Part Number Hot Search : 
82000 H3900 50P03 CC9318P EL7144 BUW12W 3KA18 E2955
Product Description
Full Text Search
 

To Download PS8502L2-E3-AX Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 PHOTOCOUPLER
PS8502,PS8502L1,PS8502L2,PS8502L3
HIGH SPEED ANALOG OUTPUT TYPE 8 mm CREEPAGE 8-PIN PHOTOCOUPLER
NEPOC Series
DESCRIPTION
The PS8502, PS8502L1, PS8502L2 and PS8502L3 are 8-pin high speed photocouplers containing a GaAIAs LED on input side and a PN photodiode and a high speed amplifier transistor on output side on one chip. The PS8502 is in a plastic DIP (Dual In-line Package) with 8 mm creepage distance product. The PS8502L1 is lead bending type for long creepage distance. The PS8502L2 is lead bending type for long creepage distance (Gull-wing) for surface mount. The PS8502L3 is lead bending type (Gull-wing) for surface mounting.
FEATURES
* Long creepage distance (8 mm MIN.: PS8502L1, PS8502L2) * High common mode transient immunity (CMH, CML = 15 kV/ s MIN.) * High supply voltage (VCC = 35 V MAX.) * High speed response (tPHL, tPLH = 0.8 s MAX.) * High isolation voltage (BV = 5 000 Vr.m.s.) * TTL, CMOS compatible with a resistor * Ordering number of tape product: PS8502L2-E3: 1 000 pcs/reel : PS8502L3-E3: 1 000 pcs/reel * Pb-Free product * Safety standards * UL approved: No. E72422 * CSA approved: No. CA 101391 (CA5A, CAN/CSA-C22.2 60065, 60950) * BSI approved: No. 8937, 8938 * SEMKO approved: No. 615433 * NEMKO approved: No. P06207243 * DEMKO approved: No. 314091 * FIMKO approved: No. FI 22827 * DIN EN60747-5-2 (VDE0884 Part2) approved: No. 40019182 (Option)
APPLICATIONS
* Interface for measurement or control equipment * Substitutions for relays and pulse transformers * Modem, communications device * General purpose inverter
Document No. PN10657EJ04V0DS (4th edition) Date Published September 2009 NS
The mark shows major revised points. The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field.
PS8502,PS8502L1,PS8502L2,PS8502L3

PACKAGE DIMENSIONS (UNIT: mm) DIP Type
Lead Bending Type (Gull-wing) For Surface Mount
2
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
Lead Bending Type For Long Creepage Distance
Lead Bending Type For Long Creepage Distance (Gull-wing) For Surface Mount
Data Sheet PN10657EJ04V0DS
3
PS8502,PS8502L1,PS8502L2,PS8502L3
PHOTOCOUPLER CONSTRUCTION
Parameter Air Distance (MIN.) Outer Creepage Distance (MIN.) Isolation Distance (MIN.) PS8502, PS8502L3 7 mm 7 mm 0.4 mm PS8502L1, PS8502L2 8 mm 8 mm 0.4 mm

MARKING EXAMPLE
4
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
ORDERING INFORMATION
Part Number Order Number Solder Plating Specification PS8502 PS8502L1 PS8502L2 PS8502L3 PS8502L2-E3 PS8502L3-E3 PS8502-V PS8502L1-V PS8502L2-V PS8502L3-V PS8502L2-V-E3 PS8502L3-V-E3 PS8502-AX PS8502L1-AX PS8502L2-AX PS8502L3-AX PS8502L2-E3-AX PS8502L3-E3-AX PS8502-V-AX PS8502L1-V-AX PS8502L2-V-AX PS8502L3-V-AX PS8502L2-V-E3-AX PS8502L3-V-E3-AX Embossed Tape 1 000 pcs/reel Magazine case 50 pcs DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) Embossed Tape 1 000 pcs/reel Pb-Free (Ni/Pd/Au) Magazine case 50 pcs Packing Style Safety Standard Approval Standard products (UL, CSA, BSI, SEMKO, NEMKO, DEMKO, FIMKO approved) Application Part Number*1 PS8502 PS8502L1 PS8502L2 PS8502L3 PS8502L2 PS8502L3 PS8502 PS8502L1 PS8502L2 PS8502L3 PS8502L2 PS8502L3
*1 For the application of the Safety Standard, following part number should be used.
ABSOLUTE MAXIMUM RATINGS (TA = 25 C, unless otherwise specified)
Parameter Diode Forward Current
*1
Symbol IF VR VCC
Ratings 25 5 35
Unit mA V V
Reverse Voltage
Detecto r
Supply Voltage
Output Voltage Output Current Power Dissipation *2 Isolation Voltage
*3
VO IO PC BV TA Tstg
35 8 100 5 000 55 to +100 55 to +125
V mA mW Vr.m.s. C C
Operating Ambient Temperature Storage Temperature
*1 Reduced to 0.33 mA/ C at TA = 70 C or more. *2 Reduced to 2.0 mW/ C at TA = 75 C or more. *3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together.
Data Sheet PN10657EJ04V0DS
5
PS8502,PS8502L1,PS8502L2,PS8502L3
ELECTRICAL CHARACTERISTICS (TA = 25 C)
Parameter Diode Forward Voltage Reverse Current Forward Voltage Temperature Coefficent Symbol VF IR VF/ TA IF = 16 mA VR = 3 V IF = 16 mA 2.1 Conditions MIN. TYP.*1 1.7 MAX. 2.2 10 Unit V A mV/ C

Detector
Terminal Capacitance High Level Output Current High Level Output Current Low Level Output Voltage Low Level Supply Current High Level Supply Current Coupled Current Transfer Ratio Isolation Resistance Isolation Capacitance Propagation Delay Time (H L)
*2
Ct IOH (1) IOH (2) VOL ICCL ICCH CTR RI-O CI-O tPHL
V = 0 V, f = 1 MHz IF = 0 mA, VCC = VO = 5.5 V IF = 0 mA, VCC = VO = 35 V IF = 16 mA, VCC = 4.5 V, IO = 2.4 mA IF = 16 mA, VO = Open, VCC = 35 V IF = 0 mA, VO = Open, VCC = 35 V IF = 16 mA, VCC = 4.5 V, VO = 0.4 V VI-O = 1 kVDC V = 0 V, f = 1 MHz IF = 16 mA, VCC = 5 V, RL = 1.9 k 15 10
11
30 3 500 100 0.15 150 0.01 1 0.4
pF nA A V A A %
0.7 0.22 0.8
pF s
Propagation Delay Time (L H)
*2
tPLH
IF = 16 mA, VCC = 5 V, RL = 1.9 k
0.35
0.8
s
Common Mode Transient Immunity at High Level Output*3 Common Mode Transient Immunity at Low Level Output*3
CMH
IF = 0 mA, VCC = 5 V, VCM = 1.5 kV, RL = 4.1 k
15
kV/ s
CML
IF = 16 mA, VCC = 5 V, VCM = 1.5 kV, RL = 4.1 k
15
kV/ s
6
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
*1 Typical values at TA = 25 C *2 Test circuit for propagation delay time
Remark CL includes probe and stray wiring capacitance. *3 Test circuit for common mode transient immunity
Remark CL includes probe and stray wiring capacitance.
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of more than 0.1
*1
F is used between VCC and GND near device. Also, ensure that the
distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Pins 1, 4 (which is an NC pin) can either be connected directly to the GND pin on the LED side or left open. Also, Pin 7 (which is an NC open. Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this may degrade the internal noise environment of the device. *1 NC: Non-Connection (No Connection) 4. Avoid storage at a high temperature and high humidity.
*1
pin) can either be connected directly to the GND pin on the detector side or left
Data Sheet PN10657EJ04V0DS
7
PS8502,PS8502L1,PS8502L2,PS8502L3

TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise specified)
Remark The graphs indicate nominal characteristics.
8
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
Remark The graphs indicate nominal characteristics.
Data Sheet PN10657EJ04V0DS
9
PS8502,PS8502L1,PS8502L2,PS8502L3
TAPING SPECIFICATIONS (UNIT: mm)
10
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
Data Sheet PN10657EJ04V0DS
11
PS8502,PS8502L1,PS8502L2,PS8502L3
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
12
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
NOTES ON HANDLING 1. Recommended soldering conditions
(1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220 C * Time to preheat temperature from 120 to 180 C * Number of reflows * Flux 260 C or below (package surface temperature) 10 seconds or less 60 seconds or less 120 30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
(2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260 C or below (molten solder temperature) 10 seconds or less 120 C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron * Peak temperature (lead part temperature) * Time (each pins) * Flux 350 C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100 C.
Data Sheet PN10657EJ04V0DS
13
PS8502,PS8502L1,PS8502L2,PS8502L3
(4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler's input and output or between VCCemitters at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings.
14
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3

SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter Climatic test class (IEC 60068-1/DIN EN 60068-1) Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.5 UIORM, Pd 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM, Pd 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) Material group (DIN EN 60664-1 VDE0110 Part 1) Storage temperature range Operating temperature range Isolation resistance, minimum value VIO = 500 V dc at TA = 25C VIO = 500 V dc at TA MAX. at least 100C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi Tstg TA CTI Symbol Speck 55/100/21 Unit
UIORM Upr
1 130 1 695
Vpeak Vpeak
Upr
2 119
Vpeak
UTR
8 000 2 175 III a -55 to +125 -55 to +100 1012 1011
Vpeak
C C
Ris MIN. Ris MIN.
Tsi Isi Psi Ris MIN.
175 400 700 109
C mA mW
Data Sheet PN10657EJ04V0DS
15
PS8502,PS8502L1,PS8502L2,PS8502L3
16
Data Sheet PN10657EJ04V0DS
PS8502,PS8502L1,PS8502L2,PS8502L3
This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.
Caution
GaAs Products


▲Up To Search▲   

 
Price & Availability of PS8502L2-E3-AX

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X