Part Number Hot Search : 
TPCA80 100BF 104M00 XXXXSX BU2508D HY57V16 KBU608 AM1523CE
Product Description
Full Text Search
 

To Download 5962-8957601-XC Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 UT1553B RTR Remote Terminal with RAM
FEATURES
E Complete MIL-STD-1553B remote terminal interface E 1K x 16 of on-chip static RAM for message data,
completely accessible to host
E
Table I of MIL-STD-883, Method 5004, Class B, also Standard Military Drawing available Available in 68-pin pingrid array package
E Self-test capability, including continuous loop-back E E E E E
compare Programmable memory mapping via pointers for efficient use of internal memory, including buffering multiple messages per subaddress RT-RT Terminal Address Compare Command word stored with incoming data for enhanced data management User selectable RAM Busy (RBUSY) signal for slow or fast processor interfacing Full military operating temperature range, -55C to +125C, screened to the specific test methods listed in
INTRODUCTION
The UT1553B RTR is a monolithic CMOS VLSI solution to the requirements of the dual-redundant MIL-STD-1553B interface. Designed to reduce cost and space, the RTR integrates the remote terminal logic with a user-configured 1K x 16 static RAM. In addition, the RTR has a flexible subsystem interface to permit use with most processors or controllers. The RTR provides all protocol, data handling, error checking, and memory control functions, as well as comprehensive self-test capabilities. The RTR's memory meets all of MIL-STD-1553B message storage needs through user-defined memory mapping. This memorymapped architecture allows multiple message buffering at
MCSA(4:0) MODE CODE/ SUBADDRESS OUTPUT MULTIPLEXING AND SELF-TEST WRAPAROUND LOGIC OUT
RTA(4:0) REMOTE TERMINAL ADDRESS
CONTROL INPUTS
STATUS OUTPUTS DECODER COMMAND RECOGNITION CONTROL AND ERROR LOGIC 1K X 16 RAM ADDR(9:0) MUX ENCODER PTR REGISTER
IN OUT
DECODER
IN
12MHz DATA(15:0) 2MHz RESET
Figure 1. UT1553B RTR Functional Block Diagram
RTR-1
Table of Contents
1.0 ARCHITECTURE AND OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.1 Memory Map and Host Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.2 RTR RAM Pointer Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.3 Internal Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 1.4 Mode Code and Subaddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.5 MIL-STD-1553B Subaddress and Mode Codes . . . . . . . . . . . . . . . . . . . . . . . . .9 1.6 Terminal Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.7 Internal Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.8 Power-up and Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.9 Encoder and Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.10 RT-RT Transfer Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.11 Illegal Command Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MEMORY MAP EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.0
3.0
PIN IDENTIFICATION AND DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.0
MAXIMUM AND RECOMMENDED OPERATING CONDITIONS. . . . . . . . . . . . . . . . . 19
5.0
DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.0
AC ELECTRICAL CHARACTERISTICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.0
PACKAGE OUTLINE DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
RTR-2
1.0 ARCHITECTURE AND OPERATION
The UT1553B RTR is an interface device linking a MILSTD-1553 serial data bus and a host microprocessor system. The RTR's MIL-STD-1553B interface includes encoding/ decoding logic, error detection, command recognition, 1K x 16 of SRAM, pointer registers, clock, and reset circuits.
alert the host. The RBUSY signal is programmable via the internal Control Register to be asserted either 5.7ms or 2.7ms prior to the RTR needing access to its internal RAM. The RTR stores MIL-STD-1553B messages in 1K x 16 of on-chip RAM. For efficient use of the 1K x 16 memory on the RTR, the host programs a set of pointers to map where the 1553B message is stored. The RTR uses the upper 64 words (address 3C0 (hex) through 3FF (hex)) as pointers. The RTR provides pointers for all 30 receive subaddresses, all 30 transmit subaddresses, and four mode code commands with associated data words as defined in MILSTD-1553B. The remaining 960 words of memory contain receive, transmit, and mode code data in a host-defined structure.
1.1 Memory Map and Host Memory Interface The host can access the 1K x 16 RAM memory like a standard RAM device through the 10-bit address and 16-bit data buses. The host uses the Chip Select (CS), Read/Write (RD/WR), and Output Enable (OE) signals to control data transfer to and from memory. When the RTR requires access to its own internal RAM, it asserts the RBUSY signal to
RTR Memory Map Message Storage Locations 000 (hex)
3BF(hex) 15 MSB XMIT VECTOR WORD MODE CODE (W/DATA) Receive Message Pointers (3C1 TO 3DE) RCV SUBADDRESS 30 SYNCHRONIZE MODE CODE (W/DATA) 15 MSB 0 LSB 3DE (hex) 3DF (hex) RCV SUBADDRESS 01 0 LSB
3C0 (hex) 3C1 (hex)
Transmit Message Pointers (3E1 TO 3FE)
XMIT LAST COMMAND MODE CODE (W/DATA) XMT SUBADDRESS 01
3E0 (hex) 3E1 (hex)
XMT SUBADDRESS 30 XMT BIT WORD MODE CODE (W/DATA) 15 MSB Figure 2. RTR Memory Map 0 LSB
3FE (hex) 3FF (hex)
RTR-3
MESSAGE INDEX 15 (MSB) Message index: Defines the maximum messages buffered for the given subaddresses.
10 9
MESSAGE DATA ADDRESSES
0 (LSB)
Message Data Address: Indicates the starting memory address for incoming message storage. Figure 3. Message Pointer Structure
1.2 RTR RAM Pointer Structure The RAM 16-bit pointers have a 6-bit index field and a 10-bit address field. The 6-bit index field allows for the storage of up to 64 messages per subaddress. A message consists of the 1553 command word and its associated data words.
The 16-bit pointer for Transmit Last Command Mode Code is located at memory location 3E0 (hex). The Transmit Last Command Mode Code pointer buffers up to 63 command words. An example of command word storage follows:
Example: 3E0 (hex) Contents = FC00 (hex) 11 1111 00 0000 0000 Address Field = 000 (hex) Index Field = 3F (hex) First command word storage location (3E0=F801): Address Field = 001 (hex) Index Field = 3E (hex) Sixty-third command word storage location (3E0=003F): Address Field = 03F (hex) Index Field = 00 (hex) Sixty-fourth command word storage location (3E0=003F) (previous command word overwritten):
Address Field = 03F (hex) Index Field = 00 (hex)
The Transmit Last Command Mode Code has Address Field boundary conditions for the location of command word buffers. The host can allocate a maximum 63 sequential locations following the Address Field starting address. For proper operation, the Address Field must start on an I x 40 (hex) address boundary, where I is greater than or equal to zero and less than or equal to 14. A list of valid Index and Address Fields follows:
I 0 1 2 3 4 5 6 7 8 9 Valid Index Fields 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) 3F (hex) to 00 (hex) Valid Address Fields 000 (hex) to 03F (hex) 040 (hex) to 07F (hex) 080 (hex) to 0BF (hex) 0C0 (hex) to 0FF (hex) 100 (hex) to 13F (hex) 140 (hex) to 17F (hex) 180 (hex) to 1BF (hex) 1C0 (hex) to 1FF (hex) 200 (hex) to 23F (hex) 240 (hex) to 27F (hex) 280 (hex) to 2BF (hex) 2C0 (hex) to 2FF (hex 300 (hex) to 33F (hex) 340 (hex) to 37F (hex) 380 (hex) to 3BF (hex)
10 3F (hex) to 00 (hex) 11 3F (hex) to 00 (hex) 12 3F (hex) to 00 (hex) 13 3F (hex) to 00 (hex) 14 3F (hex) to 00 (hex)
RTR-4
Subaddress/Mode Code
RAM Location
Subaddress/Mode Code
RAM Location
Transmit Vector Word Mode Code Receive Subaddress 01 Receive Subaddress 02 Receive Subaddress 03 Receive Subaddress 04 Receive Subaddress 05 Receive Subaddress 06 Receive Subaddress 07 Receive Subaddress 08 Receive Subaddress 09 Receive Subaddress 10 Receive Subaddress 11 Receive Subaddress 12 Receive Subaddress 13 Receive Subaddress 14 Receive Subaddress 15 Receive Subaddress 16 Receive Subaddress 17 Receive Subaddress 18 Receive Subaddress 19 Receive Subaddress 20 Receive Subaddress 21 Receive Subaddress 22 Receive Subaddress 23 Receive Subaddress 24 Receive Subaddress 25 Receive Subaddress 26 Receive Subaddress 27 Receive Subaddress 28 Receive Subaddress 29 Receive Subaddress 30 Synchronize w/Data Word Mode Code
3C0 (hex) 3C1 (hex) 3C2 (hex) 3C3 (hex) 3C4 (hex) 3C5 (hex) 3C6 (hex) 3C7 (hex) 3C8 (hex) 3C9 (hex) 3CA (hex) 3CB (hex) 3CC (hex) 3CD (hex) 3CE (hex) 3CF (hex) 3D0 (hex) 3D1 (hex) 3D2 (hex) 3D3 (hex) 3D4 (hex) 3D5 (hex) 3D6 (hex) 3D7 (hex) 3D8 (hex) 3D9 (hex) 3DA (hex) 3DB (hex) 3DC (hex) 3DD (hex) 3DE (hex) 3DF (hex)
Transmit Last Command Mode Code Transmit Subaddress 01 Transmit Subaddress 02 Transmit Subaddress 03 Transmit Subaddress 04 Transmit Subaddress 05 Transmit Subaddress 06 Transmit Subaddress 07 Transmit Subaddress 08 Transmit Subaddress 09 Transmit Subaddress 10 Transmit Subaddress 11 Transmit Subaddress 12 Transmit Subaddress 13 Transmit Subaddress 14 Transmit Subaddress 15 Transmit Subaddress 16 Transmit Subaddress 17 Transmit Subaddress 18 Transmit Subaddress 19 Transmit Subaddress 20 Transmit Subaddress 21 Transmit Subaddress 22 Transmit Subaddress 23 Transmit Subaddress 24 Transmit Subaddress 25 Transmit Subaddress 26 Transmit Subaddress 27 Transmit Subaddress 28 Transmit Subaddress 29 Transmit Subaddress 30 Transmit Bit Word Mode Code
3E0 (hex) 3E1 (hex) 3E2 (hex) 3E3 (hex) 3E4 (hex) 3E5 (hex) 3E6 (hex) 3E7 (hex) 3E8 (hex) 3E9 (hex) 3EA (hex) 3EB (hex) 3EC (hex) 3ED (hex) 3EE (hex) 3EF (hex) 3F0 (hex) 3F1 (hex) 3F2 (hex) 3F3 (hex) 3F4 (hex) 3F5 (hex) 3F6 (hex) 3F7 (hex) 3F8 (hex) 3F9 (hex) 3FA (hex) 3FB (hex) 3FC (hex) 3FD (hex) 3FE (hex) 3FF (hex)
1.3 Internal Registers The RTR uses two internal registers to allow the host to control the RTR operation and monitor its status. The host uses the Control (CTRL) signal along with Chip Select (CS), Read/Write (RD/WR), and Output Enable (OE) to read the 16-bit Status Register or write to the 11-bit Control Register. No address data is needed to select a register.
The Control Register toggles bits in the MIL-STD-1553B status word, enables the biphase inputs, recognizes broadcast commands, determines RAM Busy (RBUSY) timing, selects terminal active flag, and puts the part in selftest mode. The Status Register supplies operational status of the UT1553B RTR to the host. These registers must be initialized before attempting RTR operation. Internal registers can be accessed while RBUSY is active.
RTR-5
Control Register (Write Only) The 11-bit write-only Control Register manages the operation of the RTR. Write to the Control Register by applying a logic one to OE, and a logic zero to CTRL, CS, and RD/WR. Data is loaded into the Control Register via I/O pins DATA(12:0). Control register write must occur 50ns before the rising edge of COMSTR to latch data into outgoing status word.
Bit Number Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 Initial Condition [1] [1] [0] [1] [0] [0] [0] [0] [0] [1] [X] [X] [1] Description Channel A Enable. A logic 1 enables Channel A biphase inputs. Channel B Enable. A logic 1 enables Channel B biphase inputs. Terminal Flag. A logic 1 sets the Terminal Flag bit of the Status Word. System Busy. A logic 1 sets the Busy bit of the Status Word and limits RTR access to the memory. No data words can be retrieved or stored; command words will be stored. Subsystem Busy. A logic 1 sets the Subsystem Flag bit of the Status Word. Self-Test Channel Select. This bit selects which channel the self-test checks; a logic 1 selects Channel A and a logic 0 selects Channel B. Self-Test Enable. A logic 1 places the RTR in the internal self-test mode and inhibits normal operation. Channels A and B should be disabled if self-test is chosen. Service Request. A logic 1 sets the Service Request bit of the Status Word. Instrumentation. A logic 1 sets the Instrumentation bit of the Status Word. Broadcast Enable. A logic 1 enables the RTR to recognize broadcast commands. Don't care. Don't care. RBUSY Time Select. A logic 1 selects a 5.7s RBUSY alert; a logic 0 selects a 2.7s RBUSY alert.
[] - Values in parentheses indicate the initialized values of these bits.
CONTROL REGISTER (WRITE ONLY):
X X X RBUSY TS [1] X X BCEN [1] INS [0] SRQ [0] ITST [0] ITCS [0] SUBS BUSY [0] [1] TF [0] CH B EN [1] CH A EN [1]
MSB [ ] defines reset state X don't care
LSB
Figure 4a. Control Register
RTR-6
Status Register (Read Only)
The 16-bit read-only Status Register provides the RTR system status. Read the Status Register by applying a logic 0 to CTRL, CS, and OE, and a logic 1 to RD/WR. The 16-bit contents of the Status Register are read from data I/O pins DATA(15:0).
Bit Number Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Initial Condition [0] [0] [0] [0] [0] [0]
Description MCSA0. The LSB of the mode code or subaddress as indicated by the logic state of bit 5. MCSA1. Mode code or subaddress as indicated by the logic state of bit 5. MCSA2. Mode code or subaddress as indicated by the logic state of bit 5. MCSA3. Mode code or subaddress as indicated by the logic state of bit 5. MCSA4. Mode code or subaddress as indicated by the logic state of bit 5. MC/SA. A logic 1 indicates that bits 4 through 0 are the subaddress of the transmit or receive command. A logic 0 indicates that bits 4 through 0 are a mode code, and that the last command was a mode command. Channel A/B. A logic 1 indicates that the most recent command arrived on Channel A; a logic 0 indicates that it arrived on Channel B. Channel B Enabled. A logic 1 indicates that Channel B is available for both Channel A Enabled. A logic 1 indicates that Channel A is available for both reception and transmission. Terminal Flag Enabled. A logic 1 indicates that the Bus Controller has not Bus Controller, via the above mode code, is overriding the host system's ability to set the Terminal Flag bit of the status word. Busy. A logic 1 indicates the Busy bit is set. This bit is reset when the System Busy bit in the Control Register is reset. Self-Test. A logic 1 indicates that the chip is in the internal self-test mode. TA Parity Error. A logic 1 indicates the wrong Terminal Address parity; it Error bit being set to a logic one, and Channels A and B become disabled. Message Error. A logic 1 indicates that a message error has occurred since has been examined. Message error condition must be removed before reading the Status Register to reset the Message Error bit. Valid Message. A logic 1 indicates that a valid message has been received Terminal Active. A logic 1 indicates the device is executing a transmit or
Bit 6 Bit 7 Bit 8 Bit 9
[1] [1] [1] [1]
Bit 10 Bit 11 Bit 12 Bit 13
[1] [0] [0] [0]
Bit 14 Bit 15
[0] [0]
[] - Values in parentheses indicate the initialized values of these bits.
STATUS REGISTER (READ ONLY):
TERM VAL MESS TAPA SELF BUSY TFEN CH A CH B CHNL MC/ MCSA MCSA MCSA MCSA MCSA ACTV MESS ERR ERR TEST EN EN A/B SA 4 3 2 1 0 [0] [0] [0] [0] [0] [1] [1] [1] [1] [1] [0] [0] [0] [0] [0] [0] LSB MSB
[] defines reset state Figure 4b. Status Register
RTR-7
1.4 Mode Code and Subaddress The UT1553B RTR provides subaddress and mode code decoding meeting MIL-STD-1553B. In addition, the device has automatic internal illegal command decoding for reserved MIL-STD-1553B mode codes. Upon command word validation and decode, status pins MCSA(4:0) and MC/SA become valid. Status pin MC/SA will indicate whether the data on pins MCSA(4:0) is mode code or subaddress information. Status Register bits 0 through 5
contain the same information as pins MCSA(4:0) and MC/ SA. The system designer can use signals MCSA(4:0), MC/SA, BRDCST, RTRT, etc. to illegalize mode codes, subaddresses, and other message formats (broadcast and RT-to-RT) via the Illegal Command (ILLCOM) input to the part (see figure 21 on page 31).
RTR MODE CODE HANDLING PROCEDURE
T/R Mode Code Function Operation
0
10100
Selected Transmitter Shutdown 2
0
10101
Override Selected Transmitter Shutdown 2
0 1
10001 00000
Synchronize (w/Data) Dynamic Bus Control 2
1 1 1 1 1 1 1
00001 00010 00011 00100 00101 00110 00111
Synchronize 1 Transmit Status Word 3 Initiate Self-Test 1 Transmitter Shutdown Override Transmitter Shutdown Inhibit Terminal Flag Bit Override Inhibit Terminal Flag
1 1 1 1
01000 10010 10000 10011
Reset Remote Terminal 1 Transmit Last Command Word3 Transmit Vector Word Transmit BIT Word
1. Command word stored 2. MERR pin asserted 3. MERR bit set in Status Register 4. Status word transmitted 1. Command word stored 2. MERR pin asserted 3. MERR bit set in Status Register 4. Status word transmitted 1. Command word stored 2. Data word stored 3. Status word transmitted 1. Command word stored 2. MERR pin asserted 3. MERR bit set in Status Register 4. Status word transmitted 1. Command word stored 2. Status word transmitted 1. Command word stored 2. Status word transmitted 1. Command word stored 2. Status word transmitted 1. Command word stored 2. Alternate bus shutdown 3. Status word transmitted 1. Command word stored 2. Alternate bus enabled 3. Status word transmitted 1. Command word stored 2. Terminal Flag bit set to zero and disabled 3. Status word transmitted 1. Command word stored 2. Terminal Flag bit enabled, but not set to logic one 3. Status word transmitted 1. Command word stored 2. Status word transmitted 1. Command word transmitted 2. Last command word transmitted 1. Command word stored 2. Status word transmitted 3. Data word transmitted 1. Command word stored 2. Status word transmitted 3. Data word transmitted
Notes: 1. Further host interaction required for mode code operation 2. Reserved mode code; A) MERR pin asserted, B) MESS ERR bit set, C) status word transmitted (ME bit set to logic one). 3. Status word not affected. 4. Undefined mode codes are treated as reserved mode codes.
RTR-8
1.5 MIL-STD-1553B Subaddress and Mode Code Definitions
Table 1: Subaddress and Mode Code Definitions Per MIL-STD-1553B
Subaddress Field Binary (Decimal) 00000 (00) 00001 (01) 00010 (02) 00011 (03) 00100 (04) 00101 (05) 00110 (06) 00111 (07) 01000 (08) 01001 (09) 01010 (10) 01011 (11) 01100 (12) 01101 (13) 01110 (14) 01111 (15) 10000 (16) 10001 (17) 10010 (18) 10011 (19) 10100 (20) 10101 (21) 10110 (22) 10111 (23) 11000 (24) 11001 (25 11010 (26) 11011 (27) 11100 (28) 11101 (29) 11110 (30) 11111 (31)
1
Message Format Receive
1
Transmit User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined
1
Description Mode Code Indicator
User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined User Defined
1
Mode Code Indicator
Notes: 1. Refer to mode code assignments per MIL-STD-1553B
1.6 Terminal Address The Terminal Address of the RTR is programmed via five input pins: RTA(4:0) and RTPTY. Asserting MRST latches the RTR's Terminal Address from pins RTA(4:0) and parity bit RTPTY. The address and parity cannot change until the next assertion of the MRST. The parity of the Terminal Address is odd; input pin RTPTY is set to a logic state to satisfy this requirement. A logic 1 on Status Register bit 12
indicates incorrect Terminal Address parity. An example follows:
RTA(4:0) = 05 (hex) = 00101 RTPTY = 1 (hex) = 1 Sum of 1's = 3 (odd), Status Register bit 12 = 0 RTA(4:0) = 04 (hex) = 00100 RTPTY = 0 (hex) = 0 Sum of 1's = 1 (odd), Status Register bit 12 = 0
RTR-9
RTA(4:0) = 04 (hex) = 00100 RTPTY = 1 (hex) = 1 Sum of 1's = 2 (even), Status Register bit 12 = 1
The RTR checks the Terminal Address and parity on Master Reset. With Broadcast disabled, RTA (4:0) = 11111 operates as a normal RT address.
power-up if the terminal address parity (odd) is incorrect, the biphase inputs are disabled and the message error pin (MERR) is asserted. This condition can also be monitored via bit 12 of the Status Register. The MERR pin is negated on reception of first valid command.
1.7 Internal Self-Test Setting bit 6 of the Control Register to a logic one enables the internal self-test. Disable Channels A and B at this time to prevent bus activity during self-test by setting bits 0 and 1 of the Control Register to a logic zero. Normal operation is inhibited when internal self-test is enabled. The self-test capability of the RTR is based on the fact that the MIL-STD1553B status word sync pulse is identical to the command word sync pulse. Thus, if the status word from the encoder is fed back to the decoder, the RTR will recognize the incoming status word as a command word and thus cause the RTR to transmit another status word. After the host invokes self-test, the RTR self-test logic forces a status word transmission even though the RTR has not received a valid command. The status word is sent to decoder A or B depending on the channel the host selected for self-test. The self-test is controlled by the host periodically changing the bit patterns in the status word being transmitted. Writing to the Control Register bits 2, 3, 4, 7, and 8 changes the status word. Monitor the self-test by sampling either the Status Register or the external status pins (i.e., Command Strobe (COMSTR), Transmit/Receive (T/R)). For more detailed explanation of internal self-test, consult UTMC publication RTR/RTS Internal Self-Test Routine. 1.8 Power-up and Master Reset After power-up, reset initializes the part with its biphase ports enabled, latches the Terminal Address, and turns on the busy option. The device is ready to accept commands from the MIL-STD-1553B bus. The busy flag is asserted while the host is loading the message pointers and messages. After this task is completed, the host removes the busy condition via a Control Register write to the RTR. On
1.9 Encoder and Decoder The RTR interfaces directly to a bus transmitter/ receiver via the RTR Manchester II encoder/decoder. The UT1553B RTR receives the command word from the MIL-STD1553B bus and processes it either by the primary or secondary decoder. Each decoder checks for the proper sync pulse and Manchester waveform, edge skew, correct number of bits, and parity. If the command is a receive command, the RTR processes each incoming data word for correct format and checks the control logic for correct word count and contiguous data. If an invalid message error is detected, the message error pin is asserted, the RTR ceases processing the remainder (if any) of the message, and it then suppresses status word transmission. Upon command validation recognition, the external status outputs are enabled. Reception of illegal commands does not suppress status word transmission.
The RTR automatically compares the transmitted word (encoder word) to the reflected decoder word by way of the continuous loop-back feature. If the encoder word and reflected word do not match, the transmitter error pin (TXERR) is asserted. In addition to the loop-back compare test, a timer precludes a transmission greater than 760s by the assertion of Fail-safe Timer (TIMERON). This timer is reset upon receipt of another command.
1.10 RT-RT Transfer Compare The RT-to-RT Terminal Address compare logic makes sure that the incoming status word's Terminal Address matches the Terminal Address of the transmitting RT specified in the command word. An incorrect match results in setting the Message Error bit and suppressing transmission of the status word. (RT-to-RT transfer time-out = 54s)
RTR-10
1.11 Illegal Command Decoding The host has the option of asserting the ILLCOM pin to illegalize a received command word. On receipt of an illegal command, the RTR sets the Message Error bit in the status word, sets the message error output, and sets the message error latch in the Status Register.
The following RTR outputs may be used to externally decode an illegal command, Mode Code or Subaddress indicator (MC/SA), Mode Code or Subaddress bus MCSA(4:0), Command Strobe (COMSTR), Broadcast (BRDCST), and Remote Terminal to Remote Terminal transfer (RTRT) (see figure 21 on page 31). To illegalize a transmit command, the ILLCOM pin must be asserted within 3.3s after VALMSG goes to a logic 1 if the RTR is to respond with the Message Error bit of the status word at a logic 1. If the illegal command is mode code 2, 4, 5, 6, 7, or 18, the ILLCOM pin must be asserted within 664ns after Command Strobe (COMSTR) transitions to logic 0. Asserting the ILLCOM pin within the 664ns inhibits the mode code function. For mode code illegalization, assert the ILLCOM pin until the VALMSG signal is asserted. For an illegal receive command, the ILLCOM pin is asserted within 18.2s after the COMSTR transitions to a logic 0 in order to suppress data words from being stored. In addition, the ILLCOM pin must be at a logic 1 throughout the reception of the message until VALMSG is asserted. This does not apply to illegal transmit commands since the status word is transmitted first. The above timing conditions also apply when the host externally decodes an illegal broadcast command. The host must remove the illegal command condition so that the next command is not falsely decoded as illegal.
2.0 MEMORY MAP EXAMPLE
Figures 5 and 6 illustrate the UT1553B RTR buffering three receive command messages to Subaddress 4. The receive message pointer for Subaddress 4 is located at 03C4 (hex) in the 1K x 16 RAM. The 16-bit contents of location 03C4 (hex) point to the memory location where the first receive message is stored. The Address Field defined as bits 0 through 9 of address 03C4 (hex) contain address information. The Index Field defined as bits 10 through 15 of address 03C4 (hex) contain the message buffer index (i.e., number of messages buffered). Figure 5 demonstrates the updating of the message pointer as each message is received and stored. The memory storage of these three messages is shown in figure 6. After receiving the third message for Subaddress 4 (i.e., Index Field equals zero) the Address Field of the message pointer is not incremented. If the host does not update the receive message pointer for Subaddress 4 before the next receive command for Subaddress 4 is accepted, the third message will be overwritten. Figures 7 and 8 show an example of multiple message retrieval from Subaddress 16 upon reception of a MIL-STD1553B transmit command. The message pointer for transmit Subaddress 16 is located at 03F0 (hex) in the 1K x 16 RAM. The 16-bit contents of location 03F0 (hex) point to the memory location where the first message data words are stored. Figure 7 demonstrates the updating of the message pointer as each message is received and stored. The data memory for these three messages is shown in figure 8.
RTR-11
Example: Remote terminal will receive and buffer three MIL-STD-1553 receive commands of various word lengths to Subaddress 4. MIL-STD-1553 Bus Activity: CMD WORD #1 DW0 DW1 DW2 DW3 SA = 4 CMD WORD #2 DW0 DW1 T/R = 0 SA = 4 WC = 4 CMD WORD #3 DW0 DW1 DW2 DW3 T/R = 0 SA = 4 WC = 2 T/R = 0 WC = 4 Receive Subaddress 4; INDEX= 0000 10 03C4 (hex) 0840 (hex) data pointer at 03C4 ADDRESS= 00 0100 0000 (hex). (Initial condition) After message #1, INDEX= 0000 01 03C4 (hex) 0445 (hex) 4 data words plus ADDRESS= 00 0100 0101 command word. After message #2, INDEX= 0000 00 03C4 (hex) 0048 (hex) 2 data words plus ADDRESS= 00 0100 1000 command word. After message #3, INDEX= 0000 00 03C4 (hex) 0048 (hex) 4 data words plus ADDRESS= 00 0100 1000 command word. Figure 5. RTR Message Handling
03C4 (hex)
0840 (hex)
COMMAND WORD #1 DATA WORD 0 DATA WORD 1 DATA WORD 2 DATA WORD 3
040 (hex) 041 (hex) 042 (hex) 043 (hex) 044 (hex) 045 (hex) 046 (hex) 047 (hex) 048 (hex) 049 (hex) 04A (hex) 04B (hex) 04C (hex)
03C4 (hex)
0445 (hex)
COMMAND WORD #2 DATA WORD 0 DATA WORD 1
03C4 (hex)
0048 (hex)
COMMAND WORD #3 DATA WORD 0 DATA WORD 1 DATA WORD 2
03C4 (hex)
0048 (hex)
DATA WORD 3
Figure 6. Memory Storage Subaddress 4
RTR-12
Example: Remote terminal will transmit and buffer three MIL-STD-1553 transmit commands of various word lengths to Subaddress 16. MIL-STD-1553 Bus Activity: CMD WORD #1 SW DW0 DW1 DW2 DW3 SA= 16 CMD WORD #2 SW DW0 DW1 T/R=1 WC= 4 SA= 16 CMD WORD #3 SW DW0 DW1 DW2 DW3 T/R=1 WC= 2 SA= 16 T/R=1 WC= 4 Transmit Subaddress 16; data pointer at 03F0 (hex). (Initial condition) After message #1, 4 data words. After message #2, 2 data words. After message #3, 4 data words. 03F0 (hex) 0830 (hex) INDEX= 0000 10 ADDRESS= 00 0011 0000 INDEX= 0000 01 ADDRESS= 00 0011 0100 INDEX= 0000 00 ADDRESS= 00 0011 0110 INDEX= 0000 00 ADDRESS= 00 0011 0110
03F0 (hex) 03F0 (hex) 03F0 (hex)
0434 (hex) 0036 (hex) 0036 (hex)
Figure 7. RTR Message Handling
0830 (hex)
DATA WORD 0 DATA WORD 1 DATA WORD 2 DATA WORD 3
030 (hex) 031 (hex) 032 (hex) 033 (hex) 034 (hex) 035 (hex) 036 (hex) 037 (hex) 038 (hex) 039 (hex)
0434 (hex)
DATA WORD 0 DATA WORD 1
0036 (hex)
DATA WORD 0 DATA WORD 1 DATA WORD 2
0036 (hex) 034 (hex)
DATA WORD 3
Note: The example is valid only if message structure is known in advance.
Figure 8. Memory Storage Subaddress 16
RTR-13
3.0 PIN IDENTIFICATION AND DESCRIPTION
BIPHASE OUT TAZ TAO TBZ TBO BIPHASE IN RAZ RAO RBZ RBO TERMINAL ADDRESS RTA0 RTA1 RTA2 RTA3 RTA4 RTPTY MODE/CODE SUBADDRESS MCSA0 MCSA1 MCSA2 MCSA3 STATUS SIGNALS MCSA4 MERR TERACT TXERR TIMERON COMSTR MC/SA BRDCST T/R RTRT VALMSG RBUSY CONTROL SIGNALS CS RD/WR CTRL OE ILLCOM
A10 B10 A9 B9 L7 K8 L6 K7 L5 K5 L4 K4 L3 K6 B2 A2 A3 B3 A4 A5 A6 B5 B6 B8 B1 A7 B4 B7 L8 C2 K2 K1 J1 L9 K9
J2 H1 H2 G1 G2 F1 E2 D1 D2 C1 L10 K10 K11 J10 J11 H10 H11 G10 F11 E10 E11 D10 D11 C10 C11 B11 F10 E1 F2 G11 L2 A8 K3
ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 VDD VDD VSS VSS 12MHZ 2MHZ MRST
ADDRESS BUS ADDR(9:0)
DATA BUS DATA(15:0)
UT1553B RTR
POWER GROUND
CLOCK
RES
E
Figure 9. UT1553B RTR Pin Description
RTR-14
Legend for TYPE and ACTIVE fields: TI = TTL input TUI = TTL input (pull-up) TDI = TTL input (pull-down) TO = TTL output
TTO = Three-state TTL output TTB = Three-state TTL bidirectional AL = Active low AH = Active high [] - Value in parentheses indicates initial state of pins.
DATA BUS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
B11 C11 C10 D11 D10 E11 E10 F11 G10 H11 H10 J11 J10 K11 K10 L10
TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB TTB
-----------------
Bit 15 (MSB) of the bidirectional Data bus. Bit 14 of the bidirectional Data bus. Bit 13 of the bidirectional Data bus. Bit 12 of the bidirectional Data bus. Bit 11 of the bidirectional Data bus. Bit 10 of the bidirectional Data bus. Bit 9 of the bidirectional Data bus. Bit 8 of the bidirectional Data bus. Bit 7 of the bidirectional Data bus. Bit 6 of the bidirectional Data bus. Bit 5 of the bidirectional Data bus. Bit 4 of the bidirectional Data bus. Bit 3 of the bidirectional Data bus. Bit 2 of the bidirectional Data bus. Bit 1 of the bidirectional Data bus. Bit 0 (LSB) of the bidirectional Data bus.
ADDRESS BUS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
ADDR9 ADDR8 ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0
C1 D2 D1 E2 F1 G2 G1 H2 H1 J2
TI TI TI TI TI TI TI TI TI TI
-----------
Bit 9 (MSB) of the Address bus. Bit 8 of the Address bus. Bit 7 of the Address bus. Bit 6 of the Address bus. Bit 5 of the Address bus. Bit 4 of the Address bus. Bit 3 of the Address bus. Bit 2 of the Address bus. Bit 1 of the Address bus. Bit 0 (LSB) of the Address bus.
RTR-15
CONTROL INPUTS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
CS
K2
TI
AL
Chip Select. The host processor uses the CS signal for RTR Status Register reads, Control Register writes, or host access to the RTR internal RAM. Read/Write. The host processor uses a high level on this input in conjunction with CS to read the RTR Status Register or the RTR internal RAM. A low level on this input is used in conjunction with CS to write to the RTR Control Register or the RTR internal RAM. Control. The host processor uses the active low CTRL input signal in conjunction with CS and RD/WR to access the RTR registers. A high level on this input means access is to RTR internal RAM only. Output Enable. The active low OE signal is used to control the direction of data flow from the RTR. For OE = 1, the RTR Data bus is three-state; for OE = 0, the RTR Data bus is active. Illegal Command. The host processor uses the ILLCOM input to inform the RTR that the present command is illegal.
RD/WR
K1
TI
--
CTRL
J1
TI
AL
OE
L9
TI
AL
ILLCOM
K9
TDI
AH
STATUS INPUTS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
MERR [0]
A5
TO
AH
Message Error. The active high MERR output signals that the Message Error bit in the Status Register has been set due to receipt of an illegal command, or an error during message sequence. MERR will reset to logic zero on the receipt of the next valid command. Transmission Error. The active high TXERR output is asserted when the RTR detects an error in the reflected word versus the transmitted word, using the continuous loop-back compare feature. Reset on next COMSTR assertion. Fail-safe Timer. The TIMERON output pulses low for 760s when the RTR begins transmitting (i.e., rising edge of VALMSG) to provide a fail-safe timer meeting the requirements of MIL-STD-1553B. This pulse is reset when COMSTR goes low or during a Master Reset. Command Strobe. COMSTR is an active low output of 500ns duration identifying receipt of a valid command. Terminal Active. The active low TERACT output is asserted at the beginning of the RTR access to internal RAM for a given command and negated after the last access for that command.
TXERR [0]
B5
TO
AH
TIMERON [1]
B6
TO
AL
COMSTR [1] TERACT
B8 A6
TO TO
AL AL
RTR-16
STATUS INPUTS Continued from page 16.
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
BRDCST [1] T/R [0]
A7 B4
TO
AL
Broadcast. BRDCST is an active low output that identifies receipt of a valid broadcast command. Transmit/Receive. A high level on this pin indicates a transmit command message transfer is being or was processed, while a low level indicates a receive command message transfer is being or was processed. Valid Message. VALMSG is an active high output indicating a valid message (including Broadcast) has been received. VALMSG goes high prior to transmitting the 1553 status word and is reset upon receipt of the next command. RTR Busy. RBUSY is asserted high while the RTR is accessing its own internal RAM either to read or update the pointers or to store or retrieve data words. RBUSY becomes active either 2.7s or 5.7s before RTR requires RAM access. This timing is controlled by Control Register bit 12 (see section 1.3).
TO
--
RTRT [1]
B7
TO
AH
RBUSY [0]
C2
TO
AH
MODE CODE/SUBADDRESS OUTPUTS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
MC/SA [0]
B1
TO
--
Mode Code/Subaddress Indicator. If MC/SA is low, it indicates that the most recent command word is a mode code command. If MC/SA is high, it indicates that the most recent command word is for a subaddress. This output indicates whether the mode code/subaddress ouputs (i.e., MCSA(4:0)) contain mode code or subaddress information. Mode Code/Subaddress Output 0. If MC/SA is low, this pin represents the least significant bit of the most recent command word (the LSB of the mode code). If MC/SA is high, this pin represents the LSB of the subaddress. Mode Code/Subaddress Output 1. Mode Code/Subaddress Output 2. Mode Code/Subaddress Output 3. Mode Code/Subaddress Output 4. If MC/SA is low, this pin represents the most significant bit of the mode code. If MC/SA is high, this pin represents the MSB of the subaddress.
MCSA0 [0]
B2
TO
--
MCSA1 [0] MCSA2 [0] MCSA3 [0] MCSA4 [0]
A2 A3 B3 A4
TO TO TO TO
-----
RTR-17
REMOTE TERMINAL ADDRESS INPUTS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
RTA4 RTA3 RTA2 RTA1 RTA0 RTPTY 1
L3 K4 L4 K5 L5 K6
TUI TUI TUI TUI TUI TUI
-------
Remote Terminal Address bit 4 (MSB). Remote Terminal Address bit 3. Remote Terminal Address bit 2. Remote Terminal Address bit 1. Remote Terminal Address bit 0 (LSB). Remote Terminal Address Parity. This input must provide odd parity for the Remote Terminal Address.
BIPHASE INPUTS
NAME
PIN NUMBER (PGA)
TYPE
ACTIVE
DESCRIPTION
RAZ RAO RBZ RBO
L7 K8 L6 K7
TI TI TI TI
-----
Receiver - Channel A, Zero Input. Idle low Manchester input form the 1553 bus receiver. Receiver - Channel A, One Input. This input is the complement of RAZ. Receiver - Channel B, Zero Input. Idle low Manchester input from the 1553 bus receiver. Receiver - Channel B, One Input. This input is the complement of RBZ.
Note: 1. For uniphase operation, tie RAZ (or RBZ) to VDD and apply true uniphase input signal to RAO (or RBO).
BIPHASE OUTPUTS
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
TAZ [0] TAO [0] TBZ [0] TBO [0]
A10
TO
--
Transmitter - Channel A, Zero Output. This idle low Manchester encoded data output is connected to the 1553 bus transmitter input. The output is idle low. Transmitter - Channel A, One Output. This output is the complement of TAZ. The output is idle low. Transmitter - Channel B, Zero Output. This idle low Manchester encoded data output is connected to the 1553 bus transmitter input. The output is idle low. Transmitter - Channel B, One Output. This input is the complement of TBZ. The output is idle low.
B10 A9
TO TO
---
B9
TO
--
RTR-18
MASTER RESET AND CLOCK
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
MRST
K3
TUI
--
Master Reset. Initializes all internal functions of the RTR. MRST must be asserted 500ns before normal RTR operation (500ns minimum). Does not reset RAM. 12 MHz Input Clock. This is the RTR system clock that requires an accuracy greater than 0.01% with a duty cycle of 50% 10%. 2MHz Clock Output. This is a 2MHz clock output generated by the 12MHz input clock. This clock is stopped when MRST is low.
12MHz
L2
TI
--
2MHz
A8
TO
--
POWER AND GROUND
NAME PIN NUMBER (PGA) TYPE ACTIVE DESCRIPTION
VDD VSS
F10 E1 F2 G11
PWR PWR GND GND
-----
+5 VDC Power. Power supply must be +5 VDC 10%. Reference ground. Zero VDC logic ground.
4.0 OPERATING CONDITIONS
ABSOLUTE MAXIMUM RATINGS* (referenced to VSS)
SYMBOL
VDD VIO II TSTG PD TJ JC
PARAMETER DC supply voltage
LIMITS -0.3 to +7.0
UNIT
V V mA C mW C C/W
Voltage on any pin DC input current Storage temperature Maximum power dissipation Maximum junction temperature Thermal resistance, junction-to-case
1
0.3 to VDD+0.3 10 -65 to +150 300 +175 20
Note: 1. Does not reflect the added PD due to an output short-circuited. * Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
VDD VIN TC FO
PARAMETER DC supply voltage
LIMITS 4.5 to 5.5
UNIT
V V C MHz
DC input voltage Temperature range Operating frequency
0 to VDD -55 to +125 12 .01%
RTR-19
5.0 DC ELECTRICAL CHARACTERISTICS
(VDD = 5.0V 10%; -55C < TC < +125C)
SYMBOL PARAMETER CONDITION MINIMUM MAXIMUM UNIT
VIL VIH IIN
Low-level input voltage High-level input voltage Input leakage current TTL inputs Inputs with pull-down resistors Inputs with pull-up resistors Low-level output voltage High-level output voltage Three-state output leakage current Short-circuit output current 1, 2 Input capacitance 3 Output capacitance Bidirect I/O capacitance 3 Average operating current 1, 4 Quiescent current
3
0.8 2.0 VIN = VDD or VSS VIN = VDD VIN = VSS IOL = 3.2mA IOH = -400A VO = VDD or VSS VDD = 5.5V, VO = VDD VDD = 5.5V VO = 0V = 1MHz @ 0V = 1MHz @ 0V = 1MHz @ 0V = 12MHz, CL = 50pF Note 5 2.4 -10 -90 -1 1110 -2000 1 -2000 -110 0.4 +10
V V A A A V V A mA mA pF pF pF mA mA
VOL VOH IOZ IOS CIN COUT CIO IDD QIDD
90 10 15 20 50 1.5
Notes: 1. Supplied as a design limit but not guaranteed or tested. 2. Not more than one output may be shorted at a time for a maximum duration of one second. 3. Measured only for initial qualification, and after process or design changes that could affect input/output capacitance. 4. Includes current through input pull-ups. Instantaneous surge currents on the order of 1 ampere can occur during output switching. Voltage supply should be adequately sized and decoupled to handle a large surge current. 5. All inputs with internal pull-ups or pull-downs should be left open circuit. All other inputs tied high or low.
BIT TIMES COMMAND WORD
123
45678 5
9 1
10 11 12 13 14 5
15 16 17 18 19 5
20 1 P 1 P
SYNC DATA WORD SYNC STATUS WORD SYNC
REMOTE TERMINAL T/R SUBADDRESS/MODE DATA WORD COUNT/ MODE CODE ADDRESS CODE 16 DATA 5
REMOTE TERMINAL ADDRESS
1
MESSAGE ERROR
1
INSTRUMENTATION
1
RESERVED SERVICE REQUEST
1
BROADCAST COMMAND RECEIVED
1
BUSY
1
SUBSYSTEM FLAG
1
DYNAMIC BUS CONTROL ACCEPTANCE
1
TERMINAL FLAG
1
PARITY
Figure 10. MIL-STD-1553B Word Formats
RTR-20
6.0 AC ELECTRICAL CHARACTERISTICS
(Over recommended operating conditions)
INPUT VIH MIN VIL MAX
1 1
IN-PHASE OUTPUT OUT-OF-PHASE OUTPUT BUS
ta
tb
2 2 2 2
VIH MIN VIL MAX VOH MIN VOL MAX VOH MIN VOL MAX VOH MIN VOL MAX
td te
tc
tg th SYMBOL ta tb tc td te tf tg th
INPUT to response INPUT to response INPUT to response INPUT to response INPUTto data valid INPUT to high Z INPUT to high Z INPUTto data valid
tf
PARAMETER
Notes: 1. Timing measurements made at (VIH MIN + VIL MAX)/2. 2. Timing measurements made at (VOL MAX + VOH MIN)/2. 3. Based on 50pF load. 4. Unless otherwise noted, all AC electrical characteristics are guaranteed by design or characterization.
Figure 11a. Typical Timing Measurements
5V IREF (source) 90% VREF 50pF 10% 0V IREF (sink) < 2ns Input Pulses
Note: 50pF including scope probe and test socket
3V
90%
10% < 2ns
Figure 11b. AC Test Loads and Input Waveforms
RTR-21
12MHz
CS t12a CTRL t12b RD/WR
t12i
t12j t12f
t12k t12c ADDR(9:0) t12d DATA(15:0) t12e OE Figure 12. Microprocessor RAM Read t12m t12l DATA VALID t12h t12g
SYMBOL t12a t12b t12c t12d t12e t12f t12g t12h t12i t12j t12k t12l t12m
PARAMETER CTRL set up wrt CS RD/WR set up wrt CS ADDR(9:0) Valid to CS (Address Set up) CS to DATA(15:0) Valid OE to DATA(15:0) Don't Care (Active) CS to CTRL Don't Care CS to ADDR(9:0) Don't Care OE to DATA(15:0) High Impedance CS to CS 2 CS to CS CS to RD/WR Don't Care CS to DATA(15:0) Invalid 3 OE to OE
1
MIN 10 10 10 --0 0 -220 85 0 25 65
MAX ---155 65 --40 5500 -----
UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns
Notes: 1. "wrt" defined as "with respect to." 2. The maximum amount of time that CS can be held low is 5500ns if the user has selected the 5.7s RBUSY option. For the 2.7s RBUSY option, the maximum CS low time is 2500ns. 3. Assumes OE is asserted.
RTR-22
12MHz
CS t13a CTRL t13b RD/WR t13c ADDR(9:0)
t13i
t13j t13k
t13f
t13g t13d DATA(15:0) VALID DATA t13h OE t13e Figure 13. Microprocessor RAM Write
SYMBOL t13a t13b t13c t13d t13e t13f t13g t13h t13i t13j t13k
PARAMETER CTRL set up wrt CS RD/WR set up wrt CS ADDR(9:0) Valid to CS(Address set up) DATA(15:0) Valid to CS(DATA set up) OE to DATA(15:0) High Impedance CS to RD/WR Don't Care CS to ADDR(9:0) Don't Care CS to DATA(15:0) Don't Care (Hold-time) CS to CS 1 CS to CS CS to CTRL Don't Care
MIN 10 10 10 0 40 0 0 20 180 85 0
MAX --------5500 ---
UNITS ns ns ns ns ns ns ns ns ns ns ns
Note: 1. The maximum amount of time that CS can be held low is 5500ns if the user has selected the 5.7ms RBUSY option. For the 2.7ms RBUSY option, the maximum CS low time is 2500ns.
RTR-23
12MHz
CS
t14c
t14a CTRL
t14e
t14b RD/WR t14f DATA(15:0) t14h VALID DATA t14d
OE t14g Figure 14. Control Register Write
SYMBOL t14a t14b t14c t14d t14e t14f t14g t14h
PARAMETER CTRL set up wrt CS RD/WR set up wrt CS CS to CS 1 CS to DATA(15:0) Don't Care (Hold-time) CS to CTRL Don't Care CS to RD/WR Don't Care OE to DATA(15:0) High Impedance DATA(15:0) Valid to CS (DATA set up)
MIN 0 0 50 0 0 0 40 0
MAX --5500 ------
UNITS ns ns ns ns ns ns ns ns
Note: 1. The maximum amount of time that CS can be held low is 5500ns if the user has selected the 5.7s RBUSY option. For the 2.7s RBUSY option, the maximum CS low time is 2500ns.
RTR-24
12MHz
CS
t15b
t15a CTRL
t15e
t15c RD/WR t15d DATA(15:0) VALID DATA t15f t15j
t15g OE
t15h t15i
Figure 15. Status Register Read
SYMBOL t15a t15b t15c t15d t15e t15f t15g t15h t15i t15j
PARAMETER CTRL set up wrt CS CS to CS 1 RD/WR set up wrt CS CS to DATA(15:0) Valid CS to CTRL Don't Care CS to RD/WR Don't Care OE to DATA(15:0) Don't Care (Active) OE to DATA(15:0) High Impedance OE to OE CS to DATA(15:0) Don't Care (Active)
MIN 0 65 0 -5 5 --65 25
MAX -5500 -65 --65 40 ---
UNITS ns ns ns ns ns ns ns ns ns ns
Note: 1. The maximum amount of time that CS can be held low is 5500ns if the user has selected the 5.7ms RBUSY option. For the 2.7ms RBUSY option, the maximum CS low time is 2500ns.
RTR-25
VALMSG
t16a TIMERON t16c
A/B BIPHASE OUTPUT ZERO t16b
COMSTR t16d
ILLCOM t16e t16g t16f
Figure 16. RT Fail-Safe Timer Signal Relationships
SYMBOL t16a t16b t16c t16d t16e t16f t16f t16g
PARAMETER VALMSG before TIMERON TIMERON before first BIPHASE OUT O TIMERON low pulse width (time-out) COMSTR to TIMERON VALMSG to ILLCOM COMSTR to ILLCOM 1 COMSTR to ILLCOM 2 ILLCOM to ILLCOM 3
MIN 0 1.2 727.3 ----500
MAX 35 -727.4 25 3.3 664 18.2 --
UNITS s s s s s s s s
Notes: 1. Mode code 2, 4, 5, 6, 7, or 18 received. 2. To suppress data word storage. 3. For transmit command illegalization.
RTR-26
12MHz CS COMMAND WORD BIPHASE IN MC/SA and MCSA(4:0) P
1
t17a
t17b t17c t17l
COMSTR t17d t17e BRDCST t17f t17g T/R t17h t17i VALMSG t17j t17k MERR
Note: 1. Measured from the mid-bit parity crossing.
Figure 17. Status Output Timing
SYMBOL t17a 4 t17b t17c 4 t17d t17e 4 t17f t17g 4 t17h t17i 4 t17j t17k 4 t17l
PARAMETER 12MHz to MC/SA Valid Command Word to MC/SA Valid 3 12MHz to COMSTR Command Word to COMSTR 3 12MHz to BRDCST Command Word to BRDCST 3 12MHz to T/R Valid Command Word to T/R Valid 3 12MHz to VALMSG Command Word to VALMSG 1, 2, 3 12MHz to MERR COMSTR to COMSTR
MIN 0 2.1 0 3.2 0 2.6 0 2.2 0 6.2 0 485
MAX 14 2.8 17 3.7 32 3.2 57 2.7 32 6.7 37 500
UNITS s s s s s s s s s s s s
Notes: 1. Receive last data word to Valid Message active (VALMSG). 2. Transmit command word to Valid Message active (VALMSG). 3. Command word measured from mid-bit crossing. 4. Guaranteed by test.
RTR-27
12MHz CS COMMAND WORD P BIPHASE IN RBUSY
t18a t18b t18c t18h
t18i
TERACT
t18d
t18e
RTRT
t18f
MRST
Note: 1. Measured from mid-bit parity crossing.
t18g
Figure 18. Status Output Timing
SYMBOL t18a t18b t18c 1 t18d t18e 1 t18f t18g t18h t18i
PARAMETER 12MHz to RBUSY Command Word to RBUSY 2 12MHz to TERACT Command Word to TERACT 2 12MHz to RTRT Command Word to RTRT 2 MRST to MRST RBUSY to RBUSY (2.7ms) (5.7ms) RBUSY to RBUSY (2.7ms) (5.7ms)
MIN -3.2 0 3.1 0 21.0 500 --3.10 240
MAX 37 3.8 37 3.7 32 22.0 -5.5 8.5 ---
UNITS ns s ns s ns s ns s s s s
Notes: 1. Guaranteed by test. 2. Command word measured from mid-bit crossing.
RTR-28
BIPHASE IN CS COMMAND WORD DATA WORD COMSTR T/R
P DS
DATA WORD
P
RBUSY TERACT BIPHASE OUT VALMSG
1
2
3
SS
STATUS
P
Notes: 1. Burst of 5 DMAs: read command pointer, store command word, update command pointer, read data word pointer, store command word. 2. Burst of 1 DMA: store data word. 3. Burst of 2 DMAs: store data word, update data word pointer. 4.Approximately 560ns per DMA access.
Figure 19a. Receive Command with Two Data Words
BIPHASE IN COMSTR
CS
COMMAND
P
T/R
RBUSY TERACT
1
2
3
BIPHASE OUT
SS
STATUS
P
DS
DATA
P
DS
DATA
P
VALMSG CS = Command sync SS = Status sync DS = Data sync P = Parity Notes: 1. Burst of 4 DMAs: read command pointer, store command word, update command pointer, read data word pointer. 2. Burst of 1 DMA: read data word. 3. Burst of 2 DMAs: read data word, update data word pointer. 4. Approximately 560ns per DMA access. Figure 19b. Transmit Command with Two Data Words
RTR-29
ADDR(9:0)
DATA(15:0)
UT1553B RTR
CONTROL
HOST SUBSYSTEM
UT63M125 1553 TRANSCEIVER
1553 BUS A
1553 BUS B
Figure 20a. RTR General System Diagram (Idle low interface)
RAO RAZ CHANNEL A TAO TAZ RTR RBO RBZ TBO TBZ
RXOUT RXOUT TXINHB TXIN TXIN CHANNEL A
UTMC 63M125 RXOUT RXOUT TXINHB TXIN TXIN CHANNEL B
CHANNEL B
TIMERON
Figure 20b. RTR Transceiver Interface Diagram
RTR-30
MC/SA
RTR
MCSA0 MCSA1 MCSA2 MCSA3 MCSA4 COMSTR BRDCST
ILLEGAL COMMAND DECODER
RTRT T/R ILLCOM
Figure 21. Mode Code/Subaddress Illegalization Circuit
RTR-31
Package Selection Guide Product BCRT BCRTM BCRTMP
RTI 24-pin DIP (single cavity) 36-pin DIP (dual cavity) 68-pin PGA 84-pin PGA 144-pin PGA 84-lead LCC 36-lead FP (dual cavity) (50-mil ctr) 84-lead FP 132-lead FP NOTE:
RTMP
RTR
RTS
XCVR X X
X X X X X X X1 X X1
X
X
X X
X X
1. 84LCC package is not available radiation-hardened.
Packaging-1
D 1.565 0.025 0.080 REF. (2 Places)
-A-
A 0.130 MAX. Q 0.050 0.010 L 0.130 0.010 A
0.040 REF.
E 1.565 0.025 -B-
0.100 REF. (4 Places)
PIN 1 I.D. (Geometry Optional) e 0.100 TYP. R P N M L K J H G F E D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PIN 1 I.D. (Geometry Optional) TOP VIEW
-CA (Base Plane) b 0.018 0.002 0.030 C A B 0.010 C 2 SIDE VIEW
1
D1/E1 1.400
BOTTOM VIEW
0.003 MIN. TYP.
Notes: 1. True position applies to pins at base plane (datum C). 2. True position applies at pin tips. 3. All package finishes are per MIL-M-38510. 4. Letter designations are for cross-reference to MIL-M-38510.
144-Pin Pingrid Array
Packaging-2
D/E 1.525 0.015 SQ. D1/E1 0.950 0.015 SQ. PIN 1 I.D. (Geometry Optional) e 0.025
A 0.110 0.006 A
SEE DETAIL A LEAD KOVAR TOP VIEW S1 0.005 MIN. TYP. L 0.250 MIN. REF.
A C 0.005 + 0.002 - 0.001 SIDE VIEW
0.014 MAX. REF. (At Braze Pads) DETAIL A
0.018 MAX. REF.
BOTTOM VIEW A-A
Notes: 1. All package finishes are per MIL-M-38510. 2. Letter designations are for cross-reference to MIL-M-38510.
132-Lead Flatpack (25-MIL Lead Spacing)
Packaging-3
D/E 1.150 0.015 SQ.
A 0.115 MAX. A1 0.080 0.008 A
PIN 1 I.D. (Geometry Optional) TOP VIEW
A SIDE VIEW L/L1 0.050 0.005 TYP.
h 0.040 x 45_ REF. (3 Places)
B1 0.025 0.003
e 0.050
J 0.020 X 455 REF.
e1 0.015 MIN. PIN 1 I.D. (Geometry Optional) BOTTOM VIEW A-A
Notes: 1. All package finishes are per MIL-M-38510. 2. Letter designations are for cross-reference to MIL-M-38510.
84-LCC
Packaging-4
D/E 1.810 0.015 SQ. D1/E1 1.150 0.012 SQ.
A 0.110 0.060 PIN 1 I.D. (Geometry Optional) A
e 0.050
b 0.016 0.002
SEE DETAIL A A LEAD KOVAR
TOP VIEW L 0.260 MIN. REF.
C 0.007 0.001 SIDE VIEW
S1 0.005 MIN. TYP.
0.018 MAX. REF. 0.014 MAX. REF. (At Braze Pads) BOTTOM VIEW A-A
Notes: 1. All package finishes are per MIL-M-38510. 2. Letter designations are for cross-reference to MIL-M-38510.
DETAIL A
84-Lead Flatpack (50-MIL Lead Spacing)
Packaging-5
D 1.100 0.020
-A-
A 0.130 MAX. Q 0.050 0.010 A
L 0.130 0.010 E 1.100 0.020
-B-
PIN 1 I.D. (Geometry Optional) TOP VIEW -C(Base Plane)
e 0.100 TYP. L K J H G D1/ F E D 1.000
A b 0.018 0.002 0.030 C A B 0.010 C 2 SIDE VIEW
1
PIN 1 I.D. (Geometry Optional) BOTTOM VIEW A-A
1
2
3
4
5
6
7
8 9 10 11 0.003 MIN.
Notes: 1. True position applies to pins at base plane (datum C). 2. True position applies at pin tips. 3. All packages finishes are per MIL-M-38510. 4. Letter designations are for cross-reference to MIL-M-38510.
84-Pin Pingrid Array
Packaging-6
D 1.100 0.020
-A-
A 0.130 MAX. Q 0.050 0.010 A L 0.130 0.010
E 1.100 0.020 -B-
PIN 1 I.D. (Geometry Optional) TOP e 0.100 TYP.
-C(Base Plane)
A
b 0.010 0.002 0.030 C A B 0.010 C 2 SIDE VIEW
1
L K J H G F E D C B A
123456 PIN 1 I.D. (Geometry Optional) 7 8 9 10 11
D1/E1 1.00
0.003 MIN. TYP.
BOTTOM VIEW A-A
Notes: 1 True position applies to pins at base plane (datum C). 2 True position applies at pin tips. 3. All packages finishes are per MIL-M-38510. 4. Letter designations are for cross-reference to MIL-M-38510.
68-Pin Pingrid Array
Packaging-7
E 0.750 0.015
L 0.490 MIN.
b 0.015 0.002
D 1.800 0.025
e 0.10
PIN 1 I.D. (Geometry Optional) TOP VIEW c 0.008 A 0.130 MAX. END VIEW
Notes: 1 All package finishes are per MIL-M-38510. 2. It is recommended that package ceramic be mounted to a heat removal rail located on the printed circuit board. A thermally conductive material such as MERECO XLN-589 or equivalent should be used. 3. Letter designations are for cross-reference to MIL-M-38510.
+ 0.002 - 0.001
Q 0.080 0.010 (At Ceramic Body)
36-Lead Flatpack, Dual Cavity (100-MIL Lead Spacing)
Packaging-8
E 0.700 + 0.015
L 0.330 MIN.
b 0.016 + 0.002
D 1.000 0.025 e 0.050
PIN 1 I.D (Geometry Optional)
TOP
+ 0.002 c 0.007 - 0.001 A 0.100 MAX. Q 0.070 + 0.010 (At Ceramic Body)
END
Notes: 1. All package finishes are per MIL-M-38510. 2. It is recommended that package ceramic be mounted to a heat removal rail located on the printed circuit board. A thermally conductive material such as MERECO XLN-589 or equivalent should be used. 3. Letter designations are for cross-reference to MIL-M-38510.
36-Lead Flatpack, Dual Cavity (50-MIL Lead Spacing)
Packaging-9
E 0.590 0.012
S1 0.005 MIN.
S2 0.005 MAX.
e 0.100
D 1.800 0.025
b 0.018 0.002
PIN 1 I.D. (Geometry Optional) TOP VIEW
A 0.155 MAX. SIDE VIEW
L/L1 0.150 MIN.
C 0.010 +- 0.002 0.001 E1 0.600 + 0.010 (At Seating Plane) END VIEW
Notes: 1. All package finishes are per MIL-M-38510. 2. It is recommended that package ceramic be mounted to a heat removal rail located on the printed circuit board. A thermally conductive material such as MERECO XLN-589 or equivalent should be used. 3. Letter designations are for cross-reference to MIL-M-38510.
36-Lead Side-Brazed DIP, Dual Cavity
Packaging-10
E 0.590 0.015
S1 0.005 MIN.
S2 0.005 MAX. e 0.100
D 1.200 0.025 b 0.018 0.002
PIN 1 I.D. (Geometry Optional)
A 0.140 MAX. SIDE VIEW
L/L1 0.150 MIN.
TOP VIEW
+ 0.002 C 0.010 - 0.001 E1 0.600 + 0.010 (At Seating Plane)
Notes: 1. All package finishes are per MIL-M-38510. 2. It is recommended that package ceramic be mounted to a heat removal rail located on the printed circuit board. A thermally conductive material such as MERECO XLN-589 or equivalent should be used. 3. Letter designations are for cross-reference to MIL-M-38510.
END VIEW 24-Lead Side-Brazed DIP, Single Cavity
Packaging-11
ORDERING INFORMATION UT1553B RTR Remote Terminal with RAM: S 5962 * * * * *
Lead Finish: (A) = Solder (C) = Gold (X) = Optional Case Outline: (X) = 68 pin PGA Class Designator: (-) = Blank or No field is QML Q Drawing Number: 8957601 Total Dose: (-) = None Federal Stock Class Designator: No options
Notes: 1. Lead finish (A, C, or X) must be specified. 2. If an "X" is specified when ordering, part marking will match the lead finish and will be either "A" (solder) or "C" (gold). 3. For QML Q product, the Q designator is intentionally left blank in the SMD number (e.g. 5962-8957601XC).
UT1553B RTR Remote Terminal with RAM
No UT Part Number- *
*
Lead Finish: (A) = Solder (C) = Gold (X) = Optional Package Type: (G) = 68 pin PGA
UTMC Core Part Number
Notes: 1. Lead finish (A, C, or X) must be specified. 2. If an "X" is specified when ordering, part marking will match the lead finish and will be either "A" (solder) or "C" (gold).


▲Up To Search▲   

 
Price & Availability of 5962-8957601-XC

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X