 BSC 3.00 BSC 2.29 3.75 0.80 2.60 4.25 1.20 10 0.090 0.148 0.031 Max. 1.60 0.56 0.48 0.44 4.60 1.83 Min. 0.055 0.016 0.014 0.014 0.173 0.053
Inches Max. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 BSC 0.102 0.167 0.047 10
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
14
www.anpec.com.tw
APL5901/2
Packaging Information
SOT-89-5
Dim A B C D E F G H I J K L
Millimeters Min. 4.40 4.05 1.50 1.30 2.40 0.80 3.00 REF 1.50 REF 0.40 1.40 0.35 5 TYP 0.52 1.60 0.41 0.01 0.05 0.01 Max. 4.60 4.25 1.70 1.50 2.60 Min. 0.17 0.16 0.06 0.05 0.09 0.03
Inches Max. 0.18 0.17 0.07 0.06 0.1 0.12 REF 0.06 REF 0.02 0.06 0.02 0.2 TYP
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
15
www.anpec.com.tw
APL5901/2
Packaging Information
TO-252-5
A B H J
M D
C
L S P K
Dim A B C D P S H J K L M
Millimeters Min. 6.40 5.20 6.80 2.20 1.27 REF 0.50 2.20 0.45 0 0.90 5.40 0.80 2.40 0.55 0.15 1.50 5.80 0.02 0.08 0.01 0 0.03 0.21 Max. 6.80 5.50 7.20 2.80 Min. 0.25 0.20 0.26 0.08
Inches Max. 0.26 0.21 0.27 0.11 0.05 REF 0.03 0.09 0.02 0.006 0.06 0.22
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
16
www.anpec.com.tw
APL5901/2
Packaging Information
TO-252( Reference JEDEC Registration TO-252)
E b2 L2 A C1
D H L1 L b e1 C A1
Dim A A1 b b2 C C1 D E e1 H L L1 L2
Rev. B.2 - May., 2005
Millimeters Min. 2.18 0.89 0.508 5.207 0.46 0.46 5.334 6.35 3.96 9.398 0.51 0.64 0.89 1.02 2.032
17
Inches Max. 2.39 1.27 0.89 5.461 0.58 0.58 6.22 6.73 5.18 10.41 Min. 0.086 0.035 0.020 0.205 0.018 0.018 0.210 0.250 0.156 0.370 0.020 0.025 0.035 0.040 0.080
www.anpec.com.tw
Max. 0.094 0.050 0.035 0.215 0.023 0.023 0.245 0.265 0.204 0.410
Copyright (c) ANPEC Electronics Corp.
APL5901/2
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
TP
(IR/Convection or VPR Reflow)
tp Critical Zone T L to T P
Ramp-up
Temperature
TL Tsmax
tL
Tsmin Ramp-down ts Preheat
25
t 25 C to Peak
Time
Classificatin Reflow Profiles
Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (T L) - Time (tL) Peak/Classificatioon Temperature (Tp) Time within 5C of actual Peak Temperature (tp) Ramp-down Rate Sn-Pb Eutectic Assembly 3C/second max. 100C 150C 60-120 seconds 183C 60-150 seconds See table 1 10-30 seconds Pb-Free Assembly 3C/second max. 150C 200C 60-180 seconds 217C 60-150 seconds See table 2 20-40 seconds
6C/second max. 6C/second max. 6 minutes max. 8 minutes max. Time 25C to Peak Temperature Notes: All temperatures refer to topside of the package .Measured on the body surface. (mm)
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005 18 www.anpec.com.tw
APL5901/2
Classification Reflow Profiles(Cont.)
Table 1. SnPb Entectic Process - Package Peak Reflow Temperature s 3 3 Package Thickness Volume mm Volume mm <350 350 <2.5 mm 240 +0/-5C 225 +0/-5C 2.5 mm 225 +0/-5C 225 +0/-5C
Table 2. Pb-free Process - Package Classification Reflow Temperatures 3 3 3 Package Thickness Volume mm Volume mm Volume mm <350 350-2000 >2000 <1.6 mm 260 +0C* 260 +0C* 260 +0C* 1.6 mm - 2.5 mm 260 +0C* 250 +0C* 245 +0C* 2.5 mm 250 +0C* 245 +0C* 245 +0C* *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0C. For example 260C+0C) at the rated MSL level.
Reliability Test Program
Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245C, 5 SEC 1000 Hrs Bias @125C 168 Hrs, 100%RH, 121C -65C~150C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA
Carrier Tape & Reel Dimensions
t P P1 D
Po E
F W
Bo
Ao
Ko D1
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
19
www.anpec.com.tw
APL5901/2
Carrier Tape & Reel Dimensions(Cont.)
T2
J C A B
T1
Reel Dimensions
Application A 330 1 SOP- 8 F 5.5 1 Application A 178 1 SOT-89 F 5.5 0.05 Application A 3301 SOT-223 F 5.5 0.05 Application A 330 3 TO-252 F 7.5 0.1 B 62 +1.5 D 1.55 +0.1 B 70 2 D 1.5 0.1 B 621.5 D 1.5+ 0.1 B 100 2 D 1.5 +0.1 C 12.75+ 0.15 D1 1.55+ 0.25 C 13.5 0.15 D1 1.5 0.1 C 12.75 0.15 D1 1.5+ 0.1 C 13 0. 5 D1 1.5 0.25 J 2 0.5 Po 4.0 0.1 J 3 0.15 Po 4.0 0.1 J 2 0.6 Po 4.0 0.1 J 2 0.5 Po 4.0 0.1 T1 12.4 0.2 P1 2.0 0.1 T1 14 2 P1 2.0 0.1 T1 12.4 +0.2 P1 2.0 0.05 T1 16.4 + 0.3 -0.2 P1 2.0 0.1 T2 2 0.2 Ao 6.4 0.1 T2 1.3 0.3 Ao 4.8 0.1 T2 2 0.2 Ao 6.9 0.1 T2 2.5 0.5 Ao 6.8 0.1 W 12 0. 3 Bo 5.2 0. 1 W 12 + 0.3 12 - 0.1 Bo 4.5 0.1 W 12 0.3 Bo 7.5 0.1 W 16+ 0.3 - 0.1 Bo 10.4 0.1 P 8 0.1 Ko 2.1 0.1 P 8 0.1 Ko 1.80 0.1 P 8 0.1 Ko 2.1 0.1 P 8 0.1 Ko 2.5 0.1 E 1.75 0.1 t 0.3 0.013 E 1.75 0.1 t 0.3 0.013 E 1.75 0.1 t 0.3 0.05 E 1.75 0.1 t 0.3 0.05
(mm)
Cover Tape Dimensions
Application SOP- 8 SOT- 89 SOT- 223 TO- 252 Carrier Width 12 12 12 16 Cover Tape Width 9.3 9.3 9.3 13.3 Devices Per Reel 2500 1000 2500 2500
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
20
www.anpec.com.tw
APL5901/2
Customer Service
Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369
Copyright (c) ANPEC Electronics Corp. Rev. B.2 - May., 2005
21
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APL5901-25UC

	To Download APL5901-25UC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .